Tariff Concession Orders

GATE AND/OR PLUG VALVES, LAUNDER, manual

GATE VALVES, conforming to ASME/ANSI B16.34:2013, including ALL 
of the following:
  (a) working pressure class 300, 600, 800, or 1 500;
  (b) valve body AND bonnet consisting of ANY of the following:
       (i) ASTM A217 grade WC6 OR C5 cast steel;
      (ii) ASTM A105 forged steel; 
     (iii) ASTM A351 grade CF8M cast stainless steel;
      (iv) ASTM A216 grade WCB carbon steel,
  (c) valve size or nominal diameter (DN) 40, 50, 80, 150, 
      200

SHUT-OFF AND REGULATING VALVES, including ALL of the following:
  (a) cast OR non-alloy steel housing;
  (b) nominal size (DN) NOT less than 6 and NOT greater than 200;
  (c) temperature range NOT less than minus 60 degrees Celsius  
      and NOT greater than plus 150 degrees Celsius

VALVES, DIAPHRAGM, having ALL of the following:
  (a) nominal size (DN) NOT greater than 150;
  (b) forged AND/OR machined stainless steel grade EN 1.4435 
      (AISI 316L) body; 
  (c) manual AND/OR motorised AND/OR pneumatic actuation

KITS, RETAINER VALVE UPGRADE CONVERSION, SUBSEA TEST TREE, 
consisting of ALL of the following:
  (a) ball operating casing;
  (b) steel alloy valve ball;
  (c) NOT less than two valve pins

HYDRAULIC CONTROL VALVES, DIRECTIONAL, stackable, load sensing, 
pressure-compensated, including ALL of the following:
  (a) working pressure NOT greater than 350 bar;
  (b) pump flow NOT greater than 210 litres per minute per inlet 
      section;
  (c) spool actuators; 
  (d) relief valves;
  (e) pilot restrictor

VALVES, PNEUMATIC SLIDE GATE, having BOTH of the following:
  (a) inlet AND outlet section NOT greater than 600 mm;
  (b) heat rated to a maximum of 800 degrees Celsius

GATE VALVES, OIL AND/OR GAS WELL, manual, complying with 
American Petroleum Institute Specification 6A (API 6A, including 
ALL of the following:
  (a) bore NOT less than 4 cm and NOT greater than 20 cm;
  (b) working pressure NOT less than 2 000 psi and NOT greater
      than 20 000 psi;
  (c) threaded OR studded flange connections;
  (d) split OR segmented OR solid slab gate;
  (e) weight NOT less than 20 kg and NOT greater than 4 000 kg

VALVES, HYDRAULIC AND/OR PNEUMATIC ACTUATED, OIL AND/OR GAS 
WELL, complying with American Petroleum Institute 
Specification 6A (API 6A); including ALL of the following:
  (a) working pressure NOT less than 2 000 psi and NOT greater
      than 20 000 psi;
  (b) bore NOT less than 4 cm and NOT greater than 20 cm;
  (c) fail-safe valve closure;
  (d) actuator operating line pressures NOT less than 30 psi and
      NOT greater than 6 000 psi;
  (e) threaded OR flanged end connections;
  (f) weight NOT less than 20 kg and NOT greater than 4 000 kg

CASING HEAD, OIL AND/OR GAS WELL, complying with American 
Petroleum Institute Specification 6A (API 6A), with OR without 
ANY of the following:
  (a) threaded AND/OR flanged end connections;
  (b) flanged OR threaded outlets;
  (c) lock down mechanism;
  (d) studs;
  (e) nuts;
  (f) outlet valves

TUBING HEAD, OIL AND/OR GAS WELL, with OR without screw lock 
down mechanism, complying with American Petroleum Institute 
Specification 6A (API 6A), having BOTH of the following:
  (a) threaded AND/OR flanged end connections;
  (b) flanged OR threaded outlets

RELAY VALVE ASSEMBLIES, GAS OPERATED WATER HEATER, having ALL 
of the following:
  (a) body;
  (b) seals;
  (c) cover;
  (d) support ring;
  (e) diaphragm;
  (f) valves;
  (g) valve spring;
  (h) screws;
  (i) washer;
  (j) seat;
  (k) plug;
  (l) compression connector

DISTRIBUTOR BOXES, AIR CONDITIONING REFRIGERANT, including ALL 
of the following:
  (a) solenoid valve assemblies;
  (b) printed circuit boards;
  (c) single or multiple reducers;
  (d) wiring terminals

DOUBLE CONE VALVES, SINTER PLANT WASTE GAS MAINS

VALVES, BUTTERFLY, gear OR lever actuated, having ALL of the 
following:
  (a) shouldered OR grooved end connection;
  (b) stainless steel OR bronze OR ductile iron discs;
  (c) nominal bore diameter NOT less than 50 mm and NOT
      greater than 300 mm;
  (d) nitrile butadiene rubber lined body

CHRISTMAS TREES, OIL AND/OR GAS WELL, ONSHORE, assembled OR 
unassembled, with OR without wellhead to Christmas tree 
connectors

VALVE ASSEMBLIES, OIL AND/OR GAS WELL, ONSHORE, consisting of 
BOTH of the following:
  (a) valves;
  (b) pipes,
with OR without oil AND/OR gas Christmas tree

GATE VALVES, conforming to American Society of Mechanical 
Engineers (ASME) standard B16.34-2013 (including any subsequent 
amendments), carbon steel, stainless steel OR alloy steel valve 
body, having ALL of the following:
  (a pressure-temperature rated to ASME Standard Class 2500;
  (b) butt weld end connections with face to face dimensions as 
      per ASME B16.10;
  (c) fitted with OR without bypass valves;
  (d) one OR more of the following valve actuator mechanisms:
          (i) handwheel;
         (ii) gear operator;
        (iii) electric motor

VALVES, BUTTERFLY, ductile iron OR ductile cast iron, double 
offset, bi-directional sealing, including BOTH of the following:
  (a) pneumatic OR manual eccentric rubber sealing flange;
  (b) valve bore size NOT less than 50 cm and NOT greater than
      700 cm

VALVES, half ball, pneumatic, having BOTH of the following:
  (a) chromium plating;
  (b) nitride treatment

RESERVOIR PACKER CONTROL MODULES, OIL AND/OR GAS WELL, whether 
OR not assembled, including BOTH of the following:
  (a) electronics cartridge;
  (b) valve block

VALVES, solenoid activated, pivoting armature AND/OR rocker, 
isolating diaphragm, with OR without manifold

MARINE RISER DIVERTERS, OIL AND GAS, FLOATING DRILLING MODULES

TAPS, BEVERAGE DISPENSER, stainless steel, having ALL of the 
following:
  (a) O-rings;
  (b) gaskets;
  (c) dispenser valve;
  (d) valve internal bore hole diameter NOT less than 10 mm;
  (e) tap cast body

KELLY VALVES, OIL AND/OR GAS WELL, upper AND/OR lower, including 
ALL of the following:
  (a)  working pressure rating NOT less than 325 bar; 
  (b) stainless steel ball;
  (c) operating wrench

VALVES, DIVERTER

VALVES, BUTTERFLY, having ALL of the following:
  (a) gear OR lever actuated;
  (b) shouldered OR grooved end connection;
  (c) stainless steel OR bronze OR ductile iron discs;
  (d) bore diameter NOT less than 50 mm and NOT greater than
      300 mm;
  (e) ethylene propylene diene monomer encapsulated seats

VALVES, BUTTERFLY, triple eccentric metal seated

VALVES, INSTRUMENT ISOLATION, double block AND bleed

VALVES, SAFETY, SUBSURFACE, OIL AND/OR GAS WELL, surface 
controlled, retrievable, whether OR not assembled

VALVES, CIRCULATING, DOWNHOLE ANTI-SWAB, whether OR not 
assembled, having a collapse pressure rating of NOT less than 
400 bar

VALVES, AUTOMOTIVE AIR BRAKE SYSTEM, being ANY of the following:
  (a) spring brake valves;
  (b) pressure protection valves;
  (c) foot valves

VALVES, GATE, SUBSEA CHOKE AND KILL LINE, hydraulically activated

VALVES, BUTTERFLY, lug type, gear OR lever operated, complying 
with BOTH of the following:
  (a) American Society of Mechanical Engineers 
      standard B16.34-2004, Class 150;
  (b) American Petroleum Institute API Standard 609, 
      Seventh Edition, October 2010, Category A

DISTRIBUTOR BOXES, AIR CONDITIONING REFRIGERANT, including ALL 
of the following:
  (a) electrical expansion valve;
  (b) printed circuit board controller;
  (c) insulation;
  (d) flare joints

VALVES, BUTTERFLY, lug type, gear operated, having BOTH of the 
following:
  (a) complying with American Society of Mechanical Engineers  
      Standard B16.34 (ASME B16.34) Class 150;
  (b) fabricated to American Petroleum Institute Standard 609 
      (API 609) Category A

MANIFOLDS, INJECTION WELL, including ANY of the following:
  (a) shutdown valves;
  (b) thermal relief valves;
  (c) depressurising valves;
  (d) check valves;
  (e) choke valves

COUPLINGS, steel, quick connect, capable of operating at 
pressures exceeding 34 000 kPa

HEAT RECOVERY MODULES, AIR CONDITIONING, direct expansion, 
having BOTH of the following:
  (a) variable refrigerant flow;
  (b) three pipe system

CHOKE MANIFOLDS, OIL AND/OR GAS WELL, skid mounted, having a 
working pressure rating NOT less than 655 bar, including BOTH of 
the following:
  (a) NOT less than four gate valves;
  (b) adjustable AND fixed choke valves

VALVES, BALL, flanged end connection, split body, lever OR 
gearbox operated, trunnion mounted ball, having BOTH of the 
following:
  (a) valve outside diameter NOT less than 12 mm and NOT greater
      than 265 mm; 
  (b) compliance with American Society of Mechanical Engineers
      B16.34-2004 (ASME B16.34-2004)

VALVES, MONOFLANGE, DOUBLE BLOCK AND BLEED, complying with 
American Petroleum Institute standard 6A(API 6A)

VALVES, DUAL FLOW ANNULAR, OIL AND/OR GAS WELL, hydraulic, 
downhole, whether OR not assembled, having a working pressure 
rating of NOT less than 390 bar at a temperature between 115 
degrees Celsius and 130 degrees Celsius

FORMATION ISOLATION VALVES, DOWNHOLE, OIL AND/OR GAS WELL, 
whether OR not assembled, having a differential pressure of NOT 
less than 325 Bar

KITS, TOILET CISTERN, with OR without stopcock, including ALL of 
the following:
  (a) bracket;
  (b) flexible hose;
  (c) plug set, consisting of ALL of the following:
         (i) stepped flange;
        (ii) nut;
       (iii) plastic stop plug,
  (d) inlet valve bayonet

AERATING AND CHILLING WATER DISPENSING MACHINES, mains water 
connected, including ALL of the following:
  (a) stainless steel cabinet;
  (b) water chiller;
  (c) water dispensing taps;
  (d) water carbonator;
  (e) CO2 gas connector

VALVES, BALL, copper alloy, complying with Australian Standard 
4796-2001 (AS 4796-2001)

TUBING HEAD ASSEMBLIES, SUBSEA OIL AND GAS WELL, including BOTH 
of the following:
  (a) wellhead connector;
  (b) wellhead hub

VALVES, REFRIGERATION AND AIR CONDITIONING, being ANY of the 
following:
  (a) packless line valves;
  (b) packed capped valves;
  (c) capped line valves;
  (d) service valves;
  (e) compressor valves

VALVES, positive AND/OR negative pressure, being ANY of the 
following:
  (a) blow-through airlock;
  (b) discharge airlock;
  (c) tangential airlock
Op. 15.10.12	- TC 1239266

VALVES, THERMOSTATIC EXPANSION, AUTOMOTIVE ENGINE COOLING CONTROL

VALVES, INLET AND/OR OUTLET, TOILET CISTERN

VALVES, butterfly, triple offset, stainless steel OR carbon 
steel, having BOTH of the following:
  (a) double flange mounting;
  (b) bore size NOT less than 75 mm

VALVES, BALL, surface, trunnion, actuated, flanged end, split 
body having a diameter NOT greater than 250 mm

BALL VALVES, brass, quarter turn, having ALL of the following:
  (a) integral y-strainer;
  (b) locking lever;
  (c) 15 mm (1/2") or 20 mm (3/4") or 25 mm (1") female thread;
  (d) pressure rating NOT greater than 2 000 kPa

GATE VALVES, manually operated, having BOTH of the following:
  (a) working pressure NOT less than 20 MPa and NOT greater  
      than 142 MPa;
  (b) weight NOT less than 300 kg and NOT greater than 
      4 000 kg

METERING VALVES, DUST DISCHARGE VALVE, BLAST FURNACE

VALVES, ROTARY, having a maximum flow capacity NOT greater than 
130 cubic metres per hour

VALVES, NEEDLE, SUBSEA

TEST PLUGS, TEMPERATURE AND/OR PRESSURE, WATER AND/OR GAS PIPE

VALVES, PIPE SLEEVE, OIL AND/OR GAS PRODUCTION, hydraulic, 
drillable AND/OR closable, having a ball seat

HYDRAULIC VALVE SYSTEM, incorporating a control valve assembly, 
including NOT less than three of the following:
  (a) hose AND fittings;
  (b) electric joystick;
  (c) electronic valve controller;
  (d) pre-set flow control;
  (e) integrated multi-coupler;
  (f) accumulator

VALVES, SUBSEA OIL AND GAS WELL TESTING, being ANY of the 
following:
  (a) retainer valves;
  (b) ball valves; 
  (c) bleed off valves

VALVES, DOSING, DIESEL EXHAUST

VALVES, BALL, full bore, antistatic controlled, including ALL 
of the following:
  (a) floating OR trunnion mounted ball;
  (b) carbon steel body;
  (c) split body OR top entry;
  (d) uni-directional OR bi-directional

VALVES, GATE, water cooled body, with OR without actuators

VALVES, single piece cast iron body, stainless steel spindle, 
having a maximum operating pressure rating NOT less than 2 450 
kPa and NOT greater than 5 400 kPa being EITHER of the following:
  (a) shouldered end connection butterfly valves; 
  (b) screw AND/OR shouldered end connection ball valves

VALVES, THERMOSTATIC, REFRIGERATION AND/OR AIR CONDITIONING

THROTTLE BODIES, with OR without throttle position sensor

VALVES, incorporating BOTH of the following:
  (a) conical discharge valve;
  (b) disc suction valve

VALVES, CONICAL, incorporating BOTH of the following:
  (a) conical discharge valve;  
  (b) conical suction valve

FOOT ACTUATED VALVES

VALVES, THERMOSTATIC EXPANSION, AUTOMOTIVE AIR CONDITIONING

CHRISTMAS TREES, OIL AND GAS WELL, SUBSEA

VALVES, BUTTERFLY, double flanged, ductile iron, including BOTH  
the following:
  (a) bore size NOT less than 600 mm and NOT greater than 
      1 200 mm;
  (b) pressure rating greater than Pressure Nominal (PN) 25

VALVES, PLUG, pressure balanced, lubricated

VALVES, SHUT OFF, hydraulic control, pressure differential 
activated

VALVES, STOP, bellows sealed, in-line stop mechanism, manually 
operated

VALVES, multi-port, 6-way, having BOTH of the following:
  (a) sight glass;
  (b) oil filled pressure gauge

VALVES, EXHAUST GAS RECIRCULATION

GATE VALVES, having a diameter NOT less than 1 200 mm

VALVE ASSEMBLIES, ACTUATED, complying with BOTH American 
Society of Mechanical Engineers standard ASME B16.34a-1998 AND 
American Petroleum Institute standard API Specification 6FA, 
July 2006, including ALL of the following:
  (a) split body trunnion mounted ball valve;
  (b) pneumatic spring return actuator;
  (c) limit switch;
  (d) three way solenoid valve

VALVES, METERING, GAS AND LIQUID FUEL, DC voltage NOT greater 
than 32 V

VALVES, FLOW CONTROL, DOWNHOLE, surface actuated, having a 
maximum working pressure NOT less than 10 MPa

VALVES, BALL, flanged end connection, split body, lockable, 
lever OR gearbox operated, trunnion mounted ball OR floating 
ball, having ALL of the following:
  (a) DN (diameter nominal) NOT less than 15 mm and NOT greater
      than 250 mm;
  (b) rating complying with American Society of Mechanical
      Engineers B16.34a-1998 (ASME B16.34a-1998);
  (c) inlet pressure NOT less than 1 800 kPA at 38 degrees
      Celsius

VALVES, FLOW CONTROL, downhole, binary

VALVES, SLOW RETURN, BOOM AND BUCKET HYDRAULIC CYLINDER

VALVES, SAMPLING, carbon OR alloy steel, forged, manually 
operated, complying with ALL of the following:
  (a) manufactured in accordance with American National Standard 
      Institute B16.34-1996 (ANSI B16.34-1996);
  (b) pressure rating to ANY of the following:
       (i) ANSI 150;
      (ii) ANSI 300;
     (iii) ANSI 600,
  (c) end connections either screwed or flanged

VALVES, AXIAL FLOW, having a bore diameter NOT less than 140 mm

VALVES, BALL, flanged end connection, split body, lockable, 
lever OR gearbox operated, trunnion mounted ball OR floating 
ball, having ALL of the following:
  (a) DN(Diameter Nominal) NOT less than 15 mm and NOT greater 
      than 200 mm;
  (b) rating complying with American Society of Mechanical
      Engineers ASME B16.34a-1998;
  (c) inlet pressure NOT less than 1 800 kPA at 38 degrees 
      Celsius

VALVES, BUTTERFLY, LUGGED WAFER, lever operated, bi-directional 
tight shut off, having ALL of the following:
  (a) DN(Diameter Nominal) NOT less than 50 mm and NOT greater 
      than  200 mm; 
  (b) synthetic rubber seat;
  (c) cast carbon steel body complying with American Society for 
      Testing and Materials ASTM A216/A 216M-93(Re-approved 
      2003), WCB Grade;
  (d) aluminium bronze disc;
  (e) rating complying with American Society of Mechanical
      Engineers ASME B16.34a-1998, Class 150

BUTTERFLY SPLIT CONTAINMENT VALVES

VALVES, GATE, brass, manually operated, having BOTH of the 
following:
  (a) screwed in bonnet;
  (b) British Standard Pipe (BSP) diameter NOT less than 12.7 mm 
      and NOT greater than 50.8 mm

VALVES, BALL, DEZINCIFICATION (DZR) brass, having ALL of the 
following:
  (a) 1/4 turn on/off operation;
  (b British Standard Pipe (BSP) diameter NOT less than 6 mm and
     NOT greater than 100 mm;
  (c) watermark certification;
  (d) stainless steel handles and lock nuts

VALVES, BALL, nickel plated brass, having ALL of the following:
  (a) 1/4 turn on/off operation;
  (b) British Standard Pipe (BSP) diameter NOT less than 6 mm 
      and NOT greater than 100 mm;
  (c) stainless steel handles and lock nuts

VALVES, BALL, brass, having ALL of the following:
  (a) 1/4 turn on/off operation;
  (b) compression fitting NOT less than 12.7 mm and NOT greater 
      than 50.8 mm;
  (c) diameter NOT less than 15 mm and NOT greater than 54 mm

VALVES, BALL, cast iron, comprising ALL of the following:
  (a) working pressures NOT exceeding 3.4 MPa (500 psi);
  (b) with OR without lockout;
  (c) bore end dimensions NOT less than 19 mm and NOT greater
      than 51 mm;
  (d) end connection types, including ANY of the following:
       (i) BSPF x BSPF (British Standard Pipe Female);
      (ii) A-type x A-type (European Air Coupling);
     (iii) BSPF x A-type;
      (iv) SL x SL (Surelock);
       (v) NPT x NPT (National Pipe Thread USA);
      (vi) Shouldered Coupling x BSPF

VALVES, BALL, bore diameter NOT less than 475 mm

VALVES, PASSENGER TRAIN BRAKE SYSTEM, being ANY of the following:
  (a) relay valves;
  (b) dead man valves;
  (c) emergency brake valves;
  (d) solenoid valves

VALVES, ELECTRICAL DIRECTIONAL CONTROL PRESSURE REGULATING, 
consisting of BOTH of the following:
  (a) force control solenoids;
  (b) valve hydraulic module

TEST TREE VALVES, SUBSEA, OIL OR GAS WELL, hydraulic signal, 
surface control

REGULATORS, PRESSURE CONTROLLING, pilot spring actuated

ROTOLOCK VALVES, REFRIGERATION AND/OR AIR-CONDITIONING, having 
ALL of the following:
  (a) single rotating lock seal joint;
  (b) NOT less than two access ports with seal cap;
  (c) inlet connection NOT less than 12.7 mm (1/2") and NOT 
      greater than 57.15 mm (2 1/4")

VALVES, WELDED BALL, bi-directional, comprising ALL of the 
following:
  (a) trunnion mounted ball;
  (b) floating seats;
  (c) triple barrier sealing stem;
  (d) adaptor plate

VALVES, BALL, top-entry, comprising ALL of the following:
  (a) triple barrier stem seals;
  (b) anti-blow out stems;
  (c) metal backed self lubricating sleeves and
      bearings and thrust washers;
  (d) trunnion mounted balls;
  (e) double piston effect seats

VALVES, SIDE ENTRY BALL, split body, comprising ALL of the 
following:
  (a) anti-blowout stem;
  (b) uni-directional seat and/or bi-directional seat;
  (c) antistatic control

BOOSTERS, FIRE MAINS, being connection devices

NOZZLES, LIQUID FUEL, with OR without built in vapour recovery

VALVES, O-PORT OR THROUGH CONDUIT, being ANY of the following:
  (a) steel construction complying with ALL of the following:
         (i) pressure temperature rating to American National
             Standards Institute Specification B16.34 
             (ANSI B16.34);
        (ii) bore NOT greater than 200 mm;
       (iii) maximum operating pressure NOT less than 700 kPa
  (b) steel construction complying with ALL of the following:
         (i) pressure temperature rating to American National
             Standards Institute Specification B16.34
             (ANSI B16.34);
        (ii) bore diameter NOT less than 250 mm and
             NOT greater than 400 mm;
       (iii) maximum operating pressure NOT less than 1 650 kPa
  (c) steel construction complying with ALL of the following:
         (i) pressure temperature rating to American National
             Standards Institute Specification B16.34 
             (ANSI B16.34);
        (ii) bore diameter NOT less than 450 mm and
             NOT greater than 600 mm;
       (iii) maximum operating pressure NOT less than 1 050 kPa
  (d) steel construction complying with ALL of the following:
         (i) pressure temperature rating to American National
             Standards Institute Specification B16.34
             (ANSI B16.34);
        (ii) bore diameter NOT less than 700 mm;
       (iii) maximum operating pressure NOT less than 650 kPa
  (e) high alloy steel, hastelloy, duplex, inconel, zirconium or
      titanium construction complying with ALL of the following:
         (i) pressure temperature rating to American National
             Standards Institute Specification B16.34
             (ANSI B16.34);
        (ii) bore size NOT less than 50 mm and NOT greater than
             1 800 mm

CONNECTORS, OFFSHORE PLATFORM, CHEMICAL INJECTION AND HYDRAULIC 
FLUID UMBILICAL, comprising ALL of the following:
  (a) manual fluid isolation valves;
  (b) pressure gauges;
  (c) umbilical to platform fluid supply connector

WELLHEAD FLOWBASES, SUBSEA, HYDROCARBON PROCESSING

VALVES, WORKOVER SYSTEM, OIL AND GAS WELL, being ANY of the 
following:
  (a) emergency disconnect package;
  (b) lower riser package;
  (c) surface flow tree

VALVES, FIRE HYDRANT, to Australian Standard 2419.2 (AS 2419.2)

INFLATORS AND/OR DEFLATORS, TYRE, incorporating a gauge, having 
a pressure rating NOT greater than 1 500 kPa

LINE BLIND, PIPELINE

VALVES, FLAPPER, OIL AND GAS EXPLORATION AND PRODUCTION, 
hydraulically controlled, having a fail-safe spring closure

TIMERS, TAP, spring wound with a diaphragm

VALVES, BUTTERFLY, double flanged, cast steel body and disc, 
comprising ALL of the following:
  (a) bore NOT less than 1 200 mm;
  (b) rated PN30 (30 bar, 435 psi);
  (c) hydraulic actuation;
  (d) bi-directional flow

VALVES, GATE, bronze, manually operated, having BOTH of the 
following:
  (a) screwed-in bonnet;
  (b) solder joint tubing ends

VALVES, BALL, double block AND bleed, having ALL of the 
following:
  (a) pressure rating complying to Australian and New Zealand 
      Standard B16.34 (ANSI B16.34); 
  (b) flanged end connections complying to Australian and New
      Zealand Standard B16.5 (ANSI B16.5)

COUPLINGS, hydraulic, being EITHER of the following:
  (a) couplers;
  (b) nipples

REGULATORS, WELDING, GAS

BY-PASS VALVES, NON-ADVANCING, MULTI-CYCLE, OIL AND GAS WELL

CONNECTORS, STAB, SUBSEA PIPELINE AND/OR MANIFOLD, comprising 
BOTH of the following:
  (a) female receptacle incorporating a valve;
  (b) male stab

VALVES, STEAM, PARALLEL SLIDE

TAPS, MIXER, single lever, having ALL of the following:
  (a) ceramic cartridges; 
  (b) operating temperature NOT greater than 80 degrees Celsius;
  (c) adjustable anti-scold water stop rings

PREVENTERS, BLOWOUT, OIL RIG, annular

FLOWHEADS, subsea well testing, oil and/or gas, having a minimum 
working pressure NOT less than 650 bar

COUPLINGS, BREAKAWAY, MARINE

VALVES, BALL, BRASS (NICKEL-PLATED) actuator driven

TAPS, MIXER, HOT AND COLD WATER

COUPLERS AND/OR NIPPLES, having a ball valve OR poppet valve

VALVES, OIL CONTROL, solenoid operated

VALVES, RELAY, AIR BRAKE, TRUCK AND/OR TRAILER

VALVES, GATE, SUBSEA, complying with American Petroleum 
Institute Standard (API) specification 6D

NOZZLES, FIRE FIGHTING

VALVES, BALL, AIR CONDITIONER REFRIGERANT ISOLATION

VALVES, SOLENOID, REFRIGERATION

MANIFOLDS, SUBSEA

KITS, PNEUMATIC TOOL, comprising ALL of the following:
(a) paint spray guns;
(b) blow guns;
(c) tyre inflators and gauges;
(d) air hoses;
(e) dust masks;
(f) air line fittings;
(g) wire brushes;
(h) blow gun nozzles

DIVERTERS, FLOW, AIR GRAVITY CONVEYOR, PNEUMATIC

VALVES, BUTTERFLY, hot shell, variable orifice

VALVES, CONTROL, ELECTRONIC THROTTLE, incorporating 12 volt DC 
motor

VALVES, HYDRAULIC CONTROL, SNOW MAKING

VALVES, HYDRAULIC CONTROL, POWER STEERING GEAR

VALVES, BALL, SUBSEA

VALVES, BUTTERFLY, RECUPERATOR, having BOTH of the following:
  (a) diameter NOT less than 900 mm;
  (b) temperature rating NOT less than 390 degrees celsius

VALVES, BALL, NICKEL OR COBALT AUTOCLAVE DRAIN, 316 stainless
 steel, on-off

VALVES, BALL, three-way, stainless steel, "L" or "T" ported,
 1/4 turn, having female thread sizes from 10 mm (3/8" BSP)
 to 50 mm (2" BSP) (both inclusive)

VALVES, GLOBE, manually operated, having ALL of the following:
   (a) bore size NOT exceeding 50 mm;
   (b) bronze construction;
   (c) flow measure;
   (d) variable calibration pre-setting;
   (e) pre-selected flow rate at each setting

VALVES, GATE OR GLOBE, carbon or alloy steel, forged, manually
 operated, complying with ALL of the following:
   (a) manufactured in accordance with standard ANSI B16.34;
   (b) pressure rating to one of the following:
           (i) ANSI 600;
          (ii) ANSI 900;
         (iii) ANSI 1500;
          (iv) ANSI 2500;
           (v) ANSI 4500;
   (c) end connections either screwed, socket welded, flanged or
       buttwelded

VALVES, BALL, SEVERE SERVICE, slurry

VALVES, directional poppet, with solenoid operation for pressure of
 40 MPa or greater and leak free in closed flow direction

VALVES, KEG SPEAR COUPLING

VALVES, 50 mm nominal diameter, air or gas relief, having ALL of the
 following:
   (a) maximum operating pressure of 1 200 kPa;
   (b) fibreglass reinforced nylon body;
   (c) release rate up to 125 cubic metres per hour;
   (d) mechanism incorporating:
         (i) non-metallic flexible rolling seal with non-metallic
             attached stem; and
        (ii) float of foamed polypropylene;
   (e) kinetic air release valve and automatic air release valve
       in a single body;
   (f) able to admit air during line emptying

VALVES, PILOT CONTROL UNITS, giving proportional output pressure
 for the remote control of valves, pumps and motors

VALVES, PLUG, pressure rated to 13 500 kPa OR greater, temperature
 rated from -23 degrees C to 204 degrees C

VALVES, SOLENOID, 12 V DC or 24 V AC, 3 way pilot, direct or
 reverse mode, body made of non-corrosive glass reinforced nylon
 with built in hydraulic relay which converts electrical signal
 to hydraulic command

CONNECTORS, SAFETY CHECK, LPG, 31.75 mm (1 1/4") ACME connection
 incorporating internal check valve

CHUCKS, AIR, AUTOMOTIVE TYRE INFLATION

VALVES, WITHDRAWAL, LIQUID OR VAPOUR, LIQUEFIED PETROLEUM GAS,
 having ALL of the following:
   (a) integral excess check valve and shut-off valve;
   (b) male NGT (National Gas Taper) container connection of 19.05 mm
       19.05 mm;
   (c) male NPT (National Pipe Taper) service connection of 9.525 mm;
 but NOT including automotive cylinder valves or valves incorporating
 a solenoid shut-off

VALVES, GLOBE, manually operated, having ALL of the following:
   (a) bore sizes of between 50 mm and 200 mm;
   (b) cast iron construction;
   (c) flow measure;
   (d) variable calibration pre-setting;
   (e) pre-selected flow rate at each setting

VALVES, VACUUM, SOLENOID, having ALL of the following:
   (a) voltage 12 V DC;
   (b) power 4 W;
   (c) endurance pressure NOT exceeding 740 mm Hg/min;
   (d) operating voltage from a minimum of 8.5 V to a maximum of
       14.8 V;
   (e) air passage NOT exceeding 4 L/min

VALVES, BUTTERFLY, double offset, having ALL of the following:
   (a) carbon steel body and disc;
   (b) bore size within the range 50 mm to 700 mm (both inclusive)
   (c) bidirectional sealing;
   (d) wafer OR lugged flange mounting;
   (e) rated to ANSI B 16.5 class 300

CHRISTMAS TREES, HORIZONTAL, SUBSEA WELL

VALVES, DRAIN, LIQUIFIED PETROLEUM GAS, manually operated,
 internal excess flow

VALVES, FILLER, LIQUIFIED PETROLEUM GAS, manually operated, internal
 back check

BATH AND BASIN WASTE ASSEMBLIES, having ALL of the following:
  (a) pop-up waste plug;
  (b) overflow waste pipe;
  (c) waste outlet connection;
  (d) remote pop-up plug control knob

VALVES, DIRECTIONAL CONTROL, sliding spool, hydraulic remote
 control, having interface mounting surfaces compatible with ANY
 of the following standards:
   (a) CETOP 5, RP35H, 7, 8;
   (b) NG4, 5

VALVES, LOCK MANDREL AND SUBSURFACE FLOW CONTROL EQUALISING, OIL AND
 GAS WELL, having a pressure rating of NOT less than
 34 450 kPa (5 000 psi)

ADAPTORS, RESTRICTION, FILLING AND UNLOADING, including an integral
 back check

VALVES, TUBELESS TYRE, AIR WATER, having ALL of the following:
   (a) core housing;
   (b) core housing thread size of 9.50 mm (32 UNEF - 2A);
   (c) TR nos. 618A, 621A, 622A or 623A

VALVES, spool, manually operated, multi-directional flow and dual
 supply, having an operating pressure of 2 bar to 10 bar (both
 inclusive)

VALVES, plug, having a nominal bore size 15 mm to 150 mm (both
 inclusive) incorporating BOTH of the following:
   (a) 2 and 3 way design;
   (b) non-lubricated tapered plug

VALVES, tubeless tyre for passenger carrying motor vehicles, type
 Nos. TR412, TR413, TR414, TR414L, TR415, TR418, TR420, TR423, TR425,
 TR438

GATE VALVES, carbon steel, stainless steel or high alloy steel.
 having ALL of the following:
   (a) manufactured in accordance with ANY of the following
         (i) BS 5352;
        (ii) BS 1873;
       (iii) BS 1414;
        (iv) API 600;
         (v) API 602
   (b) pressure rated to ANY of the following:
         (i) ASME/ANSI 150;
        (ii) ASME/ANSI 300;
       (iii) ASME/ANSI 600;
        (iv) ASME/ANSI 800;
         (v) ASME/ANSI 900;
        (vi) ASME/ANSI 1500;
       (vii) ASME/ANSI 2500;
      (viii) ASME/ANSI 4500
   (c) pressure temperature rating to ANSI B16.34;
   (d) screwed, socketweld, flanged or buttweld end connections;
   (e) in respect of flange mounted valves, having BOTH the
       following:
          (i) face to face dimensions to ASME/ANSI B16.10;
         (ii) flange end dimension and gasket face finish to
              ASME/ANSI B16.5
   (f) in respect of buttweld end connection valves, having end to
       end dimensions to ASME/ANSI B16.10;
   (g) hydrostatic and air test pressure to API 598;
   (h) wall thickness to API 600, API 602 or API 603

VALVES, pneumatic, three way flow through, pneumatically operated
 pressure regulating, having a working pressure NOT exceeding 350 bar

MIXERS, CLOSING, TAP AND/OR SHOWER HEAD, SINGLE LEVER,
 conforming to AS3718, having ALL of the following:
   (a) hydraulic valve;
   (b) pressure dampening brass piston;
   (c) ceramic sealing control discs;
   (d) pressure operated bottom seals;
   (e) filter screen;
   (f) preset water flow and temperature control

VALVES, INTERNAL, LIQUIFIED PETROLEUM GAS AND ANHYDROUS AMMONIA,
 incorporating an excess flow valve, operated by ANY of the
 following means:
   (a) manually;
   (b) air actuation; OR
   (c) melting of a fusable link

VALVES, DIRECTIONAL CONTROL, piloted, pressure actuated, spring
 return, having BOTH of the following:
   (a) thread diameter of 3.175 mm to 12.7 mm (both inclusive);
   (b) operating pressure of 2 bar to 10 bar (both inclusive)

VALVES, single seat, stainless steel, complying with ALL the
 following:
   (a) sanitary construction;
   (b) clean in place (CIP) operation;
   (c) capable of separating the flow of two different fluid systems;
   (d) port sizes 25 mm to 153 mm

VALVES, NEEDLE, panel mountable, NOT exceeding 27 mm, integral
 tube end connections, pressure rated to exceed 3 000 kPa

VALVES, GAS CYLINDER

VALVES, AIR BRAKE, foot operated, graduating directional control

VALVE POSITIONERS, pneumatic or electro-pneumatic

VALVES, diaphragm, chemical resistant body of fibreglass reinforced
 nylon

VALVES, BUTTERFLY, having ALL of the following:
   (a) cast iron construction;
   (b) manual OR actuator operation;
   (c) bore size greater than 500 mm;
   (d) flange pressure rating to ANY of the following:
          (i) ANSI 125;
         (ii) ANSI 150;
   (e) speed controller

VALVES, INVERSION, AIR BRAKE

VALVES, CYLINDER, LPG, VAPOUR SERVICE, manual shut off,
 incorporating a relief valve

VALVES, BALL, forged titanium

VALVES, BRASS, three-way rotating ball, "L" or "T" ported, having
 ALL of the following:
   (a) thread sizes from 15 mm (1/2" BSP) to 50 mm (2" BSP) (both
       inclusive);
   (b) Australian Gas Association approval AG201;
   (c) spring-loaded handle with 360 degrees ball rotation;
   (d) 3 connections fully sealed with 4 self-adjusting ball seals;
   (e) pressure rating 2 500 kPa

VALVES, COMBINED CHECK AND FOOT, positive pressure and vacuum,
 having ALL of the following:
   (a) thread connection sizes from 8 mm (1/4" BSP) to 100 mm
       (4" BSP) (both inclusive);
   (b) multi-positional mounting;
   (c) spring loaded jumper valve;
   (d) filter provision

VALVES, FLOW CONTROL, being EITHER of the following:
   (a) hydraulic circuit flow control valves, having ALL of the
       following:
         (i) manual OR pressure operation;
        (ii) 2 ports;
       (iii) threaded connection, manifold mount OR cartridge,
             whether OR not incorporating a check valve;
        (iv) steel or stainless steel construction;
         (v) maximum operating pressure NOT less than 34.5 MPa; OR
   (b) hydraulic stop OR throttle stop, balanced piston, having
       ALL of the following:
         (i) steel OR iron and steel construction;
        (ii) thread, flange OR gasket mounted, whether OR not
             incorporating a check valve;
       (iii) maximum operating pressure NOT less than 21 MPa

PRESSURE REGULATORS, having ALL of the following:
   (a) port connections with OD thread sizes ranging from 3 mm to
       51 mm (both inclusive);
   (b) incorporating a self bleed feature for relieving pressure
       downstream from the regulator;
   (c) airline pressure rating NOT exceeding 2 MPa

COUPLINGS, VALVE, steel, quick release by retracting the sleeve,
 with a minimum working pressure of 210 bar and self sealing valves
 on disconnect

VALVES, BALL, full bore, trunnion mounted, to API 6D, having ALL of
 the following:
   (a) pressure rating to ANSI 1 500;
   (b) flanged end connections to ASME B 16.5 or ASME B 16.34;
   (c) manual gearbox actuator;
   (d) bore greater than 500 mm

VALVES, PNEUMATIC CONTROL, AIR SUSPENSION BELLOW

BALL VALVES,  polyethylene OR polyvinylchloride, of a size NOT less
 than 2 in (5 cm)

VALVES, PNEUMATIC, having ALL of the following:
   (a) stainless steel lapped spool and floating sleeve valve
       mechanism with no dynamic rubber seals;
   (b) air bearing spool requiring no pre-lubrication or air line
       lubrication;
   (c) equal diameter cross holes in flow galleries of sleeve
       assembly;
   (d) self cleaning capability through shearing action of spool
       edges against the holes in the sleeve;
   (e) balanced spool construction permitting BOTH of the following:
         (i) simultaneously a vacuum and pressure to 2067 kPa; and
        (ii) independent of pilot pressure, full back pressure at any
             port and no blow-by to exhaust during spool shift

VALVES, GLOBE, complying with BOTH of the following:
   (a) manufactured in accordance with ANY of the following
       standards:
            (i) BS 1560;
           (ii) BS 1873;
          (iii) BS 5152;
           (iv) BS 5154;
            (v) BS 5352;
           (vi) ANSI B16.34;
          (vii) API 597;
         (viii) API 598;
           (ix) API 6D;
            (x) API 600;
           (xi) API 602;
   (b) pressure rated to ANY of the following:
            (i) ANSI 150;
           (ii) ANSI 300;
          (iii) ANSI 600;
           (iv) ANSI 800;
            (v) ANSI 900;
           (vi) ANSI 1500;
          (vii) ANSI 2500;
         (viii) ANSI 4500

VALVE, BRASS BALL, 1/4 turn, 3 way diverting having ALL of the
 following:
   (a) "L" port configuration;
   (b) Australian Gas Association approval;
   (c) sizes 1/4 inch BSP to 2 inch BSP inclusive, (nominal 8 mm to
       50 mm);
   (d) die-cast aluminium handle

VALVES, DRUM, stainless steel, being a dry disconnect valve with
 provision for drum suction tube, with OR without the tube

VALVES, oil hydraulic, load independent, proportional directional

VALVES, KEG SPEAR, with syphon tube

VALVES, motorcycle tyre, valve hole size 8.3 mm

VALVES, 1/4 turn ball, having ALL of the following:
   (a) 8 mm (1/4" BSP) to 100 mm (4" BSP) sizes inclusive;
   (b) treated with trichloroethylene;
   (c) individually sealed in plastic

VALVES, hydraulic, pilot assisted overcentre, providing cavitation
 free controlled load lowering, pressure relief function and load
 holding, 350 bar maximum pressure setting

VALVES, GLOBE, manually operated, stainless steel, having
 ALL of the following:
   (a) capable of operating within the temperature range of -196
      degrees C to 816 degrees C;
   (b) manufactured in accordance with one of the following
       standards:
          (i) ANSI B2.1;
         (ii) ANSI B16.10;
        (iii) ANSI B16.34;
         (iv) API 6D;
          (v) API 597;
         (vi) API 598;
        (vii) API 600
   (c) having a pressure rating of one of the following classes:
          (i) ANSI 150;
         (ii) ANSI 300;
        (iii) ANSI 600;
         (iv) ANSI 900;
          (v) ANSI 1500;
         (vi) ANSI 2500;
        (vii) ANSI 4500

VALVES, AEROSOL, having a laminated bag attached

CHOKE VALVES, adjustable, for control of oil and natural gas flow in
 producing wells

COUPLER VALVES (DISPENSING HEADS), HERMETICALLY SEALED CONTAINER,
 stainless steel

VALVES, automatic air or gas release, 12 mm to 25 mm nominal
 diameter, having ALL of the following:
   (a) maximum operating pressure of 1 200 kPa;
   (b) polypropylene body;
   (c) release rate up to 50 cubic metres per hour;
   (d) mechanism incorporating:
         (i) non-metallic flexible rolling seal with non-metallic
             attached stem; and
        (ii) float of formed polypropylene

VALVES, TUBELESS TYRE, brass, rim hole sizes 9.7 mm to 16 mm

VALVES, TUBELESS TYRE, having ANY of the following:
   (a) valve core with thread diameter NOT less than VG.8;
   (b) core housing thread diameter NOT less than 12.70 mm (32 UNF);
   (c) able to fit tubeless spud threads

NOZZLES, stainless steel

VALVES, FLOW CONTROL, pressure compensated, two port, inlet pressure
 rating 12 300 kPa

VALVES, MANIFOLD, stainless steel, block construction, pressure
 rating of 41 MPa at 38 degrees Celsius

NOZZLES, LIQUID FUEL, having a built-in check valve and threaded
 inlets, with an external diameter of 20 mm, 25 mm OR 50 mm

VALVES, emergency relay, air brake

COUPLINGS, VALVE, HYDRAULIC, steel, having retracting sleeve
 quick release, in sizes greater than 25.4 mm with working pressures
 greater than 100 bar

VALVES, solenoid, hydraulic control, having ALL of the following:
   (a) maximum flow rate of 146.2 litres per minute;
   (b) operating pressure of 200 kg/sq cm

VALVES, solenoid, hydraulic directional control, 20 Mpa or greater
 but NOT including valves having a mounting interface conforming with
 ANY of the following:
     (a) DIN 24340-A6;
     (b) ISO 4401-AB-03-4-A;
     (c) CETOP R35H 4.2-4-03;
     (d) NFPA DO3;
     (e) CETOP 3;
     (f) NG 6

VALVES, FINE METERING, having ALL of the following:
   (a) orifice diameter NOT exceeding 1.5 mm;
   (b) stem taper NOT exceeding 3 degrees;
   (c) requiring from 8 turns to 12 turns (both inclusive) to open;
   (d) dead space NOT exceeding 460 cu mm;
   (e) working pressure NOT exceeding 14 MPa

VALVES, butterfly, triple offset, metal seated, of stainless steel
 or carbon steel construction, having ALL of the following:
   (a) wafer, lugged or double flange mounting;
   (b) nominal bore size of 76.2 mm or greater;
   (c) pressure rating to ANY of the following classes:
       (i)   ANSI 150;
       (ii)  ANSI 300;
       (iii) ANSI 600;
   (d) capable of manual or actuator operation;
   (e) laminated metal or solid metal seal

VALVES, SOLENOID DIRECTIONAL CONTROL, with explosion proof coils
 OR intrinsically safe coils

MULTI VALVE ASSEMBLIES, LPG, having a tank connection size of
 19 mm OR greater, containing ANY three of the following:
   (a) fixed liquid level gauge;
   (b) male ACME fill valve;
   (c) male ACME vapour equalising valve complete with excess flow
       protection;
   (d) service valve consisting of a shut-off valve and female POL
       connection;
   (e) pressure relief valve;
   (f) plugged pressure gauge port

METERING VALVE ASSEMBLIES, AEROSOL, 11 - 14 mg OR 23 - 28 mg

VALVES, POSITIVE SEAL OBTURATING ELEMENT, direct solenoid or
 externally controlled

VALVES, stick on, automotive tyre

VALVES, PIPE SIDE, 3 port, 2 way, regulating, abrasive resistant,
 having an axially movable unitary plunger

VALVES, hydraulic control, having ALL of the following:
   (a) max flow rate from 130 litres per minute to 400 litres per
       minute (both inclusive);
   (b) maximum operating pressure from 300 kg/sq cm to 320 kg/sq cm
       (both inclusive)

SLIDING GATE MACHINES, STEEL LADLE

FILTERS, COMPRESSED AIRLINES, having ALL of the following:
   (a) regulator;
   (b) port connections with OD thread sizes ranging from 3 mm to
       51 mm (both inclusive);
   (c) airline pressure rating NOT exceeding 2 MPa

COUPLINGS, VALVE, HYDRAULIC LINE, stainless steel OR brass, coupled
 pressure rating of 3 400 kPa OR greater, being EITHER of the
 following:
   (a) bodies, push connect, incorporating slide spring loaded
       sleeves;
   (b) stems, push connect

VALVES, COAXIAL TUBE ELEMENT, externally or direct solenoid
 activated

VALVES, BALL, two-way, hydraulic fluid control system, having ALL
 of the following:
   (a) port sizes NOT greater than 50 mm;
   (b) bore sizes NOT less than 93% of port sizes;
   (c) working pressure of 31.5 MPa or greater at 100 degrees C;
   (d) manual actuation;
   (e) NOT of the fire-safe and/or anti-static design

CONTROL SYSTEM, COMPRESSOR AIR INTAKE, comprising ALL of the
 following:
   (a) intake controller with inlet valve;
   (b) actuating piston;
   (c) pressure lowering non-return valve;
   (d) with or without solenoid and pressure switch

VALVES, ball, brass, having ALL of the following:
  (a) 1/4 on/off turn operation;
  (b) 1/4" BSP (6mm) to 4" BSP (100mm) (both inclusive);
  (c) manufactured from DR (dezincification resistant) brass;
  (d) with "Watermark" certification

VALVES, diesel engine air starter, being pilot operated control
 valves

AIRCRAFT REFUELLING EQUIPMENT, being ANY of the following:
   (a) adaptor, aircraft OR ground;
   (b) coupler, aircraft OR ground;
   (c) valve, hydrant pit;
   (d) nozzle, hose

DAMPERS, PULSATION, in line

VALVES, sleeve actuated AND/OR regulated, axial flow, pilot 
valve controlled

TAPS, BENCH TOP, including ALL of the following:
  (a) tap;
  (b) spout;
  (c) water filter connector, 
with OR without LED (light-emitting diode) filter change 
indicator

VALVES, DIAPHRAGM, having BOTH of the following:
  (a) nominal size (DN) NOT greater than 150 mm;
  (b) manual AND/OR motorised AND/OR pneumatic actuation, 
with OR without ANY of the of the following:
    (i) position OR flow indicators;
   (ii) controllers incorporating built-in solenoid valves

VALVES, SLURRY, linear AND rotational actuation mechanism, being 
ANY of the following:
  (a) angle valves;
  (b) bayonet valves;
  (c) three-way valves;
  (d) remote actuated valves

EXPLOSION ISOLATION VALVES, poppet type having a centering 
spring mechanism, including ALL of the following:
  (a) nominal sizes (DN) NOT less than 100 and NOT greater than
      600;
  (b) elastomer gaskets;
  (c) o-ring seals

VALVES, butterfly, triple eccentric, metal seated, having a 
single acting pneumatic actuator

VALVES, WATER SOFTENER SYSTEM, with OR without timer AND/OR 
controller, having a continuous flow rate NOT greater than 
30.0 m/3 per hour

VALVES, PRESSURE INDEPENDENT CONTROL, including ALL of the 
following:
  (a) integrated pressure differential controller;
  (b) volumetric flow NOT less than 0.03 m3/h and NOT greater 
      than 195 m3/h;
  (c) maximum allowable differential pressure NOT less than 600 
      kPa; 
  (d) radial adjustment of maximum flow setting;
  (e) two integrated pressure testing ports; 
  (f) valve stroke between NOT less than 2.5 mm and NOT greater
      than 45 mm

DISPENSERS, BEVERAGE, with OR without detachable front panel, 
including BOTH of the following:
  (a) body AND/OR stand;
  (b) NOT less than two taps OR valves, having EITHER of  
      the following:
        (i) buttons;
       (ii) levers

VALVES, ISOLATION OR SHUT OFF, BLAST FURNACE, electrically 
actuated, having a weight exceeding 1 300 kg

VALVES, GLOBE AND/OR ANGLE SEAT, having ALL of the following:
  (a) PTFE (polytetrafluoroethylene) spring loaded packing stem;
  (b) stainless steel body;
  (c) nominal size NOT greater than (Diameter Nominal) DN 100;
  (d) motorised AND/OR pneumatic actuator,
with OR without ANY of the following:
           (i) position OR flow indicators, whether OR not
               incorporating built-in solenoid valves;
          (ii) position OR flow OR temperature OR pressure
               controllers, incorporating built-in solenoid
               valves;
         (iii) manifold

WINE EXTRACTING MACHINES, whether OR not in sets, including BOTH 
of the following:
  (a) cork piercing needles;
  (b) pressurised trigger,
with OR without ANY of the following:
          (i) argon gas capsule;
         (ii) pedestal base;
        (iii) carry case

VALVES, GAS CYLINDER, flow control, having ALL of the following:
  (a) flow AND/OR pressure adjustment;
  (b) integrated pressure regulator;
  (c) shut off valve;
  (d) safety relief valve,
with OR without guards OR gauges

MONOLINK TERMINAL UNIT, brass alloy, having ALL of the following:
  (a) operating temperature NOT less than minus 10 degrees  
      Celsius and NOT greater than 120 degrees Celsius;
  (b) male BSP union thread port having a DN size NOT less 
      than 0.5 inch and NOT greater than 1.5 inch;
  (c) other side female BSP thread having a DN size NOT 
      less than 0.5 inch and NOT greater than 1.5 inch,
with OR without one OR more of the following:
           (i) valve strainers;
          (ii) ball valves;
         (iii) balancing valves;
          (iv) electric actuators

IN-LINE TEE SUBSEA PIPELINE ASSEMBLIES, including ALL of the 
following:
  (a) piping module, including ALL of the following: 
         (i) pipes;
        (ii) pipe elbows;
       (iii) pipe tees;
        (iv) pipe connectors;
         (v) pressure caps;
        (vi) pipe hub connectors;
       (vii) ball valves;
      (viii) steel support frame,
  (b) mud mats AND/OR steel foundation arms;
  (c) anodes

SYSTEM, SUBSEA PIPELINE END TERMINATION, consisting of ALL of 
the following:
  (a) piping;
  (b) pipe elbows;
  (c) pipe tees;
  (d) pipe bends;
  (e) pressure caps;
  (f) pipe connectors;
  (g) ball valves;
  (h) anodes;
  (i) steel support frame;
with OR without EITHER of the following:
         (i) mud mats;
        (ii) steel foundation arms

VALVES, SHUT OFF, TWO LEVER, including hydraulic cylinder, 
having ALL of the following:
  (a) nominal diameter NOT greater than 4000 mm;
  (b) pressure rating NOT greater than PN10;
  (c) operating temperature NOT greater than 600 degrees Celsius

GATE VALVES, SURFACE SAFETY, OIL AND/OR GAS WELL TESTING, 
hydraulically actuated, remotely operated, with OR without 
lifting frame AND/OR crossover connections, including ALL of the 
following:
  (a) double metal to metal seals;
  (b) working pressure NOT less than 32 MPa and NOT greater than 
      105 MPa;
  (c) bore diameter NOT less than 5 centimetres and NOT greater 
      than 14 centimetres

MID-CONNECTION MODULE, SUBSEA, including of ALL of the following:
  (a) piping unit including ALL of the following: 
          (i) subsea ball valves;
         (ii) piping;
        (iii) tubing;
         (iv) tees;
          (v) bends;
         (vi) elbows;        
        (vii) pressure caps;
       (viii) connectors;
         (ix) flanges
          (x) temperature sensor,
  (b) housing frame;
  (c) mud mats;
  (d) anodes

FLOW CONTROL VALVES, balancing, cast iron construction, having 
ALL of the following:
  (a) pressure rating NOT less than 1 600 KPa;
  (b) valve body size NOT less than 50 mm and NOT greater 
      than 300 mm;
  (c) pressure differential measurement test points

BALL VALVES, having ALL of the following:
  (a) flanged;
  (b) ductile iron body;
  (c) full bore diameter NOT less than 25 mm and NOT greater
      than 200 mm

BALL VALVES, having ALL of the following:
  (a) brass alloy body AND aperture;
  (b) brass square cap;
  (c) inlet AND outlet diameter NOT less than 15 mm and NOT 
      greater than 80 mm

MANIFOLDS, OIL AND/OR GAS, skid mounted, including ALL of the 
following:
  (a) maximum working pressure NOT less than 9 000 KPa;
  (b) NOT less than 2 ball valves;
  (c) gasket;
  (d) concentric reducer;
  (e) flange;
  (f) total length of pipes NOT greater than 10 m;
  (g) skid

VALVES, PRESSURE CONTAINING, OIL AND/OR GAS WELL, hydraulic, 
surface operated, including ALL of the following:
  (a) valve centraliser;
  (b) piston;
  (c) ball valve;
  (d) fluid control hoses

VALVES, TRAILER ELECTRONIC BRAKING SYSTEM, being EITHER of the 
following:
  (a) master valves;
  (b) remote valves

MANIFOLDS, SELF-CLEANING SYSTEM, with OR without piping, 
including BOTH of the following:
  (a) NOT less than five double seated valves;
  (b) pneumatic actuators

FLOW CONTROL VALVES, with OR without actuator, having ALL of the 
following:
(a) manual flow pre-set with indicator; 
(b) pressure rating of PN25; 
(c) flow coefficient exceeding 1.6 kV fully opened; 
(d) flow verification test points;
(e) operating temperature range NOT less than -10C and NOT 
    greater than 120C

CIRCULATION TANK UNITS, including ALL of the following:
  (a) pumps;
  (b) tank outlet fittings;
  (c) valves;
  (d) control heads;
  (e) level probes;
  (f) flow meter; 
  (g) temperature sensors;
  (h) base frames;
  (i) pipes

VALVES, URINAL FLUSH, with OR without ANY of the following:
  (a) control unit;
  (b) power supply;
  (c) extension cable

VALVES, SOLENOID, with OR without manifold, complying with 
WaterMark Technical Specification WMTS-030:2016, having an 
orifice diameter NOT greater than 50 mm

BUTTERFLY VALVES, flanged, having ALL of the following:
  (a) nominal diameter NOT less than 2 000 mm;
  (b) working pressure NOT less than 10 bar;
  (c) hydraulic actuator;
  (d) weld deposited body seat

BALL VALVES AND/OR BIBCOCKS, lever OR T handle, having ALL of 
the following:
  (a) nickel OR chrome plated brass bodies;
  (b) working temperature NOT less than minus 20 degrees C and 
      NOT greater than 150 degrees C;
  (c) inlet AND outlet diameter NOT less than 3 mm and not 
      greater than 105 mm

VALVES, BLAST FURNACE

FLUE GAS ANGLE PLUG VALVES, refractory lined, with OR without 
manual OR electric actuator, having BOTH of the following:
  (a) inlet AND outlet inside diameter NOT less than 500 mm;
  (b) operating temperature NOT less than 300 degrees C

REMOTE DUAL-VALVE TOOLS, DOWNHOLE RESERVOIR TESTING, whether OR 
not assembled, with OR without wireless telemetry, having ALL of 
the following:
  (a) circulating valves;
  (b) test valves;
  (c) atmospheric chambers;
  (d) hydrostatic chambers;
  (e) pressure sensors;
  (f) electronics;
  (g) batteries

VALVES, REFRIGERATION AND/OR AIR CONDITIONING, having EITHER of 
the following:
  (a) VALVE STATION ASSEMBLIES, having BOTH of the following:
         (i) valve housing;
        (ii) one or more of ANY of the following:
                  (1) shut-off valve module;
                  (2) manual regulating valve module;
                  (3) strainer module;
                  (4) solenoid valve module;
                  (5) electronic expansion valve module;
                  (6) manual opening module;
                  (7) check valve module;
                  (8) stop AND check valve module;
                  (9) pilot operated servo valve module;
                 (10) defrost drain module;
                 (11) motor operated valve module;
                 (12) external welding connection module;
                 (13) blind cover;
                 (14) sight glass;
                 (15) temperature pressure sensor;
                 (16) pressure gauge;
                 (17) drain OR bypass side exit,
  (b) VALVE MODULES, being ANY of the following:
          (i) shut-off valve module;
         (ii) manual regulating valve module;
        (iii) solenoid valve module;
         (iv) electronic expansion valve module;
          (v) manual opening module;
         (vi) stop AND check valve module;
        (vii) pilot operated servo valve module

TAPPING VALVES, having ALL of the following:
  (a) outer body NOT less than 50% fibreglass reinforced 
      polyamide;
  (b) stainless steel saddle clamp; 
  (c) brass drill;
  (d) integrated isolation valve

VALVES, BALL, austenitic stainless steel body, including ALL of 
the following:
  (a) steel carbon content NOT greater than 0.030%;
  (b) steel nickel content NOT less than 8% and NOT greater
      than 14%;
  (c) opening AND closing operation NOT greater than 1/4 turn; 
  (d) manually OR pneumatically actuated;
  (e) inlet AND outlet diameter NOT greater than 153 mm

VALVES, carbon steel OR alloy steel OR stainless steel OR nickel 
alloys OR titanium, screwed OR flanged end connection, being ANY 
of the following:  
  (a) ram bottom outlet valves;
  (b) piston bottom outlet valves

PNEUMATIC DAMPER, WELDING FUME, AIR AND DUST RETICULATION SYSTEM

WATER DOSER MIXERS, electronic

VALVES, cylinder, regulating, having ALL of the following:
  (a) internal pressure regulator;
  (b) outlet flow NOT greater than 30 l/min;
  (c) operating pressure NOT greater than 30 MPA

ROTARY FILTER VALVES, POLLUTANT AND/OR WOOD CHIP PROCESSING

SLIDE VALVES, CATALYST, with OR without actuators, having BOTH 
of the following:
  (a) single OR double disc;
  (b) refractory lining

CHOKE VALVE ASSEMBLIES, SUBSEA OIL AND/OR GAS WELL, whether OR 
not assembled, including ALL of the following:
  (a) valve;
  (b) actuator;
  (c) connector;
  (d) seals;
  (e) guide pins AND/OR aligning device,
with OR without EITHER of the following:
            (i) trim positioner;
           (ii) lifting mandrel

SHUNT TUBE ISOLATION VALVES, DOWNHOLE, OIL AND/OR GAS WELL, 
whether OR not assembled, having a differential pressure NOT 
less than 3 000 PSI

VALVES, STOP AND/OR SHUT-OFF, with OR without mounting clips, 
having ALL of the following:
  (a) acetal body;
  (b) push-fit connections;
  (c) tube outer diameter NOT exceeding 15 mm

VALVES, REFRIGERATION, shut-off AND/OR regulating, having ALL of 
the following:
  (a) stainless steel housing;
  (b) nominal diameter NOT less than 15 mm and NOT greater than 
      125 mm;
  (c) temperature range NOT less than minus 60 degrees Celsius
      and NOT greater than plus 150 degrees Celsius;
  (d) operating pressure NOT greater than 52 bar,
with OR without hand-wheel OR cap

BALL VALVES, flanged wafer end, having BOTH of the following:
  (a) DN NOT less than 15 mm and NOT greater than 200 mm;
  (b) full bore

VALVES, GLOBE AND/OR GATE, without OR with actuator, complying 
with ANY one OR more of the following standards:
  (a) British Standard 1414 (BS1414);
  (b) British Standard 1873 (BS1873);
  (c) British Standard 5152 (BS5152);
  (d) British Standard 5154 (BS5154);  
  (e) International Standard 15761 (ISO 15761);         
  (f) International Standard 10434 (ISO 10434);
  (g) American Society of Mechanical Engineers Standard B16.34 
      (ASME B16.34);
  (h) American Society of Mechanical Engineers Standard B31.3 
      (ASME B31.3);
  (i) American Petroleum Institute Standard 6D (API 6D);
  (j) American Petroleum Institute Standard 600 (API 600);
  (k) American Petroleum Institute Standard 602 (API 602);
  (l) American Petroleum Institute Standard 603 (API 603);
  (m) American Petroleum Institute Standard 623 (API 623);
  (n) International Association of Oil and Gas Producers 
      Standard S-611 (IOGP S-611);
  (o) British Standard 13789 (BS13789);
  (p) British Standard 12288 (BS12288)

HYDROGEN COMPRESSOR STATION, programmable logic controlled, 
whether OR not containerised, including ALL the following: 
  (a) compressors; 
  (b) hydraulic pumps AND motors; 
  (c) pressure control management; 
  (d) valves;  
  (e) gas dispensers; 
  (f) dispenser connection sensors AND controls;
  (g) breakaway couplings;
  (h) price AND volume controls,  
with OR without ANY of the following:
         (i) cooling unit;
        (ii) gas storage containers;
       (iii) ventilation controller;
        (iv) phase separator AND/OR filter;
         (v) refrigeration unit;
        (vi) heat exchanger;
       (vii) chiller;
      (viii) instrument air supply;
        (ix) cabling;
         (x) interconnecting piping spool and couplings;
        (xi)`price AND/OR volume AND/OR total cost display; 
       (xii) assembly tools being ANY of the following:
               (1) tube bender;
               (2) coning tools; 
               (3) threading tools AND/OR tube vises

HYDRAULIC BLOCK, having ALL of the following:
  (a) NOT less than 4 functions and NOT greater than 20 
      functions; 
  (b) weight NOT less than 8 kg; 
  (c) operating pressure NOT greater than 350 bar;
  (d) maximum power consumption exceeding 70 mA;
  (e) pressure limitation valve

AIR REGULATORS, PAINTBALL MARKER PRESSURE BOTTLE, with OR 
without gauge

BASE FITTING VALVES, TAP OR SHOWER MIXER, including NOT less 
than two of the following: 
  (a) o-ring;
  (b) plug;
  (c) sealing foil;
  (d) extension

PRESSURE INDEPENDENT BALANCING AND CONTROL VALVES,  including 
ALL of the following:
  (a) brass AND/OR iron body;
  (b) weight NOT less than 0.3 kg;
  (c) differential pressure cone AND/OR controller;
  (d) flow rate NOT greater than 407 500 litres per hour; 
  (e) differential pressure NOT less than 15 kPa and 
      NOT greater than 601 kPa;
  (f) handle AND/OR actuator,
with OR without test plugs AND/OR points

VALVES, BALL AND/OR BUTTERFLY, without OR with actuator, 
complying with ANY one OR more of the following standards:
  (a) American Petroleum Institute Standard 6D (API 6D);
  (b) International Standard 14313 (ISO 14313);
  (c) International Standard 17292 (ISO 17292);
  (d) American Petroleum Institute Standard 609 Category A 
      (API 609);
  (e) American Petroleum Institute Standard 609 Category B 
      (API 609);
  (f) British Standard 5155 (BS5155);
  (g) British Standard 593 (BS EN 593)

SLIDING GATE MACHINES, STEEL LADLE

SURFACE CHRISTMAS TREES, with OR without ANY of the following:
  (a) connectors being assembled OR unassembled;
  (b) actuators

VALVES, AEROSOL, having a laminated bag attached

BUTTERFLY VALVES, bi-directional, wafer OR lug, 
having a diameter NOT less than 40 mm and NOT greater than 400 
mm, having ANY of the following:
  (a) hand operated lever;
  (b) gearbox OR pneumatic AND/OR electric actuator control

BATHROOM FITTINGS, being ANY of the following:
  (a) isolation valves having flow meters AND pressure sensors;
  (b) shower mixers having ALL of the following:
          (i) electronic temperature control;
         (ii) network connectivity;
        (iii) LCD touchscreen;
         (iv) solenoid valve,
  (c) basin taps having ALL of the following:
          (i) infra-red sensor;
         (ii) network connectivity;
        (iii) control box;
         (iv) power plug AND/OR connector

VALVES, FLY ASH DIFFUSER, having both of the following:
 (a) inlet diameter NOT less than 203 mm;
 (b) outlet diameter NOT less than 152 mm

VALVES, assembled, flow control AND hydronic balance, having 
ALL of the following:
  (a) pressure independent control valves;
  (b) shut-off valves;
  (c) strainer valves with integrated drain function;
  (d) handle fittings AND measuring plug
with OR without actuator

VALVES, BUTTERFLY, having ALL of the following:
  (a) internal diameter NOT less than 280 mm and NOT
      greater than 3 100 mm;
  (b) pressure rated NOT less than 9 bar; 
  (c) flange mounted;
  (d) ductile cast iron body;
  (e) double offset design;
  (f) bi-directional sealing;
  (g) gearbox having hand-wheel OR electric OR hydraulic
      actuation

VALVES, TRIP AND THROTTLE, having ALL of the following:
  (a) handwheel; 
  (b) test facility;
  (c) limit switch;
  (d) steam strainer;
  (e) support assembly

ROTARY VALVES, MATERIAL HANDLING, having ALL of the following:
  (a) direct drive through coupling OR flat gear drive;
  (b) throughput capacity NOT exceeding 9 200 m3/hr;
  (c) flame propagation AND explosion pressure resistance module;
  (d) gear motor;
  (e) pulse generator ring;
  (f) speed switch,
with OR without ANY of the following:
          (i) casing knife;
         (ii) rotor with double wearing strip;
        (iii) frame

IN-LINE TEE SUBSEA ASSEMBLY, including ALL of the following:
  (a) piping;
  (b) elbows;
  (c) tees;
  (d) bends;
  (e) connectors;
  (f) valves;
  (g) frame;
  (h) caps,
with OR without the following:
           (i) actuator;
          (ii) flanges;
         (iii) mud mats;
          (iv) foundation arms;
           (v) anode;
          (vi) stab assembly including receptacle;
         (vii) hub;
        (viii) yoke;
          (ix) padeye;
           (x) sliding Shoe;
          (xi) guide

ASSEMBLIES, SUBSEA FLOWLINE END TERMINATION, whether OR not 
assembled, having ALL of the following:
  (a) piping;
  (b) elbows;
  (c) tees;
  (d) bends;
  (e) caps;
  (f) connectors;
  (g) valves;
  (h) frame,
with OR without ANY of the following:
           (i) actuator;
          (ii) flanges;
         (iii) mud mats;
          (iv) foundation arms;
           (v) anode;
          (vi) stab assemblies having BOTH of the following:
                     (1) hot stab;
                     (2) receptacle,
         (vii) hub;
        (viii) yoke;
          (ix) pad eye;
           (x) sliding shoe;
          (xi) guide

VALVES, INJECTION METERING, SUBSEA, with OR without ANY of the 
following:
  (a) retrievable insert assemblies including inlet AND/OR 
      outlet couplers;
  (b) actuator;
  (c) cathodes;
  (d) receptacle

PARTS, DEFIBRATOR AND/OR REFINER, being one OR both of the 
following:
  (a) blow valves;
  (b) diverter valves

CUT-OFF GATE VALVES, DRY PULVERISED MATERIAL, incorporating a 
stuffing box seal with wool packing AND felt ring

VALVES, FLOW CONTROL GATE, DRY PULVERISED BULK MATERIAL, being 
manually OR motor OR pneumatically driven, with OR without ANY 
one OR more of the following:
  (a) aeration cushion;
  (b) angular position encoder;
  (c) electro-pneumatic position control unit;
  (d) manual emergency hand lever;
  (e) limit switch;
  (f) roller

CABINETS, ICE AND/OR WATER DISPENSING

INTERVENTION AND WORKOVER CONTROL MODULE, SUBSEA OIL AND/OR 
GAS WELL, whether OR not assembled, including ALL of the 
following:
  (a) emergency disconnect package; 
  (b) lower riser package; 
  (c) flowhead valve,
with OR without ANY of the following:
           (i) test AND/OR lift caps OR plugs OR flanges; 
          (ii) clamps;
         (iii) joints AND/OR connectors AND/OR adapters; 
          (iv) valves;
           (v) swivel; 
          (vi) piping AND/OR hoses AND/OR jumpers AND/OR flying 
               leads; 
         (vii) reelers; 
        (viii) umbilicals;
          (ix) umbilical sheaves; 
           (x) hydraulic power units AND/OR accumulators; 
          (xi) control panel;
         (xii) test AND/OR handling skids; 
        (xiii) safety stands AND/OR test stumps

FLOWHEAD VALVE ASSEMBLIES, SUBSEA OIL AND/OR GAS WELL CONTROL, 
with OR without actuators, whether OR not assembled, including 
ALL of the following:
  (a) working pressure NOT less than 200 bar;
  (b) hydraulic valves;
  (c) elbows;
  (d) piping;
  (e) cage protector AND/OR work platform;
  (f) swivel

VALVES, STEAM, butterfly OR globe, having ALL of the following:
  (a) flanged connection;
  (b) stainless steel OR carbon steel body;
  (c) pneumatic actuator;
  (d) emergency handwheel;
  (e) diameter NOT less than 40 mm;
  (f) pressure rating NOT greater than 10 bar;
  (g) temperature rating NOT greater than 185 degrees Celsius

BUTTERFLY VALVES, double offset, having ALL of the following: 
  (a) stainless steel body;
  (b) wafer lug type;
  (c) metal seated;
  (d) pneumatic actuator with spring return; 
  (e) ATEX hazardous classification II 2G Eex d IIA T2

VALVES, floating ball, flanged, having ALL of the following:
  (a) stainless steel body AND ball;
  (b) polytetrafluoroethylene seat;
  (c) working pressure NOT greater than 20 bar;
  (d) pneumatic actuator with spring return; 
  (e) pilot pressure NOT greater than 4.5 bar;
  (f) ATEX hazardous classification II 2G Eex d IIA T5

WELL CONTROL MODULE, OIL AND GAS WELL, having BOTH of the 
following:
  (a) emergency disconnect package;
  (b) lower riser package,
with OR without ANY of the following:
          (i) housings;
         (ii) spacers;
        (iii) connectors;
         (iv) mandrels

MODULATING VALVES, having ALL of the following:
  (a) stainless steel housing;
  (b) stainless steel diaphragm actuator;
  (c) valve positioner

CONTROL VALVES, having ALL of the following:
  (a) stainless steel housing;
  (b) digital electro-pneumatic positioner;
  (c) diaphragm OR linear OR lifting piston actuator

DISC AND/OR BUTTERFLY VALVES, having ALL of the following:
  (a) pneumatic AND/OR diaphragm actuator;
  (b) diameter NOT less than 6 mm and NOT greater than
      208 mm;
  (c) working pressure NOT greater than 16 bar;
  (d) stainless steel housing,
with OR without control head AND/OR valve positioner

BUTTERFLY VALVES, manual OR actuator operated, having ALL of the 
following:
  (a) diameter NOT less than 6 mm and NOT greater than 
      208 mm;
  (b) cold operating pressure NOT greater than 16 bar;
  (c) stainless steel housing,
with OR without control head AND/OR valve positioner

TEST AND FLUSHING PLATES, FLUSHING ASSEMBLIES, SUBSEA OIL 
AND GAS WELL, quick connect, with OR without test valves

CIRCULATING TOOLS, OIL AND/OR GAS WELL, with OR without 
activation AND/OR shut-off ball

FUEL MODULES, GAS TURBINE, incorporating valves, including two 
OR more of the following:
  (a) pipes;
  (b) transmitter;
  (c) filter;
  (d) switches,
with OR without ANY of the following: 
           (i) gas pilot module;
          (ii) flameout module;
         (iii) air assist module;
         (iv) pressure compressor discharge system

BALL FLOAT VALVES, CISTERN

VALVES, BALL AND/OR BUTTERFLY AND/OR GATE AND/OR GLOBE, with OR  
without actuator, complying with ANY of the following 
standards:
  (a) American Petroleum Institute Standard 608 (API 608); 
  (b) International Standard 28921-1 (ISO 28921-1);
  (c) International Standard 15761 (ISO 15761);
  (d) International Association of Oil and Gas Producers
      Standard S-562(IOGP S-562)

ROTARY VALVES, FLOW CONTROL, self-cleaning, volumetric flow 
capacity NOT exceeding 1 000 m3/hr

KNIFE GATE VALVES, whether OR not assembled, having ALL of the 
following:
  (a) one piece cast ductile iron OR stainless steel body;
  (b) stainless steel OR nickel-molybdenum alloy knife gate
      having bevelled AND/OR rounded edges;
  (c) anti-extrusion ring;
  (d) flanges complying with ASME (American Society of Mechanical
      Engineers) B16.5 (2017),
with OR without actuator

CONTROL VALVES, MULTI-STAGE, ANGLE AND/OR GLOBE AND/OR Z TYPE
with OR without:
  (a) actuator;
  (b) positioners

PARTS, FIRE SUPPRESSION, being EITHER of the 
following:               
  (a) stainless steel valve, including ALL of the  
      following:  
          (i) 24 VDC solenoid; 
         (ii) 4 x relay switch;
        (iii) valves, lug, AND outlet;
         (iv) release pressure switch, 
  (b) external trim, including BOTH of the following:  
          (i)  6 mm release ball valve;  
         (ii) solenoid valves, 24 DC

GAS FUEL BLENDERS, assembled, including ALL of the following:
  (a) start-up strainer;
  (b) flow metre;
  (c) isolation valve; 
  (d) bleed valve;
  (e) bleed cavity pressure transmitters;
  (f) control valve;
  (g) outlet pressure transmitters;
  (h) skid mounted

VALVE ASSEMBLIES, HYDRAULIC EXCAVATOR, being service hatch 
modules including ALL of the following:
  (a) cooler fans;
  (b) hoses; 
  (c) electrical controls

BEVERAGE DISPENSERS, having ALL of the following:
  (a) cup dispenser;
  (b) cup conveyor;
  (c) point of sale connectivity

EXPLOSION DOORS, having ALL of the following:
  (a) door sizes being ANY of the following: 
          (i) 500 mm x 800 mm;
         (ii) 1 000 mm x 1 000 mm;
        (iii) 800 mm x 1 300 mm;
         (iv) 1 000 mm x 2 000 mm;
          (v) DN800;
         (vi) DN1150; 
        (vii) DN1400,
  (b) retaining device AND controller;
  (c) carbon fibre lid AND resetting springs, with OR without
      stainless-steel cassette OR case;
  (d) compressed air tank;
  (e) frame;
  (f) baffle plate; 
  (g) proximity switch, 
with OR without electrical heating elements OR vacuum 
breaker

SHUT OFF VALVES, male OR female fittings, having ALL of the 
following:
  (a) stainless steel body;
  (b) spring loaded valve AND o-ring seal;
  (c) valve internal bore hole diameter NOT greater than 20 mm

FLOW REGULATING VALVE STATIONS, MINE WATER, skid mounted, 
having all of the following:
  (a) single OR multiple stage with dual OR single stream 
      pressure regulation;
  (b) pressure regulating valves with a pressure rating 
      of NOT less than 24 MPa/3500 psi;
  (c) pressure gauges;
  (d) isolation AND surge relief AND drain valves;
  (e) strainer AND hose AND piping

ISOLATION VALVES, manual AND/OR actuated, having BOTH of the 
following:
  (a) low torque balanced plug;
  (b) working pressure NOT greater than 3 626 psi

SUBSEA ABANDONMENT MODULES, riserless, including ALL of the 
following: 
  (a) maximum working pressure rating NOT greater than 
      10 000 psi; 
  (b) hydraulic operating pressure NOT greater than 5 000 psi
  (c) maximum working depth NOT greater than 3 000 m

PIPE SEALING CLAMPS, VALVE ASSEMBLY, OIL AND GAS WELL

HYDRANT VALVES, BIB-NOSE, having ALL of the following:
  (a) valve inlet size NOT less than DN 80;
  (b) valve outlet size NOT greater than DN 65;
  (c) flanged connections;
  (d) handwheel operated

MANIFOLDS, PNEUMATIC PISTON GATE VALVE, modular, electrically 
actuated

BUTTERFLY VALVES, manual OR actuator operated, having BOTH of 
the following:
  (a) diameter NOT less than 500 mm and NOT greater than 
      3 500 mm;
  (b) working pressure NOT greater than 50 bar

VALVES, SOLENOID, MANIFOLD ASSEMBLIES, medical AND/OR laboratory

VALVE ASSEMBLY, GAS TURBINE, including actuator AND/OR driver

VALVES, GAS TURBINE, with OR without actuator

VALVES, BUTTERFLY OR CONTROL

SLIDES, PELLET MILL, pneumatic OR motor OR hydraulic operated

GAS MIXING AND/OR DISTRIBUTION STATIONS OR SKIDS, STEEL STRIP 
METAL COATING LINE, including ALL of the following:
  (a) valves;
  (b) piping;
  (c) steel support structure

VALVES, SAMPLE STATION, liquid AND/OR gas

SUBSEA PLATES, HORIZONTAL AND VERTICAL CONNECTION, including ALL 
of the following:
  (a) male AND female multi quick connection plates; 
  (b) gate valves; 
  (c) clamps

FLOW REGULATION ASSEMBLIES, GAS TURBINE, including ALL of the 
following:
  (a) piping;
  (b) reducers;
  (c) flanges;
  (d) shut off valves

SOLENOID ACTUATED VALVE ASSEMBLIES, TRANSMISSION HYDRAULIC 
CONTROL, including BOTH of the following:
  (a) electromagnetic actuator;
  (b) hydraulic valve body

PNEUMATIC VALVES, three way flow, having a working pressure NOT 
greater than 10 bar

DUST CATCHING AND/OR GAS CLEANING VALVES, BLAST FURNACE PLANT, 
being ANY of the following:
  (a) discharge AND/OR metering AND/OR stop valves;
  (b) isolation AND/OR knife AND/OR slide gate valves

SLURRY CIRCUIT BYPASS STATIONS, including ALL of the following:
  (a) steel structure;
  (b) steel pipes;
  (c) ball valves

STEAM TRAPS, ball float, forged carbon steel body AND flanged 
connections

COLUMNS, ION EXCHANGE AND/OR REGENERATION, skid mounted, whether 
OR not assembled, including ALL of the following: 
  (a) steel support structure with ladders; 
  (b) pipe support structure AND piping; 
  (c) valves

CABINETS, CLAY GUN, water AND temperature control, having BOTH 
of the following:
  (a) valves;
  (b) electric water heater

DAMPERS, FLARE STACK

BOTTLED BEVERAGE DISPENSER, counter top, having ALL of the 
following:
  (a) refrigerating unit;
  (b) portion control;
  (c) LED lighting

VALVES, goggle AND/OR isolating, being for ANY of the following:
  (a) blast furnace;
  (b) gas cleaning plant;
  (c) hot blast system;
  (d) gas main

DAMPERS, stainless steel, having plate thickness NOT less than 
2.5 mm