| Tariff Classification | TCO Number | TCO description | Operative date | Decision date |
| 8207.50.00 | 1532734 |
ROUNDING RINGS, POLYETHYLENE PIPE, galvanised steel, having ALL
of the following:
(a) rounding capacity diameter NOT less than 63 mm and
NOT greater than 250 mm;
(b) hinged;
(c) nut AND thread closure
| 26/08/2015 | 16/11/2015 |
| 8207.50.00 | 1408893 |
CORERS, DIAMOND TIPPED, having a diameter NOT greater than
600 mm
| 11/03/2014 | 11/06/2014 |
| 8207.50.00 | 1334347 |
BITS, MASONRY CORE, having ALL of the following:
(a) diamond segments;
(b) hex shank drive;
(c) diameter NOT less than 6 mm AND NOT greater than 50 mm
| 15/10/2013 | 23/12/2013 |
| 8207.50.00 | 1310247 |
TUBES, DRILL BIT, having a length NOT greater than 2 metres
| 22/03/2013 | 25/06/2013 |
| 8207.50.00 | 1142319 |
BITS, TAPHOLE, BLAST FURNACE
| 22/12/2011 | 19/03/2012 |
| 8207.50.00 | 9706979 |
DRILL BITS, ELECTRO-PNEUMATIC ROTARY HAMMER, tungsten carbide
tipped, having a shank geometry of EITHER of the following:
(a) slotted drive;
(b) triangular
| 11/08/1997 | 17/10/1997 |
| 8207.50.00 | 9511526 |
DRILLS, GUN, as follows:
(a) being ANY of the following;
(i) carbide tipped;
(ii) solid carbide;
(iii) solid carbide heads,
(b) having ALL of the following;
(i) standard driver;
(ii) coolant channels through centre;
(iii) tip off-centre,
(c) having EITHER of the following;
(i) length greater than 300 mm;
(ii) length less than or equal to 300 mm, with outside
diameter less than 6 mm or greater than 25.3 mm
| 26/10/1995 | 02/02/1996 |
| 8207.50.00 | 9801081 |
DRILLS, chisel tip auger
| 05/02/1998 | 17/04/1998 |
| 8207.50.00 | 9310250 |
SAW DRILLS, being drill bits that use the first 25mm (one inch) or
so of the drill bit to drill through the desired material, then use
the rest of the special shaft as a cutting tool or saw
| 17/09/1993 | 31/12/1993 |
| 8207.50.00 | 9800403 |
COMPOSITE TOOL BODIES (HOLDERS), METAL WORKING, but NOT including
tool bodies imported with tool tips, plates or sticks
| 15/01/1998 | 27/03/1998 |
| 8207.50.00 | 9501331 |
GUN DRILLS, having ALL of the following:
(a) being ANY of the following:
(i) carbide tipped;
(ii) solid carbide;
(iii) solid carbide heads;
(b) having ALL the following:
(i) standard driver;
(ii) coolant channels through centre;
(iii) tip off centre;
(c) but NOT including ANY of the following:
(i) diameter exceeding 5.99 mm but NOT exceeding 25.3 mm;
(ii) length NOT greater than 300 mm
| 01/02/1995 | 23/06/1995 |
| 8207.50.00 | 9600818 |
DRILL BITS, MASONARY, HAMMER, having BOTH of the following:
(a) slotted shank;
(b) hammer proof carbide tip
| 25/12/1995 | 31/03/1996 |
| 8207.50.00 | 9902708 |
BITS, AUGER, scotch pattern
| 19/04/1999 | 09/07/1999 |
