Tariff Concession Orders

PIG IRON, comprising ALL of the following:
   (a) carbon, with a composition less than 5%;
   (b) sulphur;
   (c) silicon;
   (d) phosphorus;
   (e) manganese

BILLETS, square, semi-finished non-alloy steel, having ALL of 
the following:
  (a) thickness AND width NOT less than 120 mm x 120 mm and NOT 
      greater than 170 mm x 170 mm;
  (b) length NOT less than 7.0 m and NOT greater than 13.0 m;
  (c) carbon content by weight LESS than 0.25%

BILLETS, square, semi-finished non-alloy steel, having ALL of 
the following:
  (a) thickness AND width NOT less than 120 mm x 120 mm  and NOT 
      greater than 170 mm x 170 mm;
  (b) length NOT less than 7.0 m and NOT greater than 13.0 m; 
  (c) carbon content 0.25% by weight OR greater

BARS, continuous cast, cast iron, in lengths not exceeding 3 200 
mm

STEEL, flat rolled non-alloy, electrolytically coated with zinc,
 having ALL of the following features;
   (a) a thickness of 2.39mm or more;
   (b) a width NOT less than 1219mm and NOT greater than 1249 mm;
   (b) to specification JIS G3313 SECC or SEHC

STEEL COILS, hot dipped zinc-aluminium-magnesium alloy coated, 
having ALL of the following:
  (a) yield strength NOT less than 380 MPa and NOT greater than
      560 MPa;
  (b) tensile strength NOT less than 440 MPa and NOT greater
      than 640 MPa;
  (c) elongation NOT less than 11%;
  (d) total coating mass NOT less than 150 g/m2;
  (e) total coated thickness NOT less than 3.70 mm;
  (f) coil width NOT less than 800 mm and NOT greater than 
      1 400 mm;
  (g) coated with a zinc-aluminium-magnesium alloy, having a
      composition by weight of:
          (i) NOT less than 2% and NOT greater than 4% magnesium;
         (ii) NOT less than 3% and NOT greater than 5% aluminium;
        (iii) less than 1% of minor additions;
         (iv) zinc NOT greater than 95%

SHEETS, flat rolled, non-alloy steel, hot dipped galvanized zinc 
coated, having ALL of the following:
  (a) yield strength NOT less than 450 MPa;
  (b) tensile strength NOT less than 480 MPa;
  (c) total elongation NOT less than 10%;
  (d) total coating mass on ALL sides NOT less than 275 g/m2;
  (e) thickness 4.0 mm AND width 1 200 mm AND length 2 160 mm
For the purposes of this Order, tolerances allowable for 
specification (e) are as follows:
           (i) thickness +/- 0.2 mm;
          (ii) width +/- 5 mm;
         (iii) length +/- 10 mm

COILS, non-alloy steel, hot rolled, zinc coated, complying with 
American Society for Testing and Materials Standard
A653/A653M- 11 (ASTM A653/A653M-11), having ALL of the 
following: 
  (a) thickness NOT less than 3.60 mm and NOT greater than 
      6.0 mm;
  (b) width NOT less than 784 mm and NOT greater than 1 263 mm;
  (c) minimum yield strength NOT less than 175 Mpa;
  (d) minimum tensile strength NOT less than 280 Mpa;
  (e) inside diameter NOT less than 711 mm and NOT greater than
      813 mm; 
  (f) zinc coating mass NOT less than 0.040 kg/m2 per side; 
  (g) weight NOT less than 14 metric tonnes; 
  (h) chemical composition by weight of ALL of the following: 
          (i) carbon content NOT greater than 0.20%; 
         (ii) phosphorus content NOT greater than 0.03%; 
        (iii) sulphur content NOT greater than 0.03%; 
         (iv) aluminium content NOT greater than 0.10%; 
          (v) copper content NOT greater than 0.25%; 
         (vi) nickel content NOT greater than 0.25%; 
        (vii) titanium content NOT greater than 0.04%; 
       (viii) silicon content NOT greater than 0.45%

STEEL COILS, hot dipped zinc-aluminium-magnesium alloy coated, 
having ALL of the following:
  (a) yield strength NOT less than 420 MPa and NOT greater than 
      520 MPa;
  (b) tensile strength NOT less than 470 MPa and NOT greater
      than 590 MPa;
  (c) elongation NOT less than 17%;
  (d) total coating mass NOT less than 150 g/m2;
  (e) total coated thickness NOT less than 3.70 mm;
  (f) coil width NOT less than 800 mm and NOT greater than
      1 400 mm;
  (g) coated with a zinc-aluminium-magnesium alloy, having a 
      composition by weight of:
      (i) NOT less than 2% and NOT greater than 4% magnesium;
     (ii) NOT less than 3% and NOT greater than 5% aluminium;
    (iii) less than 1% of minor additions;
     (iv) balance zinc

STEEL, flat rolled, non-alloy, hot-dipped galvannealed zinc 
coated, in coils, having ALL of the following:
  (a) yield strength NOT less than 275 MPa and NOT greater than
      380 MPa;
  (b) tensile strength NOT less than 440 MPa;
  (c) elongation NOT less than 29%;
  (d) coating mass NOT less than 35 g/M2 and NOT greater than 
      65 g/M2 on each side;
  (e) in ANY of the following sizes:
        (i) thickness 1.20 mm and width 908 mm
       (ii) thickness 2.00 mm and width 1 130 mm
For the purposes of this order, tolerances allowable for
specification (e) are:
  (a) thickness +/- 10%
  (b) width +/- 1%

STEEL, flat rolled, non-alloy, hot dipped galvannealed 
zinc coated, in coils, having ALL of the following:
  (a) yield strength NOT less than 135 MPa and NOT greater than
      225 MPa;
  (b) tensile strength NOT less than 270  MPa;
  (c) elongation NOT less than 40% and NOT greater than
      50%;
  (d) coating mass NOT less than 35 g/m2 and NOT greater 
      than 65 g/m2;
  (e) thickness 0.70 mm and width 1 660 mm
For the purposes of this order, tolerances allowable for 
specification (e) are:
  (a) thickness +/- 10%
  (b) width +/- 1%

STEEL, flat rolled, non-alloy, hot dipped galvannealed zinc 
coated, in coils, having ALL of the following:
  (a) yield strength NOT less than 135 MPa and NOT greater 
      than 225 MPa;
  (b) tensile strength NOT less than 270 MPa;
  (c) elongation NOT less than 40% AND not greater than 50%;
  (d) coating mass NOT less than 35 g/m2 and NOT greater 
      than 65 g/m2;
  (e) in ANY of the following sizes:
          (i) thickness 0.65 mm and width 1 700 mm;
         (ii) thickness 0.70 mm and width 1 540 mm;
        (iii) thickness 0.70 mm and width 1 440 mm;
         (iv) thickness 0.75 mm and width 1 000 mm;
          (v) thickness 0.70 mm and width 1 170 mm
For the purposes of this order, tolerances allowable for
specification (e) are:
  (a) thickness +/- 10%
  (b) width +/- 1%

STEEL, flat rolled, non-alloy steel, hot dipped galvannealed 
zinc coated, in coils, having ALL of the following:
  (a) yield strength NOT less than 195 MPa and NOT greater than 
      295 MPa;
  (b) tensile strength NOT less than 340 MPa;
  (c) elongation NOT less than 34% and NOT greater than 44%;
  (d) total coating mass NOT less than 35 g/m2 and NOT greater
      than 65 g/m2;
  (e) in EITHER of the following sizes:
        (i) thickness 0.70 mm AND width 818 mm;
       (ii) thickness 0.70 mm and width 855 mm
For the purposes of this order, tolerances allowable for 
specification (e) are:
  (a) thickness +/- 10%
  (b) width +/- 1%

COILS, non-alloy steel, hot rolled, zinc coated, complying with 
American Society for Testing and Materials Standard  A653/A653M-
11 (ASTM A653/A653M-11), having ALL of the following:
  (a) thickness NOT less than 2.75 mm and NOT greater than 
      6.0 mm;
  (b) width NOT less than 784 mm and NOT greater than 
      1 263 mm;
  (c) minimum yield strength NOT less than 330 Mpa;
  (d) minimum tensile strength NOT less than 430 Mpa;
  (e) inside diameter NOT less than 711 mm and NOT greater 
      than 813 mm;
  (f) zinc coating mass NOT less than 0.080 kg/m2 per side;
  (g) weight NOT less than 14 metric tonnes;
  (h) chemical composition by weight of ALL of the following:
          (i) carbon content NOT greater than 0.20%;
         (ii) manganese content NOT less than 0.30% and NOT
              greater than 0.90%;
        (iii) phosphorus content NOT greater than 0.03%;
         (iv) sulphur content NOT greater than 0.03%;
          (v) chromium content less than 0.30%;
         (vi) molybdenum content less than 0.08%;
        (vii) aluminium content NOT greater than 0.10%;
       (viii) copper content NOT greater than 0.25%;
         (ix) nickel content NOT greater than 0.25%;
          (x) titanium content NOT greater than 0.04%;
         (xi) vanadium content less than 0.10%;
        (xii) silicon content NOT greater than 0.45%

TIN FREE STEEL, flat rolled, in coils, chromium plated, having 
ALL of the following:
  (a) width NOT less than 750 mm and NOT greater than 1 000 mm;
  (b) thickness NOT greater 0.30 mm;
  (c) temper designation of 61 to 76 (both inclusive) in
      accordance with Rockwell hardness 30 T range

STEEL, aluminium coated, flat rolled, coil, conforming to ASTM A463
 OR JIS G 3314, chromated OR non chromated, having ANY combination
 of the following characteristics:
   (a) coating:
          (i) T125;
         (ii) T140;
   (b) quality:
          (i) CQ;
         (ii) DQ;
        (iii) DDQ

SHEET, STEEL, aluminium coated to American Society 
of Testing and Materials A 463 (ASTM A 463) having ANY 
combination of the following:
  (a) coating:
        (i) T1-25;
       (ii) T1 - 40
  (b) quality:
        (i) CS; 
       (ii) DDS

SHEET, COMPOSITE, galvanized steel laminated with polyvinyl 
chloride, having BOTH of the following:
  (a) steel thickness NOT less than 0.6 mm;
  (b) polyvinyl chloride laminate thickness NOT less than
      0.8 mm

CERAMIC STEEL, being two layers of enamel fused onto high grade
 steel

HOOP AND STRIP, hardened and tempered

HOOP AND STRIP, hardened and tempered

STEEL, flat rolled, in coil form, continuous annealed, zinc 
coated, epoxy lacquered, having BOTH of the following:
  (a) thickness NOT greater than 0.4 mm;
  (b) width NOT greater than 90 mm

SHEETS AND/OR STRIPS, STEEL, NON-ORIENTATED ELECTRICAL, as 
described in ANY of the following international standards:
  (a) Japanese Industrial Standard C 2552;
  (b) American Society for Testing and Materials 
      Standard A 677-05;
  (c) European Standard EN 10106

SHEETS AND/OR STRIPS, STEEL, NON-ORIENTATED ELECTRICAL, as 
described in ANY of the following international standards:
  (a) Japanese Industrial Standard C 2552;
  (b) American Society for Testing and Materials 
      Standard A 677-05;
  (c) European Standard EN 10106

RODS, WIRE, hot rolled, free cutting steel, Grade 12L 14

RODS, iron OR non-alloy steel, in coils, hot rolled, complying 
with the Australian Standard AS 1442-2007, Table 1, Grade 
designation 1020, having a rod diameter NOT less than 21 mm AND 
having a composition by weight of BOTH of the following:
  (a) carbon content NOT less than 0.18% and NOT greater 
      than 0.23%;
  (b) manganese content NOT less than 0.30% and NOT greater 
      than 0.60%

STEEL BARS, complying with American Society of Testing and 
Materials Standard A350-LF2 (ASTM A350-LF2)

BARS, HEXAGONAL, hot rolled, free cutting steel, grade 12 L 14

BARS, ROUND, hot rolled, free cutting steel, Grade 12L 14

BARS, non-alloy steel, flat, square OR round edge, complying 
with British Standard BS EN 10025-2:2004(E), having ALL of the 
following:
  (a) width NOT less than 98 mm and NOT greater than 102 mm;
  (b) thickness NOT less than 48 mm and NOT greater than 52 mm;
  (c) manganese content less than 1.65%

BARS, NON-ALLOY STEEL, having ALL of the following:
  (a) rectangular cross-section;
  (b) electrical resistivity NOT greater than 20 Micro Ohms 
      per centimetre;
  (c) carbon content NOT greater than 0.06 percent

STEEL BARS, hexagonal, hot rolled steel, across the flat NOT 
less than 33 mm and NOT greater than 65 mm

BARS, round, complying with Japanese Industrial Standard JIS G 
4051 (1979), class S20C OR class S45C, having a bar diameter 
NOT less than 100 mm

BARS, NON-ALLOY STEEL, having BOTH of the following:
  (a) electrical resistivity NOT greater than 20 Micro Ohms
      per centimetre;
  (b) carbon content NOT greater than 0.06 percent

BARS, square, steel, bright OR cold finished, having an across
 flat dimension of 40 mm or greater but NOT exceeding 150 mm

BARS, hexagon, bright OR cold finished to AS 1443-1994
 specifications, having an across the flat dimension in ANY of the
 following sizes:
   (a) 57.15 mm;
   (b) 60.325 mm;
   (c) 60.00 mm;
   (d) 62.00 mm OR greater

BARS, square, steel, bright OR cold finished, having an across
 flat dimension of 40 mm or greater but NOT exceeding 150 mm

BARS, flat, steel, bright or cold finished, having dimensions
 wider than 100 mm or thickness greater than 25 mm

BARS, rectangular, bright drawn carbon steel, greater than 3 mm
 width and thickness

BARS, flat, cold-rolled or cold-drawn, having ALL of the 
following:
  (a) carbon NOT less than 0.18% and NOT greater than 0.23%;
  (b) manganese NOT less than 0.3% and NOT greater than 0.65%;
  (c) phosphorus NOT greater than 0.04%;
  (d) sulphur NOT greater than 0.05%; 
  (e) thickness 10 mm AND width 40 mm;
  (f) length 3 000 mm
For the purposes of this Order, tolerances allowable for 
specification (e) are +0.0 mm and -0.10 mm and (f) are +100 mm 
and -0.0 mm

WELDING TRANSITION JOINTS, composed of dissimilar metals,
 explosion bonded, allowing dissimilar metals to be welded together

I-BEAMS, tapered flange, hot-rolled, complying with Australian 
Standard/New Zealand Standard 3679.1-300 (AS/NZS 3679.1-300) OR 
Australian Standard/New Zealand Standard 3679.1-350 (AS/NZS 
3679.1-350), having ALL of the following:
  (a) length greater than 5.9 m but NOT greater than 15.1 m;
  (b) nominal flange widths of either 45.0 mm OR 65.0 mm;
  (c) flange thickness greater than 5.9 mm but NOT greater
      than 8.6 mm;
  (d) mass greater than 7.1 kg/m but NOT greater than 13.2 kg/m;
  (e) height NOT greater than 130 mm

I BEAMS, hot rolled, having EITHER of the following:             
  (a) depth NOT less than 356 mm (14 in) and a flange width NOT 
      less than 368 mm (14.5 in);
  (b) depth NOT less than 762 mm (30 in) and a flange width NOT
      less than 267 mm (10.5 in)

PARTS, CRANE PALLET, being structural lifting rails

UNEQUAL ANGLES, hot-rolled steel sections, complying with 
Australian and New Zealand Standard AS/NZS 3679.1:2016, Grade 
300 OR Grade 350, having EITHER of the following:
  (a) leg size 150 mm x 90 mm having ANY of the following:
         (i) thickness being 8 mm OR 10 mm OR 12 mm; 
        (ii) lengths of 9 m OR 10.5 m OR 12 m,
  (b) leg size 150 mm x 100 mm having ANY of the following:
         (i) thickness being 10 mm OR 12 mm; 
        (ii) lengths of 9 m OR 10.5 m OR 12 m

STRUTS, CHANNEL, non-alloy steel

COUPLINGS, hot dipped galvanised steel, being EITHER of the 
following:
   (a) gripping couplings;
   (b) linking couplings

HANGING TRACKS, STRIPPING AND BRACKETS, steel, wall mounted, 
having spaced screw holes

STRIP, SOIL REINFORCEMENT, having ALL of the following:
  (a) composition to Australian Standard AS3679.1 Grade 350 
      or equivalent;
  (b) hot rolled;
  (c) transverse ribs, having a height NOT less than 2.5 mm and
      NOT greater than 4.5 mm; 
  (d) galvanized;
  (e) attachment holes at one or both ends of the strip;
  (f) width NOT less than 40 mm and NOT greater than 60 mm; 
  (g) thickness NOT less than 3 mm and NOT greater than 10 mm,
      excluding height of ribs; 
  (h) length NOT greater than 15 metres

WIRE, brick cutting

WIRE, music spring, having ANY of the following finishes:
   (a) bright;
   (b) cadmium;
   (c) cadmium/zinc alloy;
   (d) galvanised;
   (e) phosphate;
   (f) polished;
   (g) tinned

WIRE, steel, to ANY of the following Specifications:
   (a) ASTM A230, A232 or A401;
   (b) SAE J351 or 50100 to 52100 (both inclusive);
   (c) DIN 17223;
   (d) BS 1408 Type D or 2803;
   (e) JIS G3561

WIRE, to the following Specifications:
   (a) ASTM A230;
   (b) DIN 17223

TIE WIRE, REBAR TYING TOOL, on reels

WIRES, FASTENER, complying with American Iron and Steel 
Institute (AISI) Standard 1022

WIRE, STEEL, having BOTH of the following:
   (a) diameter NOT less than 2.5 mm but NOT exceeding 3.5 mm;
   (b) chemical composition by weight of ALL of the following:
            (i) carbon      0.06% to 0.14%;
           (ii) phosphorus  0.03% to 0.09%;
          (iii) manganese   0.04% to 1.00%;
           (iv) silicon     0.14% maximum;
            (v) sulphur     0.01% to 0.04%

WIRE, STEEL, having BOTH of the following:
   (a) diameter NOT less than 2.5 mm but NOT exceeding 3.5 mm;
   (b) chemical composition by weight of ALL of the following:
         (i) carbon         0.06% to 0.11%;
        (ii) phosphorus     0.04% to 0.08%;
       (iii) manganese      0.80% to 1.00%;
        (iv) silicon        0.01% maximum;
         (v) sulphur        0.015% to 0.07%;
        (vi) nickel         0.006% to 0.012%;
       (vii) aluminium      0.005% maximum

WIRE, galvanised, annealed, non-alloy steel, having ALL of the
 following characteristics:
   (a) diameter of 1.00 mm or less;
   (b) diameter tolerance + 0.02 mm - 0.01 mm;
   (c) tensile strength 300 - 400 N/mm2;
   (d) elongation 18% minimum;
   (e) torsion 44 turns minimum

STAPLE WIRE, galvanised

WIRE, galvanised, dia less than 0.90 mm

ROPE WIRE, redrawn, having ALL of the following:
  (a) diameter NOT less than 2.995 mm and NOT greater than
      4.025 mm;
  (b) coating having BOTH of the following:
        (i) 95% zinc;
       (ii) 5% aluminium,
  (c) coating NOT less than 150 g/m2 and NOT greater than 
      217 g/m2;
  (d) tensile strength NOT less than 1 770 N/mm2 and NOT greater
      than 2 030 N/mm2

WIRE, music spring, having ANY of the following finishes:
   (a) bright;
   (b) cadmium;
   (c) cadmium/zinc alloy;
   (d) galvanised;
   (e) phosphate;
   (f) polished;
   (g) tinned

WIRE, fastener, soft drawn, to ANY of the following
 Specifications:
   (a) AISI Grade C1038;
   (b) AISI Grade C1039;
   (c) AISI Grade C1040;
   (d) AISI Grade C1041;
   (e) AISI Grade K1038;
   (f) AISI Grade K10B30

WIRE, fastener, soft drawn, to ANY of the following
 Specifications:
   (a) AISI Grade C1010;
   (b) AISI Grade C1018;
   (c) AISI Grade C1022;
   (d) AISI Grade K1012;
   (e) AISI Grade K1013;
   (f) AISI Grade K1016;
   (g) AISI Grade K1018;
   (h) AISI Grade K1019;
   (i) AISI Grade K1022;
   (j) AISI Grade K10B18;
   (k) AISI Grade K10B21

WIRE, SPIRAL BINDING, nylon coated, continuous roll, diameter
 0.74 mm to 2.00 mm (inclusive)

WIRE, STEEL, being hard drawn low carbon (HDLC) wire, phosphate 
coated, having ALL of the following:
  (a) diameter NOT less than 18.00 mm but NOT greater than 
      20.00 mm;
  (b) chemical composition by weight of ALL of the following:
          (i) carbon      0.04% to 0.10%;
         (ii) phosphorus  0.03% maximum;
        (iii) manganese   0.40% to 0.60%;
         (iv) silicon     0.12% to 0.24%;
          (v) sulphur     0.03% maximum

INGOTS, stainless steel, weight exceeding 2.5 tonnes

BILLETS, stainless steel, having a chromium content NOT less 
than 10.5%

BILLETS OR BLOOMS, stainless steel, square, forged and ground,
 having a section measurement of NOT less than 75 mm and NOT
 greater than 500 mm

FLAT ROLLED PRODUCTS OF STAINLESS STEEL, having a thickness of
 4.75 mm or more but NOT exceeding 10 mm

COILS, stainless steel, to ASTM A240, in ANY of the following
 grades:
   (a) 316;
   (b) 316L;
   (c) 304;
   (d) 304L;
   (e) 321;
   (f) UNS S41050

FLAT ROLLED PRODUCTS OF STAINLESS STEEL, having a thickness of 3 mm
 or more but less than 4.75 mm

FLAT ROLLED PRODUCTS, having a nickel content exceeding 22.5%
 by weight

FLAT ROLLED PRODUCTS OF STAINLESS STEEL, having a thickness
 exceeding 10 mm

PLATES, stainless steel, to specification ASTM A240, having a
 thickness exceeding 10 mm and a width exceeding 600 mm

PLATES, stainless steel, types 304 and 316 to ASTM A240

FLAT ROLLED PRODUCTS, having a nickel content exceeding 22.5%
 by weight

FLAT ROLLED PRODUCTS OF STAINLESS STEEL, having a thickness of
 4.75 mm or more but NOT exceeding 10 mm

PLATES, stainless steel, to specification ASTM A240, having a
 thickness exceeding 6 mm but NOT exceeding 10 mm and a width
 exceeding 600 mm

PLATES, stainless steel, types 304 and 316 to ASTM A240, having a
 thickness greater than 6mm

FLAT ROLLED PRODUCTS OF STAINLESS STEEL, having a thickness of 3 mm
 or more but less than 4.75 mm

FLAT ROLLED PRODUCTS OF STAINLESS STEEL, having a thickness of less
 than 3 mm

FLAT ROLLED PRODUCTS OF STAINLESS STEEL, having a thickness of
 4.75 mm or more

FLAT ROLLED PRODUCTS OF STAINLESS STEEL, having a thickness of 3 mm
 or more but less than 4.75 mm

PLATES, SHEETS OR COILS, stainless steel, to ASTM A240, in ANY of
 the following grades:
   (a) 316;
   (b) 316L;
   (c) 304;
   (d) 304L;
   (e) 321;
   (f) UNS S41050;
   (g) 430

FLAT ROLLED PRODUCTS OF STAINLESS STEEL, having a thickness
 exceeding 1 mm but less than 3 mm

PLATES, SHEETS OR COILS, stainless steel, to ASTM A240, in ANY of
 the following grades:
   (a) 316;
   (b) 316L;
   (c) 304;
   (d) 304L;
   (e) 321;
   (f) UNS S41050;
   (g) 430

SHEETS, stainless steel, NOT less than 600 mm in width

FLAT ROLLED PRODUCTS OF STAINLESS STEEL, having a thickness of
 0.5 mm or more but NOT exceeding 1 mm

PLATES, SHEETS OR COILS, stainless steel, to ASTM A240, in ANY of
 the following grades:
   (a) 316;
   (b) 316L;
   (c) 304;
   (d) 304L;
   (e) 321;
   (f) UNS S41050

FLAT ROLLED PRODUCTS OF STAINLESS STEEL, having a thickness of less
 than 0.5 mm

PLATES, SHEETS OR COILS, stainless steel, to ASTM A240, in ANY of
 the following grades:
   (a) 316;
   (b) 316L;
   (c) 304;
   (d) 304L;
   (e) 430

CAUL PLATES (melamine press plates), stainless steel, being 2 650 mm
 x 1 350 mm OR greater

FLAT ROLLED PRODUCTS OF STAINLESS STEEL

SHEET, COMPOSITE, stainless steel laminated with polyvinyl 
chloride, having BOTH of the following:
  (a) steel thickness NOT less than 0.6 mm;
  (b) polyvinyl chloride laminate thickness NOT less than
      0.8 mm

FLAT ROLLED PRODUCTS OF STAINLESS STEEL, having a thickness of
 4.75 mm or more

FLAT ROLLED PRODUCTS OF STAINLESS STEEL, having a thickness of less
 than 4.75 mm

STRIP, stainless steel, thickness less than 0.26 mm, of
 rectangular section, of a width NOT exceeding 500 mm and of
 such dimension that the thickness does NOT exceed one tenth
 of the width

FLAT ROLLED PRODUCTS OF STAINLESS STEEL, NOT further worked than
 cold-rolled (cold-reduced)

PLATES, SHEETS OR COILS, stainless steel, to ASTM A240, in ANY of
 the following grades:
   (a) 316;
   (b) 316L;
   (c) 304;
   (d) 304L;
   (e) 321;
   (f) UNS S41050;
   (g) 430

STRIP, stainless steel, grade 301, in coils, thickness NOT
 exceeding 0.3 mm, width NOT exceeding 600 mm

BANDING, stainless steel, to AISI 201 or 316, of a width less than
 35 mm and a thickness of less than 1.25 mm

FLAT ROLLED PRODUCTS OF STAINLESS STEEL

BARS AND RODS, hot rolled in irregularly wound coils, stainless
 steel, Dia. 40mm or less

BARS OR STRIP, stainless steel, flat, hot rolled, cut to length,
 in ANY of the sizes listed in the following TABLE
                                  THE TABLE
           Thickness                              Width
   (a) less than 0.55 mm                    less than 152 mm
   (b) 0.55 mm to 3 mm                      less than 24 mm
   (c) greater than 3 mm                    less than 25 mm
   (d) greater than 13 mm                   less than 204 mm

BARS, flat, stainless steel, in ANY of the sizes
 listed in the following TABLE
                          THE TABLE
          Thickness                               Width
   (a) less than 0.55 mm                     less than 152 mm
   (b) 0.55 mm to 3 mm                       less than 24 mm
   (c) greater than 3 mm                     less than 25 mm
   (d) greater than 13 mm                    less than 204 mm

BARS, stainless steel, square, having an across the flat dimension
 NOT exceeding 50.8 mm

BARS AND RODS, stainless steel, to specification DIN X42Cr13,
 AISI 420 or ASTM 420

BARS, flat, stainless steel, hot rolled, annealed and pickled,
thickness NOT less than 3 mm and width NOT greater than 250 mm

BARS, flat, stainless steel, in ANY of the sizes listed in the
 following TABLE
                          THE TABLE
          Thickness                               Width
   (a) less than 0.55 mm                     less than 152 mm
   (b) 0.55 mm to 3 mm                       less than 24 mm
   (c) greater than 3 mm                     less than 25 mm
   (d) greater than 13 mm                    less than 204 mm

BARS, stainless steel, composition conforming to UNS S31803

BARS OR RODS, stainless steel, grade UNS S 32750 having the
 following chemical composition:
   (a) carbon         0.030% maximum;
   (b) silicon        0.30%;
   (c) manganese      0.40%;
   (d) phosphorus     0.030%;
   (e) sulphur        0.020%;
   (f) chromium       25%;
   (g) nickel         10%;
   (h) molybdenum     4%;
   (i) nitrogen       0.25%

BARS AND RODS, UNS alloy No. S20910, certified to
 Specification ASTM A276 or ASTM A314

BARS AND RODS, stainless steel, to Specifications AISI 634,
 AISI 630 or similar

BARS, stainless steel, hexagonal

BARS, stainless steel, square, having an across the flat dimension
 NOT exceeding 50.8 mm

BARS AND/OR RODS, stainless steel

TIES AND/OR RODS, WALL, helical, stainless steel

BARS AND/OR RODS, stainless steel, round, having BOTH of the 
following:
  (a) diameter NOT less than 14.29 mm;
  (b) compliance with American Society for Testing and Materials 
      (ASTM), A 582/A 582M-05 and/or A 276-06, Types 303, 304, 
      304L, 310, 316, 316L, 321, 410, 416, 420, 431, 440A,
      440B, 440C or 446

BARS AND/OR RODS, STAINLESS STEEL, CENTRELESS GROUND, having an 
diameter GREATER than 3.10 mm, but NOT greater than 28.6 mm, to 
ANY of the following grades:
  (a) 304 and/or 304L;
  (b) 316 and/or 316L;
  (c) 303;
  (d) 630;
  (e) 2205;
  (f) 431;
  (g) 416;
  (h) 410;
  (i) 420;
  (j) 446;
  (k) 440;
  (l) 310;
  (m) 321;
  (n) 253ma

BARS AND RODS, stainless steel, centreless ground, having an
 outside diameter exceeding 28.58 mm, to grades 303 OR 304 OR
 304L OR 316 OR 316L OR 431

BARS AND/OR RODS, ribbed, cold formed, stainless steel

RODS, WELDING, TUNGSTEN INERT GAS, stainless steel, diameter NOT
 exceeding 3.2 mm

BARS AND RODS, stainless steel, round, with an outside diameter
 exceeding 28.75 mm to grades 303 OR 304 OR 304L OR 316 OR 316L OR
 431

BARS OR RODS, stainless steel, round, diameter exceeding 28.57 mm to
 grades 304 OR 304L OR 316 OR 316L

BARS, flat, stainless steel, in ANY of the sizes listed in the
 following TABLE
                          THE TABLE
          Thickness                               Width
   (a) less than 0.55 mm                     less than 152 mm
   (b) 0.55 mm to 3 mm                       less than 24 mm
   (c) greater than 3 mm                     less than 25 mm
   (d) greater than 13 mm                    less than 204 mm

BARS, stainless steel, composition conforming to UNS S31803

BARS AND/OR RODS, STAINLESS STEEL

BARS AND/OR RODS, stainless steel, forged

RODS, WELDING

ANGLES, stainless steel

PROFILES, stainless steel, hot extruded

SECTIONS, laser fusion welded, stainless steel, complying with 
American Society for Testing and Materials ATSM A1069/A1069M

STRUTS, CHANNEL, stainless steel

CHANNELS, STAINLESS STEEL, HOT ROLLED, ANNEALED AND PICKLED, 
complying with American Society for Testing and Materials A 276
(ASTM A 276), having ALL of the following:
   (a) width NOT less than 20 mm;
   (b) height NOT less than 10 mm;
   (c) thickness NOT less than 2 mm and NOT greater than 30 mm

WIRE, circular section, NOT exceeding 0.274 mm dia

WELDING WIRE, stainless steel, tungsten inert gas, dia NOT
 exceeding 1.2 mm

WELDING WIRE, stainless steel, metal inert gas, dia NOT
 exceeding 1.6 mm

WIRE, stainless steel, round OR square OR oval OR flat with 
square edge OR flat with rounded edge, cold rolled and polished, 
flat section, thickness NOT exceeding 0.75 mm, OR, if exceeding 
0.75 mm having a width to thickness ratio exceeding 6:1

WIRE, spring temper stainless steel,round OR square OR oval OR 
flat with square edge OR flat with rounded edge, diameter 
exceeding 0.46 mm but NOT exceeding 1.2 mm

WELDING WIRE, stainless steel, gas metal arc welding, diameter NOT
 exceeding 1.6 mm

WIRE, STAINLESS STEEL, round OR square OR oval OR flat with 
square edge OR flat with rounded edge, cold drawn, bright 
finished, conforming to Euronorm No 1.4835 (EN 1.4835), having a 
diameter NOT less than 0.5 mm and NOT greater than 12 mm

WIRE, STAINLESS STEEL, round OR square OR oval OR flat with 
square edge OR flat with rounded edge, cold drawn, bright 
finished, having BOTH of the following:
  (a) diameter  NOT less than 0.5 mm and NOT greater than 12 mm;
  (b) conforming to ANY of the following AISI grades:
          (i) 304;
         (ii) 304L;
        (iii) 310;
         (iv) 316;
          (v) 316L

WIRE, stainless steel, round OR square OR oval OR flat with 
square edge OR flat with rounded edge

WIRE, stainless steel, round OR square OR oval OR flat with 
square edge OR flat with rounded edge, to AISI specifications 
301 or 304, resin or nickel coated, diameter 0.15 mm to 6.55 mm 
inclusive

DETECTABLE WARNING TAPE, polyethylene, printed, incorporating 
stainless steel tracer wires

WIRE, stainless steel, annealed, conforming to American Iron and 
Steel Institute Standard (AISI) Type Number 304, having a 
diameter NOT greater than 0.8 mm

BILLETS, square, semi-finished alloy steel, having BOTH of the 
following:
  (a) thickness AND width NOT less than 120 mm x 120 mm and NOT 
      greater than 170 mm x 170 mm;
  (b) length NOT less than 7.0 m and NOT greater than 13.0 m

DISCS AND/OR SQUARES, alloy steel, hot rolled, hardened AND 
tempered, having ALL of the following:
  (a) diameter NOT less than 295 mm and NOT greater than 
      2 005 mm; 
  (b) thickness NOT less than 1.6 mm and NOT greater than NOT
      greater than 12.4 mm;
  (c) carbon content NOT less than 0.70%;
  (d) chrome content NOT less than 0.30%;
  (e) flatness deviation NOT greater than 1.50%

PROFILES, alloy steel, hot extruded

SHEET, electrical steel, containing from 2.7% to 3.3% (both
 inclusive) by weight of silicon

SHEETS OR STRIPS, silicon-electrical steel, grain oriented, 
cold rolled, in coil OR sheet form, having a width of NOT less 
than 600 mm

SHEET, electrical steel, containing from 2.7% to 3.3% (both
 inclusive) by weight of silicon

SHEETS AND/OR STRIPS, STEEL, NON-ORIENTATED ELECTRICAL, as 
described in ANY of the following international standards:
  (a) Japanese Industrial Standard C 2552;
  (b) American Society for Testing and Materials 
      Standard A 677-05;
  (c) European Standard EN 10106

PLATES AND SHEET, alloy steel, containing more than 11% by weight
 of manganese and more than 0.8% carbon

PLATES, SHEETS AND FLATS, high alloy steel, to specification
 DIN 40CrMnNiMo8 6 4, hardened and tempered within the range of
 980 N - 1 080 N per square millimetre (both inclusive)

PLATE, SHEET AND BAR, high alloy steel, specification DIN
 X40CrMoV51, BS BH13 or AISI H13

PLATES, SHEETS AND FLATS, high alloy steel, to specification
 DIN X155CrVMo12 1, BS BD2 or AISI D2

SHEETS, PLATES AND FLATS, high alloy steel, to specification DIN
 90MnCrV8

PLATES, SHEETS AND FLATS, high alloy steel, to specification
 DIN X45NiCrMo4

PLATES, high alloy steel, quenched AND tempered, having ALL of 
the following:
  (a) yield strength NOT less than 730 N/mm2;
  (b) tensile strength NOT less than 850 N/mm2;
  (c) elongation NOT less than 10%;
  (d) thickness reduction ratio during plate rolling NOT 
      less than 3:1;
  (e) plate thickness NOT less than 120 mm;
  (f) plate length NOT less than 7 200 mm;
  (g) plate mass NOT less than 18 000 kg

PLATES AND SHEET, high speed steel, but NOT including those that
 have been hollow ground OR those that have centre holes OR pin
 holes

PLATES OR SHEETS OR FLATS, high alloy steel, to specifications
 DIN 40CrMnMoS8 6, hardened and tempered

STRIPS, alloy steel, cold rolled, hardened AND tempered, having 
ALL of the following:
  (a) thickness NOT less than 0.65 mm and NOT greater than    
      8.30mm;
  (b) width NOT less 600 mm and NOT greater than 740 mm; 
  (c) chemical composition by weight of BOTH the following:
        (i) carbon content NOT less than 0.70%;
       (ii) chrome content NOT less  than 0.30%

SHEET OR PLATE, alloy steel, cold rolled, to Japanese Industrial 
Standard G 3125 (JIS G 3125), type SPA-C, thickness NOT greater 
than 2.3 mm

SHEETS, alloy steel, complying with American Society of Testing 
and Materials Standard ASTM A 463/A 463M-05 with Steel Sheet 
Designations CS, FS, DDS OR EDDS AND Coating  Designations T1-25 
OR T1-40, whether OR not in coils, having ALL of the following:
  (a) width of 630 mm, 685 mm, 699 mm, 780 mm, 790 mm, 810 mm, 
      900 mm, 914 mm, 930 mm, 990 mm, 1 000 mm, 1 025 mm,
      1 030 mm, 1 035 mm, 1 066 mm, 1 078 mm, 1 084 mm, 
      1 100 mm, 1 120 mm, 1 126 mm, 1 134 mm, 1 146 mm, 
      1 160 mm, 1 165 mm 1 170 mm, 1 195 mm, 1 200 mm, 
      1 210 mm, 1 219 mm, 1 220 mm, 1 246 mm OR 1 250 mm,  
      each having a width tolerance of + OR - 2 mm;
  (b) thickness of 0.55 mm, 0.60 mm, 0.72 mm, 0.75 mm, 0.80 mm,  
      0.90 mm, 0.96 mm, 1.00 mm, 1.15 mm, 1.20 mm, 1.50 mm, 
      1.55 mm, 1.60 mm, 1.90 mm OR 2.00 mm, each having a 
      thickness tolerance of + OR - 0.2 mm;
  (c) aluminium AND silicon coating having BOTH of the following:
        (i) aluminium content NOT less that 88%;
       (ii) weight NOT less than 20 gsm and NOT greater 
            than 90 gsm

SHEET, electrical steel, containing from 2.7% to 3.3% (both
 inclusive) by weight of silicon

ELECTRICAL STEEL, sheet and strip, cold rolled, grain oriented, as
 defined in IEC 401-1, in coil or sheet form, having a core loss
 of less than 1.5 W/kg in the long grain direction at flux density
 of 1.5 Tesla and frequency 50 Hz as determined by test methods to
 International Standard IEC 404-2

SHEETS OR STRIPS, silicon-electrical steel, grain oriented,  
cold rolled, in coil OR sheet form, having a width less than 
600 mm

SHEET, electrical steel, containing from 2.7% to 3.3% (both
 inclusive) by weight of silicon

SHEETS AND/OR STRIPS, STEEL, NON-ORIENTATED ELECTRICAL, as 
described in ANY of the following international standards:
  (a) Japanese Industrial Standard C 2552;
  (b) American Society for Testing and Materials 
      Standard A 677-05;
  (c) European Standard EN 10106

PLATES, SHEETS AND FLATS, high alloy steel, to specification DIN
 X155CrVMo12 1, BS BD2 or AISI D2

BARS, flat, having a thickness NOT exceeding 200 mm and a width NOT
 exceeding 520 mm, to ANY of the following specifications:
   (a) AISI-01;
   (b) BS 4659: 1989, in ANY of the following grades:
         (i) BA 6;
        (ii) BD 2;
       (iii) BD 2A;
        (iv) BD 6;
         (v) BO 1;
   (c) DIN 1.2101

BARS, flat, alloy steel, NOT in a hardened and tempered condition,
 having ALL of the following:
   (a) width exceeding 140 mm but NOT exceeding 460 mm;
   (b) thickness exceeding 50 mm but NOT exceeding 200 mm;
   (c) length NOT exceeding 12 m

HOOP AND STRIP, hardened and tempered, of rectangular section,
 of a thickness NOT exceeding 6 mm, of a width NOT exceeding
 500 mm and of such dimension that the thickness does NOT exceed
 one tenth of the width

STRIPS, alloy steel, cold rolled, having ALL of the following:
  (a) thickness of NOT less than 0.70 mm and NOT greater than 
      8.0 mm;
  (b) width of NOT less than 300 mm and NOT greater than 597 mm; 
  (c) strip surface designation being bright finish;
  (d) chemical composition by weight of ALL of the following:
       (i) carbon content NOT greater than 2.00%;
      (ii) chrome content NOT less than 0.30%
For the purposes of this order, tolerances allowable for 
specification (a) and (b) are:
  (a) thickness +/- 0.05 mm
  (b) width + 2 mm

STRIP, STEEL, in coils, hardened, sharpened on one or both edges,
 thickness 1.5 mm to 4 mm, width 19 mm to 50 mm

FLATS, high alloy, to specification DIN 100MnCrW4, BS B01 or AISI01

BARS, flat, to specification AISI-01, having a thickness NOT
 exceeding 100 mm or a width NOT exceeding 300 mm

WEAR BARS, EARTHMOVER BUCKET, having a Brinell hardness NOT less 
than 480

RODS, alloy steel, in coils, hot rolled, complying with 
Australian Standard AS 1444-2007, Table 1, Grade designation 
4140, having a rod diameter NOT less than 11 mm and NOT greater 
than 17 mm AND having a composition by weight of ALL of the 
following:
  (a) carbon content NOT less than 0.38% and NOT greater 
      than 0.43%;
  (b) chromium content NOT less than 0.80% and NOT greater 
      than 1.10%;
  (c) molybdenum content NOT less than 0.15% and NOT greater
      than 0.25%

RODS, in coils, alloy steel, hot rolled, having a diameter of 
NOT less than 20 mm and NOT greater than 24 mm

BARS OR RODS, high speed steel, but NOT including ANY of the
 following:
   (a) round bars OR rods having a dia of 1.60 mm or greater
       but NOT exceeding 14.00 mm;
   (b) hardened bars OR rods, of rectangular OR square
       cross-section
   For the purposes of TC 8734392 "high speed steel" means that
   it contains:
     (a) NOT less than 0.60% carbon; and
     (b)   (i) chromium; or
          (ii) vanadium; or
         (iii) cobalt; and
     (c)   (i) molybdenum and tungsten, in such percentages by
               weight that the sum of the number equal to the
               percentage of tungsten and the number equal to
               twice the percentage of molybdenum is NOT less
               than 13.5%; or
          (ii) NOT less than  7% by weight of molybdenum; or
         (iii) NOT less than 14% by weight of tungsten

BARS OR RODS, high speed steel

RODS, WELDING

BARS, flat, alloy steel, having ALL of the following:
   (a) width less than 150.0 mm;
   (b) thickness exceeding 3.25 mm but less than 50.00 mm;
   (c) length NOT exceeding 10.0 m

BARS AND/OR RODS, high alloy steel, hot rolled AND annealed, 
having a chemical composition by weight of ALL of the following:
  (a) carbon content NOT less than 0.12% and NOT greater
      than 0.18%;
  (b) silicon content NOT less than 0.10% and NOT greater
      than 0.35%;
  (c) manganese content NOT less than 0.25% and NOT greater 
      than 0.50%;
  (d) chromium content NOT less than 1.00% and NOT greater 
      than 1.40%;
  (e) molybdenum content NOT less than 0.15% and NOT greater   
      than 0.30%;
  (c) nickel content NOT less than 3.90% and NOT greater 
      than 4.30%

BARS AND/OR RODS, high alloy steel, hot rolled AND annealed, 
having a chemical composition by weight of ALL of the following:
  (a) carbon content NOT less than 0.10% and NOT greater
      than 0.16%;
  (b) silicon content NOT less than 0.10% and NOT greater 
      than 0.35%;
  (c) manganese content NOT less than 0.35% and NOT greater 
      than 0.60%;
  (d) chromium content NOT less than 0.70% and NOT greater 
      than 1.00%;
  (e) nickel content NOT less than 3.00% and NOT greater 
      than 3.75%

BARS AND RODS, high alloy, to specification DIN X153CrMoV12, 
having a chemical composition by weight of ALL of the following:
  (a) carbon content NOT less than 1.45% and NOT greater than
      1.60%;
  (b) chromium content NOT less than 11.0% and NOT greater than
      13.0%;
  (c) molybdenum content NOT less than 0.70% and NOT greater 
      than 1.00%;
  (d) vanadium content NOT less than 0.70% and NOT greater than 
      1.00%

BARS OR RODS, high alloy steel, to specifications DIN X40CrMoV51,
BS BH13 OR AISI H13, having a chemical composition by weight of 
ALL of the following:
  (a) carbon content NOT less than 0.37% and NOT greater than
      0.43%;
  (b) chromium content NOT less than 4.80% and NOT greater than
      5.50%;
  (c) molybdenum content NOT less than 1.20% and NOT greater than
      1.50%;
  (d) vanadium content NOT less than 0.90% and NOT greater than
      1.10%

BARS, HOT ROLLED, HIGH ALLOY, having BOTH of the following:
  (a) diameter NOT less than 100 mm;
  (b) molybdenum content by weight NOT less than 0.15%

BARS AND RODS, high alloy steel, to specification DIN 14NiCr14, 
having a nickel content by weight of NOT less than 3.0% and NOT 
greater than 3.5% in either of the following sizes:
   (a) less than 22 mm diameter;
   (b) greater than 82 mm diameter

BARS AND RODS, high alloy steel, to specification Material 
Number DIN 1.6587, grade EN 18CrNiMo7-6, having a chemical 
composition by weight of ALL of the following:
  (a) chromium content NOT less than 1.50% and NOT greater than
      1.80%;
  (b) molybdenum content NOT less than 0.25% and NOT greater
      than 0.35%;
  (c) nickel content NOT less than 1.40% and NOT greater than
      1.70%

BARS AND RODS, high alloy steel, to specification Material 
Number DIN 1.3401, grade DIN X120Mn12, having a manganese 
content by weight NOT less than 12.0% and NOT greater than 13.0%

BARS AND RODS, high alloy steel, to specification DIN 100Cr6, 
having a chromium content by weight of NOT less than 1.35% and 
NOT greater than 1.65%

BARS AND RODS, high alloy steel, to British Standard BS970:1991, 
grade 835M15, having a chemical content by weigh of BOTH of the 
following:
  (a) chromium content NOT less than 1.00% and NOT greater than
      1.40%;
  (b) nickel content NOT less than 3.90% and NOT greater than 
      4.30%

BARS AND RODS, high alloy steel, to specification DIN 
40CrMnNiMo8 6 4, having a chemical composition by weight of ALL 
of the following:
  (a) carbon content NOT less than 0.35% and NOT greater than
      0.45%;
  (b) chromium content NOT less than 1.80% and NOT greater than
      2.10%;
  (c) manganese content NOT less than 1.30% and NOT greater than
      1.60%;
  (d) nickel content NOT less than 0.90% and NOT greater than
      1.20%;
  (e) molybdenum content NOT less than 0.15% and NOT greater than
      0.25%

BARS OR RODS, high alloy steel, to standard SAE 4340, NOT heat 
treated OR further processed other than annealing, having a 
chemical composition by weight of ALL of the following:
  (a) carbon content NOT less than 0.38% and NOT greater than
      0.43%;
  (b) chromium content NOT less than 0.70% and NOT greater than
      0.90%;
  (c) nickel content NOT less than 1.65% and NOT greater than
      2.00%;
  (d) molybdenum content NOT less than 0.20% and NOT greater 
      than 0.30%

BARS OR RODS, high alloy steel, conforming to European 
Standard grade EN 26, NOT heat treated OR further processed 
other than annealing, having a chemical composition by weight of 
ALL of the following:
  (a) chromium content NOT less than 0.50% and NOT greater than
      0.80%;
  (b) molybdenum content NOT less than 0.45% and NOT greater
      than 0.65%;
  (c) nickel content NOT less than 2.30% and NOT greater than
      2.80%

BARS, round, high alloy steel, hot rolled, grade 38B3, having 
ALL of the following:
  (a) diameter NOT less than 25 mm and NOT greater than 65 mm;
  (b) length NOT greater than 6 m;
  (c) carbon content by weight NOT less than 0.34% and NOT 
      greater than 0.40%;
  (d) silicon content by weight NOT less than 0.10% and NOT
      greater than 0.40%;
  (e) manganese content by weight NOT less than 0.60% and NOT
      greater than 0.90%

BARS OR RODS, high alloy steel, conforming to International 
Material No. 1.6582, Specification 34CrNiMo6, having a chemical 
composition by weight of ALL of the following:
  (a) chromium content NOT less than 1.30% and NOT greater than
      1.70%;
  (b) nickel content NOT less than 1.30% and NOT greater than
      1.70%;
  (c) molybdenum content NOT less than 0.15% and NOT greater than
      0.30%

BARS OR RODS, high alloy steel, to specifications DIN 40CrMnMoS8 
6, hardened and tempered, having a chemical composition by 
weight of ALL of the following:
  (a) carbon content NOT less than 0.35% and NOT greater than
      0.45%;
  (b) chromium content NOT less than 1.80% and NOT greater than
      2.20%;
  (c) manganese content NOT less than 1.40% and NOT greater 
      than 1.60%;
  (d) molybdenum content NOT less than 0.15% and NOT greater than
      0.25%;
  (e) sulphur content NOT less than 0.05% and NOT greater than
      0.10%

BARS, alloy steel, round, diameter NOT exceeding 500 mm, to ANY
of the following specifications:
   (a) AISI-01, having a tungsten content NOT less than 0.40%
       and NOT greater than 0.60%;
   (b) AISI-B.01, having a tungsten content NOT less than 0.40%
       and NOT greater than 0.60%;
   (c) AISI-B.D2, having a chromium content NOT less than 11.0%
       and NOT greater than 12.5%;
   (d) AISI-B.D3, having a chromium content NOT less than 11.0%
       and NOT greater than 13.0%;
   (e) AISI-B.A6, having a chromium content NOT less than 0.85% 
       and NOT greater than 1.15% AND a molybdenum content NOT
       less than 1.20% and NOT greater than 1.60%

BARS, STEEL, HIGH ALLOY, hot rolled, round, having BOTH the 
following:
  (a) sulphur content NOT exceeding 0.005%;
  (b) phosphorus content NOT exceeding 0.010%

BARS OR RODS, high alloy steel, grades 8620 or 8620H or SNCM220 
or SNCM220H, having a chemical composition by weight of ALL of 
the following:
  (a) Carbon     -  0.17% to 0.23% (both inclusive);
  (b) Silicon    -  0.10% to 0.35% (both inclusive);
  (c) Manganese  -  0.60% to 0.95% (both inclusive);
  (d) Chromium   -  0.35% to 0.65% (both inclusive);
  (e) Molybdenum -  0.15% to 0.30% (both inclusive);
  (f) Nickel     -  0.35% to 0.75% (both inclusive)

BARS AND RODS, round, hot rolled, high alloy steel, complying
 with AMS (Aerospace Material Specification) 6418F

THREAD BARS, alloy steel, having ALL of the following: 
  (a) hot rolled;
  (b) continuous course right hand thread;
  (c) screwable along entire length;
  (d) cold stretched;
  (e) stress relieved;
  (f) diameter NOT less than 26 mm and NOT greater than 80 mm
  (g) yield strength NOT less than 850 MPa

BARS, GROUSER, hot rolled alloy steel, to specification EN10083-
3, having a chemical composition by weight of ALL of the 
following:
  (a) carbon content NOT less than 0.24% and NOT greater than
      0.42%;
  (b) manganese content NOT less than 1.10% and NOT greater than
      1.70%;
  (c) chromium content NOT less than 0.30% and NOT greater than
      0.60%;
  (d) boron content NOT less than 0.0008% and NOT greater than
      0.0050%

BARS AND RODS, low alloy, to specification DIN 62SiMnCr4, having 
a chemical composition by weight of ALL of the following:
  (a) carbon content NOT less than 0.58% and NOT greater than
      0.66%;
  (b) silicon content NOT less than 0.90% and NOT greater than
      1.20%;
  (c) manganese content NOT less than 0.90% and NOT greater than
      1.20%;
  (d) chromium content NOT less than 0.40% and NOT greater than 
      0.70%

BARS, FLAT, alloy steel, having ALL of the following:
   (a) width NOT exceeding 460 mm;
   (b) thickness NOT exceeding 100 mm;
   (c) length NOT exceeding 10 m

BARS, alloy steel, flat, complying with European Standard, 
International Organization for Standardization (EN ISO) 
4957:1999, Table 6, Steel name X38CrMoV5-3

BARS, round, forged, alloy steel, having a diameter NOT less 
than 200 mm

BARS OR RODS, high alloy steel, to specification DIN 40CrMnNiMo8 6 4

BARS, flat, alloy steel, having ALL of the following:
   (a) width less than 150.0 mm;
   (b) thickness exceeding 3.25 mm but less than 50.00 mm;
   (c) length NOT exceeding 10.0 m

BARS, alloy steel, round, diameter NOT exceeding 500 mm, to ANY of
 the following specifications:
   (a) AISI-01;
   (b) AISI-B.01;
   (c) AISI-B.D2;
   (d) AISI-B.D3;
   (e) AISI-B.A6;
   (f) AISI-D.K4

BARS AND RODS, high alloy steel, complying with European 
Standard EN 10085:2001, Designation: Steel name 41CrAlMo7-10 OR 
Steel number 1.8509

BARS, flat, alloy steel, having ALL of the following:
   (a) width less than 150.0 mm;
   (b) thickness exceeding 3.25 mm but less than 50.00 mm;
   (c) length NOT exceeding 10.0 m

BARS AND RODS, high alloy steel, having a chemical composition by
 weight of ALL of the following:
   (a) carbon     - 1.10%;
   (b) silicon    - 0.90%;
   (c) manganese  - 0.40%;
   (d) chromium   - 8.30%;
   (e) molybdenum - 2.10%;
   (f) vanadium   - 0.50%;
   (g) + aluminium;
   (h) + niobium

BARS OR RODS, high alloy steel, to specifications DIN X40CrMoV51,
BS BH13 OR AISI H13, having a chemical composition by weight of 
ALL of the following:
  (a) carbon content NOT less than 0.37% and NOT greater than
      0.43%;
  (b) chromium content NOT less than 4.80% and NOT greater than
      5.50%;
  (c) molybdenum content NOT less than 1.20% and NOT greater than
      1.50%;
  (d) vanadium content NOT less than 0.90% and NOT greater than 
      1.10%

BARS AND RODS, high alloy, to specification DIN 60WCrV7, having 
a chemical composition by weight of ALL of the following:
  (a) carbon content NOT less than 0.55% and NOT greater than 
      0.65%;
  (b) chromium content NOT less than 0.90% and NOT greater than
      1.20%;
  (c) vanadium content NOT less than 0.10% and NOT greater than
      0.20%;
  (d) tungsten content NOT less than 1.80% and NOT greater than 
      2.10%

BARS OR RODS, high alloy steel, annealed AND peeled, complying 
with British Standard 970-3:1991 (BS 970-3:1991) Grade 655M13, 
having ALL of the following:
  (a) sulphur AND phosphorous content NOT greater than 0.01%;
  (b) molybdenum content NOT greater than 0.20%;
  (c) grain size number NOT less than 6.0, complying to American
      Society for Testing and Materials Standard E112-13 
      (ASTM E112-13);
  (d) American Society for Testing and Materials Standard E381-
      01 (ASTM E381-01), ratings NOT greater than S1, R1 OR C1;
  (e) German Institute of Standardisation 50 602 (DIN 50 602) 
      K4 index NOT greater than 20

THREAD BARS, alloy steel, having ALL of the following:
  (a) hot rolled;
  (b) continuous course left hand thread;
  (c) screwable along entire length;
  (d) diameter NOT less than 36 mm and NOT greater than 80 mm;
  (e) yield strength NOT less than 500 MPa and NOT greater than
      700 MPA

THREAD BARS, alloy steel, having ALL of the following: 
  (a) hot rolled;
  (b) continuous course right hand thread;
  (c) screwable along entire length;
  (d) cold stretched;
  (e) stress relieved;
  (f) diameter NOT less than 26 mm and NOT greater than 80 mm
  (g) yield strength NOT less than 830 MPa

BARS AND/OR RODS, silver steel, complying with BS1407, having 
BOTH of the following:
  (a) spherical;
  (b) diameter NOT less than 1 mm and NOT greater than 55 mm

STEEL, ROCK DRILL, hollow

DRILL BARS AND RODS, hollow, external cross-section dimension
 exceeding 15 mm but NOT exceeding 52 mm, threaded or tapered

WIRES, WELDING, silico manganese steel, electroplated

WIRE, WELDING, silico-manganese steel

WELDING WIRE, solid metal inert gas, to ANY of the following
 British Standards or their equivalents:
   (a) BS2901/Part 1 - A30;
   (b) BS2901/Part 1 - A31;
   (c) BS2901/Part 1 - A32;
   (d) BS2901/Part 1 - A33;
   (e) BS2901/Part 1 - A34

WIRE, silicon chrome spring steel

WIRE, piano, bright, tinned or polished, but NOT including bright
 wire having a dia of 0.234 mm or greater but NOT exceeding
 3.658 mm

WIRE, FASTENER, cold heading quality alloy steels, diameter NOT 
less than 12 mm, in ANY of the following grades:
  (a) 10B21;
  (b) 10B40;
  (c) 51B37;
  (d) 51B40

WIRE, WELDING