Tariff Concession Orders

STEAM GENERATORS, EMISSION CONTROL, having ALL of the following
  (a) length NOT less than 3.8 metres;
  (b) width AND height NOT less than 1.6 metres;
  (c) weight NOT less than 4.0 tonnes

STEAM GENERATORS, containerised, complying with Det Norske 
Veritas Standard DNV 2,7-2, including ALL of the following:
  (a) steam capacity NOT greater than 6.00 Mbtu per hour;
  (b) maximum allowable operating pressure NOT greater than 
      150 psig;
  (c) auxiliary container

STEAM GENERATED HUMIDIFIERS, electric, having an output NOT less 
than 1 kg/h and NOT greater than 130 kg/h

VAPOUR GENERATORS, CONCRETE CURING, including ALL of the 
following:
  (a) stainless steel combustion chamber having BOTH of the 
      following:
         (i) jacket;
        (ii) directly fired heating,
  (b) inlets;
  (c) rotary lobe compressor, including BOTH of the following:
         (i) working pressure NOT greater than 601 mbar;
        (ii) pressure regulator AND/OR safety valve,
  (d) control panel AND/OR display;
  (e) flame controller;
  (f) valves;
  (g) pipes AND/OR tubes AND/OR hoses;
  (h) mixer AND/OR burner

BIOMASS FIRED BOILER PLANT, programmable logic controlled, 
including ALL of the following:
  (a) stokers;
  (b) fans;
  (c) pumps;
  (d) valves;
  (e) grit collectors;
  (f) fuel hoppers;
  (g) controls;
  (h) conveyors;
  (i) stairs AND platforms,
with OR without ducting AND/OR stack

STEAM GENERATORS, three pass, wet back, self-contained, with OR 
without steam hose AND fittings, complying with Standard DNV 
2.7-1 AND DNV 2.7-2, having ALL of the following:
  (a) saturated steam flow NOT less than 2 000 kg/hr;
  (b) capacity NOT less than 4.5 million BTU;
  (c) fire detection AND suppression unit;
  (d) gas detection unit;
  (e) hydrocarbon detection unit;
  (f) internal spark arrestor;
  (g) remote emergency shutdown function

BIOMASS BOILERS, HEATING FLUID, thermal power NOT less than 
350 kW and NOT greater than 30 000 kW, having two OR more of the 
following:
  (a) chimney;
  (b) chutes;
  (c) conveyor;
  (d) surge bin;
  (e) filters;
  (f) controls;
  (g) gears;
  (h) motors;
  (i) fans

GENERATORS, PURE STEAM, stainless steel construction, including 
ALL of the following:
  (a) separator columns;
  (b) valves;
  (c) sensors

HOT WATER BOILER PLANT, solid biomass having wet base moisture 
content exceeding 40%, programmable logic controlled, including 
ALL of the following:
  (a) furnace;
  (b) boiler;
  (c) cleaning AND ash removal;
  (d) fuel feeding;
  (e) emission control;
  (f) combustion grates
  (g) particulate output NOT greater than 200 mg/m3N db at 12%  
      CO2;
  (h) carbon monoxide output NOT greater than 100 mg/m3N db at 
      12% CO2;
  (i) nitrogen oxides output NOT greater than 300 mg/m3N db at 
      12% CO2

BOILERS, OXYFUEL, consisting of ALL of the following:
  (a) absorbers;
  (b) actuators;
  (c) burners;
  (d) controllers;
  (e) dampers;
  (f) ducts;
  (g) fans;
  (h) heat exchangers;
  (i) heaters;
  (j) mist separators;
  (k) motors;
  (l) pumps;
  (m) water feeders;
  (n) water removers

PARTS, SUPER HEATED WATER BOILER, being ANY of the following:
  (a) upper bank panels;
  (b) steam header;
  (c) vent pipeline;
  (d) pipes AND beams

PARTS, LIQUOR RECOVERY BOILER, being sidewall riser pipes

NOZZLE GRIDS, FLUIDISED BED BOILER, whether OR not assembled, 
including ALL of the following:
  (a) primary air intakes;
  (b) expansion joints AND/OR expansion pipes;
  (c) distribution pipes having nozzles

PARTS, LIQUOR RECOVERY BOILER, being seamless carbon steel 
sidewall riser pipes, having a maximum working pressure NOT less 
than 60 barG with a maximum working temperature NOT less than 
250 degrees Celsius

PARTS, SUPERHEATER WATER CO-GENERATION BOILER, being ANY of the 
following:
  (a) boiler membrane tube walls AND/OR panels;
  (b) downcomer tubes;
  (c) water wall headers

PARTS, STEAM GENERATION BOILER, operating pressure NOT less than 
4 000 kPa, steam capacity NOT less than 100 t/hr, being ANY of 
the following: 
  (a) furnace air cast nozzle; 
  (b) air port rodders; 
  (c) air registers with OR without air rodder assembly kits; 
  (d) air duct subassembly kits with OR without air dumpers; 
  (e) air duct access door; 
  (f) tube assembly OR assembly kits, being ANY of the
      following: 
            (i) floors; 
           (ii) panels; 
          (iii) walls, 
  (g) air ports with OR without air rodder assembly kits; 
  (h) furnace walls AND walls assembly kits; 
  (i) pitot tube; 
  (j) thermoelement

PARTS, STEAM GENERATION BOILER, operating pressure NOT less than 
4 000 kPa, steam capacity NOT less than 30 t per hour, being ANY 
of the following:
  (a) boiler tube coils;
  (b) heat shields;
  (c) flow restriction insert

PARTS, SUPER-HEATED WATER BOILER, being a boiler drum having ALL 
of the following:
  (a) boiler feed pipe;
  (b) demister unit;
  (c) semi-ellipsoidal dished ends with manholes;
  (d) working pressure NOT greater than 10.395 MPa;
  (e) operating temperature NOT less than 314 degrees C

PARTS, STEAM GENERATOR, POWER GENERATION PLANT, being ANY of the 
following:
  (a) inlet transition duct unit;
  (b) inlet plenum;
  (c) exhaust hood unit;
  (d) stack adapter;
  (e) exhaust stack unit;
  (f) once through steam generator AND ducting erection joint
      assembly kits, consisting of BOTH of the following:
         (i) sheet metal sealing strips AND fastenings;
        (ii) insulation,
  (g) piping, valves AND instrumentation consisting of ALL of 
      the following: 
         (i) high pressure AND low pressure vent stack;
        (ii) high pressure steam outlet piping;
       (iii) low pressure steam outlet piping;
        (iv) pilot-operated relief valve piping;
         (v) high pressure feedwater inlet piping;
        (vi) low pressure feed water inlet piping

WATER BOILERS, having ALL of the following: 
  (a) working pressure NOT greater than 3 bar ;
  (b) maximum working temperature NOT less than 
      105 degrees Celsius; 
  (c) thermometer; 
  (d) pressure gauge; 
  (e) drain valve; 
  (f) condenser;
  (g) internal capacity NOT greater than 19 000 litres

BOILERS, hydronic, condensing, including ALL of the following:
  (a) natural OR liquid petroleum gas operation;
  (b) gas consumption NOT less than 75 MJ/h and NOT greater than
      400 MJ/h;
  (c) output NOT less than 18 kW and NOT greater than 100 kW;
  (d) stainless steel heat exchanger;
  (e) built-in circulator pump AND expansion tank AND air 
      bleeders

BOILERS, condensing, indoor, having ALL of the following:
  (a) natural OR liquid petroleum gas operation;
  (b) gas consumption NOT less than 75 MJ/h and NOT
      greater than 150 MJ/h;
  (c) output NOT less than 18 kW and NOT greater than 37 kW;
  (d) aluminium heat exchanger

BIOMASS BOILERS, HEATING FLUID, thermal power NOT less than 90 
kW and NOT greater than 26 000 kW, having two OR more of the 
following:
  (a) chimney; 
  (b) chutes; 
  (c) conveyor; 
  (d) surge bin;
  (e) filters; 
  (f) controls; 
  (g) gears; 
  (h) motors; 
  (i) fans

PARTS, BOILER POWER PLANT, being EITHER of the following: 
  (a) de-superheaters;
  (b) de-superheating system, pressure reduction, including 
      ALL of the following:
           (i) de-superheater;
          (ii) steam inlet;
         (iii) steam outlet

AUXILIARY PLANT, STEAM GENERATION BOILER, comprising ANY of the 
following:
  (a) windboxes;
  (b) superheaters, preheaters or airheaters;
  (c) sootblowers;
  (d) attemperators
  (e) ash handlers;
  (f) deaerators;
  (g) coal bunkers

CONDENSERS, HEAT TRANSFER FLUID, having ALL of the following
  (a) length NOT less than 7.0 metres;
  (b) width AND height NOT less than 3.2 metres; 
  (c) weight NOT less than 22.0 tonnes

CONDENSERS, STEAM, POWER STATION, WATER COOLED

PARTS, ROTARY HEAT EXCHANGER, being air pre-heater baskets

PARTS, REGENERATIVE AIR HEATER, being ANY of the following:
  (a) seal frame;
  (b) seal shoe AND/OR wear shoe;
  (c) collar seal;
  (d) thermal compensator

PARTS, RECOVERY BOILER ECONOMISER, SOOTBLOWER AND ASH HANDLING 
SYSTEM, being ALL of the following:
  (a) tube and header;
  (b) casing including buckstays AND insulation frame;
  (c) access door;
  (d) flue gas duct;
  (e) flue gas expansion bellows

PARTS, RECOVERY BOILER ECONOMIZER, being ALL of the following:
  (a) tube and economizer header, having a maximum working
      pressure NOT less than 70 barG with a maximum working
      temperature NOT less than 270 degrees Celsius;
  (b) economizer enclosure casing AND buckstays AND insulation
      frame, having a maximum working temperature NOT less than 
      170 degrees Celsius;
  (c) access door, having a maximum working temperature NOT less
      than 350 degrees Celsius;
  (d) flue gas duct, having a maximum working temperature NOT
      less than 170 degrees Celsius;
  (e) flue gas expansion bellows, having a maximum working
      temperature NOT less than 170 degrees Celsius

HEADERS, WATER BOILER STEAM DISTRIBUTING, having a maximum 
working pressure of NOT less than 10.395 MPa

PARTS, BOILER FURNACE, being iron AND/OR steel tubular panels

PARTS, AUXILIARY PLANT, POWER STATION STEAM GENERATION BOILER, 
being ANY of the following:
  (a) hangers;
  (b) manifolds;
  (c) walls;
  (d) tubes;
  (e) supports;
  (f) straps;
  (g) separators;
  (h) tanks;
  (i) coils;
  (j) casings;
  (k) frames;
  (l) roofs;
  (m) floors;
  (n) noses;
  (o) blocks;
  (p) bellows

PARTS, AUXILIARY PLANT, POWER STATION STEAM GENERATION BOILER, 
being ANY of the following:
  (a) ducting panels;
  (b) ducting boxes;
  (c) ducting vanes;
  (d) ducting supports;
  (e) stiffeners;
  (f) trusses;
  (g) pulverised fuel pipes and/or fittings;
  (h) boiler and/or ducting access doors and/or fittings

PARTS, AUXILIARY PLANT, STEAM GENERATION BOILER, NOT less than 
2 230 tonnes per hour comprising ANY of the following:
  (a) hangers;
  (b) manifolds;
  (c) walls;
  (d) tubes;
  (e) supports;
  (f) straps;
  (g) separators;
  (h) tanks;
  (i) coils;
  (j) silencers;
  (k) casings;
  (l) frames;
  (m) dampers;
  (n) expansion joints;
  (o) roofs;
  (p) floors;
  (q) noses;
  (r) blocks;
  (s) bellows

GENERATORS, hydrogen gas

GENERATORS, HYDROGEN AND OXYGEN GAS, with OR without
interconnecting piping, including ALL of the following:
  (a) electrolyser;
  (b) chiller;
  (c) control cabinet;
  (d) water tank;
  (e) transformer

HYDROGEN PEROXIDE VAPOUR GENERATING MACHINES

GENERATORS, HYDROGEN AND OXYGEN GAS, skid mounted

PARTS, STEAM REFORMER, being ANY of the following:
  (a) bull tees; 
  (b) cones AND/OR cone assemblies;
  (c) catalyst tubes whether OR not assembled;
  (d) outlet manifolds AND/OR headers whether OR not assembled;
  (e) inlet AND/OR outlet pigtails;
  (f) constant effort spring hanger whether OR not assembled

PARTS, HYDROGEN GENERATOR REFORMER, being ANY of the following:
  (a) catalyst tubes whether OR not assembled;
  (b) outlet cones;
  (c) outlet headers

ENGINES, being original equipment or reproductions of goods fitted
 as original equipment to vehicles having BOTH of the following:
   (a) if imported, would fall within Chapter 87 of the Customs
       Tariff Act 1987;
   (b) manufactured before 1963

ENGINES, petrol, having a piston displacement exceeding 6.5 L,
 but NOT including petrol engines imported with gearboxes OTHER
 THAN gearboxes admissible under Item 50 by virtue of a Commercial
 Tariff Concession Order classified under subheading 8483.40 or
 subheading 8708.40

ENGINES, petrol, four-stroke, horizontal shaft, having a power NOT
 exceeding 4.5 kW

ENGINES, petrol, two-stroke, having BOTH the following:
   (a) engine capacity less than 34 cc;
   (b) weight less than 3.75 kg

ENGINES, vertical shaft, reciprocating, four-stroke

ENGINES, diesel, but NOT including diesel engines imported with
 ANY of the following:
   (a) gearboxes, OTHER THAN gearboxes admissable under Item 50
       by virtue of a Commercial Tariff Order;
   (b) power take-offs, OTHER THAN power take-offs admissable
       under Item 50 by virtue of a Commercial Tariff Order;
   (c) radiators

ENGINES, OFF HIGHWAY REAR DUMP TRUCK, diesel, having ALL of the 
following:
  (a) turbo charged;
  (b) V-12 cylinder configuration;
  (c) capacity NOT less than 27 L;
  (d) net rated power output NOT less than 550 kW

ENGINES, DIESEL, flywheel power of 1 000 kW OR greater

INJECTORS, FUEL, but NOT including ANY of the following:
                                            Fuel       Coil
 Type   Q Stat     Q Dyne           TI      Pressure   Resistance
 1.3A   198 ccm/m  3.95 ccm/1 000   2.0 MS  3.0 bar    15.9 ohms
                           strokes
 EV1.3A 170 ccm/m  3.6 ccm/1 000    2.0 MS  2.5 bar    15.9 ohms
                           strokes
 EV1.3A 170 ccm/m  5.19 ccm/1 000   2.5 MS  2.5 bar    15.9 ohms
                           strokes
 EV1.3A 250 ccm/m  5.81 ccm/1 000   2.2 MS  3.3 bar    15.9 ohms
                           strokes
 EV1.3C 206 ccm/m  4.44 ccm/1 000   2.0 MS  3.0 bar    14.5 ohms
                           strokes

PARTS, AUTOMOTIVE ENGINE, being piston rings, side ground but
 NOT further worked

CARBURETTORS, marine outboard

PISTON BLANKS, forged aluminium, unmachined

CARBURETTORS, LIQUID FUEL

PARTS, ENGINE, piston displacement of 75 cc OR greater but NOT
 exceeding 150 cc, power output of 4.5 kW OR greater, being ANY
 of the following:
   (a) connecting rods;
   (b) cylinder heads;
   (c) cylinder blocks (barrels, crankcases);
   (d) cylinder liners;
   (e) pistons;
   (f) piston pins (gudgeon pins);
   (g) piston rings;
   (h) reed valves;
   (i) reed valve blocks;
   (j) rotary valves

PARTS, PASSENGER MOTOR VEHICLE, manufactured at least 30 years
 before the goods are entered for home consumption, OR reproductions
 of these parts, being ANY of the following:
   (a) cam followers;
   (b) cam thrust buttons;
   (c) camshaft lock plates;
   (d) camshaft spacer buttons;
   (e) carburettors;
   (f) con rods;
   (g) floats;
   (h) float chamber lids;
   (i) float chambers;
   (j) float needle seatings;
   (k) fuel pump block off plates;
   (l) inlet manifolds;
   (m) jets;
   (n) lifters;
   (o) liners, piston;
   (p) manifolds;
   (q) needles;
   (r) piston guide keys;
   (s) rocker arm kits, including ALL of the following:
         (i) rocker arms;
        (ii) fulcrums;
       (iii) adjusting nuts;
   (t) rocker arms;
   (u) rocker shafts;
   (v) valve guides;
   (w) valve seats;
   (x) valves;
   (y) welsh plugs;

FOLLOWERS, CAMSHAFT (ALSO KNOWN AS LIFTERS), PUSHROD ENGINE, but NOT
 including followers, overhead camshaft engine

PARTS, CHAINSAW ENGINE, being piston rings

GUIDES, timing chain, automotive engine

POWERHEAD CARBURETTOR PARTS, being ANY of the following:
   (a) fixed jet;
   (b) top cover;
   (c) cup plug;
   (d) inlet needle;
   (e) inlet lever;
   (f) spindle;
   (g) metering diaphragm;
   (h) valve jet;
   (i) adjuster;
   (j) throttle shaft with lever;
   (k) throttle shutter;
   (l) choke shaft with lever;
   (m) choke shutter;
   (n) pump diaphragm;
   (o) bottom cover;
   (p) retainer;
   (q) clip

PISTONS, SPARK IGNITION INTERNAL COMBUSTION ENGINE, cast, with 
OR without piston rings AND/OR gudgeon pins

VALVES, INTERNAL COMBUSTION ENGINE, inlet OR exhaust

VALVES, inlet or exhaust, diesel engine, having a dimension
 exceeding ANY of the following:
   (a) head dia 50 mm;
   (b) stem dia 13 mm;
   (c) ground parallel stem length 175 mm

PARTS, DIESEL ENGINE, being ANY of the following:
   (a) anchorages, flywheel housing;
   (b) arms, lifting, cylinder block;
   (c) arms, rocker, cylinder head;
   (d) baffles, lubricating;
   (e) bands, tensioner, lubricating;
   (f) blocks, cylinder;
   (g) bushings, piston connecting rod;
   (h) caps, breather, engine mounting;
   (i) caps, cylinder block;
   (j) caps, cylinder head;
   (k) caps, induction;
   (l) caps, oil filler, lubricating;
   (m) casings, auxilliary drive gear;
   (n) casings, cylinder block;
   (o) clamps, lubricating;
   (p) covers, cylinder block;
   (q) covers, inspection, cylinder block;
   (r) covers, lubricating;
   (s) covers, smoke eliminator;
   (t) covers, thermostat;
   (u) diaphragms, smoke eliminator;
   (v) dipsticks, oil, lubricating;
   (w) eliminators, smoke;
   (x) flanges, lubricating;
   (y) gratings, induction;
   (z) guides, exhaust valve, cylinder head;
  (aa) guides, intake valve, cylinder head;
  (ab) heads, cylinder;
  (ac) housings, thermostat;
  (ad) indicators, setting, engine mounting;
  (ae) intakes, air, induction;
  (af) kits, repair, cylinder head, comprising ALL of the following:
          (i) sleeves;
         (ii) o-rings;
        (iii) sealing rings;
  (ag) lines, leak-off, fuel pipe;
  (ah) locks, cylinder head;
  (ai) manifolds, induction, cylinder block;
  (aj) manifolds, union, cylinder block;
  (ak) manifolds, union, induction;
  (al) pipes, connecting, radiator;
  (am) pipes, cylinder block;
  (an) pipes, exhaust, cylinder block;
  (ao) pipes, fuel delivery;
  (ap) pipes, injection, fuel;
  (aq) pipes, lubricating;
  (ar) pipes, oil cooler;
  (as) pipes, oil filler, lubricating;
  (at) pipes, oil transfer, lubricating;
  (au) pipes, oil, lubricating;
  (av) pipes, oil, with strainer housing, lubricating;
  (aw) pipes, pressure oil, lubricating;
  (ax) pipes, suction, lubricating;
  (ay) pipes, water, cooling;
  (az) plates, anchorage, lubricating;
  (ba) plates, attaching, flywheel housing;
  (bb) plates, baffle, lubricating;
  (bc) plates, splash, cylinder block;
  (bd) plugs, cylinder block;
  (be) plugs, lubricating;
  (bf) plugs, protecting, cylinder block;
  (bg) rods, control, smoke eliminator;
  (bh) rods, piston, connecting;
  (bi) seats, exhaust valve, cylinder head;
  (bj) seats, intake valve, cylinder head;
  (bk) seats, lubricating;
  (bl) senders, pressure, cylinder block;
  (bm) shims, flywheel housing;
  (bn) sleeves, cylinder head;
  (bo) sleeves, engine mounting;
  (bp) sleeves, spacer, cylinder block;
  (bq) sumps, oil, lubricating;
  (br) tubes, extension, dipstick;
  (bs) valves, exhaust, cylinder head;
  (bt) valves, inlet, cylinder head

MANIFOLDS, AIR INTAKE, DIESEL ENGINE, aluminium

PARTS, DIESEL ENGINE, being ANY of the following:
    (a) adapter, oil pan;
    (b) connection, adapter;
    (c) connection, air crossover;
    (d) connection, exhaust;
    (e) connection, exhaust outlet;
    (f) connection, fuel block;
    (g) connection, lube oil suction;
    (h) connection, oil filter;
    (i) connection, oil suction;
    (j) connection, oil supply;
    (k) connection, oil transfer;
    (l) connection, turbo oil drain;
    (m) connection, vent;
    (n) connection, water inlet;
    (o) connection, water outlet;
    (p) connection, water transfer;
    (q) cover, access hole;
    (r) cover, aftercooler;
    (s) cover, camshaft;
    (t) cover, gear;
    (u) cover, hand hole;
    (v) cover, rocker lever;
    (w) cover, valve;
    (x) cover, water header;
    (y) crosshead, valve;
    (z) guard, belt;
   (aa) guard, fan;
   (ab) housing, cam follower;
   (ac) housing, flywheel;
   (ad) housing, gear;
   (ae) housing, rocker lever;
   (af) housing, thermostat;
   (ag) kit, rear engine power take off, incorporating:
           (i)(a) bearing;
              (b) bearing/spacer;
              (c) coupling;
              (d) capscrew and washer;
              (e) cover plate;
              (f) cover;
              (g) drive gear;
              (h) flywheel housing;
              (i) gasket;
              (j) output shaft and gear;
              (k) idler gear;
              (l) mounting hardware;
              (m) nut;
              (n) hose;
              (o) o-ring;
              (p) cup plug;
              (q) pipe plug;
              (r) seal;
              (s) drive/idler shaft;
              (t) washer, or
          (ii)(a) drive gear;
              (b) bearing;
              (c) bearing carrier;
              (d) coupling;
              (e) capscrew and washer;
              (f) idler gear;
              (g) o-ring;
              (h) retaining plate;
              (i) spring and ball;
              (j) silencer gear;
              (k) drive/idler shaft;
              (l) spacer;
              (m) snap ring;
   (ah) lever, cam follower;
   (ai) manifold, fuel;
   (aj) manifold, oil;
   (ak) manifold, water;
   (al) nozzle, piston cooling;
   (am) pin, cam follower;
   (an) pin, piston;
   (ao) pin, tappet roller;
   (ap) rod, engine connecting;
   (aq) roller, cam follower;
   (ar) roller, tappet;
   (as) shaft, rocker lever;
   (at) spacer, crankshaft;
   (au) spacer, fan;
   (av) spacer, fan pilot;
   (aw) spacer, mounting;
   (ax) support, alternator;
   (ay) support, bearing;
   (az) support, camshaft thrust;
   (ba) support, engine;
   (bb) support, fan;
   (bc) support, fuel pump;
   (bd) support, oil cooler;
   (be) support, pivot shaft;
   (bf) support, thermostat housing

PARTS, DIESEL ENGINE, being ANY of the following:
   (a) pistons having a diameter NOT less than 83 mm;
   (b) piston assemblies, comprising a piston having a diameter NOT
       less than 83 mm, pin and with OR without piston rings;
   (c) cylinder sleeves with an inside diameter NOT less than 83 mm;
   (d) cylinder sleeve assemblies, comprising a sleeve with an inside
       diameter NOT less than 83 mm, piston, piston ring and pin

PARTS, DIESEL ENGINE, being ANY of the following:
   (a) belt tensioner;
   (b) vibration damper;
   (c) crankshaft adapter;
   (d) engine brake;
   (e) after cooler;
   (f) after cooler core

FLYWHEEL HOUSINGS, DIESEL ENGINE, precast metal

PARTS, DIESEL ENGINE, being ANY of the following:
   (a) gear housing;
   (b) gear cover

PARTS, DIESEL ENGINE, being ANY of the following:
   (a) rocker lever;
   (b) push rod;
   (c) rocker lever support

OIL PANS, DIESEL ENGINE, pressed steel or precast with a holding
 capacity of NOT less than 10 litres

EXHAUST MANIFOLDS, DIESEL ENGINE, with a final outlet port diameter
 of NOT less than 76 mm OR a final outlet port cross-section area
 NOT less than 45 square cms

PARTS, DIESEL ENGINE, being ANY of the following:
   (a) cylinder blocks with a piston bore diameter NOT less than
       83 mm;
   (b) cylinder heads for cylinder blocks with a piston bore
       diameter NOT less than 83 mm and an engine capacity
       greater than 5 L, but NOT including cylinder heads with
       pre-combustion chambers
 For the purpose of this order, ALL measurements have a tolerance of
 + OR - 5%

CYLINDER SLEEVE KITS, DIESEL ENGINE, comprising a sleeve with an
 inside diameter NOT less than 83 mm (+ OR - 5%), and seals to match

OVERHAUL KITS, DIESEL ENGINE HAVING A CAPACITY OF 8 LITRES OR
 GREATER, comprising ALL of the following:
   (a) cylinder kits, comprising ALL of the following:
          (i) pistons;
         (ii) rings;
        (iii) cylinder liners;
         (iv) liner O-rings;
          (v) piston pins,
   (b) conrod bearings;
   (c) main bearings;
   (d) gaskets

PISTON RINGS, DIESEL ENGINE

TURBINES, HYDRAULIC, DOWNHOLE, OIL AND GAS, comprising ALL of 
the following;
  (a) rotors;
  (b) stators;
  (c) rotor shafts;
  (d) face seals;
  (e) alternators

HYDRO TURBINES, hydraulic, including ALL of the following;
  (a) power output NOT less than 1 000 kW, and NOT greater than
      10 000 kW;
  (b) pelton runner;
  (c) bypass line;
  (d) pressure gauges;
  (e) jet deflector;
  (f) needle nozzle control

PARTS, HYDRAULIC TURBINE, being ANY of the following:
  (a) operating rings;
  (b) top covers;
  (c) guide vane handles, links AND/OR levers;
  (d) pivot rings;
  (e) pivot ring supports; 
  (f) adaptor plate pivot rings; 
  (g) draft tube link cones

PARTS, HYDRAULIC TURBINE, assembled OR unassembled, being ANY of 
the following:                 
  (a) guide vane housings;  
  (b) bearings;  
  (c) rings;  
  (d) seals

PARTS, HYDRAULIC TURBINE, being thrust blocks

PARTS, HYDRAULIC TURBINE, being upper AND/OR lower draft 
tube cones

PARTS AND/OR ASSEMBLIES, MUD MOTORS, DOWNHOLE, comprising ANY of 
the following:
   (a) housings;
   (b) adapters;
   (c) rotors;
   (d) rotor catchers;
   (e) stators;
   (f) protectors and/or stabilisers;
   (g) protector pads;
   (h) mandrels;
   (i) covers;
   (j) nozzles;
   (k) spacers;
   (l) bypass pistons;
   (m) rings;
   (n) caps;
   (o) couplings;
   (p) shims;
   (q) sleeves;
   (r) bearings;
   (s) thrust pads;
   (t) shafts;
   (u) retainers;
   (v) power sections;
   (w) dump subs;
   (x) pick up subs;
   (y) jet subs;
   (z) upper saver subs;
  (aa) adjustable housing assemblies;
  (ab) jet sub assemblies;
  (ac) dump sub assemblies;
  (ad) constant velocity (CV) sub-assemblies

PARTS, HYDRAULIC TURBINE, being ANY of the following:
  (a) spiral casings;
  (b) stay ring and vanes;
  (c) spiral casing inlet and/or access pieces;
  (d) head covers;
  (e) bottom covers;
  (f) upper draft tube liners;
  (g) pit liners;
  (h) guide vanes;
  (i) guide rings;
  (j) guide vane arms;
  (k) guide vane connecting rods;
  (l) bearing supports;
  (m) oil basins;
  (n) shaft packing cases;
  (o) spiral casing foundations;
  (p) main shafts;
  (q) coupling covers;
  (r) runners;
  (s) guide vane hydraulic cylinders;
  (t) penstock end pipes;
  (u) dismantling joints;
  (v) control piping

PARTS, HYDRO ELECTRIC TURBINE, being ANY of the following:
  (a) runners;
  (b) rings;
  (c) cones

ACTUATORS, hydraulic, linear, self-contained, having ALL of the
 following:
   (a) minimum stroke length 140 mm;
   (b) push force of 10 kN;
   (c) minimum static load 12.5 kN;
   (d) pump plunger diameter NOT exceeding 16 mm;
   (e) main plunger diameter NOT exceeding 22 mm;
   (f) integral safety valve

HYDRAULIC STEERING CYLINDERS, EARTHMOVERS, including ANY of the 
following:  
  (a) piston seal assembly;  
  (b) rod;  
  (c) bearings;  
  (d) housing;  
  (e) seals;  
  (f) ring;  
  (g) gland;  
  (h) wiper;
  (i) plug;
  (j) capscrews;
  (k) lockwashers;
  (l) retainers;
  (m) locknut

RESTRAINT LOCKING UNITS, hydraulic

SERVOMOTORS, HYDRO-ELECTRIC TURBINE, hydraulic linear actuation

ACTUATORS, linear, having ALL of the following:
  (a) position feedback sensor;
  (b) sealed hydraulic pumping system;
  (c) double rod cylinder;
  (d) thrusts force NOT less than 2 000 Nm and NOT greater than 
      275 000 Nm; 
  (e) stroke ranges NOT less than 19 mm and NOT greater than 
      3 050 mm

HYDRAULIC ACTUATORS, OIL AND/OR GAS, with OR without ANY of the 
following:
  (a) exhaust valve assembly including O-ring;
  (b) handles;
  (c) switches;
  (d) plugs;
  (e) protectors; 
  (f) hydraulic OR mechanical openers; 
  (g) seals; 
  (h) bonnets

POWER ENGINES, linear, telescopic, hydraulic, having BOTH of the 
following:
  (a) working pressure NOT less than 130 bar; 
  (b) length NOT less than 1 000 mm
with OR without mounting bracket

HYDRAULIC CYLINDERS, HYDRO POWER STATION PLANT, linear 
actuation, having ALL of the following:
  (a) cylinder length NOT less than 1 m;
  (b) stroke length NOT less than 900 mm and NOT greater than 
      8 m;
  (c) outside diameter NOT less than 300 mm and NOT greater
      than 1 400 mm;
  (d) operating pressure NOT less than 2 bar and NOT greater than
      300 bar

POWER ENGINES, hydraulic, linear, single OR double acting 
telescopic, having BOTH of the following:
  (a) working pressure NOT less than 150 bar; 
  (b) length NOT less than 1 220 mm,
with OR without mounting bracket

DRIVES AND/OR ACTUATORS, BLAST FURNACE VALVE, hydraulic

CYLINDERS, KNUCKLE BOOM CRANE, being ANY of the following:
  (a) hydraulic telescoping boom cylinders;
  (b) hydraulic knuckle boom cylinders;
  (c) hydraulic main boom cylinders

PARTS, TUNNEL BORING MACHINE, being hydraulic cylinders

PARTS, TRACKED CRAWLER MACHINES, being track adjuster linear 
acting cylinders

MOTORS, LINEAR ACTING CYLINDER, electro-hydraulic, having ALL of 
the following:
  (a) absorbed power NOT greater than 300 W;
  (b) length NOT greater than 1 350 mm;
  (c) weight NOT greater than 12 kg

PARTS, STACKER AND/OR RECLAIMER, being hydraulic linear acting 
cylinders

PARTS, BUCKET LOADERS AND/OR REAR SCRAPERS AND/OR AGRICULTURAL 
TRACTORS, being linear acting hydraulically operated cylinders

MOTORS, hydraulic, variable volume, having a full displacement
 exceeding 54 cu cm/r

ACTUATORS, valve, hydraulically operated, sealed scotch yoke,
 double acting type for 1/4 turn operation of pipeline
 valves, having a torque output (break) greater than 2 700 N.m
 at a supply pressure of 3 445 kPa or greater, but not including
 actuators fitted with or to ANY of the following:
   (a) gas or hydraulic accumulators;
   (b) control cubicles/ systems;
   (c) pipeline valves

MOTORS, hydraulic, gear type having BOTH of the following:
   (a) maximum continuous pressure rating of 13 MPa or greater;
   (b) torque output of 3 N.m or greater/MPa at a maximum
       continuous speed of 2 000 r/min or greater

MOTORS, axial piston, fixed displacement, having BOTH of the
 following:
   (a) displacement exceeding 175 cu cm/r;
   (b) operating pressure exceeding 20 MPa

MOTORS, orbital, hydraulic, incorporating a displacement element
 to convert fluid energy to rotary power

MOTORS, hydraulic, having ANY of the following:
   (a) a torque output of 520 N.m or less/MPa and a maximum
       continuous speed of 1 600 r/min or less;
   (b) a torque output of 7 500 N.m or greater/MPa and a maximum
       continuous speed of 800 r/min or less;
   (c) a two speed operation capability with a torque output of
       520 N.m or greater/MPa but NOT exceeding 7 500 N.m/MPa and a
       maximum continuous speed of 800 r/min or less

ACTUATORS, valve, rotary vane, hydraulic, but NOT including
 actuators having a torque of 34 N.m or greater at 550 kPa but NOT
 exceeding 8 500 N.m at 550 kPa
   For the purposes of TC 8534424 actuators imported with ANY of
   the goods set out in THE TABLE are NOT admissible under this
   Order
                           THE TABLE
     (a) gas or hydraulic reservoirs;
     (b) control cubicles;
     (c) valves;
     (d) filters

MOTORS, piston, hydraulic, having ALL the following:
   (a) torque output of 29 N.m or greater/MPa;
   (b) maximum continuous pressure rating of 18 MPa or greater at a
       maximum continuous speed of 2 000 r/min or greater

MOTORS, piston, hydraulic, having a torque output of 1 N.m or
 less/MPa at a maximum continuous speed of 2 000 r/min or greater

MOTORS, hydraulic, gear or vane, having ALL of the following:
   (a) maximum continuous pressure rating of 13 MPa or greater;
   (b) torque output of 30 N.m or greater/MPa of rating at a
       maximum continuous speed of 2 000 r/min or greater

MOTORS, hydraulic, radial piston (but NOT including motors
 imported with gearboxes), having BOTH of the following:
   (a) maximum continuous speed NOT exceeding 100 r/min;
   (b) torque output 20 000 N.m or greater, when operating at
       17.5 MPa or greater

ACTUATORS, rotary, solely hydraulic operation for 280 degrees
 rotation, rated torque 4 500 N.m at 7 MPa

CRADLE DRIVES, DRILLING RIG, hydraulic

MOTORS, HYDRAULIC, down hole, positive displacement, hydraulic
 power driven, having ALL of the following:
   (a) rotor;
   (b) stator;
   (c) bent housings for directional control

MOTORS, hydraulic, vane type, having BOTH of the following:
   (a) maximum continuous pressure rating of 13 MPa OR greater;
   (b) torque output of 1.3 N.m OR greater per MPa at a maximum
       continuous speed of 2 000 r/min OR greater

MOTORS, axial piston, having BOTH of the following:
   (a) displacement of up to and including 16 cu cm/r, OR 45 cu cm/r
       OR greater
   (b) operating pressure of 31 MPa OR greater

MOTORS, hydraulic, having BOTH of the following:
   (a) imported as a single motor;
   (b) displacement exceeding 45 cu cm/r but NOT exceeding
       130 cu cm/r

MOTORS, hydraulic, gear, having ALL of the following:
   (a) a maximum operating pressure of EITHER of the following:
         (i) 10 MPa (1 500 psi) at 3 000 r/min;
        (ii) 13 MPa (2 000 psi) at 3 600 r/min;
   (b) an integral mechanical face seal;
   (c) capability of 10 MPa OR greater back pressure without a case
       drain

MOTORS, hydraulic, radial piston, having BOTH of the following:
   (a) operating pressure greater than 28 000 kPa (300 Kgf/sq cm);
   (b) torque output greater than 19 500 N.m (2 000 kgfm)

ACTUATORS, rotary, helical gear design, capable of maximum angular
 backlash of 0.5 degrees or less

VALVE ACTUATORS, ELECTROHYDRAULIC, with OR without spring return 
function, including ALL of the following:
  (a) proportional OR 3-position control;
  (b) 20 mm OR 40 mm stroke;
  (c) positioning force NOT less than 1 000 N and NOT greater  
      than 2 800 N;
  (d) operating voltage NOT less than 24 V AC and NOT greater 
      than 240 V AC;
  (e) manual adjuster AND position indicator;
  (f) hydraulic pump;
  (g) solenoid valve OR bypass valve

POWER PACKS, HYDRAULIC AND PNEUMATIC AND ELECTRICAL, OFFSHORE 
OIL AND/OR GAS WELL LOGGING, diesel engine, skid mounted, 
enclosed, whether OR not assembled, including ALL of the 
following:
  (a) protective frame AND lifting points;
  (b) dual pump gearbox drive;
  (c) oil cooling pump

GEAR MOTORS, hydraulic, with OR without gear reducer OR gearbox

MOTORS, HYDRAULIC, DOWNHOLE, whether OR not assembled, including 
ALL of the following:
  (a) rotor;
  (b) stator;
  (c) flow range NOT less than 385 litres per minute and NOT 
      greater than 850 litres per minute;
  (d) torque NOT less than 950 Newton meters;
  (e) flex shaft;
  (f) drive shaft;
  (g) thrust bearing stack;
  (h) radial bearing;
  (i) housings

MOTOR AND GEARBOX ASSEMBLIES, consisting of BOTH of the 
following:
  (a) swash plate AND axial piston hydraulic motor;
  (b) reduction drive gearbox

HYDRAULIC POWER MODULES, DOWNHOLE MECHANICAL INTERVENTION TOOL, 
OIL AND/OR GAS WELL, whether OR not assembled, including ALL of 
the following:
  (a) hydraulic pump;
  (b) upper AND lower connectors;
  (c) induction electric motor;
  (d) valves;
  (e) filters

HYDRAULIC POWER MODULES, DOWNHOLE SETTING OR RETRIEVING TOOL, 
OIL AND/OR GAS WELL, whether OR not assembled, including ALL of 
the following:  
  (a) reciprocating positive displacement pump;
  (b) synchronous motor;
  (c) oil reservoir;
  (d) valves

MOTORS, hydraulic, being ANY of the following:
  (a) blast hole drill rotary head axial piston motors;
  (b) air conditioner compressor vane type motors;
  (c) rock drill vane type motors

MOTORS, hydraulic, piston, bi-directional, having BOTH of the 
following:
  (a) speed NOT greater than 11 000 rpm;
  (b) pressure NOT greater than 42 000 kPa

DRIVE UNITS, TOOL, having a power capacity NOT greater than 40 kW

HYDRAULIC OIL SYSTEM, HIGH PRESSURE, comprising ALL of the 
following:
  (a) fuel valves;
  (b) tanks;
  (c) pumps;
  (d) filters;
  (e) accumulators;
  (f) pipes

HYDRAULIC POWER SYSTEM, comprising ALL of the following:
  (a) hydraulic cylinders;
  (b) AC motors;
  (c) converters;
  (d) pumps;
  (e) directional valves;
  (f) reciprocating grates

ACTUATORS, VALVE, hydraulic, subsea

ROTARY HEADS, PILING DRILL

MOTORS, HYDRAULIC, incorporating a planetary gearbox, integrated
 within a common housing, having a drive to load mounting angle of
 12 to 15 degrees

INTENSIFIERS, being cylinders having ALL of the following:
   (a) pneumatic input;
   (b) pneumatic/hydraulic powerstroke;
   (c) pneumatic return

THROTTLE PEDAL CONTROL CYLINDERS, pneumatic, having BOTH of the
 following:
   (a) nominal supply pressure of 1 034 kPa (150 psi);
   (b) nominal operating temperature range of - 40 degrees C OR
       greater but NOT exceeding + 93 degrees C

ACTUATORS, AIR HYDRAULIC, including BOTH of the following:  
  (a) air inlet pressure NOT greater than 11 bar;
  (b) cylinders having a hydraulic pressure NOT greater than 
      150 bar

PNEUMATIC PISTON ACTUATORS, single OR double cylinder, with OR 
without compression springs, having ALL of the following: ?
  (a) oil base dampener;
  (b) speed control;
  (c) anti-rotating coupling; 
  (d) tie rods

ACTUATORS, CLUTCH, pneumatic

ACTUATORS, AIR HYDAULIC, including BOTH of the following:  
  (a) air inlet pressure NOT greater than 11 bar;
  (b) cylinders having a hydraulic pressure NOT greater than 
      150 bar

PNEUMATIC PISTON ACTUATORS, OIL AND/OR GAS WELL, having ALL of 
the following:
  (a) compression spring;
  (b) single OR multiple piece housing;
  (c) piston;
  (d) top cap;
  (e) safety valve;
  (f) air supply pressure NOT greater than 18 bar

ACTUATORS, valve, pneumatic, gas operated, spring return type,
 having a torque rating of 3 000 N.m or greater at a gas pressure
 of 550 kPa or greater, but NOT including valve actuators imported
 with ANY of the following:
   (a) gas or hydraulic reservoirs;
   (b) control cubicles;
   (c) valves;
   (d) filters

MOTORS, air, dental handpiece

ACTUATORS, VALVE PNEUMATIC, API specification 14D AND/OR 6A, having
 a working valve pressure NOT less than 20 000 kPa

ACTUATORS, rotary pneumatic, but NOT including ANY of the
 following:
   (a) actuators having a torque at 550 kPa of 34 N.m OR greater in a
       double acting design;
   (b) actuators having a torque at 550 kPa of 15 N.m OR greater in a
       spring return design;
   (c) torque exceeding 8 500 N.m at 550 kPa

VALVE ACTUATORS, pneumatic, with OR without positioners

ACTUATOR ASSEMBLIES, GAS WATER HEATER, having ALL of the 
following:
  (a) housing;
  (b) bush;
  (c) shaft;
  (d) coupling;
  (e) piston;
  (f) spring;
  (g) pin;
  (h) interlock arm AND/OR link;
  (i) piston cap;
  (j) damper indicator;
  (k) washer AND/OR seal;
  (l) housing liner;
  (m) bellows;
  (n) screw;
  (o) compression connector;
  (p) bracket

ACTUATORS, pneumatic, electric (24 V DC) solenoid operated, 
spring return type, including ALL of the following:
  (a) torque range rating 12 Nm to 732 Nm at an air pressure of
      5.5 bar or greater;
  (b) advanced communication and control system;
  (c) integrated automation package with limit switch

PARTS, HYDRAULIC MOTOR, being ANY of the following:
   (a) front housing cover;
   (b) rear housing cover;
   (c) rotor housing;
   (d) cam;
   (e) brake

PARTS, HYDRAULIC MOTOR, being ANY of the following:
   (a) wear rings;
   (b) shaft housings;
   (c) connection blocks;
   (d) cylinder blocks;
   (e) guide plates;
   (f) distributors;
   (g) side guides;
   (h) cam rings;
   (i) rear end covers;
   (j) front end covers;
   (k) brake cylinders;
   (l) mounting flanges;
   (m) valve housings;
   (n) torque arms;
   (o) piston rods;
   (p) piston rings;
   (q) reconditioning sets comprising ANY or ALL of the following:
          (i) safety couplings;
         (ii) cam rings;
        (iii) piston rods;
         (iv) piston rings;
          (v) guide plates;
   (r) brake assemblies comprising ANY or ALL of the following:
          (i) brake bands;
         (ii) front brake levers;
        (iii) rear brake levers;
         (iv) brake brackets;
          (v) brake cylinders;
         (vi) brake direction plates

CARTRIDGES, HYDRAULIC VANE MOTOR, having ALL of the following:
   (a) cam ring;
   (b) rotor;
   (c) vanes;
   (d) vane springs

PARTS, EXCAVATOR, BOOM OR HOIST CYLINDER, being ANY of the 
following:
  (a) liners OR housings;
  (b) piston rods; 
  (c) forks;
  (d) pistons with OR without guide rings

PARTS, PNEUMATIC VALVE ACTUATOR, being ANY of the following:
   (a) centerbars;
   (b) cover plate for spring cans;
   (c) cylinders;
   (d) cylinder adaptors;
   (e) extension rods;
   (f) guide bars;
   (g) guide blocks;
   (h) housings;
   (i) housing covers;
   (j) hydraulic override units;
   (k) inner end caps;
   (l) outer end caps;
   (m) pipe plugs;
   (n) pistons;
   (o) piston rods;
   (p) position indicator units;
   (q) rod bushings;
   (r) rod wipers;
   (s) split rings;
   (t) spring cartridges;
   (u) spring cartridge weldments;
   (v) spring guides;
   (w) tension loks;
   (x) tension rods;
   (y) tension rod bushings;
   (z) tiebars;
  (aa) torque shafts;
  (ab) yokes;
  (ac) yoke covers;
  (ad) yoke keys;
  (ae) yoke pins

PARTS, HYDRAULIC MOTOR, DOWNHOLE, being lower assemblies 
including ALL of the following:
  (a) transmission;
  (b) fixed bend housing AND/OR adjustable bend housing;
  (c) stator adaptor housing;
  (d) driveshaft sub-assembly including ALL of the following:
          (i) bearings;
         (ii) catch;
        (iii) spacers;
         (iv) bearing housing

PARTS, MUD MOTOR, hydraulic, being ANY of the following:
  (a) adjusting rings;
  (b) eccentric stabilisers;
  (c) insulating discs;
  (d) lower cross over subs;
  (e) lower pressure sleeves;
  (f) offset housings;
  (g) pickup subs;
  (h) ported end caps;
  (i) rotors;
  (j) rotor catchers;
  (k) stabiliser pads;
  (l) stabiliser shims;
  (m) stators;
  (n) stator housing adaptors;
  (o) upper pressure sleeves

PARTS, HYDRAULIC MOTOR, downhole, being lower assemblies 
including ALL of the following:
  (a) transmission;
  (b) fixed bend housing;
  (c) driveshaft sub-assembly including ALL of the following:
          (i) bearings;
         (ii) catch;
        (iii) spacers,
  (d) stator adaptor housing

PARTS, POSITIVE DISPLACEMENT MOTOR, OIL AND/OR GAS WELL, being 
ANY of the following:
  (a) stator;
  (b) rotor;
  (c) housing;
  (d) stabiliser

PARTS, EXCAVATOR STICK CYLINDER, being ANY of the following:
  (a) piston rods;
  (b) guide rings;
  (c) liners;
  (d) forks

PARTS, MARINE THRUSTER, comprising of ANY of the following:
  (a) fuseholders;
  (b) fusers;
  (c) tunnels;
  (d) switches;
  (e) serial-parallel switch box;
  (f) control cables;
  (g) solenoids;
  (h) control panel joystick;
  (i) anodes;
  (j) gear house;
  (k) propellers

CAM ROLLER ASSEMBLY, HYDRAULIC MOTOR, comprising ALL of the 
following:
  (a) cam roller;
  (b) roller bearings;
  (c) guide rings;
  (d) lock rings

PUMPS, FUEL, with OR without hoses

PUMPS, peristaltic, roller endoscopic irrigation

PUMPS, being components of pressure gauge testing equipment

PUMPS, blood, roller, perfusion control

INJECTORS, fertiliser, water or air powered, having a maximum
 injection rate of NOT less than 250 L/h

PUMPS, TRAILER OR SKID MOUNTED FRACTURING SERVICE, PROPPANT AND
 CHEMICAL PROCESSING, OIL OR GAS WELL, having ALL of the following:
   (a) one OR more reciprocating triplex pumps;
   (b) remote control;
   (c) turbo charged pump engine

PUMPS, VOLUMETRIC, parenteral or enteral fluid delivery

PUMPS, FUEL TRANSFER, 12 V DC OR 24 V DC

CHEMICAL DOSING AND PUMPING SYSTEM, PARTICLE BOARD, programmable 
logic controlled, including ALL of the following:
  (a) two dosing boxes NOT greater than 760 L;
  (b) five dosing boxes NOT greater than 500 L;
  (c) flow meters;
  (d) pumps

SOLENOID MEMBRANE PUMPS, DIESEL EXHAUST FLUID, metering

PUMPS, BINARY RAPID SEPARATION, nano AND/OR capillary, having 
one OR more of the following:
  (a) flow meter;
  (b) ternary loading pump;
  (c) column compartment

RECYCLING AND/OR PUMPING MACHINES, GLASSHOUSE WASTE WATER, 
including ALL of the following:
  (a) pressures sensors;
  (b) flow transmitters;
  (c) temperature AND/OR electrical conductivity sensors;
  (d) motorised valves

HYDRAULIC PUMPING UNIT, AIRCRAFT, dual system, 4 wheel towable

PUMP LOADING AND UNLOADING SKIDS, LIQUID, metering, with OR 
without flame arrestors, having ALL of the following:
  (a) meters;
  (b) junction box;
  (c) check valves;
  (d) pressure gauges

WATER PUMPING PLANT, comprising ALL of the following:
  (a) piping;
  (b) pumps;
  (c) valves;
  (d) manifolds;
  (e) cabling;
  (f) electrical instrumentation modules and/or controllers

PUMPS, bilge, hand operated

PUMPS, hydraulic oil, hand lever operated, non-motorised, two
 speed, displacement in first stage exceeding 130 cc/stroke at
 1 300 kPa, maximum operating pressure exceeding 65 000 kPa but NOT
 exceeding 70 000 kPa

PUMPS, DRUM TRANSFER, hand operated, positive displacement, rotary
 vane OR centrifugal, incorporating an inlet tube

PUMPS, DRUM TRANSFER, rotary vane OR reciprocating, corrosive
 resistant, having BOTH of the following:
   (a) inlet tube;
   (b) all wetted parts of plastic OR stainless steel, other than
       seals OR bearings

PUMPS, syphon, flow rate up to 25 L/min

DRUM PUMPS, hand operated, capacity NOT greater than 20 litres

OIL PUMPS, manually operated, with 1 litre reservoir

PUMPS, fuel, electronic, motor vehicle

PUMPS, automotive petrol fuel injection, electrically operated,
 operating pressure 85 kPa or greater

PUMPS, fuel, electric, motorcycle

PUMPS, water cooling, marine outboard engine

PUMPS, fuel, diaphragm, being pumps which operate off two-stroke
 petrol engine crankcase pressure (ie induction and compression
 pulse)

PUMPS, FUEL, MOTOR VEHICLE, electric

PUMPS, DIESEL ENGINE, being EITHER of the following:
   (a) lubricating oil pumps;
   (b) water pumps

PARTS, PASSENGER MOTOR VEHICLE, manufactured at least 30 years
 before the goods are entered for home consumption, or reproductions
 of these parts, being ANY of the following:
  (a) water pumps;
  (b) oil pumps

PUMPS, diesel engine, being either of the following:
   (a) oil pumps;
   (b) water pumps,
 but NOT including pumps which perform both functions

OIL LUBRICATION UNIT, including of ALL of the following:
  (a) oil tank;
  (b) pumps;
  (c) filtration unit;
  (d) pressure control unit;
  (e) flow control unit;
  (f) pipe AND fittings;
  (g) oil supply temperature to process NOT less than 40 
      degrees C;
  (h) minimum start up oil supply temperature NOT less than
      10 degrees C

AUXILIARY MODULES, DUAL FUEL ENGINE, unassembled, having ALL of 
the following:
  (a) control panel supports;
  (b) electric motors;
  (c) filters;
  (d) flowmeters;
  (e) frame;
  (f) frame foot;
  (g) grating;
  (h) level switches;
  (i) lube oil cooler frame;
  (j) manometers;
  (k) pipes AND spools;
  (l) plate heat exchangers;
  (m) pressure difference indicators;
  (n) pumps;
  (o) supports;
  (p) switch panel frame;
  (q) tanks;
  (r) temperature sensors;
  (s) valves

OIL LUBRICATION PUMPS, GAS FUELLED POWER PLANT ENGINE

COOLING PUMPS, PASSENGER AND/OR LIGHT COMMERCIAL VEHICLE, 
mechanical, belt driven

PUMPS, FUEL, mechanical, motor vehicle

PUMPS, CONCRETE, remote controlled, including a greasing system 
incorporating ALL of the following:
  (a) tank;
  (b) plunger;
  (c) tubes;
  (d) grease level switch

CONCRETE PUMPS, articulated boom, truck mounted, having BOTH of 
the following:
  (a) double walled delivery pipe with chrome carbide collars;
  (b) hydraulic outriggers

PUMPS, agricultural spray, P.T.O. driven type, having ALL of the
 following:
   (a) 1 000 r/min maximum;
   (b) maximum working pressure of 15 bar or greater;
   (c) output of 22.8 L/min or greater at open flow

PUMPS, 12 V or 24 V DC, positive displacement, diaphragm, having
 ALL of the following:
   (a) pressure demand switch;
   (b) self priming;
   (c) run dry indefinitely without damage;
   (d) in line inlet and outlet ports

PUMPS, air operated, reciprocating, complying with BOTH of the
 following:
   (a) pressure ratio of 2.5:1 or greater but NOT exceeding 300:1;
   (b) ALL of the wettable parts are of stainless steel

PUMPS, diaphragm, agricultural spray, tractor PTO driven,
 output NOT less than 101 L/m at 2 000 kPa

PUMPS, diaphragm, 12 V, capable of delivering maximum flow of
 6 L/min at maximum discharge pressure of 420 kPa

PUMPS, liquid, air driven, having ALL of the following:
   (a) an air driven reciprocating piston motor integrally driving a
       reciprocating piston or plunger pump;
   (b) a nominal kW rating exceeding 0.2 kW but NOT exceeding 10 kW;
   (c) a nominal continuous liquid output pressure rated at 2 000 kPa
       or greater;
   (d) an air cycling valve axis 90 degrees to pump drive axis,
 NOT being:
   (a) drum transfer pumps;
   (b) pumps capable of pumping grease; or
   (c) foot operated pumps

PUMPS, desalination, reverse osmosis

PUMPS, soft drink syrup dispensing, carbon dioxide or air
 operated, self priming, having a delivery rating NOT exceeding
 210 mL/s

PUMPS, rated at a continuous working pressure of 140 MPa or
 greater

PUMPS, triplex or duplex, piston diaphragm, with multiple
 diaphragms actuated by hydraulic pressure, complying with ALL of
 the following:
   (a) piston dia of 100 mm or greater;
   (b) stroke of 150 mm or greater;
   (c) maximum working pressure of 5 000 kPa or greater

PUMPS, triplex, plunger, complying with BOTH of the following:
   (a) plunger dia of 80 mm or greater;
   (b) stroke of 150 mm or greater

PUMPS, hydraulic oil, radial or axial piston type, with
 displacement exceeding:
   (a) 220 cu cm/r as single pumps (NOT grouped with other pumps to
       form multi-pumps); or
   (b) 440 cu cm/r as double pumps (two pumps close coupled together)

DEWATERING PUMP ASSEMBLIES, two cylinders double acting, piston 
diaphragm, having ALL of the following:
  (a) piston diameter NOT less than 150 mm;
  (b) pump stroke length NOT less than 300 mm;
  (c) slurry flow NOT greater than 80 m?/h;
  (d) suction pressure NOT greater than 1 000 kPa,
with OR without ANY of the following:
          (i) pulsation dampener;
         (ii) suction air vessel AND connection line;
        (iii) control cabinet

PUMP HOUSE, trailer OR skid mounted, including ALL of the 
following:
  (a) triplex reciprocating positive displacement pumps; 
  (b) AC motor;
  (c) motor control centre panel AND cabinet; 
  (d) four axle trailer;
  (e) air compressor

HYDRAULIC MEMBRANE PUMPS, TAILINGS TRANSFER, having BOTH of the 
following:
  (a) piston diameter NOT less than 180 mm; 
  (b) stroke NOT less than 320 mm

PUMPS, SLURRY, two cylinder double acting, reciprocating 
positive displacement, having ALL of the following:
  (a) piston diameter NOT less than 150 mm;
  (b) pump stroke length NOT less than 300 mm; 
  (c) dewatering pump motor;
  (d) air compressor;
  (e) suction air vessel

PLUNGER PUMPS, RECIPROCATING HORIZONTAL QUINTUPLEX, positive 
displacement, hydraulic

PUMPS, OIL AND GAS EXPLORATION OR PRODUCTION, fracturing, 
trailer OR skid mounted

PUMPS, TRIPLE PLUNGER, (TRIPLEX)

PUMPS, HYDRAULIC, having ALL of the following:
   (a) hydraulic oil pump;
   (b) AC OR DC motor;
   (c) operating pressure of 70 MPa OR greater;
   (d) with OR without reservoirs

PUMPS, OPEN CIRCUIT HYDRAULIC RADIAL OR AXIAL PISTON, having
 ALL of the following:
   (a) single pumps;
   (b) one-way flow;
   (c) self priming;
   (d) variable displacement capacity less than 17 cu cm/rev and
       greater than 45 cu cm/rev

PUMPS, CLOSED CIRCUIT HYDRAULIC AXIAL PISTON, having BOTH of the
 following:
   (a) output pressure greater than 30 MPa;
   (b) variable displacement capacity less than 17 cu cms/rev and
       greater than 45 cu cms/rev

PUMPS, RECIPROCATING PISTON, air powered, having a maximum output
 pressure exceeding 62 bar (900 psi)

PUMPS, RECIPROCATING PISTON, but NOT including EITHER of the
 following:
   (a) piston operated diaphram pumps;
   (b) metering pumps

PUMP, GREASE, pnuematically OR electrically (12 V or 24 V) operated,
 incorporating a plastic grease reservoir, having ALL of the
 following:
   (a) reservoir capacity of 4 L;
   (b) grease delivery per stroke of 42 cc;
   (c) pump ratio 9 : 1;
   (d) grease pressure of 72 bar at air pressure of 8 bar;
   (e) maximum grease pressure 100 bar;
   (f) temperature range between - 25 degrees C to + 80 degrees C;
   (g) total weight 5.2 kg

PUMPS, HYDRAULIC, piston, fixed displacement, bent axis, having
 ALL of the following:
   (a) functional as a motor or pump;
   (b) open or closed circuit applications;
   (c) maximum continuous operating pressure of 35 MPa OR greater;
   (d) displacement exceeding 4.8 cu cm/r but NOT exceeding
       250 cu cm/r

PUMPS, triplex, piston or plunger, having BOTH of the following:
   (a) nominal flow of 12 cu m/h OR greater at 1 800 r/min;
   (b) maximum design pressure up to 180 bar

PUMPS, hydraulic oil, axial piston type, variable displacement,
 having BOTH of the following:
   (a) imported as a single pump;
   (b) displacement exceeding 60 cu cm/r but NOT exceeding
       130 cu cm/r

PUMPS, positive displacement reciprocating plunger type, with
 plungers of polished ceramics, having ALL of the following:
   (a) maximum RPM NOT exceeding 3800;
   (b) maximum working pressure 7 bar or greater, but NOT exceeding
       248 bar;
   (c) output of 4.8 L/min or greater but NOT exceeding 30.7 L/min

PUMPS, positive displacement, reciprocating plunger type,
 with plungers of polished ceramics, having ALL of the
 following:
   (a) maximum r/min not exceeding 3 800;
   (b) maximum working pressure 7 bar OR greater, but NOT
       exceeding 248 bar;
   (c) output of 4.8 L/min OR greater but NOT exceeding 136 L/min

PUMPS, positive displacement, reciprocating twin piston type with
 piston cups of either rubber or leather, having ALL of the
 following:
   (a) maximum r/min NOT exceeding 1800;
   (b) maximum working pressure 3.5 bar OR greater but NOT exceeding
       35 bar;
   (c) output of 1.9 L/min OR greater but NOT exceeding 13.5 L/min

PUMPS, positive displacement, reciprocating twin piston type, with
 piston cups of either rubber, leather or fabric material,
 having ALL of the following:
   (a) maximum r/min NOT exceeding 800;
   (b) maximum working pressure of 1.7 bar OR greater but NOT
       exceeding 28 bar;
   (c) output of 14L/min OR greater but NOT exceeidng 38L/min

PUMPS, HYDRAULIC EXCAVATOR, DUAL UNIT, including ANY of the 
following:
  (a) brackets;
  (b) fasteners, with screws AND nuts;
  (c) cables;
  (d) washers, with lock washers;
  (e) sleeves;
  (f) clamps;
  (g) screw extension tubes;
  (h) hoses;
  (i) rings, with O-rings;
  (j) flanges;
  (k) gauge connectors;
  (l) intake stacks

PUMPS, HYDRAULIC EXCAVATOR, DUAL UNIT

PUMPS, RECIPROCATING POSITIVE DISPLACEMENT, hydraulic steering

HYDRAULIC POWER PACKS, DRILLING RIG, diesel, including ALL of 
the following:
  (a) drive AND rotary drive hydraulic pumps;
  (b) oil, OR water, OR diesel, absorption tray;
  (c) oil filtration AND cooling pump;
  (d) hydraulic oil tank NOT less than 185 gal;
  (e) power connection 480 V / 60 Hz

MUD PUMPS, trailer mounted, programmable logic controlled, 
including ALL of the following:
  (a) triplex pump;
  (b) diesel engine;
  (c) choke manifold;
  (d) bi-axle air ride chassis

PUMPS, CENTRAL LUBRICATION, electric, with OR without integrated 
controller, having ALL of the following:
  (a) lubricant reservoir with OR without lubricant level
      switch AND/OR connection cable;
  (b) DC OR AC motor;
  (c) pump housing having inlet AND/OR outlet ports;
  (d) pump element with OR without micro switch AND/OR 
      malfunction indicator

PUMPING SYSTEM, OIL AND/OR GAS, EXPLORATION AND/OR PRODUCTION, 
skid mounted, with OR without fuel tanks, including ALL of the 
following: 
  (a) engine;
  (b) transmission;
  (c) reciprocating pump;
  (d) remote control panel;
  (e) radiator

PUMPING SYSTEM, OIL AND/OR GAS EXPLORATION AND/OR PRODUCTION, 
trailer mounted, whether OR not assembled, including ALL of the 
following:
  (a) NOT less than two fuel tanks;
  (b) reciprocating pump;
  (c) engine;
  (d) transmission;
  (e) radiator;
  (f) control panel

PUMPS, METERING, diaphragm OR plunger, including ALL of the 
following:
  (a) stainless steel liquid end;
  (b) rated capacity NOT less than 450 litre per hour;
  (c) maximum pressure exceeding 150 bar

PUMPS, DIAPHRAGM, air operated, having ALL of the following:
  (a) flow rate NOT greater than 820 litres per min;
  (b) operating output pressure NOT greater than 16 bar;
  (c) temperature range NOT less than -20 degrees Celsius AND 
NOT greater than 110 degrees Celsius;
  (d) connection sizes NOT less than DN8 AND NOT greater than 
DN80;
  (e) monobloc construction

HYDRAULIC PUMP SYSTEM, with OR without remote control panel, 
including ALL of the following:
  (a) control console;
  (b) pressure gauges;
  (c) switches;
  (d) valves;
  (e) regulators;
  (f) tanks;
  (g) accumulators;
  (h) air operated hydraulic pumps;
  (i) uninterruptible power supply;
  (j) cables

PUMPS, reciprocating piston, pressure NOT greater than 36 bar, 
with OR without EITHER of the following:
  (a) internal combustion engine;
  (b) electric motor

HYDRAULIC POWER MODULES, OIL AND/OR GAS WELL RESERVOIR, whether 
OR not assembled, including ALL of the following:
  (a) hydraulic pumps;
  (b) DC motor;
  (c) electronic control module;
  (d) sensors;
  (e) accumulator;
  (f) compensator

PUMPING SYSTEM, skid mounted, including ALL of the following:
  (a) three plunger positive displacement pumps;
  (b) centrifugal pump;
  (c) diesel engine;
  (d) manual transmission;
  (e) maximum output pressure rating NOT less than 650 bar

RESERVOIR PUMP MODULE, OIL AND/OR GAS WELL, downhole, whether OR 
not assembled, including ALL of the following:
  (a) pressure rating NOT less than 1 300 bar; 
  (b) valves;
  (c) pumps; 
  (d) motor; 
  (e) hydraulic controls;
  (f) pressure compensator;
  (g) electronic control AND sensors

NITROGEN PUMPING SYSTEM, HEAT RECOVERY, skid mounted, including 
ALL of the following:
  (a) engine;
  (b) transmission;
  (c) cryogenic triplex pump;
  (d) control panel

PUMPS, SLURRY, positive displacement, including BOTH of the 
following:
  (a) hydraulic cylinders;
  (b) hydraulic changeover valves

HYDRAULIC POWER MODULES, having ALL of the following:
  (a) main pump;
  (b) auxiliary pump;
  (c) cooling AND/OR filtering pump

PUMPING SYSTEM SKIDS, having ALL of the following:
  (a) reciprocating positive displacement pump;
  (b) hydraulic hoses;
  (c) valves;
  (d) control panel;
  (e) diesel engine;
  (f) transmission

HYDRAULIC FLUSHING UNITS, SUBSEA OIL AND/OR GAS WELL EQUIPMENT, 
skid mounted, having ALL of the following:
  (a) pumps;
  (b) filters;
  (c) controls;
  (d) steel frame;
  (e) pressure gauges

PUMPS, GREASE, rotary hydraulic drive, positive displacement, 
double acting

PUMPS, POSITIVE DISPLACEMENT, reciprocating triplex plunger, 
including ALL of the following:
  (a) safety relief valve;
  (b) mechanical AND/OR electro hydraulic unloading valve;
  (c) operating output pressure rating NOT less than 
      5 000 kPa (50 bar) and NOT greater than  
      80 000 kPa (800 bar);
  (d) flow rate NOT less than 100 L/min and NOT greater than
      800 L/min

PUMPS, CONDENSATE, AIR CONDITIONING, with OR without float 
switch

POWER PACKS, hydraulic, comprising ALL of the following:
  (a) electric motors;
  (b) hydraulic pumps;
  (c) oil reservoir tanks

PUMPS, RECIPROCATING, axial piston, variable displacement

PUMPS, MARINE HELM, hydraulic axial piston, having BOTH of the 
following:
  (a) roller OR ball bearing race;
  (b) lock valve

PUMPS, HYDRAULIC FLUID, axial piston variable, swash plate, 
having a maximum flow rate NOT less than 450 cubic cm per 
revolution

CHEMICAL DOSING SYSTEM, WATER TREATMENT PLANT, comprising ALL of 
the following:
  (a) pumps;
  (b) chemical dosers;
  (c) valves;
  (d) pipes and fittings;
  (e) control modules

PUMPS, PISTON DIAPHRAGM, SLURRY, having ALL of the following:
  (a) flow rate NOT greater than 273 m3/h;
  (b) pressure NOT exceeding 4 500 kPa;
  (c) solids concentration exceeding 65%

PISTON PUMPS, SLUDGE, with or without hydraulic power packs

PUMPS, TRANSFER, NON PULSATING DISCHARGE, having BOTH of the 
following:
  (a) eccentric motion elliptical cams;
  (b) NOT less than 2 opposing independent flow diaphragms

PUMPS, triplex, positive displacement reciprocating plunger type,
 having BOTH of the following:
   (a) rating of NOT less than 600 bar;
   (b) displacement NOT less than 9 litres per minute

PUMPS, hydraulic oil, axial piston type, variable displacement,
 having ALL of the following:
   (a) imported as double pumps (two pumps close coupled together);
   (b) through drive capability to 100% of front pump
       specifications;
   (c) displacement in each pump making up the double pump,
       exceeding 60 cu cm/r but NOT exceeding 130 cu cm/r

POWER UNITS, hydraulic, operated solely by DC power supply,
 comprising BOTH of the following:
   (a) hydraulic oil pump;
   (b) DC motor,
 with or without reservoirs

PUMPS, cavity, progressing, capable of continuous operation at a
 flow rate of 150 cu m/h or greater

PUMPS, hydraulic, internal gear, having a maximum operating
 pressure of 21 MPa or greater but NOT exceeding 33 MPa

PUMPS, hot melt plastic

PUMPS, vane type, having BOTH of the following:
   (a) maximum continuous working pressure 3.5 MPa or greater;
   (b) automatically variable output volume by pressure
       compensation

PUMPS, multilobe, self priming, complying with BOTH of the
 following:
   (a) capacity exceeding 1 100 L/min;
   (b) the wettable pump parts (that is, those pump parts coming
       into contact with the liquid being pumped) are of stainless
       steel hygienic construction to 3A Approval

PUMPS, twin-screw, horizontal external bearing, having external
 timing gears in separate oil bath, capable of pumping residual
 fuel oil with a viscosity of 350 cSt at 354 cu m/h pulse free at
 880 kPa

PROGRESSING CAVITY PUMPS, being a rotary positive displacement 
pump having BOTH of the following:
  (a) rotor;
  (b) stator

PUMPS, GEAR LUBRICATION, ROLL GRINDER, rotary positive 
displacement

OIL PUMPS, screw spindle

PUMPS, DRUM TRANSFER, rotary positive displacement, having ALL of
 the following:
   (a) pump inlet tube;
   (b) 12 V OR 24 DC electric OR air motor driven

PUMPS, ENTERAL OR PARENTAL FLUID

PUMPS, rolling vane type, petrol engine or electric motor driven,
 having ALL of the following:
   (a) maximum working pressure NOT exceeding 10.35 bar;
   (b) maximum r/min NOT exceeding 2600;
   (c) output of 12.5L/min OR greater at open flow, but NOT
       exceeding 34.4L/min

MORTAR MIXING PUMPS, including ALL of the following:
  (a) output NOT less than 2 L/min and NOT greater than 35 L/min
  (b) hopper; 
  (c) spray gun

POWER PACKS, hydraulic, including ALL of the following:
  (a) engine output NOT greater than 207 Kw;
  (b) axial piston variable pump;
  (c) oil reservoir tank

GEAR PUMPS, POSITIVE DISPLACEMENT, including ALL of the 
following:
  (a) stainless steel housing;
  (b) brushless motor;
  (c) voltage NOT less than 23 V DC;
  (d) self-priming

INJECTION PUMP SYSTEM, PRODUCED WATER, GAS INJECTION PLANT, 
including ALL of the following:
  (a) positive displacement pumps;
  (b) control panel;
  (c) lube oil skid;
  (d) seal oil skid;
  (e) job sensors; 
  (f) piping skid

PUMPS, rotary lobe, positive displacement, self-priming, with OR 
without valves

PUMPS, CENTRAL LUBRICATION, electric, with OR without control 
unit, pressure gauge, pressure switch OR fill level switch, 
having ALL of the following:
  (a) lubricant reservoir;
  (b) DC motor;
  (c) filler socket with OR without strainer;
  (d) electric motor cover cap;
  (e) gear pump unit;
  (f) supply voltage plug

ROTARY LOBE PUMPS, having ALL of the following:
  (a) metallic tri-lobe rotors;  
  (b) duplex stainless steel rotor casing;
  (c) front cover mounted integral pressure relief valve;
  (d) flow capacity NOT greater than 36 cubic m³/hr

GEAR PUMPS, whether OR not assembled, including ALL of the 
following:
  (a) stainless steel housing;
  (b) brushed motor having a rated voltage NOT less than 
      23 V DC;
  (c) wire connections;
  (d) seals, 
with OR without valve

HYDRAULIC PUMP SYSTEM, containerised, with OR without motors, 
including ALL of the following:
  (a) pumps;
  (b) reservoirs;
  (c) accumulators;
  (d) flame arrestors;
  (e) valves;
  (f) level gauges;
  (g) pressure gauges;
  (h) control panel;
  (i) flowmeters;
  (j) filters

PUMPS, POSITIVE DISPLACEMENT, vane, reverse osmosis, with OR 
without ANY of the following:
  (a) isobaric pressure exchanger;
  (b) electric motor

PUMPS, vane, having BOTH of the following:
  (a) working pressure NOT less than 1.0 MPa;
  (b) variable flow rate

PUMPS, jacketed, rotary positive displacement, having flexible 
impellers

PUMPS, ROTARY POSITIVE DISPLACEMENT, having ALL of the 
following:
  (a) pump capacity exceeding 5 m3/h and NOT exceeding 270 m3/h;
  (b) displacement exceeding 10 L/rev and NOT exceeding 75L /rev;
  (c) NOT less than two impellers

PUMPS, PROGRESSIVE CAVITY, having BOTH of the following:
  (a) flow capacity NOT greater than 450 m3/h;
  (b) differential pressure NOT greater than 24 bar

PUMPS, PROGRESSIVE CAVITY, single AND/OR multilobe, having a 
flow pressure rate NOT less than 0.04 m3/hr and NOT greater than 
200 m3/hr

WORM SCREW PUMPS, portable, having a removable motor

HYDRAULIC PUMP SYSTEM, including ALL of the following:
  (a) accumulators;
  (b) multiphase AC motors;
  (c) pumps

PUMPS, EXTERNAL GEAR, hydraulic

PUMPS, EXTERNAL GEAR, HYDRAULIC EXCAVATOR

ELECTRO-HYDRAULIC POWER UNITS, comprising ALL of the following:
  (a) hydraulic oil pumps;
  (b) electric motors;
  (c) reservoirs

PUMPS, ROTARY POSITIVE DISPLACEMENT, having a rotary vane air 
motor

PUMPS, HYGIENIC, positive displacement, rotary lobe, having BOTH
of the following:
  (a) stainless steel construction of wettable parts;
  (b) bi-wing OR multi-lobe rotor operation

PUMPS, LUBRICATION, double helical gear, having ALL of the 
following:
  (a) discharge capacity NOT less than 450 L/min;
  (b) distance from shaft end to centre line of port position 
      NOT greater than 450 mm

PUMPS, ROTARY LOBE, positive displacement, self-priming, 
valveless, having elastomer coated rotors

PUMPS, peristaltic

PUMPS, rotary, 3 screw, positive displacement

PUMPS, CAVITY PROGRESSIVE, comprising BOTH of the following:
   (a) outside diameter NOT less than 70 mm and NOT greater than
       135 mm;
   (b) single or multi lobe

PUMPS, GRINDER, SEWAGE

PUMPS, HYDRAULIC, internal gear, having an operating pressure
 greater than six thousand (6,000) kPa

PUMPS, SLURRY, seal-less, reversible, dry running, having parallel
 inlet and outlet ports

CIRCULATOR PUMPS AC, canned rotor type, being pump and motor forming
  an integral unit without mechanical shaft seal and with only two
  gaskets and liquid lubricated bearings, 1x240 volts or 3x415 volts,
  pipe mounted without external support, having all of the following:
   (a) cast iron, stainless steel or bronze pump housing;
   (b) liquid temperature ranges -25 degrees C to +35 degrees C or
       +2 degrees C to 110 degrees C;
   (c) maximum hydrostatic pressure - 10 bars;
   (d) port sizes - 18mm - 50mm (3/4in to 2in) inclusive;
   (e) head range: 0-6 metres head;
   (f) flow range - 0-2.8 litres/sec;
   (g) power range - 0-250 watts;
   (h) dimensions - port to port not exceeding 180mm;
   (i) height < 180mm.

PUMPS, centrifugal, magnetic drive, seal-less, having ALL of the
 following:
   (a) ceramic shaft and ceramic/carbon impeller bearings;
   (b) no metal contact with pump medium;
   (c) ability to handle products with temperatures NOT exceeding
       100 degrees C;
   (d) capability of pumping highly corrosive liquids;
   (e) able to pump liquids with specific gravities NOT exceeding
       1.8

PUMPS, centrifugal, magnetic drive, seal-less, having ALL of the
 following:
   (a) ceramic shaft and ceramic/carbon impeller bearings;
   (b) head NOT exceeding 4 m;
   (c) flow rate NOT exceeding 40 L/min;
   (d) no metal contact with pump medium

PUMPS, dewatering, portable, submersible, 12 V or 24 V,
 DC operated

REPAIRED, PUMPS, SUBSEA, multiphase, with OR without steel 
frame  
For the purposes of this Order, these goods had been sent out of 
Australia for repair prior to importation

PUMP SYSTEM, SUBSEA, multiphase, whether OR not assembled, 
consisting of ALL of the following:
  (a) piping;
  (b) impact dampers;
  (c) flowline connectors;
  (d) valves;
  (e) hydraulic connectors;
  (f) electrical connectors;
  (g) venturi tube, having BOTH of the following:
        (i) flow mixer;
       (ii) splitter,
  (h) dummy pump modules;
  (i) mud mat;
  (j) pressure AND/OR temperature transducers;
  (k) NOT less than one multistage rotodynamic pump

PUMP SYSTEM, SUBSEA, multiphase, whether OR not assembled, 
consisting of ALL of the following:
  (a) multistage rotodynamic pumps;
  (b) piping;
  (c) impact dampers;
  (d) flowline connectors;
  (e) valves;
  (f) hydraulic connectors;
  (g) electrical connectors;
  (h) venturi tube, having BOTH of the following:
        (i) flow mixer AND splitter;
       (ii) pressure AND/OR temperature transducers,
  (i) mud mat;
  (j) dummy pump modules, including BOTH of the 
      following:
        (i) frames;
       (ii) lifting points

PUMP SYSTEM, SUBMERSIBLE, DOWNHOLE, electric, whether OR not 
assembled, including ALL of the following:
  (a) connectors;
  (b) sensor;
  (c) motor;
  (d) motor base;
  (e) couplings;
  (f) intake pressure protectors;
  (g) pumps;
  (h) discharge head;
  (i) ported intake chamber

PUMPS, DOWNHOLE, electric, submersible, multistage centrifugal, 
with OR without motors, having BOTH of the following:
  (a) carbide bearings;
  (b) carbide downthrust modules OR carbide flanged sleeves AND 
      pedestals

PUMPS, SUBSEA, OIL AND GAS WELL, skid mounted, having BOTH 
following:
  (a) centrifugal pumps;
  (b) electrical power modules

PUMP SYSTEM, SUBMERSIBLE, ELECTRIC, whether OR not assembled, 
having ALL of the following:
  (a) pump;
  (b) intake AND/OR gas separator;
  (c) protector;
  (d) motor

PUMPS, CENTRIFUGAL, LIQUOR, CONDENSATE AND/OR ACID, ALUMINA 
PROCESSING

PUMPS, SUBSEA, multiphase

PUMPS, CENTRIFUGAL, having a magnetic drive

PUMPS, ACID CIRCULATING, vertical, centrifugal, having ALL of
 the following:
   (a) pumping capacity of between 36 cu m/h and 970 cu m/h, both
       inclusive;
   (b) resistant to 96% OR greater sulphuric acid at temperatures
       of between 50 degrees C and 110 degrees C, both inclusive;
   (c) nickel-chrome impellors, rings and journals;
   (d) steel OR carbon-steel bearings;
   (e) cast iron bearing housings

PUMPS, WATER, SUBMERSIBLE, having ALL of the following:
   (a) 240 V AC power;
   (b) maximum flow output NOT exceeding 4 000 L/h;
   (c) NOT exceeding 90 W

PUMPS, centrifugal, magnetic drive, seal-less, having BOTH of the
 following:
   (a) wetted parts of non-metallic materials;
   (b) synchronous permanent magnets in magnetic drive

PUMPS, cryogenic, operating temperature of -150 degrees C OR below

PUMPS, CENTRIFUGAL, TRASH, self priming, having ALL of the
 following:
   (a) ability to move debris or solids in solution up to and
       inclusive of 50 mm;
   (b) no screens or filters in the solution flow line;
   (c) a suction inlet and discharge outlet of 150 mm

PUMPS, CENTRIFUGAL, TRASH, self priming, imported without a motor or
 engine, having BOTH of the following:
   (a) ability to move debris or solids in solution up to and
       inclusive of 25 mm;
   (b) no screens or filters in the solution flow line

PUMPS, aquarium, with OR without filters attached, having a capacity
 of 1 000 L/h

PUMPS, dewatering, submersible, having ALL of the following:
   (a) either 12 V or 24 V DC operation;
   (b) having a weight NOT exceeding 3.5 kg;
   (c) connection for hoses with internal diameter NOT exceeding
       40 mm;
   (d) suitable for discharge heads up to 3 m;
   (e) having an integral strainer base

PUMPS, CENTRIFUGAL, being EITHER of the following:
  (a) single-stage process pump;
  (b) multi-stage ring section pump

PUMPS, PRODUCED WATER, multi-stage, having BOTH of the following:
  (a) flow rate capacity NOT greater than 223 m3/h;
  (b) working pressure NOT greater than 45 bar

CENTRIFUGAL PUMPS, vacuum, skid mounted, having ALL the 
following:
  (a) vacuum pump;
  (b) submersible water pump;
  (c) air separator tank;
  (d) floater system; 
  (e) control cabinet

PUMPS, CENTRIFUGAL, inline, with OR without motor

PUMPS, END SUCTION, SINGLE STAGE, having ALL of the following:
  (a) working pressure NOT greater than 16 bar;
  (b) direct drive;
  (c) foot mounted motor;
  (d) horizontally mounted

WATER DISTRIBUTORS, cooled AND/OR heated water, including ALL of 
the following:
  (a) centrifugal pumps;
  (b) valves;
  (c) buffer tanks AND/OR expansion vessels;
  (d) pipes,
with OR without ANY of the following:
          (i) sensors;
         (ii) gauges;
        (iii) controllers;
         (iv) filters

PUMP STATIONS, ICE CREAM PRODUCT MANUFACTURING AND/OR COATING, 
mobile, including ALL of the following: 
  (a) stainless steel tank with heated water jacket;
  (b) centrifugal pump;
  (c) sensor

CENTRIFUGAL PUMP SYSTEM, DREDGING, containerised, including all 
of the following:
  (a) closed impeller;
  (b) pump casing;
  (c) shaft cover;
  (d) shaft seal;
  (e) suction cover;
  (f) suction nozzle liner;
  (g) water chamber;
  (h) wearing plates,
with OR without one OR both of the following:
         (i) remote control AND pump control;
        (ii) non-return valve in discharge pipe

PUMPS, END SUCTION, SINGLE STAGE, having ALL of the following:
  (a) working pressure NOT greater than 16 bar;
  (b) direct drive;
  (c) foot mounted flameproof motor;
  (d) horizontally mounted

PUMPS, CENTRIFUGAL, having a canned motor

PUMPS, twin drive booster AND piston type hydraulic submersible, 
including ALL of the following:
  (a) engine power NOT greater than 755 HP; 
  (b) speed NOT greater than 1 800 RPM;
  (c) booster pump power NOT greater than 425 HP;  
  (d) booster pump flow rate 11 360 litres per minute;
  (e) hydraulic submersible pump having a flow rate NOT greater 
      than 360 litres per minute; 
  (f) hydraulic submersible pump operating pressure NOT greater 
      than 4 640 psig;

SETS, WATER PUMP AND ENGINE, trailer mounted, consisting of BOTH 
of the following:
  (a) centrifugal flanged pump having a flow rate NOT less than 
      100 litres per minute and NOT greater than 15 000 litres 
      per minute;
  (b) diesel powered engine having a displacement NOT less than 
      349 cubic centimetres and NOT greater than 6 800 cubic
      centimetres,
with OR without integral fuel tank

PUMPING MACHINES, NATURAL GAS WELL FLUID, skid mounted, whether 
OR not assembled, 
including ALL of the following:
  (a) centrifugal pump;
  (b) valves;
  (c) thrust chamber;
  (d) mechanical seal;
  (e) pressure gauges,
with OR without EITHER of the following:
        (i) pipework;
       (ii) engine

PUMPS, CENTRIFUGAL, vortex, recessed impeller

CHOPPER PUMPS, centrifugal, cast iron AND/OR stainless steel 
casing

PUMPS, CENTRIFUGAL, submersible OR amphibious

LIQUID DISTRIBUTORS, AQUACULTURE FEED MILL, including ALL of the 
following:
  (a) centrifugal pumps;
  (b) positive displacement pumps;
  (c) oil weighing tank;
  (d) oil mixing tanks;
  (e) mixing tanks platform

CENTRIFUGAL PUMPS, POULTRY AND FISH OIL, AQUACULTURE FEED MILL, 
having a pumping capacity NOT greater than 15 m3 per hour

PUMPS, DOUBLE SUCTION CENTRIFUGAL, AXIALLY SPLIT, having ALL of 
the following:
  (a) stainless steel casing AND shaft;
  (b) duplex stainless steel impeller;
  (c) suction size NOT less than 80 mm and NOT greater than 350
      mm;
  (d) discharge size NOT less than 65 mm and NOT greater than
      250 mm;
  (e) impeller diameter NOT less than 553 mm and NOT greater 
      than 645 mm;
  (f) flow rate NOT less than 140 l/s and NOT greater than 300
      l/s

PUMP STATIONS, having ALL of the following:
  (a) pumps;
  (b) expansion tank;
  (c) valves;
  (d) heaters;
  (e) pressure transmitters AND pressure switches;
  (f) temperature sensors

PUMPS, CENTRIFUGAL, including ALL of the following:
  (a) impeller;
  (b) shaft;
  (c) operating air removal capacity NOT greater than 1.5 cubic 
      metres per minute;
  (d) priming system, including ALL of the following:
           (i) priming chamber;
          (ii) swing check valve;
         (iii) vacuum pump,
with OR without EITHER of the following:
           (1) motor;
           (2) base

PUMPS, CENTRIFUGAL, single stage, impeller diameter NOT greater 
than 300 mm

KITS, CONDENSATION CONTROL PUMP, consisting of ALL of the 
following:
  (a) water circulation pump having a power rating NOT less than
      208 V and NOT greater than 230 V;
  (b) check valve;
  (c) copper piping;
  (d) insulation;
  (e) brackets;
  (f) gaskets;
  (g) clamps;
  (h) wiring harness

PUMPS, FUEL, submersible turbine, with OR without stainless 
steel shell, having ALL of the following:
  (a) syphon primer; 
  (b) variable or fixed speed motor NOT less than 0.75 hp and 
      NOT greater than 4 hp;
  (c) thermal overload protection

PUMPS, CENTRIFUGAL, CO-GENERATION BOILER, SUGAR REFINERY PLANT, 
being ANY of the following:
  (a) single stage vertical cooling water;
  (b) multi-stage vertical steam condensate;
  (c) multi-stage horizontal boiler feed water;
  (d) single stage horizontal demineralized water

PUMPS, CENTRIFUGAL, inline, with OR without a mechanical seal, 
having ALL of the following:
  (a) fitted to multi speed canned electrical motor; 
  (b) inlet AND outlet connection thread NOT greater than 32 mm; 
  (c) liquid temperature range NOT less than -10 degrees
      celsius and NOT greater than 110 degrees celsius

CENTRIFUGAL PUMPS, chemical, incorporating a mechanical seal, 
with OR without the following:
  (a) strainer OR priming unit;
  (b) gauge;
  (c) non-return valve;
  (d) by-pass;
  (e) control valve

WATER AND SLUDGE STORAGE UNIT, ROAD SWEEPER RECYCLING PLANT, 
including ALL of the following:
  (a) containerised water AND buffer tank;  
  (b) air flotation lightweight removal system;
  (c) sludge recirculation pump AND pipework;
  (d) water recycle pump AND motor;
  (e) water AND buffer tank level measuring probe;
  (f) steel support structure AND accessibility structures

END SUCTION PUMPS, incorporating a screw centrifugal impeller, 
including ALL of the following:
  (a) impeller mounted taper shaft;
  (b) suction cone AND/OR liner;
  (c) bearing frame unit including ANY one OR more of the
      following:
          (i) back cover;
         (ii) back cone;
        (iii) back plate

PUMPS, skid OR trailer mountable, pod enclosed, having ALL of 
the following:
  (a) centrifugal pump;
  (b) pump primer;
  (c) sound reducing canopy;
  (d) control panel;
  (e) vacuum pump with coalescer filter;
  (f) dry weight NOT greater than 1 350 Kg;
  (g) diesel engine

PUMPS, SEAWATER, AXIALLY SPLIT, SINGLE STAGE, DOUBLE SUCTION, 
including ALL of the following:
  (a) super duplex stainless steel casing, shaft AND impeller;
  (b) suction size NOT less than 800 mm and NOT greater than 1 
      100 mm;
  (c) discharge size NOT less than 600 mm and NOT greater than 
      900 mm;
  (d) impeller diameter NOT less than 800 mm and NOT 
      greater than 1 200 mm;
  (e) flow rate NOT less than 5 000 m3/h and NOT greater 
      than 15 000 m3/h

CENTRIFUGAL PUMPS, SPLIT CASING, skid mounted, with OR without 
motor, including ALL of the following:
  (a) stainless steel impeller AND shaft;
  (b) externally removable bearing housing;
  (c) serrated casing wear rings;
  (d) double row thrust bearing assembly

PUMPS, BOILER FEED, HORIZONTAL OR VERTICAL, RADIALLY SPLIT, 
MULTI-STAGE RING SECTION WITH RADIAL IMPELLERS, having BOTH of 
the following:
  (a) maximum flow rate NOT exceeding 1 450 m3/h;
  (b) operating pressure NOT greater than 420 bar

PUMPS, MULTISTAGE, having ALL of the following:
  (a) pump size NOT greater than 200 mm;
  (b) flow rate capacity NOT greater than 1 100 m3/h;
  (c) working pressure NOT greater than 300 bar

PUMPS, RING SECTION, multistage, having ALL of the following:
  (a) pump sizes NOT less than 25 mm and NOT greater than 200 mm;
  (b) capacity NOT greater than 1 100 m3/h;
  (c) working pressure NOT greater than 100 bar;

PUMPS, SCREW CENTRIFUGAL, whether OR not assembled, including 
ALL of the following:
  (a) suction cone;
  (b) screw impeller;
  (c) submersible electric motor

PUMPS, centrifugal, incorporating canned motor, having ANY of 
the following:
  (a) flow rate of 59.5 m3/hour and head of 72.1 m;
  (b) flow rate of 10.8 m3/hour and head of 95.9 m;
  (c) flow rate of 16.5 m3/hour and head of 45 m;
  (d) flow rate of 11.1 m3/hour and head of 96 m;
  (e) flow rate of 6 m3/hour and head of 156 m;
  (f) flow rate of 6.8 m3/hour and head of 160 m;
  (g) flow rate of 9.9 m3/hour and head of 100 m
For the purposes of this order, tolerances allowable for 
specifications (a) to (g) are +/- 5%

PUMPS, centrifugal, vertical multistage, having ALL of the 
following:
  (a) in line suction AND discharge;
  (b) stainless steel hydraulic parts;
  (c) volume flow rate NOT greater than 110 m3/h;
  (d) suction AND discharge diameter NOT less than 32 mm and
      NOT greater than 100 mm

INSULATING OIL PUMPS, TRANSFORMER AND RECTIFIER, centrifugal, 
having an operating temperature NOT less than -10 degrees 
Celsius and NOT greater than 100 degrees Celsius

SEWAGE AND/OR OILY WATER PUMPING STATIONS, including ALL of the 
following:
  (a) sumps;
  (b) macerating centrifugal pumps;
  (c) discharge pipes;
  (d) control panels

SETS, PUMP, with OR without sound attenuating canopy, including 
ALL of the following:
  (a) centrifugal pump;
  (b) diaphragm vacuum pump;
  (c) diesel engine;
  (d) control panel

PUMPS, CONDENSATE, AIR CONDITIONING, with OR without float switch

PUMPS, CENTRIFUGAL, being EITHER of the following;
  (a) pickle acid circulation;
  (b) spent pickle acid liquor

PUMPS, WASHING MACHINE, DRAINAGE, incorporating a shaded pole 
electric motor

PUMPS, DREDGING, submersible, comprising BOTH of the following:
  (a) excavating heads;
  (b) hydraulic power pack

PUMPS, CENTRIFUGAL, draining, having BOTH of the following:
  (a) asynchronous motors;
  (b) motor stack length NOT greater than 40 mm

PUMPS, WATER, constant pressure, centrifugal, 240 V having ALL 
of the following:
  (a) 800 W sealed motor;
  (b) overheat temperature cut out switch;
  (c) flow rate NOT more than 60 L/min

PUMPS, SLURRY, PIPELINE, horizontal, having inlet dimensions NOT 
less than 50 mm and NOT greater than 500mm

PUMPS, DRAIN, having ALL of the following:                       
  (a) synchronous motor;                                         
  (b) motor stack length NOT less than 20 mm and NOT greater than
      35 mm;                                                     
  (c) water flow rate NOT less than 7 litres per minute and NOT  
      greater than 30 litres per minute, with a one metre head of
      water

PUMPS, DRAINAGE OR SEWAGE, submersible centrifugal, discharge
 outlet NOT less than 30 mm

PUMPS, SUBMERSIBLE, comprising ALL of the following:
   (a) synchronous magnetic impeller;
   (b) capacity of 3 950 L/h to 8 050 L/h;
   (c) motor output NOT exceeding 2 kW

PUMPS, live fish transfer, having EITHER of the following pumping
 actions:
   (a) helical case with integral single cup shaped impeller;
   (b) vacuum/pressure action

CHAINSAW OIL PUMPS

EJECTOR PUMPS, AMMONIA AND CARBAMATE  SOLUTION, with OR without 
the following:
  (a) pneumatic diaphragm actuator;
  (b) pneumatic positioner;
  (c) electro-pneumatic positioner;
  (d) filter reducing station

PUMPS, DOSING, UREA, including ALL of the following:
  (a) operating voltage NOT less than 9 V and NOT greater than 
      16 V;
  (b) urea flow rate of NOT less than 75 ml/h and NOT greater 
      than 7 500 ml/h;
  (c) doser inlet operating air pressure NOT less than 6 bar  
      and NOT greater than 12 bar; 
  (d) suction port screen

GEROTOR SETS, inner or outer, hydraulic pump

SUCKER RODS, diameter 15.8 mm to 22.3 mm (5/8" to 7/8"), length
 7.62 m (25 ft)

PARTS, PUMP JACK, with OR without sheaves, whether OR not 
assembled, including ALL of the following:
  (a) wire line;
  (b) saddle bearing;
  (c) wrist pin bearing;
  (d) equaliser bearing;
  (e) horse head;
  (f) walking beam;
  (g) samson post;
  (h) equaliser beam;
  (i) pitman arms;
  (j) crank pin;
  (k) gear reducer;
  (l) brake assembly;
  (m) guards;
  (n) crank arm

PARTS, OIL AND GAS WELL PUMP, being polished rods

PARTS, OIL AND GAS WELL PUMP, being sucker rods

PARTS, OIL FIELD PUMP, being pump jacks

PARTS, DISPLACEMENT PUMP, piston diaphragm positive, double 
acting, being ANY of the following:
  (a) suction and discharge air pressure vessels;
  (b) suction and discharge valve housings;
  (c) suction and discharge pipes;
  (d) diaphragms;
  (e) housings;
  (f) covers;
  (g) elbows;
  (h) piston rods;
  (i) air pressure vessel connector assemblies, including ALL 
      of the following:
          (i) valves;
         (ii) flanges;
        (iii) pressure transmitters and containers;
         (iv) gaskets;
          (v) supports;
         (vi) plates;
        (vii) clamps;
       (viii) clips;
         (ix) pipes;
          (x) fittings;
         (xi) screws;
         (xii) nuts;
        (xiii) washers;
         (xiv) housings;
          (xv) hose lines

PARTS, PLUNGER PUMP, reciprocating horizontal quintuplex, 
positive displacement, hydraulic, being ANY of the following:
  (a) heads;
  (b) crank mechanisms;
  (c) rods;
  (d) crossheads;
  (e) push rods;
  (f) flanges;
  (g) covers;
  (h) tabs;
  (i) tongues;
  (j) shafts;
  (k) plugs;
  (l) piston blocks or frames;
  (m) cylinders;
  (n) plungers;
  (o) support rings;
  (p) spacer rings;
  (q) pistons

PARTS, PERISTALTIC HOSE PUMP, being ANY of the following:
   (a) pump housings;
   (b) pump covers;
   (c) rotors;
   (d) pump shafts;
   (e) shims;
   (f) pressing shoes;
   (g) joint rings;
   (h) inspection windows;
   (i) inserts;
   (j) bearing covers;
   (k) bushes;
   (l) pins;
   (m) flange brackets;
   (n) flanges;
   (o) breather caps;
   (p) mounting supports

PARTS, CRYOGENIC PUMPS, operating temperature of -150 degrees C
 OR below, being ANY of the following:
   (a) case wear ring;
   (b) impeller wear ring;
   (c) impeller;
   (d) stuffing box;
   (e) guide wheel;
   (f) packing set;
   (g) lock pin;
   (h) compensator sleeve

PISTON ASSEMBLY, BENT AXIS FIXED DISPLACEMENT HYDRAULIC PUMP,
 comprising BOTH of the following:
   (a) piston;
   (b) rings

CHAINSAW OIL PUMP PARTS, being ANY of the following:
   (a) pump piston;
   (b) roll pin;
   (c) plug;
   (d) hose;
   (e) spline screw;
   (f) worm;
   (g) control bolt;
   (h) elbow connector;
   (i) pick up body

PARTS OF DIESEL ENGINE PUMPS, being parts of EITHER of the
 following:
   (a) water pumps;
   (b) oil pumps

CARTRIDGES, hydraulic vane pump type, which include ALL of the
 following items:
   (a) cam ring;
   (b) rotor;
   (c) vanes;
   (d) side plates;
   (e) pins

PARTS, IMPELLER PUMP, AUTOMOTIVE FUEL, being ANY of the following:
   (a) outlet plates;
   (b) spacer plates;
   (c) impellers;
   (d) brush carriers;
   (e) armatures having a current draw NOT greater than 10 amps

PARTS, AXIAL PISTON PUMP, being piston pads

PARTS, PUMPS, being ANY of the following:
  (a) seal housing cover;
  (b) diffuser; 
  (c) shock absorbers

PARTS, PUMPS, being ANY of the following:
  (a) impeller;
  (b) suction cover;
  (c) o-rings; 
  (d) fasteners

PARTS, PROGRESSIVE CAVITY PUMP, being coupling rods

PARTS, PUMP, being shafts whether OR not flexible with OR 
without rotor

PARTS, INJECTION PUMPS, being ANY of the following:
  (a) housings;
  (b) piston rods;
  (c) injection stems;
  (d) o-ring seats

PARTS, CENTRIFUGAL PUMP, SINGLE VANE SCREW IMPELLER, assembled 
OR unassembled, being ANY of the following:
  (a) volute casings;
  (b) impellers;
  (c) impeller flanges;
  (d) suction covers;
  (e) suction casings;
  (f) shims;
  (g) liners;
  (h) back cones

PARTS, DRUM AND CONTAINER PUMP, being ANY of the following:
  (a) coupling;
  (b) discharge connectors;
  (c) drive shafts;
  (d) gas AND vapour emission adapters;
  (e) guide sleeves;
  (f) hand wheels;
  (g) impellers;
  (h) inner AND/OR outer tubes;
  (i) pump feet;
  (j) pump housing including carbon bushing;
  (k) rotors;
  (l) strainers

COMBINED LABYRINTH SEAL AND POSITIVE SEAL MODULAR ELECTRIC MOTOR 
PROTECTORS, SUBMERSIBLE PUMP, whether OR not assembled, 
with OR without thrust bearings, including ALL of the following:
  (a) labyrinth chambers;
  (b) positive-seal sections;
  (c) bearings;
  (d) seals

PARTS, RECIPROCATING POSITIVE DISPLACEMENT PUMP, being fluid end 
assemblies whether OR not assembled including ALL of the 
following:
  (a) fluid end;
  (b) retainers;
  (c) covers;
  (d) o-rings;
  (e) rings;
  (f) valve springs;
  (g) bolts AND/OR nuts;
  (h) adapters;
  (i) plungers AND/OR pistons;
  (j) clamps;
  (k) packing seals;
  (l) packing brass;
  (m) seats

PARTS, PUMP, being stainless steel pump housings

PARTS, PRESSURE PUMP, being pressurised pump heads

PARTS, DIESEL ENGINE, OIL OR WATER PUMPS, being ANY of the
 following:
   (a) body;
   (b) cover;
   (c) impeller;
   (d) repair kit incorporating a spacer, impeller and shaft;
   (e) support

PARTS, CENTRIFUGAL PUMP, being EITHER of the following:
  (a) heat recovery shells;
  (b) suction covers

PARTS, PUMPING UNIT, ANTI-LOCK BRAKING SYSTEM(ABS), being ANY of 
the following:
  (a) reciprocating pump elements;
  (b) pump element piston guide rings;
  (c) pump housing;
  (d) accumulator pistons;
  (e) covers

PARTS, CENTRIFUGAL PUMPS, being rotating exchange units 
comprising ALL of the following:
  (a) impellers;
  (b) bearings;
  (c) mechanical seals;
  (d) rubber seals;
  (e) shafts

PARTS, BOILER CIRCULATING PUMP, being ANY of the following:
  (a) journal tilting pads;
  (b) journal sleeves;
  (c) thrust discs;
  (d) thrust plates;
  (e) impeller wear rings

PARTS, PUMP, being ANY of the following:
   (a) bushings;
   (b) adapters;
   (c) mufflers;
   (d) centre sections;
   (e) pistons;
   (f) liquid chambers;
   (g) air chambers;
   (h) tee sections;
   (i) elbows;
   (j) valve seat;
   (k) sleeves;
   (l) manifolds;
   (m) studs;
   (n) nipples;
   (o) end caps;
   (p) retainers;
   (q) sleeve and spool kits, comprising ALL of the following:
           (i) sleeves;
          (ii) spools;
         (iii) gaskets,
   (r) diaphragms;
   (s) housings;
   (t) snap rings;
   (u) centre blocks;
   (v) handles;
   (w) impellers;
   (x) rotors;
   (y) stators;
   (z) idlers;
  (aa) circlips;
  (ab) feet;
  (ac) shims;
  (ad) inserts;
  (ae) idler pins;
  (af) plates;
  (ag) wet end kit, comprising ALL of the following:
           (i) diaphragms;
          (ii) valve seat;
         (iii) balls,
  (ah) capillary rods;
  (ai) pedestals;
  (aj) diaphragm rods;
  (ak) neck rings

PARTS, BOILER CIRCULATING PUMP, being ANY of the following:
  (a) stators;
  (b) rotors;
  (c) impellers;
  (d) terminal glands

PARTS, CENTRIFUGAL PUMP, flanged, being EITHER of the following:
  (a) impellers; 
  (b) casing covers

PARTS, CENTRIFUGAL PUMP, having a pressure rating of NOT less 
than 300 bar, being EITHER of the following:
  (a) multistage impeller assemblies;
  (b) single stage impellers

PARTS, PUMP, CENTRIFUGAL, FLANGED, mag drive and/or hygienic,
being ANY of the following:
  (a) casings;
  (b) impellers;
  (c) mag capsules;
  (d) foot plates;
  (e) rings;
  (f) flanges

VOLUTE CASINGS, CENTRIFUGAL FLANGED PUMP

PARTS, IMPELLER PUMP, AUTOMOTIVE FUEL, being ANY of the following:
   (a) outlet plates;
   (b) spacer plates;
   (c) impellers;
   (d) brush carriers;
   (e) armatures having a current draw NOT greater than 10 amps

PARTS, ROTARY VANE PUMP, being ANY of the following:
   (a) housings;
   (b) vanes;
   (c) rotors;
   (d) liners;
   (e) pins;
   (f) acorn nuts;
   (g) pressure adjustment screws;
   (h) gaskets;
   (i) retaining rings;
   (j) name plates;
   (k) align pins;
   (l) relief valves;
   (m) relief valve springs;
   (n) caps;
   (o) slingers;
   (p) pistons

VACUUM PUMPS, including ALL of the following:
  (a) steam jet ejectors;
  (b) surface condensers;
  (c) piping,
with OR without ANY of the following:  
          (i) flanges;
         (ii) adjusting plates;
        (iii) bolts;
         (iv) nuts;
          (v) gaskets

VACUUM PUMPS, DC, with OR without ANY of the following:
  (a) adapters;
  (b) batteries;
  (c) battery chargers;
  (d) cases;
  (e) hoses;
  (f) oil;
  (g) shoulder belts;
  (h) valves with OR without vacuum gauge

SKIDS, VACUUM PUMP, unassembled, having ALL of the following:
  (a) liquid ring vacuum pump complying with directive 
      2014/34/EU, relating to equipment and protective systems 
      intended for use in potentially explosive atmospheres, 
      of the European Parliament and of the Council (2014);      
  (b) cooler;
  (c) motors;
  (d) separator vessel;
  (e) nozzles;
  (f) valves;
  (g) piping;
  (h) temperature transmitter;
  (i) level transmitter;
  (j) magnetic level

PUMPS, vacuum, turbo molecular type, having an ultimate
 vacuum of 0.000001 torr or greater, when imported separately
 without gauges, controls, backing pumps, and ALL other
 ancillary equipment required to make-up a complete vacuum
 pumping package assembly

VACUUM PUMPS, SANDWICH DIAPHRAGM, with OR without ANY of the 
following:
  (a) base plate;
  (b) inlet catch pot;
  (c) glass emission condenser;
  (d) vacuum controller

VACUUM PUMPS, DIAPHRAGM, having EITHER of the following:
  (a) structure OR zone diaphragm;
  (b) polytetrafluoroethylene OR polyphenylene sulfide cylinder 
      head,
with OR without ANY of the following:
      (i) base plate;
     (ii) inlet catch pot;
    (iii) glass emission condenser;
     (iv) vacuum controller

PUMPS, vacuum, liquid ring

PUMPS, vacuum, being oil vapour diffusion, or cryopumps having an
 ultimate vacuum of 0.001 torr OR greater

PUMPS, ION

PUMPS, vacuum, turbo molecular type, having an ultimate vacuum
 of 0.000001 torr OR greater

PUMPS, vacuum, compressed air operated, multi-chamber venturi
 units

PUMPS, vacuum, rotary vane, having a capacity exceeding 60 cu m/h

PUMPS, vacuum, liquid ring, having EITHER of the following:
   (a) capacity of 8 000 cu m/h or greater;
   (b) capacity of 1 000 cu m/h or greater at an ultimate
       operating vacuum in the range of - 66 kPa to - 100 kPa
       (both inclusive)

PUMPS, ROTARY VACUUM, oil free, having ALL of the following:
   (a) vacuum range from 33 mbar (1" Hg) to 982 mbar (29.6" Hg);
   (b) motor driven

VACUUM PUMPS, linear motor driven, free piston operation

VACUUM PUMPS, being dry running positive displacement rotary pumps
 incorporating multiple claw-type stages and at least one rotary lobe
 (roots) stage

TEST KITS, vacuum, automotive component, hand operated

PUMPS, vacuum, industrial, DC powered, 12 V

PUMPING STATIONS, VACUUM, having ALL the following:
  (a) turbo-molecular pump with integrated drive;
  (b) backing pump;
  (c) pumping station control;
  (d) control cables

VACUUM PUMPS, screw type, having a capacity NOT less than 60 
cubic metres per hour

VACUUM PUMPS, hand operated, including EITHER of the following:
  (a) bottle stoppers;
  (b) bottle stoppers AND bottle pourers

VACUUM PUMPS, hand operated, with OR without sealable plastic 
containers

PUMPS, VACUUM, having BOTH of the following:
  (a) power consumption NOT greater than 80 W;
  (b) final vacuum pressure NOT greater than 40 mbar

VACUUM PUMPS, 12 V DC

PUMPS, VACUUM, VAPOUR RECOVERY, piston driven, reciprocating 
positive displacement

COMPRESSORS, refrigeration or air conditioning, whether or not
 imported with an electric motor, but NOT including:
   (a) open drive reciprocating compressors, having a swept
       volume of less than 20 L/s;
   (b) reciprocating hermetic compressors, having a swept
       volume exceeding 0.78 L/s but NOT exceeding 3.8 L/s;
   (c) semi-hermetic reciprocating compressors, having a swept
       volume of less than 15 L/s

COMPRESSORS, cryogenic refrigerant

COMPRESSORS, refrigeration or air-conditioning, hermetic,
 having a swept volume NOT exceeding 0.78 L/s
   For the purposes of TC 8632590 "swept volume" is calculated
   as follows for:
     (a) reciprocating compressors:
         - the area of the bore x stroke of the piston x
           published nominal speed x number of cylinders;
     (b) rotary slide vane compressors and compliant scroll
         compressors:
         - the published displacement/r x published nominal speed

COMPRESSORS, refrigeration or air-conditioning, sealed
 hermetic or welded hermetic, rotary fixed vane, having a
 swept volume exceeding 0.68 L/s but NOT exceeding 1.68 L/s
   For the purposes of TC 8534087:
     (a) semi-sealed, semi-hermetic or accessible compressors
         are NOT admissible under this Order;
     (b) "swept volume" is calculated from the published
         displacement/r x the published nominal speed

COMPRESSORS, refrigeration or air-conditioning, sealed
 hermetic or welded hermetic, having a swept volume
 exceeding 3.8 L/s
   For the purposes of TC 8530356:
     (a) semi-sealed, semi-hermetic or accessible compressors
         are NOT admissible under this Order;
     (b) "swept volume" is calculated as follows for:
           (i) reciprocating compressors:
               - the area of the bore x stroke of the
                 piston x published nominal speed x number of
                 cylinders;
          (ii) rotary slide vane compressors and compliant scroll
               compressors:
               - the published displacement/r x published nominal
                 speed

COMPRESSORS, REFRIGERATION OR AIR CONDITIONING, reciprocating,
 hermetic, having a swept volume exceeding 0.78 L/s but NOT
 exceeding 3.80 L/s

COMPRESSORS, REFRIGERATION OR AIR CONDITIONING, hermetic, with a
 swept volume NOT exceeding 0.78 L/s

COMPRESSORS, MOTOR VEHICLE AIRCONDITIONING

COMPRESSORS, RECIPROCATING, REFRIGERATION OR AIR CONDITIONING,
 whether or not imported with an electric motor, being EITHER of the
 following:
   (a) open drive, having a swept volume of NOT more than 20 L/s;
   (b) semi-hermetic, having a swept volume of NOT more than 15 L/s

COMPRESSORS, refrigeration or air-conditioning, scroll type,
 hermetically sealed, having a swept volume exceeding 1.5 L/s
 but NOT exceeding 3.6 L/s
   For the purposes of TC 9409422 "swept volume" is calculated from
   the published displacement/r x the published nominal speed

COMPRESSORS, refrigeration or air conditioning, open drive,
 reciprocating, with capacity control via unloading of one or more
 cylinders

COMPRESSORS, semi hermetic, refrigeration, complete with electric
 motor (stator) which is isolated from the refrigerants by a steel
 separation hood

COMPRESSORS, refrigeration or air conditioning, semi hermetic,
 reciprocating, with capacity control via unloading of one or more
 cylinders

COMPRESSORS, REFRIGERATION, hermetically sealed

COMPRESSORS, REFRIGERATOR AND/OR FREEZER AND/OR AIR CONDITIONER, 
semi-hermetic

COMPRESSORS, REFRIGERATION, CENTRIFUGAL, swept volume
 exceeding 70 litres/second

COMPRESSORS, REFRIGERATION OR AIR CONDITIONING, hermetically
 sealed, having a swept volume NOT less than 1.5 L/s but
 NOT exceeding 12.0 L/s

AIR COMPRESSORS, wheeled chassis, towable, having a capacity NOT 
greater than 3 cubic meters per minute

AIR COMPRESSORS, chassis mounted, with OR without wheels AND/OR 
tyres AND/OR cooling units, having ALL of the following:
  (a) diesel engine;
  (b) screw air end;
  (c) free air delivery nominal capacity NOT less than 3 m3/min 
and NOT greater than 25 m3/min

AIR COMPRESSORS, wheeled chassis, towable, having a capacity 
exceeding 3 cubic metres but NOT exceeding 25 cubic metres of 
free air delivered per minute

FANS, ceiling, solar or DC operated

GEL FRAGRANCE DISPENSER, fan operated, battery powered

FANS, wall mounted, with self contained electric motors of an output
 NOT exceeding 125 W, but excluding exhaust fans of all kinds

FANS, ceiling, with self contained electric motors of an output
 NOT exceeding 125 W, but excluding exhaust fans of all kinds

FANS, box, desk and pedestal, with self contained electric motors
 of an output NOT exceeding 125 W, but excluding exhaust fans
 of all kinds

EXHAUST FAN UNITS, including ALL of the following:
  (a) rated operational voltage NOT greater than 250 V AC;
  (b) air flow NOT greater than 600 cubic metres per hour;
  (c) impeller having a diameter NOT greater than 250 mm;
  (d) motor having an output NOT greater than 45 W;
  (e) wall OR window OR ceiling mounted

EXHAUST FANS, wall OR window OR ceiling mounted, having ALL 
of the following:
  (a) rated voltage NOT greater than 250 VAC;
  (b) air flow NOT less than 360 m3/h and NOT greater than 
      600 m3/h;
  (c) impeller diameter NOT greater than 250 mm;
  (d) power consumption NOT greater than 45 W

FANS, MISTING, portable, having ALL of the following:
  (a) weight (excluding liquid) of NOT greater than 10 kg;
  (b) electric motor output NOT exceeding 125 W;
  (c) water dispersing atomizer

EXHAUST FANS, solar, having a motor output NOT greater 
than 100 W

MISTING FANS, mobile, having ALL of the following:
  (a) water pump;
  (b) electric motor;
  (c) water reservoir;
  (d) wheels AND/OR castors

EXHAUST FANS, ceiling, having a motor output of NOT less than 30 
W and NOT greater than 35 W

EXHAUST FANS, ceiling, having a motor output of NOT less than 
50 W and NOT greater than 125 W

FANS, COOLING, domestic, having BOTH of the following:
   (a) self contained electric motor NOT exceeding 125 Watts;
   (b) weight NOT exceeding 7 kg,
 but NOT including exhaust fans of any kind

BLOWERS, rotary lobe type, positive displacement, having a
 capacity exceeding 100 cu m/h with bare shaft

FANS, cooling tower or heat exchanger, having a dia exceeding
 6.5 m

BLOWERS, air, pipe organ

BLOWER/SUCTION UNITS, textile machinery, travelling
 overhead type

FANS, FLUE GAS

FANS, incorporating suction pad OR lanyard, battery powered

FANS, OSCILLATING, 12 V

VENTILATORS, CONVECTION, having ALL of the following:
   (a) self propelled fan, air movement AND/OR pressure change
       activated;
   (b) two way air flow;
   (c) window AND/OR wall mounted

FANS, tube axial, incorporating an integral motor, with an
 impeller diameter less than 100 mm

SIDE CHANNEL BLOWERS

FANS, crossflow, having ALL of the following features:
   (a) NOT less than 60 mm and NOT greater than 120 mm diameter of
       fan impeller;
   (b) NOT less than 260 mm and NOT greater than 1 180 mm in length;
   (c) powered by an external rotor motor;
   (d) fully speed controllable;
   (e) airflow 90 or 180 degree relative to air inlet
   (f) voltage of 220 V or greater but NOT exceeding 440 V AC supply

FANS, centrifugal, having ALL of the following features:
   (a) backward curve impeller;
   (b) single inlet;
   (c) NOT less than 133 mm and NOT greater than 280 mm diameter
       of fan impeller;
   (d) powered by an external rotor motor;
   (e) automatic thermal cut out;
   (f) fully speed controllable;
   (g) voltage of 220 V OR greater but NOT exceeding 440 V AC supply

FANS, floor standing and pedestal, with self contained electric
 motors of an output NOT exceeding 200 W, but excluding exhaust
 fans of all kinds

ASSEMBLIES, FAN, EVAPORATORS AND/OR CONDENSERS, DOMESTIC 
REFRIGERATOR, having ALL of the following:
  (a) motor power consumption NOT less than 4 watts and NOT
      greater than 9 watts;
  (b) blade pitch NOT less than 12 mm and NOT greater than 45 mm;
  (c) shroud diameter NOT greater than 255 mm

BLOWERS, STEELSTRIP METAL COATING LINE, with OR without 
silencers AND/OR filters, including ANY of the following;
  (a) furnace post combustion; 
  (b) furnace premix; 
  (c) gas jet cooling

FANS AND/OR BLOWERS, STEELSTRIP METAL COATING LINE, with OR 
without silencers, including ANY of the following:
(a) fans, exhaust, including EITHER of the following:
          (i) water quench mist;
         (ii) furnace waste gas,
(b) blowers, air, including ANY of the following:
          (i) waste gas dilution;
         (ii) furnace ignition;
        (iii) furnace combustion;
         (iv) water quench drying;
          (v) steel strip cooling

FANS, RADIAL, having ALL of the following:
  (a) gas operated;
  (b) mass flow NOT greater than 60 000 kg/h;
  (c) volume flow NOT less than 10.0 m3/sec;
  (d) interconnecting ductwork

BLOWERS, POSITIVE DISPLACEMENT, having ALL of the following:
  (a) volume flow NOT less than 9 600 m3/h;
  (b) motor output NOT less than 400 kW;
  (c) sound pressure NOT greater than 82 decibels

FANS, CENTRIFUGAL, having ALL of the following:
  (a) impeller wear plates;
  (b) inlet wear protection;
  (c) fan casing;
  (d) motor rating NOT less than 130 kW

EXHAUST FAN MODULES, DATA CENTRE, including ALL of the following:
  (a) exhaust airflow NOT greater than 144 360 m3/h;
  (b) electronically commutated fans;
  (c) insulated panels;
  (d) dampers

VACUUM BLOWERS, having ALL of the following:
  (a) single stage;
  (b) airflow NOT less than 200 m3/min and NOT greater than 
      850 m3/min;
  (c) servo pneumatic motor controlled steplessly adjusted 
      diffuser blades with vacuum variable volume flow

FANS, SUCTION AND/OR EXTRACTION, WOOD CHIP PROCESSING, with OR 
without a rotary valve filter

FANS, recirculating AND/OR radial, having ANY one OR more of the 
following: 
  (a) mounts AND/OR mounting bases;
  (b) operating speed NOT greater than 1 451 RPM;
  (c) impeller diameter NOT greater than 991 mm;
  (d) fan unit height NOT greater than 1 926 mm

FANS, CENTRIFUGAL, direct driven, having a voltage NOT less than 
400 V AC

ROTARY BLOWERS, having BOTH of the following: 
  (a) flow rate NOT less than 200 m3/per hr and NOT greater than 
      500 m3/per hr;
  (b) pressure NOT greater than 1 000 mbar(g)

BLOWERS, ROTARY LOBE, enclosed, having an input airflow NOT less 
than 3 000 m3/hr

AERATION BUNKER COMPONENTS, being ALL of the following:
  (a) floor aeration unit;
  (b) plastic spigot pipes;
  (c) steel fan;
  (d) distribution duct; 
  (e) suction control units;
  (f) control unit AND sensors AND frequency drive; 
  (g) oxygen monitoring panel AND sensors

DRYERS, AQUACULTURE FEED MILL, including ALL of the following:
  (a) elevators;
  (b) cyclones;
  (c) rotary valves;
  (d) exhaust air fans;
  (e) ducting;
  (f) density measuring unit with moisture module

DRYERS, AQUACULTURE FEED MILL, including ALL of the following:
  (a) elevators;
  (b) cyclones;
  (c) rotary valves;
  (d) exhaust air fans;
  (e) ducting;
  (f) density measuring unit with moisture module

SUCTION HOODS, UNCURED CONCRETE PARTICLE, having ALL of the 
following:
  (a) centrifugal fan capacity NOT less than 1 000 kg/cubic
      metre;
  (b) plastic coated hood;
  (c) ventilation control valve;
  (d) silencer;
  (e) cyclone filter

FANS AND/OR BLOWERS, DC OR AC, axial OR radial OR crossflow 
type, having ANY one OR more of the following:
  (a) sleeve OR ball OR magnetic bearings;
  (b) DC operating voltage NOT less than 5 V and NOT greater 
      than 48 V;
  (c) AC operating voltage NOT less than 115 V and NOT greater 
      than 240 V;
  (d) maximum speed exceeding 1 000 RPM;
  (e) diameter NOT greater than 300 mm;
  (f) height NOT greater than 300 mm;
  (g) length NOT greater than 300 mm,
with OR without filters

RADIAL FANS, GERMINATING AND/OR KILNING VESSEL AND/OR STEEPING 
VESSEL, having BOTH of the following:
  (a) volume flow rate of NOT less than 6 000 m3/h and NOT
      greater than 330 400 m3/h;
  (b) three phase electric motor

HAND DRYERS, AIR PRESSURE, having ALL of the following:
  (a) polypropylene filter;
  (b) airflow speed switch;
  (c) heater setting switch;
  (d) upper AND lower optical sensors;
  (e) airflow rate NOT less than 98 m/s and NOT greater 
      than 110 m/s;
  (f) brushless motor capacity NOT less than 19 400 RPM
      and NOT greater than 20 900 RPM

DOORWAY AIR BLOWING MACHINES, single phase, having ALL of the 
following:
  (a) width NOT less than 900 mm and NOT greater than 1 190 mm;
  (b) rectification plate OR multiple nozzles;
  (c) multiple propeller fans

HAND DRYERS, electric, having ALL of the following:
  (a) air filter;
  (b) motion sensors;
  (c) air speed NOT less than 110 m/s

MOTORS, VACUUM CLEANER, one stage OR two stage OR three stage,  
having BOTH of the following:
  (a) power consumption NOT less than 0.746 kW and NOT greater 
       than 1.9 kW;
  (b) speed NOT less than 12 000 rpm

FANS, WIND TURBINE CONVERTER VENTILATION AND TEMPERATURE 
CONTROL, with OR without filters

ASSEMBLIES, FAN, REFRIGERATOR EVAPORATOR AND/OR CONDENSER,  
including ALL of the following:
  (a) fan motor;
  (b) fan blades;
  (c) fan shroud

BLOWERS, STEEL STRIP COATING LINE, centrifugal, multi-stage

MISTING FANS, mobile, having ALL of the following:
  (a) water pump;
  (b) misting controller;
  (c) water reservoir;
  (d) wheels AND/OR castors

FANS, AXIAL, having ALL of the following:
  (a) plate mount and or cylindrical case mount;
  (b) IP65 enclosures;
  (c) overload protection;
  (d) side profile depth NOT greater than 285 mm

VENTILATION CONTROL SYSTEM, POULTRY SHED, programmable logic 
controlled, comprising BOTH of the following:
  (a) fans;
  (b) vents

FANS, AXIAL, adjustable pitch, having ALL of the following:
  (a) fibre reinforced polyester or aluminium blades;
  (b) high tensile steel blade to hub connectors;
  (c) diameter NOT greater than 12.2 m

FILTER-VENTILATORS, PROTECTIVE ENCLOSURE, with OR without fans

FANS, AXIAL, adjustable pitch, having ALL of the following:
  (a) fibre reinforced polyester blades;
  (b) high tensile steel blade to hub connectors;
  (c) diameter NOT greater than 6.7 m

FANS, HEAT PUMP

FANS, CENTRIFUGAL, voltage NOT less than 415 V AC, being EITHER 
of the following:
  (a) direct driven;
  (b) belt driven

BLOWERS, HIGH PRESSURE, having a flow rate NOT less than 500 
cubic metres per hour

FAN ASSEMBLIES, DOMESTIC OVENS AND/OR COOKTOPS, comprising BOTH 
of the following:
  (a) fans;
  (b) motors

FANS, AXIAL, TUNNEL VENTILATION, having ALL of the following:
  (a) direct drives;
  (b) flow rate NOT less than 65 cm3/s;
  (c) diameter NOT less than 1 800 mm

FANS, JET, TUNNEL having ALL of the following:
  (a) maximum vertical dimension NOT less than 900 mm;
  (b) maximum motor rating NOT less than 30 kW;
  (c) thrust NOT less than 850 N

FANS, INDUSTRIAL, having BOTH of the following:
  (a) wheel diameter NOT less than 150 mm and NOT greater than   
      1 600 mm; 
  (b) maximum total pressure NOT less than 900 pascals and NOT 
      greater than 4 000 pascals

FANS, centrifugal, 240 V AC, having ALL of the following:
  (a) forward curve impellers;
  (b) external rotor motors;
  (c) fan speed NOT less than 700 rpm

FANS, floor standing and pedestal, with self contained electric 
motor of an output NOT exceeding 250 W

ASSEMBLIES, FAN, EVAPORATORS AND/OR CONDENSERS, DOMESTIC 
REFRIGERATOR, having ALL of the following:
  (a) motor power consumption NOT less than 4 watts and NOT
      greater than 9 watts;
  (b) blade pitch NOT less than 12 mm and NOT greater than 45 mm;
  (c) shroud diameter NOT greater than 255 mm

FANS, WATER SPRAY, hand held, plastic, having ALL of the 
following:
  (a) water bottles;
  (b) foam fan blades;
  (c) battery operated

VENTILATORS, IP44 compliant, having a noise level NOT less than 
65 dB (A) and NOT greater than 75 dB (A)

BLOWERS, ROTARY, positive displacement, having a flow rate NOT 
less than 100 cubic metres per hour

FANS, AXIAL, having an external AC rotor motor

VENTILATORS, HATCHERY LINE

BLOWERS, VACUUM CLEANER, having BOTH of the following:
   (a) bypass OR flow through discharge;
   (b) air flow NOT exceeding 70 litres per second

FANS, radial, negative air pressure, asynchronous OR external rotor
 motors, size ranges of 150 mm to 716 mm diameter and 120 mm to
 460 mm depth including motor protrusion, with dynamically and
 statically balanced impellers

FANS INCORPORATING BRUSHLESS MOTORS, having ANY of the following:
   (a) DC powered;
   (b) 230-277 V AC single phase supply, incorporating external
       electronic commutation converting AC into DC;
   (c) 400-415 V AC three phase supply, incorporating electronic
       commutation converting AC into DC

CONDENSING HOODS, with OR without installation kit, having ALL 
of the following:
  (a) two speed fan;
  (b) grease filter;
  (c) heat exchanger

CONDENSING HOODS, with OR without installation kit, having ALL 
of the following:
  (a) two speed fan;
  (b) three stage filtration;
  (c) heat exchanger

RANGEHOODS

SUPERCHARGERS, automotive, being original equipment or
 reproductions of original equipment fitted to vehicles
 manufactured prior to 1962

BARE UNITS (AIR ENDS), having a continuous working pressure of
 2 750 kPa or greater, but NOT including ANY of the following:
   (a) driving motors or motor starters;
   (b) separate aftercoolers, moisture separators, or base
       frames

BOOSTERS, vacuum, rotary lobe type, mechanical, positive
 displacement, having a capacity exceeding 100 cu m/h, oil free
 with bare shaft

TURBOCHARGERS

COMPRESSORS, air, operated solely by 6 V or 12 V DC power

COMPRESSOR/VACUUM PUMPS, diaphragm type, oil-less or oil free,
 having ALL of the following:
   (a) capacity NOT exceeding 15 L/min of free air;
   (b) ultimate vacuum between - 1.8 kPa and - 73.6 kPa, gauge

BARE UNITS (AIR ENDS), having ALL of the following:
   (a) two intermeshing rotors in helical configuration;
   (b) rated capacity exceeding 0.6 cu m/min of free air delivered
       at published maximum working pressure and at published
       maximum speed;
 but NOT including ANY of the following:
          (i) drivers;
         (ii) electric motor starters;
        (iii) after coolers;
         (iv) moisture separators;
          (v) ancillaries

AIR COMPRESSORS, linear motor driven, free piston, oil free
 operation, capable of EITHER of the following:
   (a) a maximum flow of 120 L/min at a maximum pressure of 0.5 bar;
   (b) a maximum flow of 16 L/min at a maximum pressure of 3 bar

BARE COMPRESSORS, having ALL of the following:
   (a) 1 or more cylinders;
   (b) capacity NOT exceeding 2 600 L/min;
   (c) maximum working pressure NOT exceeding 2000 kPa
 For the purposes of TC 9407805 a "bare compressor" is:
   (a) only that part providing the compressed air, which is to be
       incorporated into a compressor package; AND
   (b) does NOT include driving units, pressure receivers exceeding
       5 L capacity or base frames

COMPRESSORS, having BOTH of the following:
   (a) capacity NOT exceeding 150 L/min at 700 kPa;
   (b) noise rating NOT exceeding 70 dB at 1 m

COMPRESSORS, air brake system, reciprocating piston type having a
 displacement at 1 250 RPM exceeding 6 CFM but NOT exceeding 35 CFM

PULSE COMPRESSOR SYSTEM, skid mounted, including ALL of the 
following:
  (a) air compressor;
  (b) compressed air dryer;
  (c) compressed air filtration;
  (d) air receiver;
  (e) pulse control system;
  (f) electrical circuits

AIR SUPPLY SYSTEM, RAIL VEHICLE, including ALL of the following:
  (a) compressor set consisting of ALL of the following:
          (i) rotary screw compressor;
         (ii) three-phase motor; 
        (iii) air filter; 
         (iv) centrifugal fan AND/OR cooler, 
  (b) air dryer; 
  (c) exhaust cowl; 
  (d) oil filter;
  (e) silencer with mufflers;
  (f) electrical unit

NITROGEN BOOSTER COMPRESSORS, having an outlet pressure NOT 
greater than 3 860 kPa

AIR SUPPLY UNIT, MATTRESS

KITS, AIRBAG SUSPENSION CONTROL, consisting of ALL of the 
following:
  (a) electronic control unit;
  (b) handheld controller;
  (c) air compressor;
  (d) compressor relay;
  (e) air filter;
  (f) valve block;
  (g) height sensors;
  (h) mounting brackets AND fittings;
  (i) airline tubing;
  (j) wiring harness;
  (k) fasteners

AIR COMPRESSORS, SCREW OR PISTON OR RECIPROCATING, free air 
delivery NOT greater than 3 cubic metres per minute, having ALL 
of the following:
  (a) refrigeration dryer;
  (b) air receiver;
  (c) programme controller

AIR COMPRESSORS, free air delivery NOT exceeding 3 cubic metres 
per minute, being ANY of the following:
  (a) screw compressors;
  (b) piston compressors;
  (c) reciprocating compressors;
  (d) rotary screw compressors

PUMPS, rechargeable, 12 volt, cordless, multi-purpose

COMPRESSORS, AIR, volumetric rotary vane, having BOTH of the 
following:
  (a) operating pressure NOT greater than 700 kPa;
  (b) free air delivery capacity NOT greater than 3 cubic 
      metres per minute

COMPRESSORS, BREATHABLE AIR, RECIPROCATION PISTON, complying 
with Australian/New Zealand Standard AS/NZS 2299.1:1999 AND 
AS/NZS 1715:1994, having BOTH of the following:
  (a) continuous working pressure NOT less than 25 000 kPa;
  (b) compressed air delivery NOT less than 100 L per minute

PUMPS, AIR, having a voltage NOT less than 240 volts

COMPRESSORS, PNEUMATIC TOOL, direct drive, comprising BOTH of 
the following:
 (a) tank size NOT greater than 50 litres;
 (b) handle bars

COMPRESSORS, AIR, rotary, twin screw, having an operating 
pressure NOT greater than 700 kPa

COMPRESSORS, OILESS

BARE UNITS (AIR ENDS), having ALL of the following:
   (a) two intermeshing rotors in helical configuration;
   (b) rated capacity exceeding 0.6 cu m/min of free air delivered
       at published maximum working pressure and at published maximum
       speed;
 but NOT including ANY of the following:
      (i) drivers;
     (ii) electric motor starters;
    (iii) after coolers;
     (iv) moisture separators;
      (v) ancillaries

COMPRESSORS, air, reciprocating, oil free, capable of operating at a
 working pressure of 4000 kPa

BOOSTERS, mechanical, positive displacement, rotary lobe type,
 having a displacement (swept volume) of NOT less than 300 cu m/hr
 and NOT exceeding 1 500 cu m/hr

GAS BOOSTERS, centrifugal, multistage, oil free, skid mounted, 
having ALL of the following: 
  (a) 2 pole motor with heaters AND thermistors;
  (b) discharge gas pressure transmitters;
  (c) valves;
  (d) cut out switches;
  (e) accelerometers;
  (f) control panel; 
  (g) weather enclosure

COMPRESSORS, rotary sliding vane, positive displacement, air 
cooled, skid mounted, having ALL of the following: 
  (a) complying with The European Parliament and of the European
      Council Directive 1999/92/EC; 
  (b) oil lubricated; 
  (c) 4 pole motor with heaters AND thermistors;
  (d) weather enclosure;
  (e) condensate pot;
  (f) oil tank; 
  (g) splitter manifold

AIR COMPRESSORS, skid mounted, including ALL of the following:
  (a) diesel engine;
  (b) piston compressor;
  (c) relief valve;
  (d) cooler;
  (e) air receiver;
  (f) output capacity exceeding 3 cubic metres but NOT
      exceeding 25 cubic metres of free air delivered per minute

AIR COMPRESSORS, rotary tooth, reciprocating piston, having a 
free air delivery NOT less than 3 c/m3 per minute and NOT 
greater than 25 c/m3 per minute

AIR COMPRESSOR SYSTEM, programmable logic controlled, having 
ALL of the following:
  (a) rotary screw compressor;
  (b) integrated refrigeration dryer;
  (c) output capacity exceeding 3 cubic metres per minute
      but NOT exceeding 25 cubic metres per minute

AIR COMPRESSORS, rotary screw, single stage OR two stage, rated 
output capacity exceeding 3 cubic metres per minute but 
NOT exceeding 25 cubic metres per minute

AIR COMPRESSORS, VOLUMETRIC ROTARY VANE, having an operating 
pressure NOT less than 750 kPa

COMPRESSORS, 4-STAGE FORCE FEED LUBRICATION, having BOTH of the 
following:
  (a) working pressure NOT less than 90 bar and NOT
      greater than 330 bar;
  (b) maximum pressure of 350 bar

COMPRESSORS, AIR, rotary, twin screw, having an operating 
pressure NOT greater than 700 kPa

IMPELLER, compressor, gas

BLADES, domestic ceiling sweep fan

BLADES, compressor, rotary vane

PARTS, DIESEL ENGINE, being ANY of the following:
   (a) turbocharger:
          (i) diffuser;
         (ii) heat shield;
        (iii) housing;
         (iv) impeller;
          (v) wheel;
         (vi) wheel and shaft,
   (b) air compressor:
          (i) connection;
         (ii) housing;
        (iii) support

FAN CHASSIS, industrial, having a space for the cooling fans placed
 side by side

PARTS, RECIPROCATING OPEN DRIVE REFRIGERATION OR AIR CONDITIONING
 COMPRESSORS having a swept volume capacity exceeding 20 L/s, being
 ANY of the following:
   (a) piston conrods;
   (b) rod and piston bearings;
   (c) pistons;
   (d) cylinder sleeves;
   (e) valve plates;
   (f) cylinder heads;
   (g) manifolds;
   (h) drive plates;
   (i) sumps;
   (j) plate-heads;
   (k) support-heads;
   (l) reed-heads;
   (m) cage-heads;
   (n) sleeve-heads;
   (o) heads;
   (p) reed-pistons;
   (q) head-pistons;
   (r) compressor bodies;
   (s) overhaul kits comprising ALL of the following:
         (i) pistons;
        (ii) sleeves;
       (iii) seals;
        (iv) rod bearings;
         (v) piston bearings;
        (vi) valve plates;
       (vii) lubricating oil;
      (viii) gaskets

PARTS, AXIAL FLOW FANS BEING ANTI STALL AND VARIABLE PITCH WHILST
 IN MOTION AND HAVING A MINIMUM DIAMETER OF 800 mm OR GREATER BUT NOT
 EXCEEDING 3.96 m, being ANY of the following:
   (a) 3 dimensional blades;
   (b) impellers;
   (c) blade supports;
   (d) hubs;
   (e) blade shafts;
   (f) housings

PARTS, TUNNEL OR MINE VENTILATION FAN, being EITHER of the 
following:
  (a) impellers having ANY of the following:
          (i) blades;
         (ii) hubs;
        (iii) discs;
         (iv) cover plates;
          (v) washers,
  (b) casings having ANY of the following:
          (i) inlet cone;
         (ii) dome;
        (iii) protective mesh;
         (iv) hatch;
          (v) washers

PARTS, ADJUSTABLE PITCH FAN, being hub assembly

PARTS, TUNNEL VENTILATION FAN, being ANY of the following:
  (a) domes;
  (b) silencer heads;
  (c) inlet bells;
  (d) impellers, including ANY of the following:
          (i) blades;
         (ii) hub discs;
        (iii) boss;
         (iv) retaining discs;
          (v) locking washers;
         (vi) fixation hex bolts

PARTS, CENTRIFUGAL FAN, being EITHER of the following:
  (a) rotors;
  (b) casings

PARTS, AIR COMPRESSORS, OIL-FREE SCREW , being any of the 
following;
  (a) air end element;
  (b) aftercooler;
  (c) intercooler

ROTARY BLOCK, ROTARY COMPRESSOR, TRAIN AND/OR TRAM

PARTS, COMBUSTION AIR FAN, BLAST FURNACE, being ANY of the 
following:
  (a) impellors;
  (b) shafts;
  (c) impellor and shaft sets

PARTS, INDUSTRIAL FAN, being ANY of the following:
  (a) impellors;
  (b) shafts;
  (c) impellor and shaft sets

PARTS, COOLING TOWER FAN, being hubs

PARTS, TUNNEL VENTILATION FAN, being EITHER of the following:
  (a) impellers;
  (b) casings

BLADES, AXIAL FAN, COOLING TOWER, fibre reinforced polyester, 
having a diameter NOT less than 6 m and NOT greater than 11 m

PISTON RODS, COMPRESSOR

AIR CONDITIONERS, wall mounted, having ALL of the following:
  (a) rated cooling capacity NOT less than 14 900 watts
      at an ambient temperature of 55 degrees Celsius;
  (b) rated heating capacity NOT less 9 900 watts;
  (c) temperature limiter AND/OR indicator;
  (d) control unit AND/OR panel;
  (e) air supply inlet AND/OR fan;
  (f) supply air flow NOT less than 2 400 cubic metres per hour;
  (g) width NOT greater than 711 mm

CLIMATE CONTROL UNIT, ROOT VEGETABLE, with control panel

AIR CONDITIONERS, self-contained, wall mounted, reverse cycle, 
having ALL of the following:
  (a) cooling capacity greater than 12 000 watts; 
  (b) heating capacity NOT less than 6 800 watts;
  (c) temperature sensor;
  (d) control unit;
  (e) fresh air supply port

AIR CONDITIONER, direct expansion, air OR fluid-cooled, single 
OR multi-phase, with OR without refrigerant unit, having ALL of 
the following:
  (a) input voltage NOT greater than 480 V;
  (b) nominal net cooling capacity NOT less than 2 kW and NOT 
      greater than 42 kW;
  (c) variable speed fans;
  (d) factory-wired condensate pump

RESINOUS MATERIAL STORAGE AND CUTTING MACHINES, including BOTH 
of the following:
  (a) refrigerated storage chamber;
  (b) cutting discs

AIR CONDITIONERS, COMPUTER HEAT AND HUMIDITY PROTECTION, with OR 
without condenser, including BOTH of the following:
  (a) indoor unit, having an internal inverter compressor;
  (b) maximum gross total cooling capacity NOT greater than
      148 kW

AIR CONDITIONING FAN COIL UNITS, chilled water, cooling AND/OR 
heating, wall mounted, having ALL of the following:
  (a) plastic external casing with diffusion flap;
  (b) heat exchange coil;
  (c) AC OR EC motors;
  (d) fan assembly;
  (e) condensate pump;
  (f) air filter;
  (g) power supply NOT less than 230 volts 
  (h) minimum cooling capacity NOT less than 1 150 W and 
      maximum NOT greater than 3 850 W;
  (i) minimum airflow NOT less than 190 m3/h and maximum airflow 
      NOT greater than 790 m3/h

AIR CONDITIONER, non-ducted, reverse cycle, having ALL of the
following:
   (a) net rated cooling capacity of NOT less than 1 900 watts 
       and NOT greater than 9 000 watts;
   (b) moisture removal of 1.2 litres/hour OR greater;
   (c) airflow of 84 litres/second OR greater;
   (d) net rated heating capacity of NOT less than 1 970 watts
       and NOT greater than 9 500 watts

AIR CONDITIONERS, reverse cycle, having ALL of the following:
  (a) cooling capacity NOT less than 1 910 W and NOT
      greater than 2 900 W;
  (b) moisture removal NOT less than 0.7 litres/hour;
  (c) airflow NOT less than 84 litres/second;
  (d) heating capacity NOT less than 1 800 W

COOLING UNITS, CABINET OR WALL OR ROOF MOUNTED, having a cooling 
capacity NOT greater than 5 400 watts

COOLERS, having ALL of the following:
  (a) compliance with Ingress Protection 34 OR Ingress 
      Protection 54;
  (b) cooling capacity NOT less than 230 W and NOT greater than
      10 500 W;
  (c) noise level NOT greater than 80 dB (A)

AIR CONDITIONERS, DOMESTIC, having a heating and cooling 
capacity NOT greater than 1 000 watts

COOLERS, having ALL of the following:
  (a) compliance with IP34 OR IP54;
  (b) cooling capacity NOT less than 230 W and NOT greater than
      10 500 W;
  (c) noise level NOT less than 65 dB (A) and NOT greater than 
      77 dB (A)

AIR CONDITIONERS, DOMESTIC, reverse cycle, having ALL of the
 following:
   (a) cooling capacity NOT less than 1910 watts but NOT
       more than 2900 watts;
   (b) moisture removal 0.7 litres/hour OR greater;
   (c) airflow 84 litres/second OR greater;
   (d) heating capacity 1 970 watts OR greater

AIR CONDITIONER, SELF-CONTAINED, reverse cycle, having ALL of
 the following:
   (a) cooling capacity of 1 910 watts OR greater;
   (b) moisture removal of 1.0 litre/hour OR greater;
   (c) airflow of 84 litres/second OR greater;
   (d) heating capacity of 1 800 watts OR greater

AIR CONDITIONERS, DOMESTIC, cooling only

AIR CONDITIONERS, CARAVAN AND/OR MOTOR HOME LIVING AREA, remote 
AND/OR manually controlled, having BOTH of the following:
  (a) operational voltage NOT greater than 250 V AC;
  (b) heating AND/OR cooling controls, 
with OR without ANY of the following: 
           (i) lighting;
          (ii) remote controls, with OR without batteries;
         (iii) cold plasma air purifiers;
          (iv) nuts AND/OR bolts;
           (v) screws;
          (vi) brackets;
         (vii) tie down straps;
        (viii) air grilles;
          (ix) control cables;
           (x) electric connectors;
          (xi) air outlets;
         (x11) air filters

AIR CONDITIONERS, TRUCK CABIN, 12 AND/OR 24 V DC, cooling, 
remote controlled, having ALL of the following: 
  (a) compressor unit cooling capacity NOT less than 850 W; 
  (b) truck engine off operation;
  (c) self contained OR split system, 
with OR without installation kits consisting of NOT less than  
ANY two OR more of the following: 
     (i) frames; 
    (ii) bolts; 
   (iii) washers 
    (iv) nuts; 
     (v) brushes; 
    (vi) seals; 
   (vii) mountings; 
  (viii) trim panels; 
    (ix) fixtures; 
     (x) cables; 
    (xi) manuals AND instructions;
   (xii) covers

AIR CONDITIONERS, BUS AND/OR COACH, roof mounted, having ALL of 
the following:
  (a) cooling capacity NOT less then 10 kW;
  (b) heating capacity NOT less than 10 kW;
  (c) evaporator air capacity NOT less than 1 900 cubic metres 
      per hour

AIR CONDITIONERS, truck cabin, refrigerated, having ALL of the 
following:
  (a) compressor unit NOT less than 950 W;
  (b) evaporator unit NOT less than 7 000 btu;
  (c) remote control;
  (d) engine off operation

AIR CONDITIONERS, BUS, ROOF MOUNTED, having ALL of the following;
 (a) cooling capacity NOT less than 10 kW;
 (b) heating capacity NOT less than 10 kW;
 (c) belt driven compressors;
 (d) evaporator air capacity NOT less than 1 900 cubic metres
     per hour

AIR CONDITIONERS, DOMESTIC, reverse cycle, having ALL of the
 following:
   (a) cooling capacity NOT less than 1910 watts but NOT
       more than 2 900 watts;
   (b) moisture removal 0.7 litres/hour OR greater;
   (c) airflow 84 litres/second OR greater;
   (d) heating capacity 1 970 watts OR greater

DRY CONDITIONERS, lithium chloride desiccant solution, comprising
 ALL of the following:
   (a) dehumidifier;
   (b) cooler;
   (c) heater;
   (d) cooling capacity NOT less than 1 400 watts;
   (e) moisture removal NOT less than 2 litres per hour;
   (f) filter and purifier

AIR CONDITIONERS, MARINE, reverse cycle, having ALL of the 
following:
  (a) cooling capacity NOT less than 1.4kW;
  (b) supply voltage NOT less than 200 V;
  (c) sea water inlet

PUMPS, HEAT, comprising ALL of the following:
  (a) refrigerant compressors;
  (b) evaporator coils;
  (c) blowers;
  (d) co-axial heat exchangers

CONDITIONERS, AIR, gas AND/OR solar AND/OR diesel powered

AIRCONDITIONERS, reverse cycle, having NOT less than two wheels

DRY CONDITIONERS, lithium chloride desiccant solution, comprising
 ALL of the following:
   (a) dehumidifier;
   (b) cooler;
   (c) heater;
   (d) cooling capacity NOT less than 1 400 watts;
   (e) moisture removal NOT less than 2 litres per hour;
   (f) filter and purifier

AIR CONDITIONERS, DOMESTIC, reverse cycle, having ALL of the
 following:
   (a) cooling capacity NOT less than 1910 watts but NOT
       more than 2 900 watts;
   (b) moisture removal 0.7 litres/hour OR greater;
   (c) airflow 84 litres/second OR greater;
   (d) heating capacity 1 970 watts OR greater

AIR CONDITIONERS, DOMESTIC, reverse cycle, having ALL of the
 following:
   (a) cooling capacity 1910 watts OR greater;
   (b) moisture removal 1.2 litres/hour OR greater;
   (c) airflow 84 litres/second OR greater;
   (d) heating capacity 1970 watts OR greater

AIR CONDITIONING UNITS, COMPUTER SERVER ROOM, air OR water 
cooled, with OR without electrode steam humidifier, including 
ALL of the following:
  (a) radial fan having backward curved blades;
  (b) direct expansion refrigerant circuit;
  (c) evaporator coil;
  (d) filters;
  (e) controller, with OR without microprocessor;
  (f) scroll compressor;
  (g) sensors

AIR CONDITIONING UNIT, AIRCRAFT, on wheels, towable, diesel 
engine driven AND/OR wall powered

HEATING VENTILATING AND AIR CONDITIONING (HVAC) UNIT, DIESEL-
ELECTRIC LOCOMOTIVE, incorporating a refrigeration unit, 
including ALL of the following:
  (a) DC to AC inverter;
  (b) compressor;
  (c) evaporator blower AND motor;
  (d) condenser fan AND motor

COOLERS, including BOTH of the following:
  (a) indirect evaporative cooling with polymer tube heat  
      exchangers;
  (b) refrigerated cooling with digital scroll compressor,
with OR without one OR both of the following:
   (i) chilled water coil;
  (ii) dehumidification AND/OR humidification AND/OR outside air 
       pre-treatment unit

COOLING MACHINES, COMPUTER SERVER, DATA CENTRE, being air OR 
water cooled, having ALL of the following:
  (a) scroll compressor;
  (b) refrigerant circuit;
  (c) infrared humidifier

COOLING MACHINES, COMPUTER SERVER, DATA CENTRE, incorporating 
BOTH of the following:
 (a) refrigerant system;
 (b) digital scroll compressor

HEATING AND VENTILATION AND AIR CONDITIONING UNITS (HVAC), 
PASSENGER TRAIN, roof, mounted

AIR CONDITIONERS, PORTABLE

COOLERS, having ALL of the following:
  (a) compliance with Ingress Protection 34 OR Ingress 
      Protection 54;
  (b) cooling capacity NOT less than 230 W and NOT greater than
      10 500 W;
  (c) noise level NOT greater than 80 dB (A)

REFRIGERATED AIRCONDITIONERS, PORTABLE, cooling only

AIR CONDITIONERS, DOMESTIC, cooling only

CLIMATE CONTROL SYSTEM, GREENHOUSE, including ALL of the 
following:
  (a) fresh air unit;
  (b) top air system;
  (c) recirculation system;
  (d) fan coil unit

AIR HANDLING UNITS, PHARMACEUTICALS, including ALL of 
the following:
  (a) one OR more fans;
  (b) filters;
  (c) heating coil;
  (d) cooling coil;
  (e) humidifier;
  (f) evaporator

AIR CONDITIONING UNITS, COMPUTER SERVER ROOM, chilled water, 
including ALL of the following:
  (a) air filter;
  (b) fans, being EITHER of the following:
              (i) wheel fan;
             (ii) radial fan having backward curved blades,
  (c) chilled water circuit AND/OR coil;
  (d) controller, with OR without microprocessor;
  (e) sensors,
with OR without ANY of the following: 
            (i) electrode steam humidifier;
           (ii) control valve;
          (iii) two-way valve

HEATING AND COOLING MACHINES, POULTRY EGG HATCHERY, programmable 
logic controlled, including ALL of the following:
  (a) filters;
  (b) exhausts OR ventilators;
  (c) coolers;
  (d) humidifiers;
  (e) air handlers;
  (f) heat recoverers;
  (g) ducts

COOLING UNITS, having ALL of the following:
  (a) forward-curved OR backward-curved fan with directly 
      coupled asynchronous motor;
  (b) power supply NOT less than 230 volts and NOT greater than 
      400 volts;
  (c) gross total cooling capacity NOT less than 6.4 kW and NOT 
      greater than 107.6 kW;
  (d) airflow NOT less than 1 600 m3 per hour and NOT greater 
      than 21 810 m3 per hour

COOLING UNITS, CHILLED WATER, having BOTH of the following:
  (a) cooling capacity output NOT less than 20 kW  
      and NOT greater than 150 kW;
  (b) input voltage NOT less than 100 volts and NOT 
      greater than 460 volts

CLIMATE CONTROL, ANIMAL HUSBANDRY, comprising ALL of the 
following:
 (a) fans;
 (b) cool pads and/or cooling pumps;
 (c) vents;
 (d) winches;
 (e) sensors

PARTS, AIR CONDITIONER, being ANY of the following:
   (a) accumulators;
   (b) air deflectors;
   (c) air outlets;
   (d) bell mouths;
   (e) blades;
   (f) bleeders;
   (g) cabinets;
   (h) caps;
   (i) cassettes;
   (j) changeover boxes;
   (k) clips;
   (l) coils;
   (m) condensers;
   (n) connection plates;
   (o) connectors;
   (p) cover flaps;
   (q) covers;
   (r) dampers;
   (s) deflector supports;
   (t) deflectors;
   (u) discharge grills;
   (v) distributors;
   (w) drain caps;
   (x) drain connections;
   (y) drain dischargers;
   (z) drain pans;
  (aa) drainage trays;
  (ab) evaporators;
  (ac) exchangers;
  (ad) fan casings;
  (ae) fan covers;
  (af) fan motor supports;
  (ag) fan runners;
  (ah) fan support assemblies;
  (ai) fascias AND/OR panel edges;
  (aj) front covers AND/OR front panels;
  (ak) unions;
  (al) glands;
  (am) grills;
  (an) guards;
  (ao) guides;
  (ap) handles;
  (aq) headers;
  (ar) heat sinks;
  (as) holders;
  (at) hoses;
  (au) impellers;
  (av) indication boxes;
  (aw) inlet cones;
  (ax) inlet rings;
  (ay) knobs;
  (az) latches;
  (ba) led covers;
  (bb) lens covers;
  (bc) liquid buffers;
  (bd) looms;
  (be) mounting plates;
  (bf) mounts;
  (bg) mufflers;
  (bh) noise filters;
  (bi) pads;
  (bj) panels;
  (bk) pipe covers;
  (bl) piping assemblies;
  (bm) plates;
  (bn) plugs;
  (bo) ports;
  (bp) pulleys;
  (bq) reducers;
  (br) runners;
  (bs) saddles;
  (bt) separator blades;
  (bu) spacer sleeves;
  (bv) spigots;
  (bw) standoffs;
  (bx) stepping motors;
  (by) strainers;
  (bz) supports;
  (ca) insulation;
  (cb) wire holes AND/OR trunking

OUTDOOR CONDENSING UNIT, having ALL of the following:
  (a) input voltage NOT greater than 415 V AC three phase;
  (b) variable frequency drive;
  (c) network frequency NOT greater than 60 Hz;
  (d) variable speed compressor;
  (e) single OR dual power feed

PARTS, AIR CONDITIONER INDOOR SPLIT SYSTEM UNIT, being airflow 
outlet cassette assemblies including ALL of the following:
  (a) plastic panel with return air intake AND directional
      air flow outlets;
  (b) motorised swing louvres;
  (c) detachable washable filters;
  (d) infrared receiver;
  (e) infrared transmitter

AIR CONDITIONERS, INDOOR UNITS, reverse cycle, split system, 
inverter OR variable refrigerant flow, having BOTH of the 
following:
  (a) cooling capacity NOT less than 1.5 kW and NOT greater than
      2.2 kW;
  (b) heating capacity NOT less than 2.5 kW and NOT greater than
      3.3 kW

TANKS, REFRIGERANT STORAGE, AIR CONDITIONING SYSTEM

INDOOR UNITS, SPLIT SYSTEM AIR CONDITIONER, reverse cycle, 
inverter or variable refrigerant flow, having BOTH of the 
following:
  (a) rated cooling capacity NOT less than 2.2 kW;
  (b) rated heating capacity NOT less than 2.5 kW

CONDENSERS, AIR CONDITIONING, outside building, comprising ALL 
of the following:
  (a) scroll compressors;
  (b) condensing coils;
  (c) axial fans;
  (d) capacity NOT less than 100 kW

PARTS, AIR CONDITIONER, INDOOR, split system, reverse cycle, 
wall AND/OR ceiling mounted, comprising all of the following:
  (a) coils;
  (b) fans;
  (c) louvers;
  (d) refrigerant expansion regulators

PARTS, AIRCONDITIONER, split system, reverse cycle, being 
condensers

PARTS, AIR CONDITIONER, CONDENSER, split system, reverse cycle, 
having ALL of the following:
  (a) rated cooling capacity NOT less than 5.30 kW;
  (b) rated heating capacity NOT less than 5.60 kW;
  (c) digital inverter compressors

PARTS, AIR CONDITIONER, CONDENSER, split system, reverse cycle, 
having ALL of the following:
  (a) rated cooling capacity NOT less than 8.50 kW;
  (b) rated heating capacity NOT less than 8.70 kW;
  (c) outdoor airflow NOT less than 1 000 litres per second;
  (d) scroll compressors

PARTS, AIR CONDITIONER, CONDENSER, split system, multi head, 
reverse cycle, having BOTH of the following:
  (a) cooling capacity NOT less than 1.10 kW;
  (b) heating capacity NOT less than 0.70 kW

INDOOR UNITS, SPLIT SYSTEM AIR CONDITIONER, domestic, containing
 NO heating OR cooling OR humidifying OR de-humidifying devices,
 but comprising ALL of the following:
   (a) fan and/or air blower;
   (b) motorised swing levers;
   (c) copper coil;
   (d) infra-red sensor controls;
   (e) control panel

BURNERS, forced draft, using EITHER gas OR a combination of
 gas and oil

BURNERS, OXYGEN/GAS, having a heating capacity of 100,000 Btu OR
 greater when using natural gas at 1 000 Btu/scf

FURNACE GAS BURNERS, STEEL STRIP METAL COATING LINE, including 
ANY of the following;
  (a)burner panels with OR without ANY of the following:
          (i) insulation;
         (ii) plates;
        (iii) gaskets,
  (b)burner blocks with cartridges

GAS FURNACE BURNER PANELS, STEEL STRIP METAL COATING LINE, 
including ANY of the following;
  (a) insulation;
  (b) plates;
  (c) gaskets

GAS BURNERS, WALKING BEAM FURNACE, with OR without ANY of the 
following:
  (a) burner block OR burner tip OR air baffle; 
  (b) valve, with OR without actuator;
  (c) seal kit

MODULATING BURNERS, BOILER, natural gas and/or biogas, including 
ALL of the following:
  (a) wind box; 
  (b) sight glass; 
  (c) air damper servomotor; 
  (d) natural gas lances;
  (e) biogas ring; 
  (f) nozzles AND control valves;
  (g) cooling air system;
  (h) pilot burner;
  (i) transformer AND ignition electrodes; 
  (j) flame scanner; 
  (k) control panel; 
  (l) gas hose AND/OR compensator; 
  (m) gas control valve servomotor;  
  (n) gas shut-off valve unit;
  (o) pressure switches;
  (p) burner management system

REACTOR BURNERS, ACID REGENERATION PLANT, butane OR propane, 
having BOTH of the following:
  (a) 3 burners with an operating range NOT less than 100 kW and 
      NOT greater than 1 500 kW;
  (b) operating pressure NOT less than 50 mbar and NOT greater 
      than 130 mbar,
with OR without ANY of the following: 
            (i) combustion air stations; 
           (ii) regulation stations; 
          (iii) combustion fan;
           (iv) gas transport fan

REGENERATIVE BURNERS, BIOGAS, including ALL of the following:
  (a) burners;
  (b) gas supply valve trains;
  (c) burner control units;
  (d) exhaust valves

GAS BURNERS, WALKING BEAM FURNACE, with OR without burner blocks 
AND/OR seals

FURNACE BURNERS, GAS OR OIL AND/OR WOOD DUST, including ALL of 
the following:
  (a) combustion chambers, including BOTH of the following:
         (i) air regulator flaps;
        (ii) actuators,
  (b) burner muffles, including BOTH of the following:
         (i) air regulator flaps;
        (ii) cooling fans, having motors, 
  (c) gas conduits;
  (d) dust dosers

BURNERS, BOILER, multiple stage

BURNERS, LOW NITROGEN OXIDE, PULVERISED COAL

TRAVELLING GRATES, BOILER BIOMASS FUEL STOKING, having planetary 
gear drives

NOZZLES, oil burner, pressure atomizing type (including nozzles
 incorporating a strainer or a filter), capacity 0.43 mL or
 greater/s but NOT exceeding 105 mL/s at 690 kPa

PARTS, CALCINER BURNER LANCES, being ANY of the following:
  (a) lances with connectors;
  (b) tips;
  (c) tubes;
  (d) injectors;
  (e) nozzles;
  (f) guides;
  (g) supports;
  (h) couplings

PARTS, BURNERS, GAS, FORCED DRAFT, being ANY of the 
following:
  (a) air boxes;
  (b) blast tubes;
  (c) burner heads;
  (d) electrodes;
  (e) fan impellors;
  (f) fan inlet eyes;
  (g) fan cases;
  (h) flame baffles;
  (i) gas bars;
  (j) igniter plates;
  (k) inlet dampers

IGNITION BURNERS AND/OR SPARK PLUGS, TUNDISH PRE-HEAT BURNER

CONTROLLED ATMOSPHERE BRAZING FURNACES, including ALL of the 
following:
  (a) preheater;
  (b) atmospheric cleansing AND/OR purification chamber;
  (c) furnace

ROTARY HEARTH FURNACE, STEEL BALL, unassembled, programmable 
logic controlled, including ALL of the following:
  (a) charging chute;
  (b) discharging machine;
  (c) heating unit;
  (d) burners;
  (e) steel plates;
  (f) refractory lining;
  (g) air blowers;
  (h) ducting;
  (i) instrumentation

OVENS, rotary, combustion, having ALL of the following features:
   (a) fitted with a programmable controller capable of storing a
       minimum of 40 programs;
   (b) variable speed fan;
   (c) automatic vapour discharge valve control;
   (d) integral steam generation system;
   (e) a minimum of 15 tray capacity, tray size up to 460 x 760 mm;

OVENS, WAFER SHEETS, programmable logic controlled, including 
ANY of the following:
  (a) baking plates;     
  (b) fans AND/OR blowers;
  (c) conveyors;
  (d) waste bagging station; 
  (e) flame detector;
  (f) sheet checking system;
  (g) moisture analyser;  
  (h) elevator, wafer sheet AND/OR block; 
  (i) piping;
  (j) valves

OVENS, BAKERY, GAS, with OR without integrated loading system 
AND/OR gas fired burner, including BOTH of the following:
   (a) NOT less than 30 baking programs;
   (b) steam damper controllers

OVENS, BAKERY, multiple deck, programmable logic controlled, 
with thermo-oil boiler AND integrated loading device

OVENS, BAKERY, oil fuel AND/OR gas, rotary rack

OVENS, BAKERY, GAS, with OR without integrated hooking system 
AND/OR trolley, including ALL of the following:
  (a) steam generator;
  (b) stainless steel construction;
  (c) capacity NOT greater than 32 trays;
  (d) tray size NOT greater than 600 mm x 900 mm

OVENS, WAFER BAKING, with OR without EITHER of the following:
  (a) cleated elevator;
  (b) exhaust stack OR pipes

OVENS, PIZZA, gas, with OR without conveyors, having BOTH of the 
following:
  (a) NOT greater than 3 baking zones;
  (b) cooking capacity NOT greater than 7 200 pieces p/h

OVENS, BAKERY, gas operated, programmable logic controlled, 
including ALL of the following:
  (a) baking program controls;
  (b) steam damper controllers;
  (c) integrated loader AND unloader;
  (d) baking tunnel;
  (e) control panel

OVENS, BAKERY, GAS, multiple deck, programmable logic 
controlled, having ALL of the following:
  (a) NOT less than 30 baking programs;
  (b) steam damper controllers;
  (c) integrated loading system

BAKERY OVEN, ICE CREAM CONE, with interchangeable baking
 moulds, gas heated

LEHRS, GLASS BOTTLE ANNEALING AND/OR DRYING

THERMO BONDING MACHINES, including ALL of the following:
  (a) thermo-bonding oven, including ALL of the following:
          (i) NOT less than 5 gas burners;
         (ii) NOT less than 5 centrifugal fans;
        (iii) AC motor AND inverter;
         (iv) control panel,
  (b) cylinders;
  (c) cooling section, including AC motor AND inverter

GLASS MELTING FURNACE, OXYFUEL, programmable logic 
controlled, melting output NOT greater than 475 tonnes per day, 
including ALL of the following:
  (a) burners;
  (b) cooling distributor AND forehearth;
  (c) cooling supply system;
  (d) batch chargers with bin activators;
  (e) nozzles;
  (f) piping;
  (g) gas AND oxygen flow control;
  (h) peephole AND doghouse covers;
  (i) electrodes AND electrode holders;
  (j) control cabinets

GLASS MELTING FURNACE, OXYFUEL, programmable logic controlled, 
melting output NOT greater than 400 tonnes per day,  
including ALL of the following:
  (a) burners;
  (b) cooling distributor AND forehearth;
  (c) cooling supply system;
  (d) batch chargers;
  (e) nozzles;
  (f) piping;
  (g) exhaust;
  (h) gas AND oxygen flow control;
  (i) peephole AND doghouse covers;
  (j) sleeves;
  (k) electrode holders;
  (l) thermocouples AND holders;
  (m) control cabinets;
  (n) cooling water pump with tank;
  (o) forehearth lifting system

INTERNAL CURING OVENS, BEVERAGE CAN, having ALL of the following:
  (a) processing AND/OR production rate NOT less than 1 600 cans
      per minute;
  (b) operating temperature NOT exceeding 220 degrees C;
  (c) glass fibre open mesh conveyor belt; 
  (d) gas heated

PIN OVENS, BEVERAGE CAN, having ALL of the following:
  (a) process AND/OR production rate NOT less than 1 600 cans
      per minute;
  (b) operating temperature NOT exceeding 210 degrees C; 
  (c) roller chain conveyor; 
  (d) gas heated
with OR without pin stripper AND/OR platform

LEHRS, GLASS CONTAINER ANNEALING AND/OR DRYING

INCINERATORS, having BOTH of the following:
  (a) total air volume NOT greater than 14 100 nm3/h;
  (b) maximum caloric reaction temperature NOT less than 
      765 degrees Celsius

PYROLYSIS WASTE PROCESSING PLANT, with OR without control panel, 
including ALL of the following:
  (a) retort oven;
  (b) coolers;
  (c) liquid AND gas separator;
  (d) retort cylinder;
  (e) gauges;
  (f) storage tank;
  (g) walkway platform;
  (h) pipes;
  (i) pump;
  (j) oven rack;
  (k) thermocouples;
  (l) glass tube gas OR fluid scale

BURNERS AND/OR FLARES, GAS EMISSION, SEWAGE AND/OR BIOGAS PLANT, 
having ALL of the following:
  (a) flame arrestor;
  (b) slam shut valve;
  (c) burner control with ultra violet detector;
  (d) combustion chamber temperature monitor

KILNS, GLASS LAMINATION, gas powered, with OR without racking

LEHRS, GLASS BOTTLE ANNEALING AND/OR DRYING

TUYERES

PARTS, HARDENING FURNACE, being rolls

PARTS, EXHAUST GAS STACK, GLASS MELTING FURNACE, 
being ANY of the following:
  (a) air inlet;
  (b) cleaning nozzle;
  (c) thermo element;
  (d) quench air system with air injector system, including ALL 
      of the following:
          (i) nozzles;
         (ii) flanges, AND fittings, AND tubes;
        (iii) fans;
         (iv) control unit,   
  (e) furnace pressure regulating barrier air system, including 
      ALL of the following:
          (i) nozzles;
         (ii) flanges, AND fittings, AND tubes;
        (iii) fans;
         (iv) control unit,
  (f) fumes monitoring probe points;
  (g) stack

GRIZZLIES, LIME KILN

GALVANISING KETTLES, having ALL of the following:
  (a) wall thickness NOT less than 50 mm and NOT greater than 
      65 mm;
  (b) electro slag welded;
  (c) carbon content NOT greater than 0.08%;
  (d) silicon content NOT greater than 0.03%

PARTS, ETHYLENE STEAM CRACKING FURNACE, being inlet clean-out 
assemblies, whether OR not assembled, consisting of ALL of the 
following: 
  (a) tee fittings;
  (b) flanges;
  (c) flanged plug AND/OR end plug

PARTS, BLAST FURNACE, being feeder chutes OR spouts

PARTS, WAFER BAKING OVEN, being ANY of the following:
  (a) baking plates;
  (b) baking plate carriers OR frames;
  (c) carrier assemblies, whether OR not assembled, including 
      BOTH of the following:
          (i) baking plate;
         (ii) carrier OR frame

PARTS, ETHYLENE STEAM CRACKING FURNACE, being ANY of the 
following:
  (a) inlet AND/OR outlet reducers;
  (b) slip tubes;
  (c) stepped elbows AND/OR bends;
  (d) Y shaped tube unit

PARTS, ETHYLENE STEAM CRACKING FURNACE, being tube assemblies,  
including at least ANY two of the following:
  (a) bent tubes; 
  (b) elbow tubes; 
  (c) straight tubes;
  (d) Y shaped tubes,
with OR without ANY of the following:
           (i) flanges;
          (ii) nozzles;
         (iii) temperature sensor guard holders;
          (iv) tube holders

PARTS, BLAST FURNACE, being static distributors

PARTS, ETHYLENE STEAM CRACKING FURNACE, being ANY of the 
following:
  (a) outlet elbow;
  (b) quench manifolds;
  (c) radiant coils AND/OR radiant elements;
  (d) convection tubes;
  (e) radiant tubes

PARTS, GAS STACK, being EITHER of the following:
  (a) flare tips;
  (b) flare igniters

PARTS, BLAST FURNACE TUYERE, being inserts OR laval nozzles

PARTS, MATERIAL GATE, BLAST FURNACE, being protection plates

PARTS, FLASH FURNACE, with supporting framework, being remotely 
cooled copper cast around monel OR copper tubing elements

PARTS, HARDENING FURNACE, being rolls

ELEMENTS, BLAST FURNACE, water cooled, copper

WEAR PLATES, BLAST FURNACE

REFRIGERATORS, absorption, front-opening door type, gross
 internal capacity exceeding 170 L, being EITHER of the
 following:
   (a) combination gas/electric operation;
   (b) kerosene operation

COMBINED REFRIGERATORS AND FREEZERS, whether OR not integrated, 
incorporating separate external doors, having an internal 
capacity NOT greater than 900 litres

REFRIGERATOR-FREEZERS, COMBINED, absorption, gas operated

REFRIGERATOR-FREEZERS, COMBINED, fitted with separate external 
doors, having a gross internal volume NOT greater than 200 
litres

REFRIGERATORS, compression, 12 OR 24 volt DC powered

REFRIGERATORS, compression, capacity NOT exceeding 150 L, having ALL
 of the following:
   (a) combined or separate freezer compartment;
   (b) 240 V AC and 12/24 V DC operation;
   (c) with or without outer casing

REFRIGERATORS, compression, cabinet type, freestanding OR 
integrated, having an internal capacity NOT greater than 600 
litres

REFRIGERATORS, underbench OR integrated, having an internal 
capacity NOT greater than 400 litres

REFRIGERATORS, having BOTH of the following:
  (a) capacity NOT greater than 175 litres; 
  (b) height NOT greater than 890 mm

REFRIGERATORS, having BOTH of the following:
  (a) capacity NOT greater than 175 litres; 
  (b) height NOT greater than 870 mm

REFRIGERATORS, having BOTH of the following:
(a) a capacity NOT greater than 175 Litres; and
(b) an overall height NOT greater than 860mm

REFRIGERATORS, compression, capacity NOT exceeding 150 L, having ALL
 of the following:
   (a) combined or separate freezer compartment;
   (b) 240 V AC and 12/24 V DC operation;
   (c) with or without outer casing

REFRIGERATORS, absorption, front-opening door type, gross internal
 capacity NOT less than 95 L, capable of operation on ALL of the
 following power sources:
   (a) gas;
   (b) mains electricity;
   (c) 12 V DC

REFRIGERATORS, absorption, capacity NOT exceeding 120 L having
 the following:
   (a) combination gas/electric operation;
   (b) front opening only;
   (c) interchangeable hinges to allow for left OR right opening;
   (d) with OR without a finished outer cabinet
 whether OR not combined with a freezer compartment

COOLERS, WINE, thermoelectric, capacity NOT greater than 140 
litres

FREEZERS, laboratory, having an operating temperature of less
 than - 40 degrees C

FREEZERS, chest-type, including ALL of the following:
  (a) lockable steel OR glass lids;
  (b) freezing temperature NOT less than minus 30 degrees and
      NOT greater than minus 10 degrees Celsius;
  (c) digital temperature display;
  (d) integrated lock AND keys;
  (e) capacity NOT less than 170 L

FREEZERS, having BOTH of the following:
  (a) freezing temperature NOT greater than minus 60 degrees C;
  (b) capacity NOT less than 300L

FREEZERS, laboratory, having an operating temperature of less
 than - 40 degrees C

BIOMEDICAL FREEZERS, upright, including BOTH of the following:
  (a) temperature range NOT less than -30 degrees Celsius and 
      NOT greater than -20 degrees Celsius;
  (b) capacity NOT less than 600 litres

FREEZERS, upright, having a capacity NOT greater than 600 litres

FREEZERS, upright, having a capacity NOT greater than 400 litres

FREEZERS, vertical, capacity NOT exceeding 200 L

FREEZERS, BLOOD PLASMA

REFRIGERATED DISPLAY CABINETS, open front, with OR without night 
blind

FREEZERS, vertical, having ALL of the following:
  (a) operating temperature NOT less than minus 22 degrees
      Celsius and NOT greater than 8 degrees Celsius;
  (b) glass doors;
  (c) volume capacity NOT less than 1 600 L

REFRIGERATED CABINETS, wheeled, having air curtains

CARTS, VENDING, refrigerated, electric, including ALL of the 
following:
  (a) hermetic condensing unit;
  (b) two fixed wheels AND one pivoting wheel;
  (c) canopy

DISPLAY CABINETS, REFRIGERATED FOODSTUFF AND/OR BEVERAGE, having 
ALL of the following:
  (a) operating temperature NOT less than minus 3 degrees 
      Celsius and NOT greater than 10 degrees Celsius;
  (b) volume capacity greater than 300 L;
  (c) adjustable shelving;
  (d) NOT less than two shelves;
  (e) cabinet length NOT less than 110 cm and NOT greater
      than 400 cm,
with OR without cabinet blinds

CHILLERS, RETAIL DISPLAY, including ALL of the following:
  (a) operating temperature NOT less than minus 22 degrees 
      Celsius and NOT greater than 8 degrees Celsius;
  (b) product display glass doors;
  (c) volume capacity greater than 250 L

CABINETS, REFRIGERATION, having ALL of the following:
  (a) temperature range NOT less than -30 degrees Celsius and 
      NOT greater than +43 degrees Celsius;
  (b) humidity control working capacity NOT less than 50% and 
      NOT greater than 95%;
  (c) hot gas defrosting;
with OR without air sanitizer

FREEZER CABINETS, VERTICALLY MOUNTED OVERHANGING, having ALL of 
the following:
  (a) temperature controller;
  (b) internal shelves incorporating sign holders;
  (c) interior light-emitting diode (LED) lighting;
  (d) support stand;
  (e) capacity NOT exceeding 900 L, 
with OR without EITHER of the following:
         (i) compartment cover plates;
        (ii) compartment dividers

CHILLERS, upright, including ALL of the following:
  (a) temperature display;
  (b) glass doors;
  (c) internal fluorescent OR LED lighting;
  (d) adjustable shelving;  
  (e) capacity NOT greater than 1 400 L;
  (f) adjustable temperature control NOT less than 1 degrees
      Celsius and NOT greater than 11 degrees Celsius

REFRIGERATORS, FOOD COOLING AND DRYING, having ALL of the 
following:
  (a) air disinfector AND activated carbon air filter;
  (b) temperature control working capacity NOT less than
      0 degrees Celsius and NOT greater than +25 degrees Celsius;
  (c) humidity control working capacity NOT less than 60% and NOT
      greater than 90%

CABINETS, REFRIGERATION, including ALL of the following:
  (a) stainless steel frame;
  (b) stainless steel AND glass doors with OR without locks;
  (c) adjustable temperature;
  (d) capacity NOT exceeding 210 L;
  (e) weight NOT exceeding 60 kgs

CHEST FREEZERS, DISPLAY, having a sliding lid, with OR without 
removable dividers

CABINETS, REFRIGERATION, commercial, having a capacity NOT 
greater than 170 litres

CABINETS, WINE, temperature controlled

REFRIGERATED DISPLAY ICE CREAM CABINETS, plc

FREEZERS, DISPLAY, CHEST, having removable baskets and sliding 
lid

REFRIGERATOR AND/OR FREEZER, PORTABLE, comprising ALL of the 
following:
  (a) insulation;
  (b) 12 volt DC AND/OR AC;
  (c) carry handles; 
  (d) volume NOT greater than 115 litres

HEAT PUMPS, AIR TO WATER, COOLING AND/OR HEATING, having BOTH of 
the following:
  (a) inverter unit;
  (b) maximum flow temperature NOT less than 75 degrees Celsius

WATER SOURCE HEAT PUMPS, including ALL of the following:
  (a) heating capacity NOT less than 200 kW and NOT greater than 
      2 500 kW;
  (b) twin-rotor screw compressors with variable capacity valve;
  (c) flooded heat exchangers;
  (d) touch screen

HEAT PUMPS, AIR TO WATER, COOLING AND/OR HEATING, with OR 
without hydronic modules, having ALL of the following:
  (a) nominal cooling capacity NOT less than 12 kW and NOT 
      greater than 530 kW;
  (b) nominal operating voltage NOT less than 350 Volts and NOT 
      greater than 450 Volts with 3 phase power;
  (c) centrifugal and/or axial fans

HEAT PUMPS, carbon dioxide refrigerant, having a heat capacity 
NOT greater than 4.5 kW

FREEZERS, single batch, hard serve ice-cream and confectionery,
 capacity NOT exceeding 10 L/h

COOLING MODULES, peltier, solid state thermoelectric, being
 thermocouples constructed of N and P elements capable of
 creating a temperature difference between a hot plate and cold
 plate of up to 100 degrees C by passage of an electric current

DEHUMIDIFIERS, domestic, compressor capacity NOT greater than
 1 000 W

WHIPPING AND DISPENSING MACHINES, fresh cream, but NOT
 including multi-function machines which have the facility
 to dispense products OTHER THAN fresh cream

REFRIGERATORS, cryogenic, using liquid nitrogen as the
 refrigerant, capable of achieving a storage temperature of
 - 125 degrees C or lower

FREEZERS, spiral belt, modular, having ALL of the following:
   (a) self stacking spiral belt system capable of forming self-
       contained freezing zone with each tier resting on vertical
       side links of the tier below it;
   (b) having an open mesh conveyor;
   (c) endlessly variable belt speed to allow selection of freezing
       time for different products

DISPENSERS, DRINK, refrigerated, counter top, continuous mixing

ICE CREAM MAKING MACHINES, continuous, capable of ALL of the
 following:
   (a) mixing and whipping of ingredients;
   (b) freezing ice cream mix;
   (c) direct extrusion of frozen product or connection to further
       processing machines

FREEZERS, ice cream, continuous, capable of ALL of the following:
   (a) mixing/whipping of ingredients;
   (b) direct extrusion of frozen product or connection to further
       processing machines;
   (c) one of the following output capacity ratings:
         (i) 75 to 150 L/h;
        (ii) 150 to 300 L/h;
       (iii) 225 to 450 L/h;
        (iv) 375 to 750 L/h

DISPENSERS, FROZEN CARBONATED BEVERAGE

SNOW ROOMS, pre-fabricated, assembled OR unassembled, including
ALL of the following:
  (a) wall panels;
  (b) steel AND copper pipes;
  (c) air conditioner AND snowmaker system;
  (d) compressor;
  (e) control system; 
  (f) lighting

CONDENSERS, REFRIGERATION, air or water-cooled, including ANY of 
the following:
  (a) frequency inverter;
  (b) fans;
  (c) control unit;
  (d) filter-dryer;
  (e) cartridge pressure switches AND transmitters;
  (f) oil heater with oil charge;
  (g) temperature sensors;
  (h) piping AND wiring,
with OR without ANY of the following:
          (i) refrigerant injection unit;
         (ii) oil separator with check valve;
        (iii) check valve in liquid line;
         (iv) cold room temperature sensor

PRE-CHILLERS, DRINK DISPENSER, including ALL of the following:
  (a) refrigeration compressor;
  (b) condenser;
  (c) water coils;
  (d) mechanical OR electronic thermostat

DISPENSERS, drink, having ALL of the following:
  (a) refrigerated ice making machine;
  (b) touch screen;
  (c) NOT less than 6 flavour bins;
  (d) flavour mixer;
  (e) dispensing one OR more drinks simultaneously

FREEZE THAW UNIT, having ALL of the following:
  (a) full load capacity NOT greater than 400 L;
  (b) temperature range NOT less than -90 deg and NOT greater 
      than 40 deg;
  (c) width NOT greater than 3 400 mm; 
  (d) depth NOT greater than 1 500 mm;
  (e) height NOT greater than 2 700 mm;
  (f) tray capacity NOT greater than 24 trays;
  (g) input power NOT greater than 400 V

REFRIGERATION UNITS, TRANSPORT, heating AND/OR cooling, AC/DC 
power supply, including ALL of the following:
  (a) condensers;
  (b) evaporators;
  (c) electronic controllers; 
  (d) cooling output NOT less than 2 700 Btu and NOT 
      greater than 4 700 Btu;
  (e) operating voltage NOT less than 11 V and NOT greater than 
15 V,
with OR without ANY of the following:
         (i) hot gas;
        (ii) door switch kit;
       (iii) hose AND/OR harness covers;
        (iv) vehicle mounting kit;
         (v) remote tracking AND monitoring; 
        (vi) plug socket

FREEZERS, spiral belt, with OR without one OR both of the 
following:
  (a) electrical control panel;
  (b) cleaning-in-place system

FREEZERS, spiral, programmable logic controlled, including ALL 
of the following:
  (a) stainless steel conveyor belt;
  (b) main drive unit;
  (c) control panel;
  (d) stainless steel floor;
  (e) air coolers;
  (f) sequential defrost,
with OR without ANY of the following:
          (i) conveyor belt cleaning system;
         (ii) air cooler cleaning AND rinsing module;
        (iii) conveyor belt oiling module

CHILLERS, air cooled, having ALL of the following:
  (a) hermetic scroll compressors;
  (b) direct expansion plate to plate evaporator;
  (c) condenser with coil fans;
  (d) refrigerant circuit; 
  (e) cooling capacity NOT less than 80 kW and NOT greater than 
      220 kW

FREEZER, spiral, programmable logic controlled, including ALL of 
the following:
  (a) stainless steel conveyor belt;
  (b) main drive unit;
  (c) control panel;
  (d) stainless steel floor;
  (e) NOT less than four air coolers;
  (f) sequential hot gas defrost, 
with OR without ANY of the following
          (i) belt cleaning system; 
         (ii) air cooler rinsing device;
        (iii) belt lubricator module

SPIRAL FREEZER, DOUGH, programmable logic controlled, including 
ALL of the following:
  (a) straight element;
  (b) drive unit;
  (c) electrical connections;
  (d) lubricator;
  (e) transfer unit;
  (f) supporting structure;
  (g) control panel;
  (h) belt;
  (i) freezing evaporator

CHILLERS, with OR without an acoustic enclosure, including ALL 
of the following:
  (a) R717 grade ammonia refrigerant gas;
  (b) secondary refrigerant outlet temperature NOT less than 
      -15 Celsius and NOT greater than +18 Celsius;
  (c) screw OR piston compressor;
  (d) power panel with frequency inverter;
  (e) fully welded plate heat exchanger condenser;
  (f) cooling capacity NOT less than 280 kW and NOT greater
      than 1 800 kW;
  (g) energy efficient ratio NOT less than 4.3

TUNNEL FREEZERS, FOOD PRODUCTION LINE, programmable logic 
controlled, having ALL of the following:
  (a) cryogen control system including motors;
  (b) length NOT greater than 20 m;
  (c) width NOT greater than 5 m;
  (d) height NOT greater than 5 m

SPIRAL FREEZERS, twin drum, programmable logic controlled,  
including ALL of the following: 
  (a) spiral conveyor modules;
  (b) evaporator coils;
  (c) dehumidifying units;
  (d) internal lighting;
  (e) integral platforms AND stairways;
  (f) housing

SAMPLE TUBE STORAGE UNIT, LABORATORY, refrigerated, whether OR 
not assembled, including ALL of the following:
  (a) storage racks;
  (b) racking robot

REFRIGERATION UNITS, MOTOR VEHICLE OR TRAILER, single AND/OR 
multi-compartment

COOLING MACHINES, TELECOMMUNICATION STATION, indoor OR outdoor, 
having microprocessor controllers

COOLING MACHINES, COMPUTER SERVER ROOM, having screw compressors 
AND/OR scroll compressors

ICE MAKING MACHINES, having ALL of the following:
  (a) cube production NOT greater than 1 500 kg per 24 hours;
  (b) power input NOT greater than 7 500 W;
  (c) gross weight NOT greater than 250 kg

FREEZERS, spiral, direct drive, programmable logic controlled, 
including ALL of the following:
  (a) stainless steel conveyors; 
  (b) stainless steel tube AND aluminium fin evaporator coils;
  (c) sequential hot gas defrost including ALL of the following:
           (i) NOT less than five individual evaporator coils;
          (ii) variable frequency drive fan motors;
         (iii) coil baffles;
          (iv) defrost program,
  (d) cleaning in place module including BOTH of the following:
           (i) skid;
          (ii) trough,          
  (e) shredding capacity exceeding 3 400 kg per hour,
with OR without ANY of the following:
           (i) coils;
          (ii) fans;
         (iii) pumps;
          (iv) console

ICE CREAM WORKSTATION, including ALL of the following:
  (a) one fixed cabinet;
  (b) two mobile cabinets;
  (c) freezers;
  (d) display tubs;
  (e) adjustable temperature;
  (f) work bench with LED illumination;
  (g) wheels;
  (h) electrical sockets;
  (i) sink;
  (j) taps;
  (k) drawers
with OR without trays AND/OR lids

COOLER, WAFER SANDWICH, spiral

DRY ICE MAKING MACHINES, DISCS AND/OR SLICES AND/OR BLOCKS 
AND/OR PELLETS, having a power output NOT less than 11 kW

TUNNEL FREEZERS, FRENCH FRIES AND/OR WEDGES, with OR without 
coils AND/OR motors, having ALL of the following:
  (a) throughput capacity NOT less than 18 tonnes per hour;
  (b) infeed height NOT less than 2 500 mm;
  (c) discharge height NOT less than 2 200 mm;
  (d) product discharge temperature NOT less than -18 degrees
      Celsius;
  (e) stainless steel conveyors

WATER COOLERS, having a storage capacity NOT less than 75 litres 
and NOT greater than 480 litres, with OR without ANY of the 
following:
  (a) taps;
  (b) drip trays;
  (c) compressors

SOFT SERVE MACHINES, with integrated blender

BATCH FREEZERS, ICE CREAM AND/OR GELATO AND/OR FROZEN DESSERTS, 
with or without spatulas

SPIRAL COOLER AND FREEZER LINE, BAKERY, including ALL of the 
following:
  (a) coolers;
  (b) freezer;
  (c) input AND/OR output conveyors;
  (d) belt washer;
  (e) pressurised air outlets;
  (f) fan;
  (g) control panel

ICE MAKING MACHINES, flakes AND/OR cubes, having ALL of the 
following: 
  (a) cube production NOT greater than 1 500 kg per 24 hours; 
  (b) power input NOT greater than 4 000 W; 
  (c) gross weight NOT greater than 250 kg; 
  (d) power supply NOT greater than 1O A

BLAST FREEZER LINE, programmable logic controlled, having ALL of 
the following:
  (a) ammonia evaporators;
  (b) chain conveyor;
  (c) trays;
  (d) air balance unit

FREEZER AND/OR COOL ROOMS, including BOTH of the following:
  (a) high-density polyurethane panels;
  (b) cooler AND/OR freezer unit

LIQUID AND ICE SYSTEM, programmable logic controlled, including 
ALL of the following:
  (a) additive storage AND dosing module;
  (b) additive dissolver;
  (c) brine supply pump;
  (d) ice slurry generator;
  (e) insulated ice slurry buffer AND storage tank incorporating
      an agitator;
  (f) discharge dosing counter AND/OR liquid weighing hopper

SOFT SERVE ICE CREAM AND THICK SHAKE MACHINES, including ALL of 
the following:
  (a) mix level AND temperature sensors;
  (b) peristaltic pump syrup delivery unit;
  (c) pasteuriser;
  (d) soft serve AND shake dispensing units;
  (e) two freezers;
  (f) touch panel

WATER CHILLERS, air cooled, 400 V, having ALL of the following:
  (a) cooling capacity exceeding 53 kW and NOT exceeding 494 kW;
  (b) axial fan power NOT greater than 20 kW;
  (c) galvanized steel frame AND panels;
  (d) compressor input power NOT greater than 107.3 kW
For the purpose of this concession (a) cooling capacity is based 
on:
    (i) outlet water temperature of 9 OR 15 degrees Celsius;
   (ii) ambient temperature of 25 degrees Celsius

BATCH FREEZERS, ICE CREAM OR GELATO, programmable logic 
controlled, having a maximum production capacity NOT less than 
20 L per hour

CHILLERS, WATER COOLED, having a cooling capacity either NOT 
greater than 200 kW or NOT less than 3517 kW

BEVERAGE CHILLERS, AC, with OR without dispensing faucets, 
having ALL of the following:
  (a) stainless steel casing;
  (b) coils; 
  (c) refrigeration compressor AND condenser;
  (d) insulated plastic reservoir coolant tank;
  (e) power rating NOT less than 220 V and NOT greater than 240 V

SPIRAL COOLER AND FREEZER, BREAD PRODUCTION LINE, programmable 
logic controlled, having interconnecting conveyor

BLAST CHILLERS AND/OR FREEZERS, having a maximum capacity of NOT 
less than 40 trays

COMPRESSION REFRIGERATORS, with OR without cup warmer AND/OR 
water tank, having a storage capacity NOT greater than 15 L

BLAST FREEZER ROOMS, having ALL of the following:
  (a) weight NOT less than 2 000 kg;
  (b) transport rails;
  (c) stainless steel floor and wall and roof panels;
  (d) NOT less than 6 transport racks having NOT less than 14
      trays per rack;
  (e) individual rack weight NOT less than 250 kg;
  (f) heat recovery system

CHILLERS, WATER, lithium bromide absorption, having ALL of the 
following:
  (a) evaporator;
  (b) absorber:
  (c) condenser;
  (d) pumps;
  (e) control panel;
  (f) heat exchanger;
  (g) generator

PELLETISERS, DRY ICE

ICE MAKERS, FLAKES AND/OR CUBES, having a cube production 
capacity NOT greater than 130 kg per 24 hours

ICE CREAM AND FLAVOURED ICE MAKING MACHINES, MOULDING AND 
FREEZING, having a maximum production capacity NOT less than  
500 units per hour

CHILLERS, WATER, WALL MOUNTED, having ALL of the following:
  (a) stainless steel tank having a maximum capacity NOT
      less than 50 L;
  (b) stainless steel cooling coil;
  (c) remote control panel;
  (d) weight not less than 125 kg;
  (e) draining maximum capacity NOT less than 90 L/h at 
      30 degrees Celsius to 180 degrees Celsius;
  (f) 3 phase power

BLAST CHILLERS AND/OR FREEZERS, self-adapting, programmable 
logic controlled

CHILLERS, air cooled, having a cooling capacity EITHER NOT 
greater than 200kW or NOT less than 950kW.

DISPENSERS, FROZEN BEVERAGE

CONTAINERS, FOOD, stainless steel interior, insulated, 
refrigerated, whether or not wheeled

DISPENSERS, FROZEN CARBONATED BEVERAGE

CHILLERS AND/OR FREEZERS, BLAST, having ALL of the following:
  (a) weight NOT less than 40 kgs;
  (b) tray capacity NOT greater than 40 trays; 
  (c) input power NOT less than 230 V

DISPENSERS, BEER

REFRIGERATION UNITS, TRAILER, TRANSPORT, having a minimum cooling
 capacity of 15 000 W (52 000 BTU/h) at 2 degrees C box temperature
 in 38 degrees C ambient

REFRIGERATION UNITS, TRAILER, TRANSPORT, having BOTH of the
 following:
   (a) minimum cooling capacity of 9 500 W (32 395 Btu/h) at 1.7
       degree C box temperature in 37.8 degree C ambient;
   (b) operational refrigerant fluid not containing chlorine

FREEZERS, INDIVIDUAL QUICK FREEZING (IQF)

MAKERS, FLAKE ICE

REFRIGERATORS, compression, 12 OR 24 volt DC AND/OR 240 volt AC 
powered

REFRIGERATORS, compression, having ALL of the following:
   (a) capacity NOT greater than 100 L;
   (b) combined or separate freezer compartments;
   (c) power source being 12/24 volt DC and/or 240 volt AC

COOLERS, portable, comprising ALL of the following:
   (a) insulation;
   (b) 12 volt DC AND/OR 24 volt DC AND/OR AC;
   (c) carry handles;
   (d) volume NOT greater than 115 litres

FREEZERS, FLAT FOOD, IMPINGEMENT

ICE CREAM MACHINES, CONTINUOUS, maximum capacity within range of 350
 to 450 litres per hour

DISPENSING KITS, domestic refrigerator, door mounted,
 being EITHER of the following:
   (a) ice making dispensers;
   (b) ice making and cold water dispensers

PARTS, FREEZER, being evaporators having 800 mm fans

PARTS, being condensers, having ALL of the following:
  (a) fan motor blade diameter 500 mm OR 630 mm OR 800 mm;
  (b) heat exchanger coils;
  (c) fin surface with spacing NOT greater than 3 mm in diameter;
  (d) maximum operating pressure NOT greater than 32 bar

EVAPORATORS, AIR COOLING, with OR without defrost heaters, 
having ALL of the following:
  (a) fans;
  (b) airflow NOT less than 450 m3/hr;
  (c) fan diameter NOT less than 195 mm and NOT greater than 630 
mm;
  (d) dry weight NOT less than 5 kg

CONDENSERS, REFRIGERATION, air cooled, having ALL of the 
following:
  (a) heat exchanger coils;
  (b) axial fans;
  (c) electronic fan speed controllers

PARTS, REFRIGERATION SYSTEM, being suction accumulators having 
BOTH of the following:
  (a) inlet AND outlet connectors;
  (b) safe working pressure NOT less than  2 500 kPa

ASSEMBLIES, REFRIGERATION CONDENSOR AND COMPRESSOR, including 
ALL of the following:
  (a) condenser;
  (b) compressor;
  (c) receiver tank;
  (d) metal base

ASSEMBLIES, REFRIGERATION CONDENSOR AND COMPRESSOR, including 
ALL of the following:
  (a) condensers;
  (b) compressors;
  (c) receiver tanks;
  (d) valves;
  (e) fan motor;
  (f) metal support base

PARTS, HEAT PUMP, being condensers

LIQUID RECEIVER TANKS, REFRIGERATION SYSTEM, having inlet and 
outlet connectors

PARTS, EVAPORATIVE AIR CONDITIONING SYSTEM, being copper refnet 
joints, complying with Australian and New Zealand Standard 
1677-2 (AS/NZ 1677-2), having ALL of the following:
  (a) inlet NOT less than 6 mm and NOT greater than 50 mm;
  (b) outlet NOT less than 6 mm and NOT greater than 50 mm;
  (c) length NOT less than 100 mm and NOT greater than 1 000 mm

PANELS, VACUUM INSULATION, DOMESTIC REFRIGERATOR

ASSEMBLIES, CONTROL HOUSING, REFRIGERATOR, DOMESTIC, comprising 
NOT less than ANY three of the following:
  (a) housings;
  (b) thermostats;
  (c) shafts;
  (d) baffles, whether or not motorised;
  (e) baffle casings;
  (f) insulation;
  (g) light and/or heat shields;
  (h) gaskets;
  (i) seals;
  (j) knobs;
  (k) labels and/or stickers;
  (l) lamp holders;
  (m) lamps;
  (n) clips;
  (o) printed circuit boards;
  (p) wiring harnesses;
  (q) terminals and/or connectors;
  (r) air curtains;
  (s) mounting bases;
  (t) timers;
  (u) logo displays

PARTS, REFRIGERATOR, DOMESTIC, being ANY of the following and 
whether or not in assemblies:
   (a) refrigerator and/or freezer baskets;
   (b) handles;
   (c) fascia and/or cabinet panels;
   (d) inserts;
   (e) assemblies, comprising fan and shroud;
   (f) covers;
   (g) housings;
   (h) ice and/or cold water modules;
   (i) mullions;
   (j) plates;
   (k) troughs;
   (l) hinges;
   (m) assemblies, freezer light, comprising cage, lamp and lamp
       holder;
   (n) bins;
   (o) levelling legs;
   (p) handle pedestals;
   (q) heat shields;
   (r) vents;
   (s) water sumps;
   (t) door assists;
   (u) condensers;
   (v) control boards;
   (w) clips;
   (x) trays;
   (y) corner seals;
   (z) strainers;
  (aa) corner braces

PARTS, ICE MAKER AND/OR COLD WATER DISPENSER, DOMESTIC 
REFRIGERATOR, being ANY of the following:
  (a)  motor rails;
  (b)  controls;
  (c)  dispensers;
  (d)  fascias;
  (e)  ice makers;
  (f)  ice chutes;
  (g)  paddles;
  (h)  ice buckets;
  (i)  clips;
  (j)  sumps;
  (k)  gates;
  (l)  knockout pins;
  (m)  inserts;
  (n)  housings;
  (o)  covers;
  (p)  snubbers;
  (q)  frames;
  (r)  sleeves;
  (s)  arms;
  (t)  shrouds;
  (u)  end caps;
  (v)  shields;
  (w)  casings;
  (x)  anchors;
  (y)  plates;
  (z)  retainers;
  (aa) rods;
  (ab) crusher screws;
  (ac) augers;
  (ad) auger motor assembly, comprising ALL of the following:
          (i) solenoid;
         (ii) wire harness;
        (iii) motor;
         (iv) shield;
          (v) lamp holder;
         (vi) mounting bracket

COOLING ASSEMBLIES, REFRIGERATOR, leak free when subjected to
 internal pressure of NOT less than 1.4 MPa, comprising ALL of the
 following:
   (a) evaporator;
   (b) thermostat;
   (c) thermal fuse;
   (d) defrost heater

PARTS, REFRIGERATOR, being ANY of the following:
   (a) shelves;
   (b) gaskets;
   (c) endcaps

PARTS, COOLING UNITS, CONTINUOUS CYCLE ABSORPTION, comprising ALL of
 the following:
   (a) condenser;
   (b) evaporator;
   (c) gas temperature exchanger;
   (d) liquid temperature exchanger;
   (e) absorber;
   (f) absorber vessel;
   (g) pump;
   (h) water separator;
   (i) boiler

HEATERS, CAMPING, WATER, having EITHER of the following:
   (a) battery DC voltage NOT less 6 volts;
   (b) gas power

THERMODYNAMIC SOLAR HOT WATER SYSTEM, having a refrigerant 
circulating thermal collector, consisting of All of the 
following:
  (a) condenser;
  (b) compressor;
  (c) expansion valve;
  (d) magnesium anode;
  (e) thermodynamic block;
  (f) electronic controller, 
with OR without supplementary coil

PANELS, SOLAR COLLECTOR, WATER HEATER

HEATERS, WATER, programmable logic controller, having BOTH of 
the following:
  (a) solar panels;
  (b) sun trackers

HEATERS, WATER AND AIR SPACE, vehicle mountable, diesel powered, 
having BOTH of the following:
  (a) air space heating power capacity NOT greater than 8 kW;
  (b) water heating temperature capacity NOT greater than 
      70 degrees Celsius

PANELS, SOLAR COLLECTOR, WATER HEATER

HEATERS, WATER, programmable logic controller, having BOTH of 
the following:
  (a) solar panels;
  (b) sun trackers

WATER HEATERS, DIESEL OR PETROL, having an output heat rating
 NOT exceeding 13 kW

STERILISERS, CULTURE MEDIA, comprising ALL of the following:
   (a) vessel with capacity range of 9 L to 100 L;
   (b) pressure gauges;
   (c) temperature chart recorder;
   (d) paddle and monitor

DISINFECTOR, MEDICAL, ENDOSCOPE APPARATUS, having an option
 controlled sequence of immersions, rinses and alcohol purges

STERILISER MACHINES, MEDICAL, steam, having ALL of the 
following:
  (a) chamber size NOT less than 7 120 mm in length and NOT less
      than 1 930 mm in height;
  (b) pumps;
  (c) heat exchanger;
  (d) pipes;
  (e) valves;
  (f) filters

AUTOCLAVES, SATURATED STEAM STERILISATION

DENTAL INSTRUMENT STERILISERS, BENCH TOP

STERILISERS, STEAM, BENCH TOP, DENTAL AND/OR MEDICAL, having 
BOTH of the following:
  (a) pre-vacuum and post vacuum cycle controls; 
  (b) chamber volume capacity NOT greater than 30 L

DENTAL INSTRUMENT STERILISERS, BENCH TOP, having ALL of the 
following:
  (a) pre-vacuum AND post vacuum cycle controls;
  (b) prion cycle control capacity NOT greater than 137 degrees
      Celsius at 18 minutes;
  (c) volume capacity NOT greater than 30 L

MEDICAL MOBILE STEAM STERILISERS, including ALL of the following:
  (a) jacketed sterilisation chamber module;
  (b) utility module with steam generator;
  (c) process controller;
  (d) pre-vacuum sterilisation cycle;
  (e) weight NOT greater than 350 kg;
  (f) on board printer

STERILISATION CHAMBERS, MEDICAL AND/OR LABORATORY, having BOTH of
 the following:
   (a) continuous operation at pressures NOT greater than 220 kPa;
   (b) chamber heating NOT greater than 60 degrees Celsius with
       temperature stratification LESS than 3 degrees Celsius

FLUID BED DRYING SYSTEM, consisting of ALL the following:
  (a) shaking fluid bed dryer;
  (b) air supply system;
  (c) natural gas fired heater with OR without ductwork;
  (d) water chiller;
  (e) exhaust air unit;
  (f) cyclone separator;
  (g) cartridge filter;
  (h) dust collection cone,
with OR without ANY of the following:
          (i) exhaust air AND/OR duct transition pieces;
         (ii) exhaust cyclone inlets AND outlets;
        (iii) exhaust air duct

DRYERS, YANKEE, having BOTH of the following:     
  (a) outside diameter NOT greater than 5 400 mm; 
  (b) web width on dryer NOT greater than 4 000 mm

KILNS, TIMBER CONDENSATION DRYING, plc, having BOTH of the
 following:
   (a) variable temperature zones;
   (b) moisture content and temperature sensors

KILNS, TIMBER DRYING, plc, thermal oil heated, having BOTH of
 the following:
   (a) variable temperature zones;
   (b) moisture content and temperature sensors

FREEZE DRYERS, PHARMACEUTICAL, having BOTH of the following:
  (a) condenser ice capacity NOT greater than 60 kg;
  (b) condenser temperature NOT less than minus 60 degrees  
      Celsius

SPRAY DRYERS, having ALL of the following:
  (a) rotary OR two-fluid nozzle atomisation;
  (b) compressed air capacity NOT greater than 6 bar;
  (c) water evaporation capacity NOT greater than 7 kg/hour

FREEZER DRIERS, BENCH TOP, programmable logic controlled, 
having ALL of the following:
  (a) ice condenser temperature capacity of -52 degrees C 
      OR colder;
  (b) minimum condenser volume capacity NOT less than 3 L;
  (c) hot gas defroster;
  (d) touchscreen control panel;
  (e) bleed valve vacuum control

SPRAY DRYERS, including ALL of the following:
  (a) atomisation nozzles;
  (b) one OR more fluid beds;
  (c) retractable cleaning nozzles AND/OR spray balls;
  (d) ducts OR vents;
  (e) exhaust filter,
with OR without EITHER of the following:
            (i) homogeniser;
           (ii) heat exchanger OR radiator

DRYING LINES, AGRICULTURAL PRODUCE, programmable logic 
controlled, including ALL of the following:
  (a) storage bin AND/OR feeder;
  (b) electro-magnetic hammer;
  (c) conveyors;
  (d) hot air dryers;
  (e) heater shell;
  (f) LPG burner;
  (g) leaf shredder

DRYING TUNNELS, FRUIT, including ALL of the following:
  (a) hot air generators;
  (b) fans;
  (c) bucket OR roller conveyors,
with OR without gas OR diesel burners

AIR DRYING LINE, VEGETABLE LEAF, programmable logic controlled, 
having ALL of the following:
  (a) dewatering station;
  (b) shaker;
  (c) air drying AND cooling tunnel;
  (d) conveyors; 
  (e) beater bar WITH motor;
  (f) platforms;
  (g) control cabinet WITH touch screen

HOT AIR DRYING SYSTEMS, WOOD PELLETS, air volume NOT less than 
1 800 m3/hr AND with OR without infeed AND/OR outfeed conveyors, 
having BOTH of the following:
  (a) dryer;
  (b) drying hopper

DRYERS, WALKING FLOOR, WOOD CHIP, containerised

KILNS, TIMBER DRYING, plc, thermal oil heated, having BOTH of
 the following:
   (a) variable temperature zones;
   (b) moisture content and temperature sensors

KILNS, TIMBER CONDENSATION DRYING, plc, having BOTH of the
 following:
   (a) variable temperature zones;
   (b) moisture content and temperature sensors

DRYERS, YANKEE, having BOTH of the following:     
  (a) outside diameter NOT greater than 5 400 mm; 
  (b) web width on dryer NOT greater than 4 000 mm

DRYING UNIT, having ALL of the following:
  (a) walking floor receiving deck;
  (b) screw conveyor AND/OR auger;
  (c) drum dryer infeed;
  (d) drum dryer;
  (e) heat generator;
  (f) cyclone

DRYERS, dehumidifying, using molecular sieve material to remove
 moisture from plastic granules prior to moulding or extrusion,
 at a drying air dewpoint to -40 degrees C, but NOT
 including dehumidifying dryers imported with insulated drying
 storage hoppers

FREEZE DRIERS, industrial, having BOTH of the following:
   (a) condenser ice capacity of 15 kg or greater with ice thickness
       of 20 mm;
   (b) condenser temperature of - 60 degrees C or lower

SPRAY DRYERS, laboratory, having a total solution/suspension
 processing capacity NOT exceeding 1 L

DRYERS, MELAMINE SHEETING, with a processing speed NOT less 
than 50 m/min and NOT greater than 300 m/min

DRYER PLANT, SEWERAGE SLUDGE, whether OR not assembled, having 
BOTH of the following:
  (a) recuperators;
  (b) sludge crushers

DRYING MACHINES, BEVERAGE CAN, having ALL of the following:
  (a) process AND/OR production rate NOT less than
      2 300 cans per minute;
  (b) operating temperature NOT less than 165 degrees C;
  (c) glass conveyor belt

DRYERS, INDUCTION COMPOUND, FOOD CAN END, air cooled, single 
AND/OR dual lane, programmable logic controlled, having BOTH of 
the following;
  (a) production line speed NOT greater than 2 200 can ends per  
      minute per lane;
  (b) steel can end diameter NOT less than 57 mm and NOT 
      greater than 170 mm steel ends

DRYING MACHINES, METAL ROD AND/OR METAL WIRE, including BOTH of 
the following:
  (a) heaters;
  (b) fans

INK CURING MACHINES, ULTRA VIOLET LIGHT, having ALL of the 
following:
  (a) water cooled press chill roller;
  (b) cooling fan;
  (c) lamp having a rated power NOT greater than 201 watts  
      per centimetre;
  (d) print width NOT greater than 461 mm

HEATERS, WHEAT GLUTEN AND STARCH PROCESSING, natural gas, direct 
fired, having ALL of the following: 
  (a) vertical upwards firing;
  (b) gas valve train;
  (c) control panel;
  (d) burner management system;
  (e) automated control flaps

BELT DRYERS, SEWERAGE SLUDGE, having BOTH of the following:
  (a) recuperators;
  (b) exhaust fans

DRYERS, RE-CYCLED POLYETHYLENE TEREPHTALATE FLAKES, having ALL 
of the following:                                                
  (a) feeding screws with OR without metal detectors AND 
      separators;
  (b) hot air dryers;
  (c) water condensers;
  (d) air filters;
  (e) pre-drying units having air filters AND condensate 
      separators;
  (f) gas AND/OR electric heaters

DRYERS, FLASH AND/OR RING, unassembled, with OR without 
centrifugal classifier AND/OR motor

STARCH DRYERS, including ALL of the following:
  (a) dust collector;
  (b) screw conveyors;
  (c) steam heating unit;
  (d) blower;
  (e) electrical controls

OVENS, ULTRAVIOLET, having ALL of the following:
 (a) mercury UV (ultraviolet) lamps;
 (b) gallium UV (ultraviolet) lamps;
 (c) double chain conveyor;
 (d) compressed air supply

VACUUM BELT DRYERS, steam heated AND/OR water cooled, with OR 
without ANY of the following:
  (a) vacuum system having pumps AND/OR condensers;
  (b) heating AND/OR cooling system having plates AND/OR valves;
  (c) ingredient transfer AND/OR feeding system, including
      ALL the following:        
          (i) pumps; 
         (ii) valves;
        (iii) piping;
         (iv) hoses,
  (d) infeed hopper having valves;
  (e) filter;
  (f) controls

DRYER, CERAMIC MEDIA, FLUID BED, programmable logic controlled, 
natural gas

CURING AND DRYING CHAMBERS, PASTED BATTERY PLATE, programmable 
logic controlled, including ALL of the following:
  (a) humidity generator;
  (b) heat recovery system having an air to air heat exchanger;
  (c) heat exchanger;
  (d) ventilators AND/OR exhausters;
  (e) temperature AND/OR humidity controls;
  (f) air ducts,
with OR without ANY of the following:
           (i) vertical rolling doors;
          (ii) internal partition walls;
         (iii) radio remote controls;
          (iv) directional control valves;
           (v) control cabinets AND/OR panels;
          (vi) tilting flap;
         (vii) humidity AND/OR temperature probes AND/OR
               sensors;
        (viii) electrical cables AND/OR connectors;
          (ix) chimney;
           (x) pipes AND/OR mountings AND/OR fittings

DRYING PLANT, SULPHATE OF POTASH, natural gas, comprising ALL of 
the following:
  (a) shaking fluid bed dryer;
  (b) bi-directional screw conveyor;
  (c) air blowers;
  (d) air heater;
  (e) breeches chute;
  (f) dust cyclone;
  (g) wet scrubber

DRYERS, VACUUM DRUM, having ALL of the following:
  (a) cast iron drums;
  (b) electrical drive units;
  (c) knife holder;
  (d) feed AND distribution pipes;
  (e) steam AND condensate system;
  (f) stainless steel vacuum encasing

CURING OVENS, having ALL of the following:
  (a) ultraviolet lamp;
  (b) software interface;
  (c) conveyor

DRYING TUNNELS, forced ventilation, hot air

DRYING OVENS, GAS, tinplate, having ALL of the following:
  (a) drying temperature NOT less than 160 degrees Celsius and 
      NOT greater than 210 degrees Celsius;
  (b) air purification unit;
  (c) infeed AND outfeed conveyors;
  (d) cooling zone

DRYERS, PRINTING INK, infrared, including ALL of the following:
  (a) positive air pressure chambers;
  (b) aluminium reflectors;
  (c) air bars;
  (d) short wave infrared lamps;
  (e) high temperature glass;
  (f) smoke detection;
  (g) blowers

DEHUMIDIFYING DRYERS, PLASTIC GRANULE, including ALL of the 
following:
  (a) molecular sieves desiccant towers;
  (b) blowers;
  (c) hoppers;
  (d) heating booster;
  (e) vacuum pumps;
  (f) support frame

DRYERS, SILICEOUS MATERIAL, vibrating, including ALL of the 
following:
  (a) perforated plates;
  (b) heating fan;
  (c) cooling fan;
  (d) filters

DRYERS, including BOTH of the following:
  (a) infrared lamps;
  (b) conveyor

DRYERS, including ALL of the following:
  (a) temperature AND humidity control;
  (b) air inlet AND outlet;
  (c) fans;
  (d) sensors;
  (e) exhaust;
  (f) recirculation control

HEATERS, fanless, including ALL of the following:
  (a) ingress protection IP20;
  (b) power NOT less than 1.75 kW;
  (c) electronic temperature control

REFRIGERATED AIR DRYERS, having ALL of the following:
  (a) air flow capacity NOT less than 20 m3/h at 25 degrees C
      ambient temperature;
  (b) single phase OR multi-phase power supply;
  (c) digital controller;
  (d) air to refrigerant heat exchanger;
  (e) air to air heat exchanger;
  (f) water OR air cooled condenser

DRYERS, programmable logic controlled, including ALL of the 
following:
  (a) vertically stacked dryer decks;
  (b) maximum drying efficiency NOT less than energy
      consumption 2 660 kJ/kg water;
  (c) moisture controls;
  (d) vertical ambient air cooler

DRYERS, AIR, HEAT OF COMPRESSION

ROTARY DRYER DEHYDRATING SYSTEM, skid mounted, programmable 
logic controlled, having ALL of the following:
  (a) output capacity NOT greater than 1 000 kg per hour;  
  (b) rotary dryer unit;
  (c) sealed floor;
  (d) dust extraction system;
  (e) exhaust system;
  (f) fan;
  (g) coagulator;
  (h) in-line mill;
  (i) condenser

DRYING AND HEATING MODULE, ASPHALT PLANT

DRYERS, PAINT, infrared

DRYERS, AGGREGATE, fluid bed, natural gas

MACHINES, PAINT CURING, AUTOMOTIVE, gas operated

PLASTICS HANDLERS, plc, comprising BOTH of following:
  (a) desiccant dryers;                              
  (b) vacuum conveyors

DRYERS, PLASTIC GRANULATES, CONTINUOUS, having a hopper

DRYERS, COMPRESSED AIR, FRIDGE and/or ADSORPTION

DRYERS, AIR, having ALL of the following:
   (a) capacity between 1 000 cu m/h and 2 000 cu m/h;
   (b) minimum 400 V/50 Hz electric motor;
   (c) provision for refrigerant to be attached;
   (d) air/water heat exchanger;
   (e) evaporator heat exchanger

EVAPORATORS, vacuum, laboratory, having ALL of the following
 characteristics:
   (a) rotation of evaporator flask;
   (b) heating of the flask using a water bath;
   (c) speed and temperature controls for (a) and (b) respectively

SOLVENT DISTILLATION UNITS, of the non-continuous atmospheric
 pressure batch type

HEAVY HYDROCARBON REMOVAL UNIT, module, steel-framed, having ALL 
the following:
  (a) height NOT less than 25 metres;
  (b) weight NOT less than 2,000,000 kilograms;
  (c) heat exchangers;
  (d) vessels

WATER TREAMENT AND/OR FILTRATION SYSTEM, programmable logic 
controlled, including ALL of the following:
  (a) distiller columns;
  (b) condensers;
  (c) drain recovery heat exchanger;
  (d) drain cooler;
  (e) valves;
  (f) electrical instruments;
  (g) piping AND/OR fittings;
  (h) centrifugal pump;
  (i) filter;
  (j) control panel;
  (k) skid mounted

STILLS, ALCOHOL DISTILLATION PLANT, pot AND column, having ALL 
of the following:
  (a) 3 000 litre pot still;
  (b) concentration columns;
  (c) heat exchangers; 
  (d) condenser;
  (e) agitator; 
  (f) botanical column; 
  (g) 3 chamber collector; 
  (h) thermometers; 
  (i) tanks

PYROMETALLURGICAL MELTING SYSTEM, METAL SEPARATION AND VACUUM 
DISTILLATION, having ALL of the following:
  (a) double walled vacuum chamber;
  (b) evaporating AND/OR cooling stations;
  (c) condensers;
  (d) melting group having an induction system;
  (e) control panel AND/OR sensor;
  (f) power generator cabinet;
  (g) vacuum pump AND/OR vacuum valve system;
  (h) nitrogen distribution system;
  (i) closed loop water cooling system

CONTINUOUS DISTILLATION COLUMNS, EXTRA NEUTRAL ALCOHOL 
PRODUCTION PLANT

EVAPORATORS, MECHANICAL VAPOUR RECOMPRESSION, including ALL of 
the following:
  (a) separator;
  (b) compressor;
  (c) pre-heater;
  (d) evapo-condenser

POT STILLS, ALCOHOL DISTILLATION PLANT, including ALL of the 
following:
  (a) vacuum pot stills;
  (b) batch concentration columns;
  (c) heat exchangers;
  (d) condensers;
  (e) coolers;
  (f) purifiers;
  (g) mixers;
  (h) tanks

DEALCOHOLISING MACHINES, programmable logic controlled, 
including ALL of the following:
  (a) vertical stripping column;
  (b) flow regulator;
  (c) liquid distributor;
  (d) steam generator;
  (e) stripping gas injector;
  (f) plate heat exchanger;
  (g) condensate cooler;
  (h) vapour condensor;
  (i) glycoside recirculation pump,
with OR without vacuum pumps AND/OR centrifuge separator

RECTIFIER COLUMNS, ALCOHOL DISTILLATION PLANT

CRYSTALLISERS, vacuum, programmable logic controlled, including 
ALL of the following:
  (a) control panel;
  (b) evaporation chamber;
  (c) heat exchangers;
  (d) pumps;
  (e) piping;
  (f) hot AND cold water production system consisting of BOTH of
      the following: 
         (i) pumps AND tanks module;
        (ii) control panel

EVAPORATORS, MECHANICAL VAPOUR RECOMPRESSION, programmable logic 
controlled, including ALL of the following:
  (a) control terminal;
  (b) heat exchangers;
  (c) ethernet interface;
  (d) blower;
  (e) boiling chamber;
  (f) pumps;
  (g) field instruments;
  (h) piping;
  (i) chemical cleaners

BEVERAGE ALCOHOL REDUCING OR ELIMINATING MACHINES, programmable 
logic controlled, including ALL of the following:
  (a) vertical alcohol stripping column; 
  (b) beverage flow regulator; 
  (c) liquid distributor outlets; 
  (d) steam generator; 
  (e) alcohol stripping gas injector;
  (f) plate heat exchanger;
  (g) condensate cooler;
  (h) vapour condenser;
  (i) vacuum pump;
  (j) coolant recirculation pump

ANHYDROUS HYDROGEN CHLORIDE GAS EXTRACTION PLANT, skid mounted, 
including ALL of the following:
  (a) distiller, including ALL of the following:
         (i) distillation column;
        (ii) reboiler;
       (iii) overhead condenser,
  (b) calcium chloride regenerator, including ALL of the  
      following:
         (i) reboiler;
        (ii) pumps;
       (iii) flash drum;
        (iv) water condenser,  
  (c) dryer, including ALL of the following:
         (i) chilled condenser;
        (ii) chilled demister;
       (iii) molecular sieve towers;
        (iv) nitrogen heater;
         (v) gas injector with a gas accumulator,
  (d) skids;
  (e) pipes;
  (f) valves

WASTE OIL DISTILLING SYSTEM, including ALL of the following:
  (a) pumps;
  (b) evaporator;
  (c) condenser;
  (d) heat exchanger

OIL DISTILLING AND SEPARATING SYSTEM, including ALL of the 
following:
  (a) condensers;
  (b) control panel;
  (c) evaporators;
  (d) heat exchanger;
  (e) piping;
  (f) pumps;
  (g) separator;
  (h) valves

WATER DISTILLATION MACHINES, programmable logic controlled, 
having BOTH of the following:
  (a) maximum water distillate output capacity NOT less 
      1 000 L/hr;
  (b) maximum operating energy input capacity NOT less than 
      90 kW

RECYCLERS, SOLVENT, steam AND/OR oil heated, having an operating 
temperature NOT greater than 200 degrees celsius

HEAT EXCHANGERS, manufactured from carbon or graphite

HEAT EXCHANGERS, finned, multi-stream, brazed aluminium plated,
 gas to gas service, having ALL of the following characteristics:
   (a) having EITHER of the following:
         (i) an overall heat transfer coefficient of
             340 900 W/sq m degrees C or greater;
        (ii) having surface to volume ratios of 1 000 sq m/cu m or
             greater;
   (b) capable of operating at temperatures of - 22 degrees C;
   (c) capable of operating at pressures of 690 kPa or greater

HEAT EXCHANGERS, PASSENGER MOTOR VEHICLE, being one OR both of 
the following
  (a) exhaust recuperation coolers;
  (b) charge air coolers

PLATE HEAT EXCHANGER, gasket free, having welded channels

HEAT EXCHANGERS, VERTICAL PLATE, having ALL of the following:
   (a) 316 stainless steel plates;
   (b) plates combined surface exceeding 189 sq m;
   (c) clean conditions heat transfer co-efficient exceeding
       5 200 W/sq m.K;
   (d) 27.6 bar (gauge) pressure;
   (e) 2-pass stream flow;
   (f) retaining bolts;
   (g) peripheral gaskets
 For the purposes of this order, ALL measurements have a tolerance of
 + OR - 5%

CHILLERS, AIR, having ALL the following:
   (a) length greater than 6 000 mm;
   (b) diameter greater than 50 mm;
   (c) heat duty 32 kW;
   (d) operation pressure, 500 kPa;
   (e) operation temperature, 0 degrees C to 50 degrees C

MATRIX, heat exchanger, aluminium brazed, fitted with internal
 tubulators and having ALL of the following features:
   (a) capable of withstanding 5 million cycles at 3 Hz between 0 and
       1 400 kPa at 50 degrees C;
   (b) capable of withstanding temperature shocks from steam at 104
       degrees C then water at 13 degrees C;
   (c) fitted with British Standard Pipe Parallel (BSPP) connections;
   (d) a maximum working pressure of 2 800 kPa

EXCHANGERS, oil cooler, skid steer loader, having BOTH of the
 following:
   (a) maximum working pressure of 3 447 kPa;
   (b) physical dimensions NOT exceeding width 630 mm x length 318 mm
       x depth 51 mm

HEAT EXCHANGERS, WELDED PLATE, having ALL of the following:
  (a) grating panels;
  (b) platform supports;
  (c) connecting sleeves;
  (d) bottom guidance axis;
  (e) support plate axis;
  (f) gussets;
  (g) shims;
  (h) intermediate plates;
  (i) plate supports;
  (j) spacers;
  (k) washers;
  (l) screws;
  (m) nuts;
  (n) lifting lugs;
  (o) centering pins;
  (p) centering washers;
  (q) bellows;
  (r) pipes;
  (s) flanges; 
  (t) conical grids;
  (u) mounting tools; 
  (v) nameplates;
  (w) pins;
  (x) bolts;
  (y) gaskets

GRANULATOR AIR HEATER, finned tube, having ALL of the following:
  (a) aluminium fins with a thickness NOT greater than 0.4 mm;
  (b) fin height NOT greater than of 15.375 mm;
  (c) tube bundles NOT greater than 192 tubes

HEAT EXCHANGERS, OIL, air cooled, electric, motor capacity NOT 
greater than 7.5 HP

STEAM HEATERS, EMISSION CONTROL, having BOTH of the following
  (a) tube side working pressure NOT less than 16 bar; 
  (b) tube side working temperature NOT less than 200 degrees 
   Celsius

VAPORISERS, METHANOL, having ALL of the following:
  (a) length NOT less than 9.7 metres;
  (b) width AND height NOT less than 2.9 metres; 
  (c) weight NOT less than 27.0 tonnes

PREHEATERS AND/OR REACTORS, emissions control system, having ALL 
of the following:
  (a) length NOT less than 9.5 metres;
  (b) width AND height NOT less than 2.39 metres; 
  (c) weight NOT less than 10.5 tonnes

HEAT EXCHANGERS, REACTOR, having ALL of the following:
  (a) length NOT less than 9.0 metres;
  (b) width AND height NOT less than 5.0 metres; 
  (c) weight NOT less than 58 tonnes

HEAT EXCHANGERS, cooling coil, including ALL of the following:
  (a) capacity NOT greater than 2000 kW;
  (b) tube inner volume NOT greater than 1310 L;
  (c) aluminium fins;
  (d) copper tubes

HEAT EXCHANGERS, PLATE AND SHELL

HEAT EXCHANGERS, steel strip metal coating line, including ANY 
of the following:
  (a) fans AND/OR Impellers AND/OR blowers;
  (b) U type heat exchanger; 
  (c) nitrogen-Hydrogen (HNX) gas jet cooling heat exchanger;
  (d) water quenching plate

HEAT EXCHANGERS, ELECTRIC IMMERSION, having BOTH of the 
following:
  (a) internal operating pressure NOT less than 0.42 MPa;
  (b) internal operating temperature NOT less than 350 degrees C

WATER COOLING DISTRIBUTION SYSTEM, including ALL of the 
following:
  (a) pumps;
  (b) inverters;
  (c) expansion vessels;
  (d) sensors;
  (e) heat exchangers;
  (f) monitors AND alarms;
  (g) controllers;
  (h) screen display;
  (i) valves;
  (j) filters;
  (k) flow meter;
  (l) pipes AND couplings;
  (m) dual power supplies with auto transfer switch;
  (n) air vents

AIR-COOLED HEAT EXCHANGER, modular, steel framed, weight NOT 
less than 2 000 ton and NOT less than 15 metres in height, 
including ALL of the following:
  (a) pipes AND tubes; 
  (b) stairs; 
  (c) platforms; 
  (d) supporting walkways; 
  (e) fencing; 
  (f) gates; 
  (g) ladders; 
  (h) spools; 
  (i) cable trays; 
  (j) air cooled heat exchangers, including ALL of the following:
          (i) fans;
         (ii) tube bundles;
        (iii) plenum chambers,
   with OR without ANY of the following: 
          (i) electric motors; 
         (ii) drives; 
        (iii) pumps; 
         (iv) electrical panels AND/OR switches AND/OR
              gauges; 
          (v) steel supports

HEAT EXCHANGERS AND WATER HEATERS, tube, including BOTH of the 
following:
  (a) shell volume NOT less than 5 L;
  (b) tube volume NOT less than 3 L

PROPANE REFRIGERATION MODULE, steel framed, including ALL of the 
following:
  (a) pipes;
  (b) stairs;
  (c) handrails;
  (d) heat exchangers;
  (e) weight NOT LESS than 3 000 tonnes;
  (f) height NOT LESS than 25 metres

ETHYLENE COLD BOX, LIQUEFACTION PLANT, having ALL of the 
following:
  (a) heat exchangers;
  (b) height NOT less than 19 m;
  (c) width NOT less than 10 m;
  (d) length NOT less than 21 m

HEAT EXCHANGERS, MOTOR COOLING, fan-forced air to air, having 
ALL of the following: 
  (a) NOT less than four separately driven fans;
  (b) aluminium tubes;
  (c) flow rate NOT less than 20 m3/s;
  (d) power dissipation NOT less than 400 kW; 
  (e) motor/fan rated output NOT less than 15 kW

HEAT EXCHANGERS, including ALL of the following:
  (a) minimum design metal temperature (MDMT) of 0 degrees C 
      at 70 bar;
  (b) tube side maximum allowable working pressure (MAWP) of
      300 degrees C at 70 bar;
  (c) tube side test pressure of 91 bar

VESSELS, PRE-HEATER, steam to air, having ALL of the following:
  (a) flow rate NOT less than 30 000 kg/hr and NOT greater than
      80 000 kg/hr;
  (b) stainless steel pressure shell AND tube heat exchanger;
  (c) differential pressure gauge;
  (d) filters;
  (e) steam trap;
  (f) manhole

MODULES, AIR-COOLED HEAT EXCHANGER, steel framed, weight NOT
less than 2 000 ton and NOT less than 15 metres in height 
including ALL of the following:
  (a) pipes AND tubes;
  (b) stairs;
  (c) platforms;
  (d) supporting walkways;
  (e) fencing;
  (f) gates;
  (g) ladders;
  (h) spools;
  (i) cable trays;
  (j) air cooled heat exchangers, including NOT less than ANY
      six of the following:
           (i) fans;
          (ii) electric motors;
         (iii) drives;
          (iv) pumps;
           (v) electrical panels, AND switches, AND gauges;
          (vi) plenum chambers;
         (vii) steel supports;
        (viii) bundles

HEAT EXCHANGE UNITS, plate, water-cooled, having ALL of the 
following:
  (a) stainless steel circulation pump;
  (b) touchscreen controller;
  (c) operating temperature NOT less than 3 degrees C and NOT 
      greater than 95 degrees C;
  (d) delivery pressure NOT greater than 4.7 bar;
  (e) heater element

HEAT EXCHANGE UNITS, including ALL of the following:
  (a) rotating bath pasteurisers;
  (b) cylindrical chamber;
  (c) energy skid;
  (d) pumps;
  (e) valves

MILK AND/OR CREAM COOLING SYSTEM, skid mounted, including ALL 
of the following:
  (a) valves;
  (b) flowmeter;
  (c) manifold;
  (d) tanks;
  (e) heat exchangers

PREHEAT EXCHANGERS, SULFURIC ACID PLANT

COMPRESSOR AFTERCOOLERS, OFFSHORE, modular, air-cooled, whether 
or NOT assembled, having ALL of the following:
  (a) NOT less than two six bladed fans;
  (b) electric motor;
  (c) structural support;
  (d) pipes;
  (e) tubes

HEAT EXCHANGE UNIT, tube in shell, including ALL of the 
following:
  (a) working pressure NOT greater than 13 bar;
  (b) operating temperature NOT greater than 184 degrees C;
  (c) steam cover;
  (d) pipes;
  (e) o-ring seals;
  (f) baffle plates;
  (g) tube bundle;
  (h) cylindrical shell housing

HEAT EXCHANGE UNITS, passive cooling, including BOTH of the 
following
  a) operating pressure NOT greater than 25 bar;
  b) length NOT less than 3 866 mm

MUD CHILLERS, ONSHORE WELL DRILLING, skid mounted, including 
ALL of the following:
  (a) evaporator;
  (b) compressors;
  (c) condensers;
  (d) tanks;
  (e) expansion device;
  (f) flow switch control;
  (g) cooling coils;
  (h) fans;
  (i) heat exchangers;
  (j) pump;
  (k) cables;
  (l) filter strainer skid;
  (m) skid lifting frame

HEAT EXCHANGERS, including ALL of the following:
  (a) NOT less than five fans;
  (b) motor capacity per fan NOT less than 3 kW;
  (c) stainless steel tubes;
  (d) aluminium fins;
  (e) valves;
  (f) control box

PANELS, hydronic radiant heating AND/OR cooling, assembled, 
having 
ALL of the following:
  (a) dry weight NOT greater than 4 kg/m2;
  (b) rhomboid shaped internal copper pipe having an outer   
      diameter NOT exceeding 10 mm;
  (c) internal copper pipe encapsulated with aluminium face
      plate;
  (d) panel length NOT less than 1.2 m and NOT greater than 6.0 m

REBOILERS, COLUMN, ETHANOL

INTERCOOLING SKIDS, GAS TURBINE, wet compression, including ALL 
of the following:
  (a) pump; 
  (b) motor;
  (c) piping;
  (d) spray nozzle banks;
  (e) measuring devices; 
  (f) variable speed drive;
  (g) filter;
  (h) ball valve

GENERATOR COOLERS, including ALL of the following:
  (a) inlets AND/OR outlets;
  (b) copper-nickel tubes;
  (c) aluminium fins;
  (d) detachable water boxes

WATER COOLING SYSTEM, CONVERTER VALVE, consisting of ALL of the 
following:
  (a) centrifugal pumps;
  (b) expansion tank;
  (c) ion exchanger AND ion exchanger circuit;
  (d) strainer;
  (e) coolers; 
  (f) valves;
  (g) control cubicle having BOTH of the following:
         (i) measuring instruments;
        (ii) main switches

SCRAPED SURFACE HEAT EXCHANGERS, whether OR not assembled, with 
OR without lifting device, including ALL of the following:
  (a) stainless steel cylinders;
  (b) stainless steel dasher;
  (c) scraper blades;
  (d) shaft seal;
  (e) drive motor;
  (f) heat exchange surface per cylinder NOT less than 0.15 m2
      and NOT greater than 0.90 m2;
  (g) flow rate NOT less than 1 900 litres per hour and
      NOT greater than 20 500 litres per hour

CHILLED BEAMS, RADIANT AND/OR CONVECTION COOLING, having a 
weight NOT greater than 8 kg/m

HEAT EXCHANGERS, rotating, continuous scraped surface, having 
ALL of the following:
  (a) helix mixing spiral integrated with scraper bar;
  (b) single OR multiple inner tubes;
  (c) replaceable inner tubes

COOLING UNIT, chilled water, having ALL of the following:
  (a) cooling capacity NOT greater than 70 kW;
  (b) network frequency NOT less than 50 Hz and NOT
      greater than 60 Hz;
  (c) input voltage NOT less than 100 V AC and NOT greater 
      than 415 V AC;
  (d) one OR three phase electric power,
with OR without EITHER of the following:
         (i) humidifier;
        (ii) re-heater

RADIATORS, remote-mounted, horizontal type, with OR without 
variable frequency drive, having ALL of the following:
  (a) radiator cooler circuits;
  (b) galvanised steel frame AND casing;
  (c) copper tubes;
  (d) aluminium fins;
  (e) fans;
  (f) valves;
  (g) railings;
  (h) access ladder

HEAT EXCHANGERS, including ALL of the following:  
  (a) finned height exceeding 1.6 m;
  (b) square tube pitch;
  (c) aluminium magnesium OR copper fins;
  (d) stainless steel tube; 
  (e) working pressure exceeding 10 bar

RECUPERATORS, GLASS FURNACE, including ALL of the following:
  (a) tube cages;
  (b) radiation recuperators OR double shells;
  (c) waste gas cones;
  (d) intermediate part OR T-piece;
  (e) waste gas flaps

HEAT EXCHANGERS, other than passenger motor vehicles, being one 
OR both of the following:
  (a) exhaust recuperation coolers;
  (b) charge air coolers

HEAT EXCHANGER UNITS, VAPOUR OR STEAM, ALCOHOL DISTILLATION PLANT

HEATING UNIT, FISH OIL, AQUACULTURE FEED MILL, including ALL of 
the following: 
  (a) plate heat exchange;
  (b) water loop with pump;
  (c) expansion vessel AND safety valve;
  (d) steam AND condensate valve AND trap;
  (e) temperature AND pressure transmitters;
  (f) thermometers;
  (g) strainers

HEAT EXCHANGERS, TUBE AND PLATE, having ALL of the following:
  (a) stainless steel shell;
  (b) maximum volume capacity NOT less than 15 m3;
  (c) outlet nozzles

INTERCOOLERS, WET AND DRY GAS COMPRESSOR

HEAT EXCHANGERS, INTERNAL COMBUSTION GAS ENGINE, having BOTH of 
the following:
  (a) weight NOT less than 35 kg and NOT greater than 694 kg; 
  (b) cooling ribs and/or fins

HEAT EXCHANGERS, MALTING KILN, vertical glass tube, having ALL 
of the following:
  (a) air hoods;
  (b) tube length NOT greater than 2 850 mm;
  (c) air flow NOT greater than 683 100 kg/h;
  (d) kiln air pressure loss on supply air NOT greater than 
      80 Pa;
  (e) kiln air pressure loss on exhaust air NOT greater than 
      155 Pa;
  (f) maximum operating temperature NOT greater than 110 degrees 
      Celsius

HEAT EXCHANGERS, including ALL of the following:
  (a) NOT less than six fans;
  (b) capacity per fan NOT less than 0.95 kW;
  (c) stainless steel cooling tubes;
  (d) aluminium fins

HEAT EXCHANGERS, refrigerant, finned tube, having ALL of the 
following:
  (a) electric cooling fans;
  (b) NOT less than 305 tubes per tube bundle;
  (c) tube bundle size NOT less than 13 300 mm in length;
  (d) operating temperature NOT less than 85 degrees C;
  (e) operating pressure NOT less than 2 413 kPaG;
  (f) heat transfer rate of finned tube NOT less than 25.565 
      W/m2k

HEAT EXCHANGERS, GAS AND OIL, finned tube, having ALL of the 
following:
  (a) electric cooling fans;
  (b) NOT less than 74 tubes per tube bundle on gas side;
  (c) NOT less than 230 tubes per tube bundle on oil side;
  (d) tube bundle size NOT less than 13 300 mm in length;
  (e) operating temperature NOT less than 120 degrees C;
  (f) operating pressure NOT less than 2 800 kPa;
  (g) heat transfer rate of finned tube NOT less than 18.7 W/m2K 
      on gas side;
  (h) heat transfer rate of finned tube NOT less than 11.86 
      W/m2K on oil side

COOLERS, FLUID, 400 V, having ALL of the following:
  (a) air AND/OR water heat exchangers;
  (b) cooling capacity exceeding 860 kW and NOT exceeding 
      1 400 kW;
  (c) galvanized steel frame;
  (d) axial fan input power NOT greater than 50.4 kW;
  (e) electrically commutated fan input power NOT greater than  
      39.20 kW
For the purpose of this concession (a) cooling capacity is based 
on a temperature difference of 10 degrees Celsius between water 
outlet temperature and ambient air

HEAT EXCHANGERS, fluid cooled, having BOTH of the following:
  (a) stainless steel coiled tubing;
  (b) insulated stainless steel body

VENTILATORS, HEAT RECOVERY, ceiling recessed OR wall mounted, 
having ALL of the following:
  (a) two path ventilation;
  (b) sensible AND latent heat transfer;
  (c) corrugated layered paper core NOT greater than 30 
      microns thick

HEAT EXCHANGE SYSTEM, OIL AND/OR GAS EXPLORATION AND/OR 
PRODUCTION PUMPING SYSTEM, skid mounted, including ALL of the 
following:
  (a) steel frame;
  (b) heat exchangers;
  (c) motor;
  (d) fans;
  (e) pipes AND/OR hoses, with OR without fittings;
  (f) valves

HEAT EXCHANGERS, LIQUID NATURAL GAS (LNG) CONDITIONING PLANT, 
being EITHER of the following:
  (a) shell AND tube heat exchangers, incorporating a gas
      impurity remover;
  (b) kettle type heat exchanger, incorporating a liquid propane 
      level controller

HEAT EXCHANGERS, air cooled, being ANY of the following:
  (a) lean amine coolers;
  (b) LP flash reflux condensers;
  (c) propane refrigeration condensers

WATER COOLING SYSTEM, including ALL of the following:
  (a) heat exchanger;
  (b) pumps;
  (c) filters;
  (d) thyristor valves;
  (e) ion exchanger;
  (f) tank

CONDENSERS, SHELL AND TUBE HEAT EXCHANGER

CHARGE AIR COOLERS, GAS FUELLED POWER PLANT ENGINE

HEAT EXCHANGER EVAPORATORS OR HEAT EXCHANGER CONDENSORS, AIR 
CONDITIONER, EXCAVATOR AND/OR EARTHMOVING VEHICLE AND/OR DUMP 
TRUCK

HEAT EXCHANGERS, SHELL AND TUBE, HOT OIL

HEAT EXCHANGERS, air cooled, finned tube, gas to air, having ALL 
of the following:
  (a) NOT less than 120 tubes per bundle;
  (b) tube bundle size NOT less than 12 500 mm in length;
  (c) complying with American Petroleum Institute (API)
      Standard 661;
  (d) maximum operating temperature NOT less than 140 degrees C;
  (e) heat exchanged capacity NOT less than 4 000 kw

HEAT EXCHANGERS, IMMERSION, STEEL STRIP ACID PICKLE LINE, 
tantalum, shell AND tube AND/OR open coil

HEAT EXCHANGERS, STEAM, OIL AND GAS WELL TESTING, having ALL of 
the following:
  (a) adjustable chokes;
  (b) working temperature NOT less than - 20 degrees C and NOT 
      greater than 160 degrees C;
  (c) steam consumption NOT less than 2 200 kg/h;
  (d) coil working pressure NOT less than 69 MPa;
  (e) heating capacity NOT less than 4,600 J/h

HEATSINKS, COMPUTER PROCESSING UNIT, comprising ALL of the 
following:
  (a) metal base plates;
  (b) cooling fins;
  (c) mounting clips

COOLERS, OIL, TRANSFORMER, water cooled, having ALL of the 
following:
  (a) double cooling tubes;
  (b) leak detectors;
  (c) shells;
  (d) tube plates

HEAT EXCHANGERS, PLATE, but not including air to air heat 
exchangers

COOLING ASSEMBLIES, REFRIGERATOR, DOMESTIC, leak free when 
subject to internal pressure of NOT less than 1.4 MPa, being 
heat exchangers comprising All of the following:
  (a) pressurised suction tubes; 
  (b) capillary tubes; 
  (c) spacers; 
  (d) grommets

COOLERS, TRANSMISSION OIL, EARTH MOVING EQUIPMENT AND OFF 
HIGHWAY DUMP TRUCKS

HEAT EXCHANGERS, WELDED PLATE, having ALL of the following:
  (a) grating panels;
  (b) platform supports;
  (c) connecting sleeves;
  (d) bottom guidance axis;
  (e) support plate axis;
  (f) gussets;
  (g) shims;
  (h) intermediate plates;
  (i) plate supports;
  (j) spacers;
  (k) washers;
  (l) screws;
  (m) nuts;
  (n) lifting lugs;
  (o) centering pins;
  (p) centering washers;
  (q) bellows;
  (r) pipes;
  (s) flanges; 
  (t) conical grids;
  (u) mounting tools; 
  (v) nameplates;
  (w) pins;
  (x) bolts;
  (y) gaskets

CONDENSERS, SHELL AND TUBE, WATER COOLED

HEAT EXCHANGERS, spiral, having two concentric spiral channels

HEAT EXCHANGERS, MALTING KILN, having a horizontal glass tube

COOLERS, WATER TO OIL, having ALL of the following:
  (a) minimum oil flow NOT less than 40 litres per minute and  
      maximum oil flow NOT greater than 610 litres pet minute;
  (b) minimum water flow rate NOT less than 8 litres per minute 
      and maximum water flow rate NOT greater than 305 litres
      per minute;
  (c) copper nickel tubes

PARTS, ON-ROAD TRUCKS HAVING A GROSS VEHICLE WEIGHT NOT LESS 
THAN 7.5 TONNES, being ANY of the following:
  (a) coolers;
  (b) evaporators;
  (c) condensers

HEAT EXCHANGERS, AIR TO AIR, having BOTH of the following:
  (a) compliance with Ingress Protection 54;
  (b) noise level NOT greater than 78 dB (A)

HEAT EXCHANGERS, AIR TO WATER, having BOTH of the following:
  (a) compliant to IP55;
  (b) noise level NOT less than 55 dB (A) and NOT greater than
      75 dB (A)

HEAT EXCHANGERS, AIR TO AIR, having BOTH of the following:
  (a) compliant to IP54;
  (b) noise level NOT less than 65 dB (A) and NOT greater than
      78 dB (A)

COOLERS AND/OR HEAT EXCHANGERS, LUBRICATION OIL, LEVELLER GEARBOX

HEAT EXCHANGERS, finned, multi-stream, brazed aluminium plated, 
gas to gas service

RADIATORS, TRANSFORMER, OIL COOLING

FRYERS, pressure, having BOTH of the following characteristics:
   (a) a capability to fry under pressure when the lid is closed;
   (b) a capability to fry when the lid is open

TEMPERING MACHINES, chocolate

POPCORN MAKING MACHINES

DISPENSERS, food topping, using a water bath for warming, capable
 of dispensing product from the original container

ROASTING MACHINES, raw coffee bean

COFFEE MACHINES, capsule, including ALL of the following: 
  (a) coffee outlet;
  (b) drip tray;
  (c) pressure rating NOT less than 16 Bar and NOT greater than 
      19 Bar; 
  (d) capsule insertion slot;  
  (e) capsule container

DISPENSING MACHINES, having ALL of the following:
  (a) one OR two OR three hoppers;
  (b) mixing chamber for each hopper;
  (c) tank OR water mains connection;
  (d) proportion adjustment control;
  (e) touch screen operation

DISPENSING MACHINES, having ALL of the following:
   (a) one OR two OR three hoppers;
   (b) mixing chamber for each hopper;
   (c) tank OR water mains connection;
   (d) proportion adjustment control;
   (e) push button operation

FOAMERS AND/OR DISPENSERS, HOT MILK

DISPENSING MACHINES, having ALL of the following:
   (a) one, two OR three hoppers;
   (b) mixing chamber for each hopper;
   (c) tank OR water mains connection;
   (d) proportion adjustment control;
   (e) push button operation

OVENS, rotary, having ALL of the following features:
   (a) a programmable controller capable of storing a minimum of
       40 programs;
   (b) vapour discharge valve control;
   (c) integral steam generation;
   (d) a minimum of 15 tray capacity

FOAMER/DISPENSERS, hot milk, automatic, but NOT including coffee
 making machines

CONFECTIONERY MACHINES, including ALL of the following:
  (a) mixing AND batching AND weighing stations;
  (b) doser AND buffer reservoirs;
  (c) in-feed screw conveyor;
  (d) weigher AND filler;
  (e) water heaters;
  (f) pumps;
  (g) control panels;
  (h) stirrers AND agitators;
  (i) pipes AND/OR ducts;
  (j) temperature AND pressure controls;
  (k) batch cookers;
  (l) cooler room

COOKING APPLIANCES, portable, being ANY of the following:
  (a) grill plates;
  (b) heating AND cooling plates
with OR without ANY of the following:
   (i) splash guards;
  (ii) cleaning scrapers

ELECTRIC COOKER AND/OR FRYERS, portable, with OR without either 
of the following:
  (a) baskets;
  (b) hanging frames

HAZELNUT ROASTER, vertical, including ALL of the following:
  (a) upper product feed hopper;
  (b) roasting chambers;
  (c) fire fighting system;
  (d) cyclones with dust recovery hopper;
  (e) heat recovery system

TUNNEL AND/OR DECK OVENS, electric, with OR without stand

NUT ROASTERS, programmable logic controlled, having ALL of the 
following:
  (a) pneumatic loading system with hopper AND dust collector;
  (b) centrifugal cyclone;
  (c) support frame;
  (d) electrical controls

COOLING TUNNEL MACHINES, CHOCOLATE, programmable logic 
controlled, having ALL of the following:
  (a) tunnel length NOT greater than 20 m and width NOT greater 
      than 2 m;
  (b) blowers AND evaporators;
  (c) conveyor;
  (d) electrical controls

GRILLS, clamshell, having ALL of the following:
  (a) two or more upper grill plates;
  (b) single lower plate;
  (c) touch screen operation;
  (d) USB interface

KETTLES, FOOD PREPARATION, electric, jacketed, with OR without 
ANY of the following:
  (a) electric tilting;
  (b) mixer;
  (c) hand shower;
  (d) whipping grid;
  (e) strainer plate;
  (f) measuring stick;
  (g) installation kit;
  (h) free standing floor kit

BLANCHERS, tunnel, water OR steam, having ALL of the following:
  (a) stainless steel conveyor;
  (b) water collection AND filtration system;
  (c) internal service passage with access doors

DEEP FRYERS, including ALL of the following:
  (a) cloth feeding table;
  (b) turn unit;
  (c) continuous conveyer fryer;
  (d) outfeed belt;
  (e) product tray

KETTLES, FOOD PREPARATION, electric, jacketed, including ALL of 
the following:
  (a) stepless mixing;
  (b) steam jacket;
  (c) touch panel programmable control;
  (d) electric tilting;
  (e) hand shower,
with OR without ANY of the following:
            (i) strainer plate;
           (ii) measuring stick;
          (iii) safety grid lid;
           (iv) mixing tool;
            (v) hand mixer;
           (vi) blender kit;
          (vii) free standing floor kit;
         (viii) installation kit

NUT ROASTERS, vertical, having ALL of the following:
  (a) feeding silo;
  (b) motor driven feeding rolls;
  (c) heating AND stabilisation levels;
  (d) buffer storage;
  (e) discharge screw;
  (f) heat exchanger;
  (g) ventilator;
  (h) cyclones with dust collectors;
  (i) fire extinguishing system;
  (j) electrical controls

CONFECTIONARY MAKING MACHINES, including ALL of the following:
  (a) mixing AND batching AND weighing machines;
  (b) ingredient dosers;
  (c) weigher AND filler;
  (d) water heat exchanger;
  (e) pumps;
  (f) control panels;
  (g) stirrers AND agitators;
  (h) pipes AND/OR ducts;
  (i) temperature AND pressure controls; 
  (j) batch cooker

DEEP FRYERS, having ALL the following:
  (a) cloth feeding table;
  (b) transfer AND/OR distribution unit;
  (c) continuous conveyer fryer;
  (d) steam lid

BAKING OVENS, programmable logic controlled, including ALL of 
the following:
  (a) refractory hearth plates; NOT greater than 20 mm in 
      thickness;
  (b) deck configuration NOT greater than 5; 
  (c) tray size 400 x 600 mm, with a tray capacity NOT greater
      than 6 per deck

MILK STEAMING MACHINES, including ALL of the following:
  (a) sensors;
  (b) drain tray;
  (c) drain tray cover;
  (d) drain box;
  (e) platform tilting block

OVENS, FOOD, double spiral, including ALL of the following:
  (a) cover with lift unit;
  (b) exhaust section;
  (c) circulation ventilators;
  (d) climate controller;
  (e) thermal fluid heating system;
  (f) steam supply unit;
  (g) conveyors,
with OR without smoking unit

VACUUM CYLINDER COOKERS, CONFECTIONERY, with one OR both of 
the following:
  (a) vacuum pump;
  (b) control cabinet

PANCAKE AND CRUMPET MAKING LINE, having ALL of the following:
  (a) ring AND plate cleaners; 
  (b) oiler;
  (c) burner system;
  (d) servo driven volumetric depositor;
  (e) 2 stage take off AND alignment system;
  (f) servo driven product turnover system

CRUMPET MAKING LINE, having ALL of the following:
  (a) servo controlled volumetric batter depositor;
  (b) product ring oiler;
  (c) plate AND ring cleaning system;
  (d) blown flame baking system;
  (e) combustion gas extraction system;
  (f) gas safety system;
  (g) 2 stage take off system

OVENS, CONVECTION AND STEAM, including BOTH of the following:
  (a) water connection having a rated pressure NOT less than
      149 kPa;
  (b) self-cleaning device

CHILLERS, air-cooled, having ALL of the following:
  (a) cooling capacity NOT less than 1 100 kW per cooler;
  (b) air flow rate per cooler NOT less than 70 M3/s;
  (c) water with ethylene glycol internal medium;
  (d) heat exchanger maximum working temperature NOT less than 
      33 degrees Celsius;
  (e) axial fan having a minimum rotating speed NOT less than 
      1 200 rpm

CABINETS, MEAL COOKING AND DELIVERY, wheeled, consisting of ALL 
of the following:
(a) dual air convection oven;
(b) static cooling refrigerator;
(c) touch screen controls,
with OR without plate warmer draw

HOT-PLATES, portable, electric

LIQUORICE PRODUCTION MACHINERY, including ANY of the 
following:
  (a) liquorice slurry kitchen;
  (b) viscotater cooking unit

HEATERS AND/OR COOKERS AND/OR EMULSIFIERS, FOOD PROCESSING, 
having ALL of the following:
  (a) control system;
  (b) temperature gauge;
  (c) pressure transmitter;
  (d) servo motor;
  (e) gear motor;
  (f) tapered feed screw;
  (g) steam regulation system;
  (h) steam pressure AND/OR distribution valves

FOAMERS OR STEAMERS, LIQUID, including BOTH of the following:
  (a) pitchers incorporating radio frequency identification 
      (RFID) tags;
  (b) installation kits consisting of hoses AND valves

RIPENING ROOMS, FRUIT, with OR without ANY of the following:
   (a) pallet racks;
   (b) lighting;
   (c) roller doors

DAIRY MILK EVAPORATORS, programmable logic controlled 
including BOTH of the following:
  (a) mechanical vapour recompression evaporator with OR without 
      fan including ALL of the following:
          (i) thermal vapour recompression units;
         (ii) pasteuriser;
        (iii) evaporative capacity exceeding 6 900 kg/hr;
         (iv) vacuum heat exchangers;
          (v) vapour separating vessels;
         (vi) clean in place station,
  (b) piping

SUGAR PREPARATION MACHINES, MARSHMALLOW PRODUCTION LINE,  
including ALL of the following:
  (a) dosing pumps;
  (b) feeders;
  (c) premixing tanks;
  (d) cooking vessels;
  (e) buffering tanks;
  (f) downstream pumps with pressure sensor

COOKING PRESS, FOOD, having ALL of the following functions:
  (a) infrared cooking;
  (b) microwave cooking;
  (c) contact plate cooking

CONFECTIONERY PRODUCTION LINE, including ALL of the following: 
  (a) stainless steel mixing tanks, with OR without insulation; 
  (b) sack supports;
  (c) water meters, with OR without spray balls;
  (d) water tempering units, having heating elements;
  (e) piping;
  (f) batch cookers, including EITHER of the following:
         (i) insulation;
        (ii) steam jackets,
  (g) stainless steel ingredient reservoirs, including EITHER 
      of the following: 
         (i) insulation;
        (ii) flow transmitters,
  (h) pumps;
  (i) butterfly valves;
  (j) metering valves;
  (k) tempering water circuits, including BOTH or the following:
         (i) vessels; 
        (ii) heat exchangers OR plates,
  (l) control panels

STERILISER, LIQUID FOOD AND/OR BEVERAGE having all of the 
following:
  (a) sterilisation temperature NOT greater than 150 degrees C;
  (b) feed module hopper tank;
  (c) direct steam injection module;  
  (d) deaeration module;
  (e) tubular heat exchanger

COOKING MACHINES, PRESURE AND/OR VACUUM COOKING, programmable 
logic controlled, including ALL of the following:
  (a) bowls, having BOTH of the following:
         (i) cooling jackets;
        (ii) steam heated jackets,
  (b) maximum internal working NOT greater than 1 bar;   
  (c) maximum vacuum pressure NOT greater than -990 mbar; 
  (d) maximum operating temperature NOT less than 124  
      degrees Celsius;    
  (e) vacuum pumps;
  (f) compressors;
  (g) dosing hopper;
  (h) knife AND/OR tool fixation;
  (i) scraper

STERILISERS, DICED FRUIT, including ALL of the following:
  (a) pumps;
  (b) flow meter;
  (c) ohmic heater;
  (d) cleaner;
  (e) aseptic tube cooler;
  (f) insulated aseptic holding pipes; 
  (g) pneumatic diversion valves

BLANCHERS, ASEPTIC DICED FRUIT, including ALL of the following:
  (a) infeed bar elevator;
  (b) blancher; 
  (c) vibrating separator

ROASTING MACHINES, COCOA BEANS

COFFEE BEAN ROASTING MACHINES, programmable logic controlled, 
including ANY one OR more of the following:
  (a) afterburner;
  (b) loading hoppers;
  (c) cooling tanks;
  (d) roasting drums
  (e) hot AND cold temperature air circuits;
  (f) heat generators;
  (g) chimneys;
  (h) catalytic converter

DEFROSTING MACHINES, programmable logic controlled, including 
ALL of the following:
  (a) humidification AND temperature controls;
  (b) atomizing water spray nozzles;
  (c) remote monitoring AND control;
  (d) product core AND surface probe controls;
  (e) refrigeration controls;
  (f) trolleys; 
  (g) ice breaker trays AND/OR baskets

FOOD FRYING SYSTEM, including ALL of the following:
  (a) frying machine, incorporating conveyors;
  (b) insulated hood;
  (c) vapour extraction flues;
  (d) pumps,
with OR without infeed AND/OR outfeed conveyors

COOKERS, SUGAR SYRUP, including holding tank

FOOD PROCESSING AND DISPENSING MACHINES, programmable logic 
controlled, including BOTH of the following:
  (a) bain-marie heating AND cooling;
  (b) mixer AND/OR stirrer

GRAIN AND/OR MALT ROASTING MACHINES, including ALL of the 
following:
  (a) filling socket;
  (b) rotating roasting drum;
  (c) media rack;
  (d) burner chamber;
  (e) outlet chute

STEAM PEELERS, VEGETABLE, having BOTH of the following;
  (a) maximum raw product throughput capacity NOT greater than 
      50 000 kg/h;
  (b) maximum steam pressure NOT greater than 20.4 bar

COFFEE MAKING MACHINES, ESPRESSO, having ANY of the following:
  (a) multiple boilers;
  (b) programmable logic control;
  (c) individual group temperature controls;
  (d) group head height EXCEEDING 15 cm from drip tray;
  (e) independent steam boiler

COOKING TUNNELS, FOOD MANUFACTURING, including BOTH of the 
following:
  (a) steam tunnel;
  (b) plastic belt conveyor

CHAFERS, having ANY of the following:
  (a) cover;
  (b) stand;
  (c) water pan AND/OR boiler pan

STEAMERS, HAY, including ALL of the following:
  (a) manifolds;
  (b) perforated spikes;
  (c) insulated boxes;
  (d) aluminium plates;
  (e) heating elements;
  (f) water capacity NOT greater than 8 litre

OVENS, CONVECTION AND/OR MICROWAVE, air impingement, stainless 
steel, programmable logic controlled, having a catalytic 
converter

COFFEE BEAN PROCESSING LINE, programmable logic controlled, 
having a roasting batch capacity NOT less than 300 kg

PANS, BRATT, stainless steel, gas and/or electric

PANS, BOILING, stainless steel, gas or electric

CONTAINERS, FOOD, stainless steel interior, insulated, heated, 
whether or not wheeled

PANCAKE MACHINES, counter top, programmable logic controlled

DISPENSERS, STEAM AND HOT WATER

ROOMS, FOOD PROCESSING, THAWING OR DEFROSTING

BATCH HOUSES, FOOD PROCESSING, SMOKING AND COOKING

OVENS, BAKERY, ROTARY RACK

OVENS, CONVECTION AND STEAM, having NOT less than 5 trays OR 
racks

FRYERS, DEEP, incorporating infra-red gas burners

HORIZONTAL COOKER AND/OR COOLER, tiltable vessel

OVENS, BAKING, plc, having NOT less than 3 but NOT greater than 
10 baking trays

MEAT STEAMERS, stainless steel

GRILLS, clamshell, electric, plc, having manual or electronically
 closing hot plates

DONUT MAKERS

TOASTERS, BREADROLL, comprising infrared elements and variable
 speed conveyor

HOLDING CABINETS, HEATED FOOD, 5.5amp, comprising BOTH of the
 following:
   (a) stainless steel exterior cabinet;
   (b) dual side pass through access

KETTLES, SOUP

COOKERS, RICE

ROASTERS, NUT, comprising BOTH of the following:
   (a) copper bowl;
   (b) agitator

STRIPPERS, steam, wallpaper

TEMPERING MACHINES, chocolate

VESSELS, reactor or storage, pressure, glass lined, cylindrical

MANTLES, heating, laboratory flask