| Tariff Classification | TCO Number | TCO description | Operative date | Decision date |
| 4009.31.90 | 1102990 |
WELDING HOSES, having ALL of the following:
(a) rubber inner layer;
(b) textile inner layer;
(c) rubber outer layer
| 19/01/2011 | 18/04/2011 |
| 4009.31.90 | 0702645 |
HOSES, ABRASIVE FLUID CONVEYING
| 28/02/2007 | 18/05/2007 |
| 4009.31.90 | 0619085 |
HOSE, RUBBER, reinforced with synthetic textile material
| 29/11/2006 | 02/03/2007 |
| 4009.31.90 | 0111127 |
HOSE, SAND AND SHOT BLAST, textile reinforced rubber, static
dissipating, having a minimum burst pressure of 3.0 MPa
| 01/01/2002 | 11/01/2002 |
| 4009.31.90 | 0107346 |
RUBBER HOSE, peristaltic, textile reinforced having ALL of the
following:
(a) maximum discharge pressure 16 bars;
(b) maximum line pressure 48 bars;
(c) outer surface having spiral wound synthetic abrasion resistant
finish, NOT further worked;
(d) operating temperature from -20 degrees C to 120 degrees C;
(e) natural and nitrile butyl rubber hoses having a shore hardness
of 53 +/- 5 shore;
(f) ethylene propylene rubber (EPDM) hose having a shore hardness
of 66 +/- 5 shore;
(g) internal and external diameter as follows:
(i) 10 +/- 0.5 mm and 32 +/- 0.7 mm;
(ii) 15 +/- 0.5 mm and 37 +/- 0.7 mm;
(iii) 25 +/- 0.5 mm and 55 +/- 0.7 mm;
(iv) 32 +/- 0.5 mm and 62 +/- 0.7 mm;
(v) 40 +/- 0.5 mm and 67 +/- 0.7 mm;
(vi) 50 +/- 0.5 mm and 81 +/- 1.2 mm;
(vii) 65 +/- 0.5 mm and 101 +/- 1.2 mm;
(viii) 80 +/- 0.5 mm and 123 +/- 1.2 mm;
(ix) 100 +/- 0.5 mm and 144 +/- 1.2 mm;
(x) 125 +/- 0.5 mm and 170 +/- 1.2 mm
| 01/01/2002 | 08/01/2002 |
| 4009.31.90 | 0107615 |
HOSE, double carcass of vulcanised rubber, reinforced with woven
high tenacity polyester fibre material, having ALL of the following:
(a) ID NOT less than 50 mm;
(b) lengths NOT less than 200 m;
(c) capable of withstanding a peak maximum working pressure of
30 bar (440 PSI) or greater;
(d) maximum continuous working pressure of 21 bar (300 PSI) or
greater;
(e) non-bursting pressure of 50 bar (720 PSI) or greater;
(f) breaking load safety factor > 3;
(g) diametric swell under maximum pressure 8-9%;
(h) average elongation 2%;
(i) empty weight NOT less than 1.35 kg/m;
(j) full weight NOT less than 6.11 kg/m;
(k) maximum operating temperature 50 degrees C (pH-9);
(l) minimum sevice load (200 m hose full of water + pump)
1.6 tonne
| 01/01/2002 | 08/01/2002 |
| 4009.31.90 | 0107348 |
HOSE, moulded, re-inforced synthetic cord having ALL of the
following specifications:
(a) covered by EITHER of the following synthetic materials;
(i) ethylene propylene terpolymer;
(ii) carboxylate nitrate butaidene;
(b) burst pressure of NOT less than 800 kPa;
(c) internal diameter NOT greater than 51 mm
(d) capable of operating at a temperature of a minimum of 20
degrees C and a maximum of 82 degrees C
| 01/01/2002 | 08/01/2002 |
| 4009.31.90 | 0107347 |
RUBBER HOSE, peristaltic, reinforced with braided nylon, having
ALL of the following:
(a) maximum working discharge pressure of 15 bars;
(b) maximum line pressure of 15 bars;
(c) maximum vacuum capability without deformation 5 kPa.a;
(d) hose static burst pressure range of 45 bar to 125 bar, both
inclusive;
(e) outer surface machined to a tolerance of 0.25 mm, completely
smooth with no spiral wound synthetic tape used;
(f) operating temperature of -20 degrees C to 85 degrees C;
(g) (i) natural, (NR), buna nitrile rubber, (NBR), or high buna
nitrile, (NBRX) body having a shore hardness of
57 + or - 4 shore; OR
(ii) ethylene propylene rubber, (EPDM) body having a shore
hardness of 59 + or - 4 shore; OR
(iii) hypalon rubber (HPN) body having shore hardness of
59 + or - 4 shore;
(h) hose internal diameters, wall thicknesses and lengths
respectively as follows;
(i) 10.5 mm (+ or - 0.5 mm), 10.5 mm (+ or - 0.2 mm) and
510 mm (+ or - 5 mm);
(ii) 15.5 mm (+ or - 0.5 mm), 10.5 mm (+ or - 0.2 mm) and
755 mm (+ or - 5 mm);
(iii) 26 mm (+ or - 1.0 mm), 14.1 mm (+ or - 0.2 mm) and
1005 mm (+ or - 10 mm);
(iv) 33.1 mm ( + or - 1.0 mm), 14.5 mm (+ or - 0.2 mm) and
1252 mm (+ or - 10 mm);
(v) 41 mm (+ or - 1.0 mm), 13.2 mm (+ or - 0.2 mm) and
1490 mm (+ or - 10 mm);
(vi) 51.5 mm (+ or - 1.5 mm), 15.0 mm (+ or - 0.2 mm) and
1820 mm (+ or - 10 mm);
(vii) 66.5 mm (+ or - 1.5 mm), 17.1 mm (+ or - 0.2 mm) and
2335 mm (+ or - 10 mm);
(viii) 81.5 mm (+ or - 1.5 mm), 21.0 mm (+ or - 0.25 mm) and
2780 mm, (+ or - 20 mm);
(ix) 101.5 mm (+ or - 1.5 mm), 22.0 mm (+ or - 0.25 mm) and
3275 mm (+ or - 25 mm)
| 01/01/2002 | 08/01/2002 |
| 4009.31.90 | 107615 |
HOSE, double carcass of vulcanised rubber, reinforced with woven
high tenacity polyester fibre material, having ALL of the following:
(a) ID NOT less than 50 mm;
(b) lengths NOT less than 200 m;
(c) capable of withstanding a peak maximum working pressure of
30 bar (440 PSI) or greater;
(d) maximum continuous working pressure of 21 bar (300 PSI) or
greater;
(e) non-bursting pressure of 50 bar (720 PSI) or greater;
(f) breaking load safety factor > 3;
(g) diametric swell under maximum pressure 8-9%;
(h) average elongation 2%;
(i) empty weight NOT less than 1.35 kg/m;
(j) full weight NOT less than 6.11 kg/m;
(k) maximum operating temperature 50 degrees C (pH-9);
(l) minimum sevice load (200 m hose full of water + pump)
1.6 tonne
| 01/01/2002 | 08/01/2002 |
| 4009.31.90 | 107348 |
HOSE, moulded, re-inforced synthetic cord having ALL of the
following specifications:
(a) covered by EITHER of the following synthetic materials;
(i) ethylene propylene terpolymer;
(ii) carboxylate nitrate butaidene;
(b) burst pressure of NOT less than 800 kPa;
(c) internal diameter NOT greater than 51 mm
(d) capable of operating at a temperature of a minimum of 20
degrees C and a maximum of 82 degrees C
| 01/01/2002 | 08/01/2002 |
