Tariff Concession Orders

LOW DENSITY POLYETHYLENE (LDPE) FILM, in rolls, having ALL of 
the following:
  (a) thickness NOT less than 6.5 microns and NOT greater than  
      10.5 microns;
  (b) film width NOT greater than 440 mm;
  (c) length NOT less than 400 m and NOT greater than 3 500 m;
  (d) film weight NOT less than 1.9 kg and NOT greater 
      than 13.8 kg;
  (e) laps on each edge;
  (f) pre-stretched

FILM, linear low density polyethylene, having BOTH of the 
following:
  (a)  thickness NOT less than 250 micron;
  (b)  width NOT less than 3 m

DROP SHEETS, polyethylene

FILM, low density polyethylene, embossed AND siliconised

LINING MATERIALS, polyethylene, high density, acid resistant, 
being
 ANY of the following forms:
   (a) wall screed guides;
   (b) screed strips;
   (c) pre-fabricated forms;
   (d) h-zip strips

FILM, MOLECULAR BINDING, heat induced, ethylene vinyl acetate

FILM, polyethylene, in rolls, 3 layer co-extruded, UV 
stabilised, having BOTH of the following:
  (a) width NOT less than 4 m and NOT greater than 13 m;
  (b) thickness not less than 100 micrometre and not greater than
      250 micrometre

SHEETS, PROTECTIVE STERILE FIELD, polyethylene

FILM, polyethylene, in rolls, having a width NOT less 
than 10 000 mm

FILM, POLYETHYLENE, in rolls in serrated edged packages, having 
ALL of the following:
  (a) thickness NOT less than 9 microns and NOT greater than 20
      microns;
  (b) width NOT greater than 45 cm;
  (c) length NOT greater than 600 m

GEOMEMBRANES, ethylene vinyl acetate, in rolls, having BOTH the 
following:
  (a) width NOT less than than 6.5 metres;
  (b) thickness NOT less than 0.50 mm and NOT greater than 3.0 mm

FILM, POLYETHYLENE, in rolls in serrated edged packages, having 
ALL of the following:
  (a) thickness NOT less than 9 microns and NOT greater than 12
      microns;
  (b) width NOT greater than 38 cm;
  (c) length NOT greater than 150 m

FILM, POLYETHYLENE, in rolls in serrated edged packages, having 
ALL of the following:
  (a) thickness NOT less than 9 microns and NOT greater than 12 
      microns;
  (b) width NOT greater than 33 cm;
  (c) length NOT greater than 30 m

SHEETS, PROTECTIVE, STERILE, polyethylene, having ALL of the 
following:
  (a) width NOT greater than 150 cm;
  (b) length NOT greater than 220 cm;
  (c) thickness NOT greater than 45 micron

SHEETS, HDPE, having ALL the following:
   (a) fully pigmented with calcium carbonate;
   (b) having a permeability to water of less than 0.5 g/m DIN 53122
       at 23 degrees C and 85% relative atmospheric humidity

SHEETS, polyethylene, high density, pervious, moulded, sintered

POLYETHYLENE SHEET, cast low density, embossed and coloured,
 whether or not printed

POLYETHYLENE FILM, linear low density, uncoated, unpigmented,
 unprinted, NOT corona discharge treated, conforming to ALL of the
 following specifications:
   (a) width 200 - 750 mm;
   (b) length NOT exceeding 1 000 m or an OD NOT exceeding 265 mm;
   (c) thickness 15 microns OR 20 microns;
   (d) a shrinkage factor of NOT less than 70% at 140 degrees C in
       BOTH machine and transverse directions;
   (e) tensile strength not less than 530 kg/cm2 in both machine
       and transverse directions
   (f) impact strength NOT less than 8.5 kg/cm2 in BOTH machine and
       transverse directions

SHEETS, NON CELLULAR, high density polyethylene (HDPE), compressed
 heat laminated, multilayered, having ALL of the following:
   (a) minimum physical properties as follows:
         (i) thickness of 19 mm;
        (ii) density of 0.98 g/cu cm;
       (iii) tensile strength 3 900 psi;
   (b) non permeable;
   (c) UV stabilised

SYNTHETIC PAPER, biaxially oriented polyethylene, clay coated

POLYETHYLENE FILM, high density oriented and cross laminated,
 having two or more layers of film in which the molecular
 orientation runs at 90 degrees to one another, whether or not clay
 coated or corona discharge treated

POLYETHYLENE FILM, 5 layer, co-extruded, thermoformable, low
 density, having BOTH of the following:
   (a) width NOT exceeding 2 100 mm;
   (b) thickness NOT exceeding 100 microns;

PROTECTIVE SHEETS, polyethylene, embossed, non cellular, having BOTH
 of the following:
   (a) a width NOT exceeding 2.6 m;
   (b) a length NOT exceeding 3.6 m

SHEETING, high density polyethylene, having BOTH of the following:
   (a) specific gravity NOT less than 0.94 at 20 degrees Celsius;
   (b) thickness NOT less than 7 mm

SEALING STRIP, ASEPTIC JUICE AND DAIRY PACKAGE, multi layer, heat
 sealing

POLYETHYLENE WRAP SHEETING, imported in roll form of a width
 exceeding 4 720 mm

SHRINK FILM, POLYOLEFIN, multi-layer, having ALL of the
 following:
   (a) single wound OR centre folded;
   (b) thickness NOT less than 11 microns and NOT greater
       than 35 microns;
   (c) yield (m2/kg) NOT less than 43.5 m2/kg and NOT greater
       than 100 m2/kg;
   (d) shrinkage NOT less than 50% and NOT greater than 75% at
       120 degrees C;
   (e) haze of less than 4%

POLYETHYLENE FILM, linear low density, breathable, calcium carbonate

MEMBRANE, low density polyethylene, in rolls, having ALL of the 
following:
  (a) width NOT less than 2 metres;
  (b) length NOT less than 10 metres;
  (c) thickness NOT less than 2 mm

LOW DENSITY POLYETHYLENE (LDPE) FILM, embossed

SHEETING, IN ROLLS, having ALL of the following:
  (a) base of rapier woven high density polyethylene fabric
      having BOTH of the following;
       (i)  yarn NOT less than 1 100 decitex;
       (ii) NOT less than 5 yarns in both warp and weft 
            directions per square centimetre; 
  (b) coated on both sides with low density polyethylene;
  (c) width NOT less than 2 600 mm;
  (d) weight NOT less than 170 grams per square metre

FILM, plastic, multi-layered, having ALL of the following:
  (a) polyethylene OR ethylene-vinyl acetate co-polymer
      core layer;
  (b) polyethylene outer layers;
  (c) combined multi-layered film thickness NOT less than 20
      micron and NOT greater than 60 micron;
  (d) circumference capacity NOT less than 1 600 mm and NOT
      greater than 6 800 mm;
  (e) maximum stretching capacity NOT less than 10% and NOT
      greater than 120%

MEMBRANE SHEETS, high density polyethylene, in rolls, having 
ALL of the following: 
  (a) membrane density NOT less than 0.94 grams per cubic 
      centimetre;
  (b) roll width NOT less than 7 metres;
  (c) roll length NOT greater than 280 metres;
  (d) membrane thickness NOT less than 0.75 mm and NOT
      greater than 4 mm;
  (e) elongation at break NOT less than 350 per cent;
  (f) tensile strength at break NOT less than 17 newtons
      per square millimetre;
  (g) a patterned AND structured surface on at least one side

MEMBRANE SHEETS, high density polyethylene, in rolls, having 
ALL of the following: 
  (a) membrane density NOT less than 0.94 grams per cubic 
      centimetre;
  (b) roll width NOT less than 7 metres;
  (c) roll length NOT greater than 280 metres;
  (d) membrane thickness NOT less than 0.75 mm and NOT
      greater than 4 mm;
  (e) smooth AND creaseless surface on both sides

MEMBRANE SHEETS, linear low density polyethylene, in rolls, 
having ALL of the following: 
  (a) membrane density NOT greater than 0.94 grams per cubic 
      centimetre;
  (b) roll width NOT less than 7 metres;
  (c) roll length NOT greater than 280 metres;
  (d) membrane thickness NOT less than 0.75 mm and NOT
      greater than 4 mm;
  (e) elongation at break NOT less than 350 per cent;
  (f) tensile strength at break NOT less than 17 newtons
      per square millimetre;
  (g) patterned AND structured surface on at least one side

MEMBRANE SHEETS, linear low density polyethylene, in rolls, 
having ALL of the following: 
  (a) membrane density NOT greater than 0.94 grams per cubic 
      centimetre;
  (b) roll width NOT less than 7 metres;
  (c) roll length NOT greater than 280 metres;
  (d) membrane thickness NOT less than 0.75 mm and NOT
      greater than 4 mm;
  (e) smooth AND creaseless surface on both sides

GEOMEMBRANES, high density polyethylene, in rolls, having 
ALL of the following:
  (a) width NOT less than 7 m;
  (b) length NOT less than 50 m;
  (c) thickness NOT less than 0.75 mm and NOT greater than 3.0 mm

GEOMEMBRANES, low density polyethylene, in rolls, having 
ALL of the following:
  (a) width NOT less than 7 m;
  (b) length NOT less than 50 m;
  (c) thickness NOT less than 0.75 mm and NOT greater than 3.0 mm

FILM, plastic, 9 layered co-extruded, having a thickness NOT 
less than 90 um and NOT greater than 150 um

FILM, LDPE AND EVA, in rolls, UV stabilised, having BOTH of the 
following:
  (a) thickness NOT greater than 200 micron;
  (b)  width NOT less than 5.5 m and NOT greater than 14 m

SHEETS, LAMINATED, polyethylene having ALL of the following:
  (a) density NOT less than 900kg/m3;
  (b) one black and NOT less than one coloured layer;
  (c) thickness NOT less than 1.5 mm and NOT greater than 3.5 mm

POLYETHYLENE, in pressed sheets, ultra-high molecular weight,
having NOT less than 9 million molecular weight

POLYETHYLENE SHEET, being ANY of the following:
  (a) high molecular weight polyethylene (HMWPE) sheet having
      a ball indentation hardness NOT less than 50 newtons 
      per square millimetre;
  (b) ultra high molecular weight polyethylene (UHMWPE) sheet
      having BOTH of the following:
           (i) notched impact strength NOT less than 140 kJ
               per square metre;
          (ii) elongation at break NOT less than 350 per cent,
  (c) ultra high molecular weight polyethylene (UHMWPE) sheet,   
      having ALL of the following:
           (i) density NOT less than 0.93 grams per cubic
               centimetre;
          (ii) notched impact strength NOT less than 150 kJ
               per square metre;
         (iii) elongation at break NOT less than 250 per cent;
          (iv) tensile strength at yield NOT less than 17
               newtons per square millimetre

POLYETHYLENE SHEETS, ultra-high molecular weight, 
having ALL of the following:
  (a) density NOT less than 0.93 grams per cubic cm;
  (b) notched impact strength NOT less than 100 kJ per sq m;
  (c) elongation at break NOT less than 50 per cent;
  (d) tensile strength at yield NOT less than 17 Newtons;
  (e) length NOT less than 1 m;
  (f) width NOT less than 1 m and NOT greater than 4 m;
  (g) thickness NOT less than 3 mm and NOT greater than
      70 mm

FILMS, FOOD PACKAGING, having a thickness NOT less than 0.085 mm 
and NOT greater than 0.15 mm, being EITHER of the following 
compositions:
  (a) polyethylene AND ethylene vinyl alcohol; 
  (b) polyethylene AND polyamide AND polyethylene terephthalate

SHRINK FILM, polyolefin, low-density polyethylene, having ALL of 
the following:
  (a) single wound;
  (b) thickness NOT greater than 12 microns;
  (c) shrinkage NOT less than 70% at 120 degrees Celsius

STRETCH FILM, co-extruded polyolefin, having BOTH of the 
following:
  (a) repeating laser micro perforations of NOT greater than 
      52 micrometres;
  (b) complying with Regulation (EC) 1935/2004

POLYETHYLENE FILMS, embossed AND/OR coloured, in rolls, having 
BOTH of the following:
  (a) roll width NOT less than 130 mm and NOT greater than 
      700 mm;
  (b) basis weight NOT less than 15 gsm and NOT greater than 
      22 gsm