Tariff Concession Orders

PARTS,HAND TOOL, steel, being ANY of the following:
  (a) mattock heads;
  (b) pick heads;
  (c) hoe heads;
  (d) rake heads

MATTOCKS OR PICKS OR HOES OR RAKES

MATCHETS (machetes), having BOTH of the following:
   (a) blade length NOT less than 450 mm;
   (b) blade thickness NOT less than 3 mm

KNIVES, cane cutters"

AXES, firemen"s

AXES OR HATCHETS

SHEARS, foot-rot

SHEARS, grass, having a blade adjustment allowing the blades to
 swivel to three cutting planes

SHEARS, POULTRY

PRUNING SETS, garden, consisting of secateurs and pruning saw

SECATEURS OR SHEARS, one handed

TOOL SETS, comprising ALL of the following:
  (a) trowels;
  (b) secateurs;
  (c) forks

SECATEURS OR PRUNERS OR SHEARS, ONE HANDED, bypass design

SECATEURS, BY-PASS

SHEARS, HEDGE, two handed

SETS, GARDEN HAND TOOL, consisting of ALL of the following:
  (a) pruning shear;
  (b) lopping shear;
  (c) hedge shear

SHEARS OR LOPPERS, two handed

PRUNING SHEARS, TWO HANDED, anvil design

SHEARS, sheep, but NOT including footrot shears

SCYTHES

SICKLES

TOOL SETS, garden, NOT exceeding 900 grams, comprising at least
 ANY three of the following:
   (a) trowel (spade);
   (b) cultivator;
   (c) fork;
   (d) transplanter

TOOLS, garden, individual weight NOT exceeding 300 grams, being
 ANY of the following:
   (a) trowel (spade);
   (b) cultivator;
   (c) transplanter

GOLF DIVOT REPAIRERS

FORKS, garden, weight NOT exceeding 210 grams

HAND TOOLS, AGRICULTURE OR HORTICULTURE OR FORESTRY, being ANY of
 the following:
   (a) bulb planters and/OR trowels;
   (b) potting trowels;
   (c) cultivators;
   (d) lawn aerators;
   (e) edgers;
   (f) log splitters;
   (g) single OR double pronged hoes;
   (h) timber wedges;
   (i) post hole diggers;
   (j) potting scoop;
   (k) top soil spreader;
   (l) weeders;
   (m) weeders and/OR cultivators;
   (n) cultivators and/OR tillers;
   (o) rakes and/OR hoes;
   (p) gutter cleaners

BOW SAWS

SAWS, but NOT including ANY of the following:
   (a) hacksaws;
   (b) bow saws;
   (c) keyhole saws and the like

SAWS, permanently combined with a mitre joint assembly appliance

HAND SAWS

BANDSAW BLADING, in coil, unjoined, being of the hardened edge
 type, having the following specifications:
   (a) blade width of 31-41 mm (inclusive), a gauge/thickness from
       1.07 mm to 1.27 mm (inclusive) and having a vari-tooth pitch
       from 1.4 to 2.5 t.p.i;
   (b) blade width of 50-54 mm (inclusive), having a gauge/thickness
       from 1.27 mm to 1.60 mm and having a vari-tooth pitch from
       1.4 to 2.5 t.p.i

BLADES OR BLADING, BI-METAL, in coils, unjoined (welded or brazed)
 in widths from 1.5 mm to 100 mm (inclusive) being ANY of the
 following:
   (a) hardened tooth;
   (b) hardened edge;
   (c) welded edge

BAND SAW BLADING, tungsten carbide grit edge

BANDSAW BLADES, in coils, welded, having ALL of the following:
  (a) depth NOT less than 12.5 mm and NOT greater than 25 mm;
  (b) gauge OR thickness NOT less than 0.40 mm and NOT greater
      than 0.80 mm; 
  (c) NOT less than 3 and NOT greater than 10 teeth per inch;
  (d) with OR without tooth pitch NOT being greater than 10 mm

BANDSAW BLADING, in coils, NOT welded OR brazed, in widths NOT 
less than 1.5 mm and NOT greater than 80 mm, being ANY of the 
following:
  (a) hardened tooth;
  (b) hardened edge;
  (c) grit edge

TOOLS, key cutting machine

BLADES, CIRCULAR, STEEL STRIP SLITTING LINE

BLADES, CIRCULAR, PAPER LOG SAW, being alloy steel containing 
chromium AND molybdenum AND vanadium

BLADES, CIRCULAR SAW, high speed steel, having ALL of the 
following:
  (a) blade diameter NOT less than 40 mm;
  (b) blade thickness NOT less than 1 mm;
  (c) blade centre hole diameter NOT less than 20 mm

BLADES, SAW, having ALL of the following:
 (a) cutting teeth per blade NOT less than 32; 
 (b) blade diameter NOT less than 40 mm;
 (c) blade thickness NOT less than 1.5 mm;
 (d) blade centre hole diameter NOT less than 40 mm

BLADES, CIRCULAR SAW, titanium cobalt carbide tipped

BLADES, jigsaw or reciprocating saw, for power operated hand
 tools

BLADES, power, hacksaw,  having a length of 650 mm or greater

BLADES, hacksaw, tungsten carbide grit edge

SAW BLADES, straight

BLADES, bow saw

BLADES, jigsaw or reciprocating saw, for power operated hand
 tools

BLADES, fret saw

BLADES, coping saw

BLADES, holesaw, carbide tipped

HOLESAWS, tungsten carbide grit edge

BLADES, HOLE SAW

RASPS, comprising a handle or holder and an interchangeable
 punched sheet metal blade whereby the material being worked can
 pass through holes in the blade

FILES, milled tooth, having teeth cut from a flat bar by a milling
 operation (whether or not subsequently heated and curved in
 section) and having the teeth NOT higher than the uncut portion
 of the bar

REAMERS, gas cutter or welder tip

SHARPENERS, steel edged snow ski

FILES, precision, including needle files, having numerical cuts
 (character of teeth) of 000, 00, 0, 1, 2, 3, 4, 5, 6, 7 or 8

FILES OR RASPS

PLIERS/PINCERS, cable or wire stripping

TWEEZERS

PLIERS, multiple slip joint, but NOT including pliers having a
 length of 125 mm or greater but NOT exceeding 400 mm
   For the purposes of TC 8901857 plier type and dimension are
   as described in International Standard ISO 5742

PLIERS, being ANY of the following types as described in
 International Standard ISO 5742:
   (a) flat nose;
   (b) round nose;
   (c) circlip, external or internal;
   (d) slip joint (NOT being multiple slip joint);
   (e) gaspipe;
   (f) fencing tool (NOT being button plier fence tool)

TOOLS, hand, non-sparking, composed wholly (except for handles,
 if any) of beryllium copper

PLIERS, spring band loaded, self-opening, having a weight NOT
 exceeding 35 g

PLIERS, retaining ring, reverse action

PLIERS, engineers" (combination) or linesmen"s, but NOT including
 pliers having a length of 140 mm or greater but NOT exceeding
 245 mm
   For the purposes of TC 8635229 plier type and dimension are
   as described in International Standard ISO 5742

PLIERS, lever assisted or toggle lever assisted
   For the purposes of TC 8634426, lever assisted and toggle
   lever assisted are as described in International Standard
   ISO 5742

PLIERS OR WRENCHES, toggle action, having BOTH of the following:
   (a) locking jaw mechanism;
   (b) jaw release mechanism

PLIERS, safety wire twisting, having a spiral wire twisting
 mechanism

NIPPERS, oblique cutting, but NOT including nippers having a
 length of 120 mm or greater
   For the purposes of TC 8633996, nipper type and dimension are
   as described in International Standard ISO 5742

PLIERS, snipe nose, tip cutting, having cutting surfaces located
 towards the tip of the jaw

PLIERS, snipe nose, NOT equipped with a cutting edge AND having
 plain jaws as described in International Standard ISO 5742

PINCERS, carpenters" or construction workers", as described in
 International Standard ISO 5742

NIPPERS, end cutting, but NOT including nippers having a length
 of 140 mm or greater but NOT exceeding 230 mm
   For the purposes of TC 8632340 nipper type and dimension are
   as described in International Standard ISO 5742

NIPPERS, diagonal cutting, but NOT including nippers having a
 length of 120 mm or greater but NOT exceeding 230 mm
   For the purposes of TC 8632339 nipper type and dimension are
   as described in International Standard ISO 5742

PLIERS, snipe nose, whether or not equipped with side cutter,
 but NOT including pliers having a length of 110 mm or greater
 but NOT exceeding 230 mm
 For the purposes of TC 8632338 plier type and dimension are as
 described in International Standard ISO 5742

TOOLS, crimping, but NOT including crimping tools put up in packs
 containing electrical connectors

PULLERS, nail, lever operated

NIPPERS, ceramic tile

PLIERS, spring loaded with insulated handles, being ANY of the
 following:
   (a) needle nosed pliers, length NOT exceeding 153 mm;
   (b) long nose pliers, length NOT exceeding 135 mm;
   (c) bent nose pliers, length NOT exceeding 125 mm;
   (d) end nippers, length NOT exceeding 115 mm;
   (e) flat nose pliers, length NOT exceeding 125 mm;
   (f) round nose pliers, length NOT exceeding 100 mm;
   (g) combination pliers, length NOT exceeding 165 mm;

PLIERS OR CUTTERS, insulated, complying with IEC 900 standard,
 tested to 10 000 V

NIPPERS, diagonal cutting, carbon steel, having a length of 150 mm

PLIERS, long nose, carbon steel, having a length of 150 mm

PLIERS, being one OR more of ANY of the following: 
  (a) needle nose combination pliers;
  (b) high leverage diagonal cutters;
  (c) long reach needle nose pliers having transverse
      profiles, with OR without curved tips

PLIERS, being one OR more of ANY of the following: 
  (a) combination pliers;
  (b) snipe nose side cutting pliers;
  (c) diagonal cutter;
  (d) high leverage diagonal cutter;
  (e) hightech water pump pliers;
  (f) ear clamp pliers;
  (g) electrical installation pliers;
  (h) farrier pincers;
  (i) glass breaking pincers;
  (j) mechanics pliers;
  (k) spring hose clamp pliers;

PLIERS, being ANY of the following:
  (a) aviation slip pliers;
  (b) bent nose pliers;
  (c) combination pliers, length NOT less than 210 mm;
  (d) cutting pliers;
  (e) end nipper pliers;
  (f) groove joint pliers;
  (g) linesman pliers, length NOT less than 210 mm;
  (h) lock grip pliers;
  (i) long nose pliers;
  (j) long reach pliers;
  (k) round nose pliers;
  (l) slip joint pliers;
  (m) snap ring pliers;
  (n) straight nose pliers;
  (o) welding clamp pliers;
  (p) wire stripper pliers

KITS, TENSIONING AND JOINING, FENCE AND/OR TRELLIS WIRE, 
comprising BOTH of the following:
  (a) wire tensioning and joining tool;
  (b) wire gripping connectors

PULLERS AND/OR EXTRACTORS, HAND TOOL

PLIERS, being EITHER of the following:
 (a) multiple slip joint;
 (b) pliers NOT exceeding 170 mm in length

NIBBLERS, sheet metal

CUTTERS, wire, shear action

NIPPERS, diagonal, spring loaded with insulated handles, length NOT
 exceeding 125 mm

CUTTERS, pipe or tube, but NOT including pipe cutters capable
 of cutting galvanised or steel pipe within the range 12 mm to
 50 mm outside diameter (both inclusive)

CUTTERS, metal cable, cutting capacity 8.7 mm or greater

DEHEADERS, steel drum

CUTTERS, cable, capable of cutting metal cable having a dia of
 8.7 mm or greater

PUNCHES, single hole, hand operated, stationery

PUNCHES, sheet metal, hand held key operated

PUNCHES, leather, but NOT including round hollow punches having
 a dia in the range of 1.5 mm to 12.7 mm (both inclusive)

CUTTERS, pipe, adjustable, being EITHER of the following types:
   (a) hinged, having a cutting capacity of 33 mm or greater;
   (b) rotary, having a cutting capacity of 140 mm or greater

BOLT OR PIPE OR TUBE CUTTERS

KEYS, torx recess type

TOOLS, hand, non-sparking, composed wholly (except for handles,
 if any) of beryllium copper

SPANNERS OR WRENCHES, ratcheting box (ring) type, having hexagonal
 or bi-hexagonal ratcheting box (ring) type openings at both ends,
 but NOT including spanners or wrenches put up in packs with goods
 OTHER THAN ratcheting box (ring) type spanners or wrenches

SPANNERS OR WRENCHES, being ANY of the types listed in TABLE A,
 but NOT including ANY of the goods listed in TABLE B
                               TABLE A
   (a) ring;
   (b) combination (ring and open end);
   (c) flexible head;
   (d) box wrench
                               TABLE B
   (a) spanners or wrenches put up in packs with goods OTHER THAN
       those listed in TABLE A;
   (b) spanners or wrenches or packs containing spanners or
       wrenches having one or both ends in ANY of the following
       sizes:
         (i) SAE or AF : 7/32 in. to 1 7/8 in. (both inclusive),
                         2 in. to 2 1/4 in. (both inclusive),
                         2 3/8 in., 2 1/2 in., 2 5/8 in.,
                         2 3/4 in., 2 15/16 in. or 3 1/8 in.;
        (ii) Metric    : 4 mm to 28 mm (both inclusive),
                         30 mm, 32 mm, 36 mm, 38 mm, 41 mm, 46 mm,
                         50 mm or 55 mm;
       (iii) Whitworth : 1/8 in. to 3/4 in. (both inclusive),
                         7/8 in., 1 in. or 1 1/8 in.;
        (iv) BS        : 3/16 in. to 3/4 in. (both inclusive),
                         7/8 in., 1 in., 1 1/8 in. or 1 1/4 in.

SPANNERS OR WRENCHES, open end type, but NOT including ANY of the
 following:
   (a) spanners or wrenches put up in packs with goods OTHER THAN
       open end type spanners or wrenches;
   (b) spanners or wrenches or packs containing open end type
       spanners or wrenches having one or both ends in ANY of the
       following sizes:
         (i) SAE or AF : 7/32 in. to 1 5/8 in. (both inclusive);
        (ii) Metric    : 4 mm to 27 mm (both inclusive), 30 mm,
                         32 mm or 36 mm;
       (iii) Whitworth : 1/8 in. to 3/4 in. (both inclusive),
                         7/8 in. or 1 in.;
        (iv) BS        : 3/16 in. to 3/4 in. (both inclusive),
                         7/8 in., 1 in. or 1 1/8 in.

SPANNERS OR WRENCHES, half moon ring, but NOT including ANY of the
 following:
   (a) spanners or wrenches put up in packs with goods OTHER THAN
       half moon ring spanners or wrenches;
   (b) spanners or wrenches or packs containing spanners or
       wrenches, having an opening at one or both ends in ANY of
       the following sizes:
         (i) SAE or AF : 1/2 in. to 5/8 in. (both inclusive);
        (ii) Metric    : 10 mm to 13 mm (both inclusive);
       (iii) Whitworth : 1/4 in. or 5/16 in.;
        (iv) BS        : 5/16 in. or 3/8 in.

SPANNERS OR WRENCHES, podger, construction or structural, but NOT
 including spanners or wrenches put up in packs with goods OTHER
 THAN podger spanners or wrenches

SPANNERS, tubular, double ended, but NOT including ANY of the
 following:
   (a) spanners put up in packs with goods OTHER THAN tubular
       spanners;
   (b) spanners or packs containing spanners, having an opening
       at one or both ends in ANY of the following sizes:
         (i) Whitworth : 3/16 in. to 5/8 in. (both inclusive);
        (ii) Metric    : 8 mm to 19 mm (both inclusive);
       (iii) SAE       : 5/16 in. to 1 1/8 in. (both inclusive)

SPANNERS OR WRENCHES, flare nut, including combination type, but
 NOT including ANY of the following:
   (a) spanners or wrenches put up in packs containing goods OTHER
       THAN flare nut spanners or wrenches including combination
       type;
   (b) spanners or wrenches having an opening at one or both ends
       in the following sizes:
         (i) SAE or AF : 3/8 in. to 3/4 in. (both inclusive),
             7/8 in., 1 in. or 1 1/8 in.;
        (ii) Metric    : 9 mm to 15 mm (both inclusive), or 17 mm

SPANNERS OR WRENCHES, hook or pin type, but NOT including such
 spanners or wrenches put up in packs containing goods OTHER THAN
 such spanners or wrenches

SPANNERS OR WRENCHES, crowfoot, of the flare nut or open end
 type, but NOT including spanners or wrenches put up in packs
 with goods OTHER THAN crowfoot spanners or wrenches of the flare
 nut or open end type

SPANNERS OR WRENCHES, slogging, incorporating a striking face
 for hammer tightening, but NOT including such spanners or wrenches
 put up in packs with goods OTHER THAN such spanners or wrenches

KEYS, allen or hexagon, dia exceeding 12 mm

SPANNERS, drop forged

TORQUE WRENCHES, dial indicating, having ANY of the following head
 attachments:
   (a) fixed square drive;
   (b) ratchet square drive

NUTDRIVERS, SAE or AF, in ANY of the following sizes:
   (a) 3/16" (5 mm);
   (b) 1/4" (6 mm);
   (c) 5/16" (8 mm);
   (d) 11/32" (9 mm);
   (e) 3/8" (10 mm);
   (f) 7/16" (11 mm);
   (g) 1/2" (13 mm)

SPANNERS OR WRENCHES, insulated, complying with IEC 900 standard,
 tested to 10 000 V

WRENCHES, torque, hexagon, in the following diameter sizes:
 0.71 mm;
 0.89 mm;
 1.27 mm;
 1.50 mm;
 2.00 mm;
 2.50 mm

SPANNERS OR WRENCHES, being ANY of the types listed in TABLE A,
 but NOT including ANY of the goods listed in TABLE B
                            TABLE A
   (a) ring;
   (b) combination (ring and open end);
   (c) flexible head;
   (d) open end
                            TABLE B
   (a) spanners or wrenches put up in packs with goods other than
       those listed in TABLE A;
   (b) spanners or wrenches or packs containing spanner or wrenches
       having one or both ends in ANY of the following sizes:
       (i) SAE or AF  :  7/32" to 1.5/8" (both inclusive);
       (ii) METRIC    :  4 mm to 28 mm (both inclusive) 30 mm, 32 mm
                         36 mm;
       (iii) WHITWORTH:  1/8" TO 1" (both inclusive);
       (iv)  BS       :  2BA, 1/4" to 1.1/8" (both inclusive)

HAND TOOLS, being EITHER of the following:
  (a) allen key sets;
  (b) hex keys

SPANNERS OR WRENCHES, hand operated, non adjustable

SPANNERS AND WRENCHES, non adjustable, being ANY of the following:
   (a) combination open end and ring;
   (b) open end;
   (c) ring

WRENCHES, adjustable, but NOT including ANY of the following:
   (a) pipe wrenches having a length of 850 mm or less, which
       incorporate a threaded adjustment for the jaw opening;
   (b) adjustable wrenches (OTHER THAN of the kind described in
       (a) above) having a length of 125 mm or less;
   (c) oil filter wrenches;
   (d) torque wrenches

SPANNERS OR WRENCHES, hook or pin type, but NOT including such
 spanners or wrenches put up in packs containing goods OTHER THAN
   such spanners or wrenches

SPANNERS OR WRENCHES, being ANY of the types listed in TABLE A,
 but NOT including ANY of the goods listed in TABLE B
                               TABLE A
   (a) ring;
   (b) combination (ring and open end);
   (c) flexible head;
   (d) box wrench
                               TABLE B
   (a) spanners or wrenches put up in packs with goods OTHER THAN
       those listed in TABLE A;
   (b) spanners or wrenches or packs containing spanners or
       wrenches having one or both ends in ANY of the following
       sizes:
         (i) SAE or AF : 7/32 in. to 1 7/8 in. (both inclusive),
                         2 in. to 2 1/4 in. (both inclusive),
                         2 3/8 in., 2 1/2 in., 2 5/8 in.,
                         2 3/4 in., 2 15/16 in. or 3 1/8 in.;
        (ii) Metric    : 4 mm to 28 mm (both inclusive),
                         30 mm, 32 mm, 36 mm, 38 mm, 41 mm, 46 mm,
                         50 mm or 55 mm;
       (iii) Whitworth : 1/8 in. to 3/4 in. (both inclusive),
                         7/8 in., 1 in. or 1 1/8 in.;
        (iv) BS        : 3/16 in. to 3/4 in. (both inclusive),
                         7/8 in., 1 in., 1 1/8 in. or 1 1/4 in.

WRENCHES, pipe, adjustable, being ANY of the following:
   (a) offset, having a jaw opening parallel to the handle;
   (b) vertical, being wrenches which do NOT incorporate a handle
       but have provision to accept, as a handle, a 1/2 in.
       (12.7 mm) square rod or a 1/2 in. (12.7 mm) drive socket
       wrench handle;
   (c) compound leverage, being wrenches which incorporate ALL of
       the following:
         (i) threaded adjustment of the jaw opening;
        (ii) chain pipe clamp;
       (iii) a compound leverage handle

SPANNERS, plumbers, basin, incorporating replaceable jaws and
 swivelling handles, but NOT including such spanners put up in
 packs with goods OTHER THAN such spanners

WRENCHES, lever, of the clamp, plier or vice type, but NOT
 including oil filter wrenches

WRENCHES, torque, digital, having ALL of the following:
   (a) interchangeable head system;
   (b) LED readout;
   (c) capable of storing, recalling and displaying measured torque
       values in internal memory;
   (d) RS232C input/output port
   (e) accuracy better than + 1% plus, 1 digit of each measured
       value
   but NOT including torque wrenches of the following types:
        (i) ratchet deflection beam type;
       (ii) ratchet type dual signal.

SPANNERS, adjustable, insulated, complying with IEC 900 standard,
 tested to 10 000 V

WRENCHES, ADJUSTABLE

SPANNERS AND WRENCHES, adjustable, non calibrated

SPANNERS OR WRENCHES, crowfoot, of the flare nut or open end type,
 but NOT including such spanners or wrenches put up in packs
 containing goods OTHER THAN crowfoot spanners or wrenches of
 flare nut or open end type

HANDLES FOR SOCKETS, 6.35 mm (1/4 in.) drive, whether imported
 separately or as a set consisting solely of such handles

SPANNER SOCKET SETS, having BOTH of the following:
  (a) NOT less than six sockets;
  (b) ratchet handle,
and NOT less than one of the following:
     (i) bit;
    (ii) bit holder;
   (iii) wrench;
    (iv) universal joint;
     (v) extension bar;
    (vi) bit socket;
   (vii) hex key;
  (viii) bit driver

INTERCHANGEABLE SPANNER SOCKETS, with OR without handles

SOCKETS AND/OR SOCKET ACCESSORIES, being ANY of the following:
   (a) sockets;
   (b) reducers;
   (c) tommy bars with sliding T (T handles);
   (d) extensions;
   (e) ratchets with coupler;
   (f) reversible ratchets;
   (g) couplers;
   (h) universal joints;
   (i) L-handles;
   (j) speed braces;
   (k) converters;
   (l) swivel handles;
   (m) driving handles (socket drivers);
   (n) ratchet adaptors

WRENCHES, tap, bar type

GIMLETS

TAP WRENCHES, HAND TOOL

DRILLING TOOLS, HAND AND/OR BIT BRACE RATCHET

HAMMERS, panel beaters", OTHER THAN ball pein or leather face
 hammers

MALLETS AND HAMMERS having ALL of the following:
   (a) coiled leather head NOT exceeding 70 mm diameter;
   (b) wooden handle;
   (c) able to strike sharpened cutting edges without splitting;
   (d) not including mallets with changeable or replaceable tips

HAMMERS, reboundless

INNER BEARING PULLERS, having ALL of the following:
  (a) slide hammer;
  (b) 4 bearing extractors;
  (c) storage case

HAMMERS AND/OR AXES, DRYWALL, handheld

HANDLES, HAMMER, IMPACT ABSORBING, comprising BOTH of the 
following:
  (a) rubber moulded outer skin;
  (b) internal steel wire core

HAMMERS OR SLEDGE HAMMERS OR MALLETS

CHISELS, wood carving, NOT being chisels having BOTH of the
 following:
   (a) rectangular blade cross-section;
   (b) cutting edge at 90 degrees to blade length

PLANES, wholly or principally of metal (but NOT including size
 No. 4 or equivalent smooth planes, whether smooth or corrugated
 bottom)

SHAVES OR SPOKESHAVES

CHISELS, WOODWORKING, but NOT including wood turning chisels AND 
all steel wood chisels

PLANES

SCREWDRIVERS, slotted head type with a tip width less than 3 mm,
 or recessed head type with a blade point size less than zero point

SCREWDRIVERS, torx recess type

SCREWDRIVERS, OTHER THAN allen, pozidriv, phillips or slotted
 head types

KEYS, torx recess type, and sets thereof

SCREWDRIVERS, spiral ratchet type

SCREWDRIVERS, torque limiting

SCREWDRIVERS, having 4 shoulders in parallel, capable of
 preventing "slipping" or "riding up" under torque

SCREWDRIVERS, offset, being screwdrivers which have the blade at
 an angle of 90 degrees to the body or handle

SCREWDRIVER SETS, being ANY of the following:
   (a) single handle and at least 3 interchangeable flat blade bits
       and 2 interchangeable Phillips head bits; OR
   (b) 6 screwdrivers comprising 2 or more Phillips head screwdrivers
       3 mm or less in width and 3 or more flat blade screwdrivers
       3.5 mm or less in width; OR
   (c) 8 screwdrivers, insulated to 1 000 V, comprising flat blade
       screwdrivers of 6 mm, 5 mm, 4 mm and 2.5 mm in width and 3
       Phillips head screwdrivers

SCREWDRIVERS, insulated, phillips or flat blade, complying with
 IEC 900 standard, tested to 10 000 V

SCREWDRIVERS, ball point or ball end, plastic handle, steel shaft
 and blade

SCREWDRIVERS

SETS, SCREWDRIVER, comprising ALL of the following:
  (a) Phillips head screwdrivers;
  (b) flat blade screwdrivers;
  (c) cases or hanging racks

CARE KITS, SUNGLASSES, comprising ALL of the following:
   (a) screwdriver;
   (b) lens cleaning cloth;
   (c) cleaning fluid;
   (d) plastic case

CAN OPENER with corkscrew attachment

SERVERS, ice-cream

STEELS, knife sharpening

BALLERS, melon

SHREDDERS OR GRATERS, CHEESE, having BOTH of the following:
   (a) stainless steel perforated blade;
   (b) handle

SLICERS, CHEESE, having BOTH of the following:
   (a) stainless steel slotted blade;
   (b) handle

TOOLS, MULTI-PURPOSE, incorporating a number of different working
 attachments which fold or insert into the housing

FIRESIDE TOOL SETS, black finish, having ALL of the following:
   (a) hearth brush;
   (b) poker;
   (c) shovel;
   (d) tool stand

BOTTLE OPENER, with cork screw and knife attachments

HOUSEHOLD TOOLS, hand operated bottle opener, comprising cork screw,
 knife or foil cutter and self adjusting flexible lever

HOUSEHOLD TOOLS, CAKE LEVELLER AND SLICER

SLICERS, FOOD, having BOTH of the following:
  (a) plastic body;
  (b) metal blades

CHIPPERS, POTATO

HOUSEHOLD TOOLS, being ANY of the following:
  (a) whisks;
  (b) graters;
  (c) food scoops;
  (d) ice cream scoops;
  (e) vegetable peelers;
  (f) garlic presses;
  (g) lemon presses or squeezers;
  (h) meat hammers;
  (i) pizza cutters;
  (j) food slicing guides

HOUSEHOLD TOOLS, being a combined apple corer AND wedger

HOUSEHOLD TOOLS, being a combination grater AND zester AND juicer

HOUSEHOLD TOOLS, being garlic presses incorporating a slicer

HOUSEHOLD TOOLS, having a metal working edge OR surface, being 
ANY of the following:
  (a) corn cob strippers;
  (b) strawberry slicers;
  (c) strawberry stem removers;
  (d) potato and/or rice presses;
  (e) avocado slicers;
  (f) bean slicers

SETS, COOKIE CUTTER, consisting of NOT less than 3 metal cutters

CUTTERS, COOKIE AND/OR SCONE

HOUSEHOLD TOOLS, SOFT FRUIT SLICER

HOUSEHOLD TOOLS, being ANY of the following:
  (a) can openers; 
  (b) graters;
  (c) peelers

HOUSEHOLD TOOLS, being zesters

COOKIE CUTTERS

HOUSEHOLD TOOLS, being ANY of the following:
  (a) apple corers;
  (b) egg slicers;
  (c) egg cutters;
  (d) jar openers;
  (e) knife sharpeners;
  (f) nut crackers;
  (g) tea bag squeezers

CUTTERS, POLYVINYL CHLORIDE FILM, hand operated, comprising BOTH 
of the following:
  (a) sliding head with metal cutting blade;
  (b) self adhesive strip

BOTTLE OPENERS, other than diecast, made from EITHER of the 
following:
  (a) plastic and stainless steel;
  (b) stainless steel

SNUFFERS, CANDLE, base metal

UTENSILS, being EITHER of the following:
  (a) mashers;
  (b) whisks

EXTRACTORS, CORK, having BOTH of the following:
   (a) dual spikes;
   (b) hinged handles

SHARPENERS, KITCHEN KNIVES, comprising ANY of the following:
   (a) tungsten carbide knife edge restorers;
   (b) diamond coated steel sharpening fingers;
   (c) hardened stainless steel honing fingers

SHARPENERS, KNIFE, being industrial diamond coated steel sharpening
 fingers, with OR without stabilising handles and safety hand guards

STRIPPING TOOL, cable and wire, pistol grip

TOOLS, cable and wire stripping, clam-shell type

STRIPPERS, coaxial wire and cable

APPLICATORS, hand held, adhesive tape dispensing, incorporating
 a metal cut off blade

TOOLS, deburring with interchangeable cutting blade

BLACKHEAD REMOVERS

TOOLS, riveting, but NOT including riveting tools suitable for
 smooth stemmed blind rivets which have a diameter within the
 range of 3.175 mm to 6.350 mm (both inclusive)

TOOLS, carpet or linoleum laying, being ANY of the following:
   (a) awls, carpet;
   (b) boxes, mitre;
   (c) clamps, carpet;
   (d) claws, pulling;
   (e) cutters:
         (i) carpet;
        (ii) cookie;
       (iii) cushion back;
        (iv) cushion lock;
         (v) loop pile;
        (vi) seam;
       (vii) strip;
   (f) cutting and hammering tools;
   (g) door pin tools;
   (h) driving bars, magnetic;
   (i) groovers;
   (j) hammers, staple;
   (k) kickers, knee;
   (l) lifters, moulding;
   (m) removers, staple;
   (n) repair tools, instant;
   (o) rollers:
         (i) extendable;
        (ii) lino;
       (iii) seam;
        (iv) wall;
   (p) spreaders, carpet;
   (q) squeezers, seam;
   (r) stair tools;
   (s) stretcher tools;
   (t) strippers, floor;
   (u) supports, corner;
   (v) tack holders, magnetic;
   (w) trimmers:
         (i) bar;
        (ii) carpet;
       (iii) corner;
        (iv) tucking;
         (v) wall;
   (x) trowels, stand up;
   (y) tubes for stretchers, auto-lock;
   (z) turning tools

TOOLS, hand, non-sparking, composed wholly (except for handles,
 if any) of beryllium copper

STEELS, knife sharpening

TOOLS put up in packs, provided that ALL components of those packs
 are individually goods to which Item 50 in Schedule 4 to the
 Customs Tariff Act 1987 would apply by virtue of Commercial
 Tariff Concession Orders made under Part XVA of the Customs Act

GLASS CUTTERS

TOOLS, combination, containing ALL of the following within
 a single body:
   (a) awl;
   (b) can/bottle opener;
   (c) combination plier;
   (d) file;
   (e) knife blade;
   (f) screwdriver blades

TOOLS, locksmiths", being ANY of the following:
   (a) lock picks;
   (b) key extractors;
   (c) tension tools;
   (d) plug holders;
   (e) plug followers;
   (f) car opening tools (commonly known as Slim Jims)

TROWELS, brick, (NOT being rectangular OR square trowels), steel
 blade, blade length 250 mm or greater

PUNCHES, alpha or numeric

TOOLS, cleaving, optical glass fibre

TOOLS, engraving or etching, metal printing plate making

GUNS, ear piercing, but NOT including such goods imported with
 ear studs

TOOLS, crimping, electrical connector, but NOT including such
 tools put up in packs containing electrical connectors

SETTING TOOLS, saw, but NOT including setting tools for bandsaws

TOOLS, bending, metal bar, rod or tube, mechanical lever type

BENDERS, tube, being a tool body with interchangeable bending
 jigs and formers

TOOLS, leather working

TOOLS, flat strapping, including tools which tension and seal
 the strapping, but NOT including wire tying tools

TOOLS, chainsaw chain repairing

PICKERS, textile

STRAIGHT EDGES, painting or wallpapering

GUNS, mastic dispensing

TOOLS, jewellers", but NOT including ANY of the following:
   (a) ring setting plates or punches;
   (b) doming or swaging blocks;
   (c) mandrels;
   (d) ring bending tools;
   (e) swage bars

TOOLS, chain breaker, bicycle or motorcycle

RESTORERS, thread pitch

SPLITTERS, metal nut

REMOVERS, staple

EXTRACTORS, lamp

KNIVES, being ANY of the following:
   (a) artists" painting;
   (b) paint scraping OR stripping;
   (c) putty OR filling;
   (d) scoring, interior decorating or wallpapering

KEYS, drill chuck

DRESSERS, grinding wheel

CUTTERS, tile

AWLS

DRIVERS, impact, screw or nut

TOOLS, tungsten tipped being EITHER of the following:
   (a) points;
   (b) pitching tools

REAMERS, tapered from 4 mm to 20 mm

TOOLS, CABLE TIE

TIGHTENERS, CHAIN, HAND OPERATED

TOOLS, TAPING AND FINISHING, being ANY of the following:
   (a) internal angle applicators;
   (b) hand operated flat finish box OR corner box finishers;
   (c) broad knives;
   (d) cement mixers;
   (e) corner rollers;
   (f) block OR universal sanders;
   (g) tapers

STAPLING HAMMERS OR PLIERS OR TACKERS, manually operated, with
 staple storage magazine

TOOLS, FLANGE SPREADING, PIPE

TOOLS, MULTI-PURPOSE, incorporating a number of different working
 attachments which fold or insert into the body

TOOLS, MULTI-PURPOSE, incorporating a number of different working
 attachments which fold or insert into the housing

TOOLS, CORNER FINISHING, gypsum drywall joints

PARTS OF FASTENING TOOLS, operated with disc magazine explosive
 charges

TOOLS, grabbing or retrieving incorporating ALL of the following:
   (a) retractable claw fingers or magnet;
   (b) flexible shaft and squeeze handle operation

TOOLS, riveting, capable of riveting ALL of the following sizes:
   (a) 2.4 mm;
   (b) 3.2 mm;
   (c) 4.0 mm;
   (d) 4.8 mm

PULLERS, being extracting tools, whether OR not in sets

TOOLS, repair, tyre valve or tube

HAND TOOLS, STUD TIGHTENING AND/OR REMOVING, steel, chrome-
plated, having thread diameter size NOT less than 6 mm and NOT 
greater than 19 mm

KITS, RIVET SETTING TOOLS, including ALL of the following:
  (a) ratchet hand rivet gun;
  (b) nose piece with nut;
  (c) mandrel;
  (d) threaded sleeve;
  (e) carry box

DISC BRAKE CALIPER SPREADERS, zinc plated steel

EXHAUST PIPE EXPANDERS, 3 piece, pipe diameters NOT less than 29 
mm and NOT greater than 87 mm

LOCK MORTICER, drill powered, having ANY one OR more of the 
following:
  (a) self-centering drill jig;
  (b) cutters;
  (c) drill shaft;
  (d) hook AND/OR height gauge;
  (e) adjustment tools;
  (f) carry case

STABILISATION STRUTS, RESCUE, having ALL the following:
  (a) load rated NOT greater than 1 500 kg;
  (b) extended length NOT greater than 1.95 m;
  (c) weight NOT greater than 9 kg

CLAMP TOOLS, BAND AND/OR GEAR CLAMPS

SETS, AUTOMOBILE ENGINE TIMING TOOL, consisting of ALL of the 
following:
  (a) oil pump tensioner lock;
  (b) crankshaft pulley bolt spacer;
  (c) valve remover;
  (d) tensioner locks;
  (e) camshaft locks;
  (f) crankshaft pulley holder

SQUEEZING TOOLS, POLYETHYLENE PIPE, having a rounding capacity 
diameter NOT less than 16 mm and NOT greater than 63 mm

SCRAPERS, PIPE END, having NOT less than five of the following:
  (a) threaded spindles, with OR without cross handles AND/OR 
      adjustment knobs;   
  (b) length setting catches;
  (c) piloting arm carriers;
  (d) piloting arm having a cylindrical handles;
  (e) blade holders AND blades;
  (f) scraper blades;
  (g) tensioning heads;
  (h) cylindrical heads;
  (i) star knobs

SCRAPERS, including high carbon steel blades

PARTS, CAULKING GUN, being metal plunger discs

HAND TOOLS, being ANY of the following:
   (a)  mitre boxes;
   (b)  wood and/or paint scrapers;
   (c)  oil cans;
   (d)  tackers and/or staplers;
   (e)  callipers;
   (f)  cement groovers and/or edgers;
   (g)  tile borers;
   (h)  tile cutters;
   (i)  floats;
   (j)  grout spreaders;
   (k)  trowels;
   (l)  adhesive spreaders;
   (m)  sanders;
   (n)  suction cups;
   (o)  hammer tackers;
   (p)  staple guns;
   (q)  plasterer's hawks;
   (r)  splatter guns;
   (s)  fibro cutters;
   (t)  joint rakers;
   (u)  tuck pointers;
   (v)  jointer, brick;
   (w)  tank and/or washer cutters;
   (x) tap reseaters;
   (y) honing guides;
   (z) riveters;
   (aa) tack lifters;
   (ab) brick carriers;
   (ac) brick line blocks;
   (ad) grout removers;
   (ae) glass cutters;
   (af) chalk line reels

HANDTOOLS, being powder actuated fasteners with OR without 
magazine

TIERS, CONCRETE REINFORCING BAR

PARTS, MASTIC GUN, being any of the following:
  (a) reducer;
  (b) reducer flange; 
  (c) bulkhead;
  (d) bulkhead bung;
  (e) bulkhead adaptor;
  (f) bulkhead insert; 
  (g) return pusher;
  (h) handle;
  (i) plunger; 
  (j) plunger rod;
  (k) drive rod;
  (l) cartridge support;
  (m) sleeves;
  (n) frame assembly; 
  (o) yoke;
  (p) release plate; 
  (q) catch plate;
  (r) zinc knob;
  (s) plastic cap;
  (t) barrel;
  (u) nozzle holder

SETS, FASTENING HAND TOOL, explosive charge operated 
incorporating a strip magazine, including ALL of the following:
  (a) safety glasses;
  (b) ear plugs;
  (c) allen keys;
  (d) brushes;
  (e) manuals;
  (f) clips;
  (g) steel balls;
  (h) carry case

HAND TOOLS, being ANY of the following:
  (a) battery terminal cleaners;
  (b) brake adjustment tools;
  (c) door clip and spring removers;  
  (d) grease guns;
  (e) piston ring compressors;
  (f) pickup tools;
  (g) tie rod end separators;
  (h) valve lifters;
  (i) windscreen removers

TOOLS, GRABBING, REACHING AND RETRIEVING, comprising BOTH of the 
following:
  (a) jaws or magnet grippers;
  (b) squeeze handles or triggers or scissor controls

TOOLS, TERMINATING, TELEPHONE WIRE, hand held

DOVETAIL JIGS and attachments, fully adjustable, in sizes 12 inch
 or 24 inch

BOXES OR GUIDES, mitre

OILWELL PUMPING EQUIPMENT, being ANY of the following:
   (a) wire line clamps;
   (b) polished rod clamps;
   (c) stuffing box clamps;
   (d) polished rod grips;
   (e) tubing tongs;
   (f) non-spark bell nipples

JIGS, arrow fletching

GRIPS, wire, having a safe load capacity exceeding 900 kg

PARTS, FOR ANY OF THE FOLLOWING:
   (a) drill pipe slips;
   (b) drill collar slips;
   (c) casing safety clamps

PIPE SQUEEZE OFF TOOLS

GRIPS, CABLE, being any of the following:
   (a) lashing wire grips;
   (b) figure 8 grips;
   (c) pvc covered conductor come-along grips
 but NOT including stocking, sock or mesh type pulling grips

WORK STANDS, bicycle, complete with adjustable holding clamp

TONGS, having a working load or torque capacity of 3 000 N.m or
 greater

GRABS, ROPE OR WIRE, having BOTH of the following:
   (a) gravity operated internal spring;
   (b) breaking load NOT less than 1 900 kg

YOKE TOOLS, WIND TURBINE, with OR without ANY of the following: 
  (a) transport frames;
  (b) storage container;
  (c) jacking screws;
  (d) sliding sticks;
  (e) aluminium storage container top;
  (f) tarpaulin

TOOLS, VALVE SPRING COMPRESSOR, steel, including ALL of the 
following:
  (a) throat clearance NOT greater than 150 mm;
  (b) compression capability NOT less than 75 mm and NOT greater 
than 165 mm;
  (c) PVC coated handle

COIL SPRING COMPRESSORS, carbon steel

POCKET HOLE JIGS, having ANY of the following:
  (a) drill jig;
  (b) drill bits;
  (c) driving bits;
  (d) stop collar;
  (e) material thickness gauge;
  (f) dust collection blade;
  (g) screws;
  (h) clamps;
  (i) hex wrench;
  (j) docking station

SETS, PIPE CLAMP, consisting of ALL of the following:
  (a) pipe holder with ratchet strap;
  (b) carrier bars;
  (c) pulling strap with holder;
  (d) pulling shoes;
  (e) pulling slides including ratchet

TEST CLAMPS, VERTICAL CONNECTION SYSTEM, SUBSEA, incorporating a 
blind hub OR blind flange

GUTTER CLAMPS, LADDER, having adjustable locking jaw

CABLE LOCKS, hand adjustable, comprising ALL of the following:
  (a) zinc alloy casings;
  (b) sintered steel locking wedges;
  (c) stainless steel springs

GRABS, ROPE OR WIRE, having BOTH of the following:
   (a) gravity operated internal spring;
   (b) breaking load NOT less than 1 900 kg

CLAMPS

VICES

KITS, HAND TOOL, non-magnetic, non-sparking, including NOT less  
than ANY 5 of the following categories:
  (a) shovels;
  (b) picks;
  (c) pry bars;
  (d) hammers;
  (e) chisels;
  (f) scrappers

TOOL SETS, consisting of ALL of the following:
   (a) screwdriver set;
   (b) long nose locking pliers;
   (c) curved jaw locking pliers

SETS, TIMING TOOLS, consisting of ALL of the following:
  (a) hand tools;
  (b) fittings;
  (c) gauges;
  (d) case

TOOL KITS, BICYCLE, in cases OR boxes OR saddle bags, consisting 
of NOT less than a combination of ANY two of the following 
categories:
  (a) screwdrivers;
  (b) spanners;
  (c) cassette lock-ring removal tools;
  (d) wrenches;
  (e) freewheel turners tools;
  (f) crank arm removal tools;
  (g) crank extractor tools;
  (h) spoke adjuster;
  (i) metal tyre levers;
  (j) bottom bracket AND/OR headset locking ring tools;
  (k) bottom bracket removal tools;
  (l) socket tool adaptors;
  (m) freewheel removing tools;
  (n) hex keys;
  (o) wrench sockets;
  (p) crank arm dust cap tools;
  (q) cable cutters;
  (r) multipurpose folding tools;
  (s) chain remover tools;
  (t) chain rivet extractor tools;
  (u) chain fixing pliers;
  (v) chain cleaning tools,
with OR without ANY of the following:
       (i) tyre patches;
      (ii) tyre cement;
     (iii) grease;
      (iv) plastic tyre lever;
       (v) crank extractor nut;
      (vi) chain wear indicator;
     (vii) valve adaptors;
    (viii) chain cleaner brush

SETS, TOOL, COMPRESSION, consisting of ALL of the following:
  (a) operating instructions;
  (b) transport case;
  (c) pipe cutter;
  (d) compression tool;
  (e) expander tool;
  (f) cleaning brush;
  (g) lubricant gel

KITS, TOOL, COMPRESSION, consisting of ALL of the following:
  (a) operating instructions;
  (b) transport case;
  (c) pipe cutter;
  (d) compression jaws;
  (e) compression tool;
  (f) expander heads;
  (g) expander tool;
  (h) cleaning brush;
  (i) lubricant gel

TOOL SETS, comprising tools in NOT less than five of the 
following categories:
  (a) sockets;
  (b) ratchets;
  (c) universal joints;
  (d) extension bars;
  (e) wrenches;
  (f) pliers;
  (g) screwdrivers;
  (h) screwdriver bits;
  (i) knives

KITS, TOOL, comprising not LESS than ANY two of the following:
  (a) allen keys;
  (b) chisels;
  (c) crimpers;
  (d) files;
  (e) hammers;
  (f) multi grips;
  (g) pliers;
  (h) punches;
  (i) saws;
  (j) screwdrivers;
  (k) shears;
  (l) snips;
  (m) sockets;
  (n) spanners;
  (o) wrenches

TOOL SETS, comprising tool box and NOT less than ANY five of the 
following:
  (a) pliers;
  (b) hammers;
  (c) spanners;
  (d) socket sets comprising interchangeable spanner sockets and
      handles;
  (e) punches;
  (f) chisels;
  (g) hex keys;
  (h) hacksaws

BITS, rotary percussive rock drilling, but NOT including ANY
 of the following:
   (a) bits designed for use with down-the-hole percussive
       hammers capable of drilling holes with a nominal diameter
       of 88 mm or greater;
   (b) bits designed for use with top-hole percussive hammers
       capable of drilling holes with a nominal diameter of 100 mm or
       greater;
   (c) integral drill steels;
   (d) rods with bits, being ANY of the following:
         (i) tapered drill rods;
        (ii) extension rods;
       (iii) speed rods (male/female);
        (iv) drifter rods;
         (v) shank rods;
        (vi) guide rods

BITS, rock drill, rotary tricone type, having provisions for air
 or fluid circulation

BITS, TOP HAMMER, ROTARY, PERCUSSIVE, consumable type, having a
 diameter of less than 68 mm

SCRAPERS, BORING HEAD, TUNNEL BORING MACHINE

PARTS, DRILLING MACHINE, being ANY of the following:
  (a) teeth;
  (b) horizontal directional drilling (HDD) drill bits;
  (c) rock drill bits;
  (d) pilot drill bits;
  (e) bars;
  (f) round shank bits;
  (g) drilling interchange bar system, consisting of ALL of the
      following:
          (i) interchange bars;
         (ii) bar holders;
        (iii) screw connectors,
  (h) scraper blades;
  (i) shank assemblies, consisting of BOTH of the following:
          (i) shank bit holder;
         (ii) drill bits

PARTS, FOUNDATION DRILLING MACHINE, being ANY of the following:
  (a) casing shoes or coring tools weld on bars having BOTH of 
the following:
        (i) three or more tungsten carbide inserts; and
        (ii)length NOT greater than 110 mm;
  (b) casing shoes or coring tools quick change bars with three 
or more tungsten carbide inserts;
  (c) flat teeth with a height NOT less than 155 mm
  NB Conical tools are excluded from this order

BITS, rock drill, rotary tricone type, having provisions for air
 or fluid circulation

BLANKS, tool, consisting of a synthetic polycrystalline diamond
 layer bonded to a tungsten carbide substrate

BITS, rock drill, having BOTH of the following:
   (a) cutting structure of diamonds (whether or not natural
       diamonds);
   (b) dia exceeding 450 mm

PARTS, 600 MM OR GREATER DIAMETER ROCK DRILLING RAISE BORER, being
 ANY of the following:
   (a) stems;
   (b) saddles;
   (c) cutters;
   (d) base heads;
   (e) segments;
   (f) segment supports;
   (g) extension segment;
   (h) wear pads;
   (i) wedges

NOZZLES, ROTARY TRICONE ROCK DRILL BIT

BITS, DRILLING, OIL AND GAS, POLYCRYASTALLINE DIAMOND (PDC), having
 ALL of the following:
   (a) bit whirl resistance;
   (b) hydraulic cleaning of cutting structure;
   (c) with or without impregnated diamond secondary cutter
       structure;
   (d) in all sizes greater than 105.77 mm diameter

HOLE ENLARGER, incorporating seamless rotating cutting wheels, and
 parts as follows:
   (a) wear rings;
   (b) body;
   (c) locking rings;
   (d) ball rings;
   (e) conical bushing;
   (f) lubricant cylinders;
   (g) caps;
   (h) blind plugs;
   (i) ball retainers;
   (j) wedges;
   (k) counterweights;
   (l) shafts;
   (m) wear sleeves;
   (n) plungers;
   (o) cutter wheels;
   (p) lubricant pistons

BITS, ROCK DRILL, button type, air or fluid flushing

BITS, OIL/GAS DRILLING, polycrystalline diamond (PDC) and natural
 diamond (ND) cutting structure, having ALL of the following:
   (a) whirl reducing capability;
   (b) hydraulic cleaning and cooling features;
   (c) back up secondary cutting structure of natural diamond
       impregnated studs;
   (d) in all sizes greater than 105.77 mm

BITS, CORING, POLYCRYSTALLINE DIAMOND OR NATURAL DIAMOND CUTTING
 STRUCTURE

NOZZLES, ROCK DRILL BIT, DIAMOND CUTTING STRUCTURE

BITS, ROCK DRILL, DIAMOND CUTTING STRUCTURE, diameter NOT less than
 215.9 mm and NOT greater than 444.5 mm

DRILL RODS, integral

CUTTER BLOCKS, REAMER, including top inserts

CUTTING TOOLS, TUNNEL BORING MACHINE, interchangeable, being 
one OR both of the following:
  (a) disc cutters;
  (b) cutting knives

PARTS, AUGER AND/OR CORE BARREL AND/OR CASING SHOE, FOUNDATION 
DRILLING MACHINE, being one OR both of the following:
  (a) tool holders;
  (b) stop wedges

PARTS, AUGER, FOUNDATION DRILLING MACHINE, being EITHER of the 
following:
  (a) tool holders;
  (b) stop wedges

DRILL BITS, single use, cast iron

AUGER PIERS, EARTH BORING, BUILDING FOUNDATION, self locking

PLATES, wire drawing, multi-holed

DIES, WIRE DRAWING, tungsten carbide nib having an inside diameter
 NOT exceeding 7 mm in steel case with internal polished form

DIES, DRAWING, 28 mm x 14 mm, having ALL the following
 specifications:
   (a) steel cased with a fixed tungsten carbide nib finished to a
       lead angle of 11 degrees and an exit angle of 26 degress
       +/- 0.25 degrees;
   (b) sizes range from 0.150 mm to 1.800 mm (inclusive) with a
       surface finish roughness of RA=0.4, maximum tolerance
       +/- 0.001 mm;

DIES, WIRE DRAWING, tungsten carbide

PUNCHES, sheet metal, hand held, key operated

PATTERN PRICKERS, PERFORATING PUNCHES OR PERFORATING TUBES, single
 or double edged

PUNCHES, cross recess screwhead

PUNCH UNITS, for aluminium can body making machine

FORMING TOOL, including ALL of the following:
  (a) cavity heads;
  (b) cutting ring;
  (c) pneumatic ejecting stop;
  (d) smoothing ring

CAUL PLATES, LAMINATION

DIES, DRILL POINT

TOOLS AND DIES, necking, aluminium can body

TOOLS, having tips made from EITHER of the following:
   (a) high speed tool steel having EITHER of the following:
         (i) a content NOT less than 22% by weight of tungsten;
        (ii) a content NOT less than 12% by weight of cobalt;
   (b) high speed vanadium steel capable of machining steel
       containing NOT less than 10% by weight of manganese

DIES, button (thread cutting), high speed steel, ground thread
 For the purposes of TC 8533688 "high speed steel" means steel
 that contains:
   (a) NOT less than 0.60% by weight of carbon; and
   (b)   (i) chromium; or
        (ii) vanadium; or
       (iii) cobalt; and
   (c)   (i) molybdenum and tungsten, in such percentages by
             weight that the sum of the number equal to the
             percentage of tungsten and the number equal to
             twice the percentage of molybdenum is NOT less
             than 13.5%; or
        (ii) NOT less than 7% by weight of molybdenum; or
       (iii) NOT less than 14% by weight of tungsten

COMPOSITE TOOL BODIES (HOLDERS), METAL WORKING, but NOT including
 tool bodies imported with tool tips plates OR sticks

THREAD ROLLING DIES, SELF TAPPING SCREWS

STEPDRILLS, multistep, single flute, capable of drilling and
 deburring more than 5 individual hole sizes in metal, wood, plastic
 and the like

BITS, core, tungsten carbide tipped

DRILLS, high speed steel, dia NOT exceeding 0.29 mm

BITS, machine tool, being woodworking drilling bits, but NOT
 including ANY of the following:
   (a) dowelling bits having a dia exceeding 6.2 mm but NOT
       exceeding 15.9 mm;
   (b) flat power bits having a dia exceeding 9.5 mm but NOT
       exceeding 25.4 mm;
   (c) machine bits with scotch pattern noses or jennings pattern
       noses;
   (d) router bits;
   (e) single flute wood bits having a dia exceeding 1.50 mm
       but NOT exceeding 9.55 mm;
   (f) twin flute wood bits having a dia exceeding 6.2 mm but
       NOT exceeding 12.7 mm;
   (g) wood screw pilot bits NOT capable of drilling holes having
       a depth exceeding 38 mm
   For the purposes of TC 8431291 the machine bits excluded may
   be of the solid centre type or the double twist type

DRILL TIPS, tubular, tungsten carbide coated

DRILLS, twist, wholly tungsten carbide

DRILLS, taper shank with coolant hole, Imperial dia Size 15/32 in.
 or greater but NOT exceeding 2 in., but NOT including drills
 of ANY of the following Imperial Sizes:
   (a) 1/2 in.;
   (b) 5/8 in.;
   (c) 23/32 in.;
   (d) 25/32 in.;
   (e) 29/32 in.;
   (f) 1 in.;
   (g) 1 1/16 in.;
   (h) 1 3/16 in.;
   (i) 1 1/2 in.

BITS for braces, fencing and wagon, square taper shanked, having
 a twist of NOT less than 200 mm and an overall length of NOT less
 than 300 mm

BITS, AUGER, scotch pattern

DRILLS, chisel tip auger

COMPOSITE TOOL BODIES (HOLDERS), METAL WORKING, but NOT including
 tool bodies imported with tool tips, plates or sticks

DRILL BITS, ELECTRO-PNEUMATIC ROTARY HAMMER, tungsten carbide
 tipped, having a shank geometry of EITHER of the following:
   (a) slotted drive;
   (b) triangular

DRILL BITS, MASONARY, HAMMER, having BOTH of the following:
   (a) slotted shank;
   (b) hammer proof carbide tip

DRILLS, GUN, as follows:
   (a) being ANY of the following;
         (i) carbide tipped;
        (ii) solid carbide;
       (iii) solid carbide heads,
   (b) having ALL of the following;
         (i) standard driver;
        (ii) coolant channels through centre;
       (iii) tip off-centre,
   (c) having EITHER of the following;
         (i) length greater than 300 mm;
        (ii) length less than or equal to 300 mm, with outside
             diameter less than 6 mm or greater than 25.3 mm

GUN DRILLS, having ALL of the following:
  (a) being ANY of the following:
        (i) carbide tipped;
       (ii) solid carbide;
      (iii) solid carbide heads;
  (b) having ALL the following:
        (i) standard driver;
       (ii) coolant channels through centre;
      (iii) tip off centre;
  (c) but NOT including ANY of the following:
        (i) diameter exceeding 5.99 mm but NOT exceeding 25.3 mm;
       (ii) length NOT greater than 300 mm

SAW DRILLS, being drill bits that use the first 25mm (one inch) or
 so of the drill bit to drill through the desired material, then use
 the rest of the special shaft as a cutting tool or saw

DRILL BITS, conical countersink, high speed steel, 90 degree 
angle, with OR without case

TWIST DRILL BITS, high speed cobalt, stepped tip, with OR 
without case

TWIST DRILL BITS, high speed steel, stepped tip, with OR without 
case

TWIST DRILL BITS, high speed steel, 118 degree tip angle, with 
OR without case

TWIST DRILL BITS, high-speed steel, 130 degree tip angle, with 
OR without case

DRILL BITS, stepped twist,  high speed steel, with OR without 
case

TWIST DRILL BITS, high speed steel, titanium nitride head 
coated, with OR without case

ROUNDING RINGS, POLYETHYLENE PIPE, galvanised steel, having ALL 
of the following:
  (a) rounding capacity diameter NOT less than 63 mm and
      NOT greater than 250 mm;
  (b) hinged;
  (c) nut AND thread closure

CORERS, DIAMOND TIPPED, having a diameter NOT greater than 
600 mm

BITS, MASONRY CORE, having ALL of the following:
  (a) diamond segments;
  (b) hex shank drive;
  (c) diameter NOT less than 6 mm AND NOT greater than 50 mm

TUBES, DRILL BIT, having a length NOT greater than 2 metres

BITS, TAPHOLE, BLAST FURNACE

BITS, machine tool, being woodworking boring bits, but NOT
 including ANY of the following:
   (a) dowelling bits having a dia exceeding 6.2 mm but NOT
       exceeding 15.9 mm;
   (b) flat power bits having a dia exceeding 9.5 mm but NOT
       exceeding 25.4 mm;
   (c) machine bits with scotch pattern noses or jennings pattern
       noses;
   (d) router bits;
   (e) single flute wood bits having a dia exceeding 1.50 mm
       but NOT exceeding 9.55 mm;
   (f) twin flute wood bits having a dia exceeding 6.2 mm but
       NOT exceeding 12.7 mm;
   (g) wood screw pilot bits NOT capable of drilling holes having
       a depth exceeding 38 mm
   For the purposes of TC 8632394 the machine bits excluded may be
   of the solid centre type or the double twist type

REAMERS, adjustable

BROACHES, spline, of the hexagonal, square, rectangular, serrated,
 straight sided or keyway types, length of tooth area 762 mm or
 greater

COMPOSITE TOOL BODIES (HOLDERS), METAL WORKING, but NOT including
 tool bodies imported with tool tips, plates or sticks

BROACHES, tungsten carbide tipped, having ALL of the following:
  (a) cutter diameter NOT less than 17.5 mm and NOT greater than
      100 mm;
  (b) cutting depth NOT greater than 75 mm;
  (c) side lock shank OR one touch shank;
  (d) full circle cutting surface

TOOLS, being oil and gas well casing reaming shoes

BURRS, rotary, being interchangeable tools for power operated
 hand tools

TOOLS, having tips made from EITHER of the following:
   (a) high speed tool steel having EITHER of the following:
         (i) a content NOT less than 22% by weight of tungsten;
        (ii) a content NOT less than 12% by weight of cobalt;
   (b) high speed vanadium steel capable of machining steel
       containing NOT less than 10% by weight of manganese

HOBS, having a dia 38 mm or less OR 204 mm or greater

CUTTERS, square shoulder milling, in the form of square shoulder
 shell mill types or end milling types, incorporating parallel
 shanks or morse taper shanks and having indexable throwaway
 cutting inserts

CUTTERS, gear shaper, single, paired or in tandem, being ANY of
 the following:
   (a) chain sprocket, disc type;
   (b) extended boss;
   (c) gear shaving;
   (d) helical, for continuous tooth double helical gears;
   (e) helical disc;
   (f) hub;
   (g) rack;
   (h) shank;
   (i) special form;
   (j) spline disc;
   (k) spur disc

COMPOSITE TOOL BODIES (HOLDERS), metal working, having an
 effective cutting diameter NOT exceeding 205 mm but NOT
 including tool bodies imported with tool tips, plates OR sticks

CONVERSION AND MODIFICATION EQUIPMENT, AUTOMOTIVE ENGINE COMPONENT
 MANUFACTURING AND/OR ASSEMBLY MACHINES, being ANY of the following:
   (a) double over-head cam engine head milling cutters OR indexible
       carbide insert milling cutters;
   (b) cylinder block, cylinder head, bearing bridge OR oil pan
       milling cutters OR indexible carbide insert milling cutters

TOOLS, OR TOOL HEADS, MILLING, DOWNHOLE, OIL AND GAS WELL

COMPOSITE TOOL BODIES (HOLDERS), metal working, but NOT including
 tool bodies imported with tool tips, plates, sticks or the like

BLANKS, tool, consisting of a synthetic polycrystalline diamond
 layer bonded to a tungsten carbide or stainless steel substrate

BLADES, deburring tool

TOOLS, interchangeable, masonry, being EITHER of the following:
   (a) scrapers;
   (b) lettering and carving

POWER TOOL SETS, comprising BOTH of the following:
   (a) screwdriver bits;
   (b) nut drivers

WHEELS, glass sheet edging, diamond impregnated, concave pencil
 type

EXPANDING OR CLEANING TOOLS, boiler tube, heat exchanger tube or
 condenser tube, being interchangeable tools for machine tools
 or power operated hand tools

CHISELS, electro-pneumatic rotary hammer

SCUTCH COMBS

SCREWDRIVER BLADES, interchangeable, OTHER THAN allen, pozidriv,
 phillips or slotted head types

NIBBLERS, sheet metal, being attachments for electric drills

TOOLS, having tips made from EITHER of the following:
   (a) high speed tool steel having EITHER of the following:
         (i) a content NOT less than 22% by weight of tungsten;
        (ii) a content NOT less than 12% by weight of cobalt;
   (b) high speed vanadium steel capable of machining steel
       containing NOT less than 10% by weight of manganese

STAMPS, leather

DRESSERS, diamond, truing grinding wheel

BITS, wire wrapping or wire unwrapping tool

BITS, screwdriving, power tool, including bits with finder sleeves

BITS, screwdriving, having 4 shoulders in parallel, capable of
 preventing "slipping" or "riding up" under torque

ACCESSORIES, SPIRAL RACHET SCREWDRIVER, being ANY of the
 following:
   (a) adaptors;
   (b) countersink bits;
   (c) drill points;
   (d) screwdriving bits

EXTRACTORS, screw threading tap

CUTTERS, router, solid carbide, having BOTH of the following:
   (a) spiral cut flutes;
   (b) a dia of 1.0 mm or greater but NOT exceeding 2.4 mm

TOOLS, PERCUSSION, HYDRAULIC BREAKER

COMPOSITE TOOL BODIES (HOLDERS), METAL WORKING, but NOT including
 tool bodies imported with tool tips, plates or sticks

INTERCHANGEABLE HEADS, 16 or 22 mm diameter female recess, being
 ANY of the following spanner types:
   (a) fixed square drive;
   (b) open end;
   (c) flare (crowsfoot) end;
   (d) ratchet square drive;
   (e) ring end

HOLESAWS, comprising ALL of the following:
   (a) carbide tipped blade;
   (b) arbor;
   (c) pilot drill

TOOLS, PIPE BENDING MACHINE, interchangeable, including ANY of 
the following:
  (a) mandrels;
  (b) dies;
  (c) wiper;
  (d) clamp

CUTTING TIP BUTTONS, CUTTER DISC, having BOTH of the following:
  (a) tungsten carbide base;
  (b) polycrystalline top layer

ADAPTERS, COFFEE POD, PORTABLE ESPRESSO COFFEE MACHINES

PRESS RINGS, METALLIC PRESS CONNECTOR PIPE SYSTEM, phosphatised 
coated steel, with OR without ANY of the following:
  (a) adaptor jaws;
  (b) moulded plastic case

TOOL HEADS, DRILL POLE

CORE CUTTERS, POLYETHYLENE PIPE, including ALL of the following:
  (a) pilot drill;
  (b) adaptors;
  (c) core cutter diameter NOT less than 46 mm and NOT greater 
      than 400 mm

KITS, HOLE SAW, consisting of ALL of the following:
  (a) hole saw blades;
  (b) arbor;
  (c) pilot drill, 
with OR without EITHER of the following:
        (i) ejector springs;
       (ii) carry case

PARTS, HANDHELD INTERCHANGEABLE ELECTRIC TOOL, being scrapers

TOOLS, DEBARKER, being tool body AND/OR cutting tip

ROTARY PROFILE CUTTERS, carbide

ACCESSORIES, HAND TOOL, interchangeable, being ANY of the 
following:
   (a) grinding discs;
   (b) rasping bits;
   (c) cutting blades;
   (d) polishing discs

PARTS, EXPANDER TOOL, being expander heads

KITS, HOLESAW, comprising ALL the following:
  (a) holesaw blades;
  (b) mandrels;
  (c) arbors, with OR without adapters;
  (d) carry case

HOLESAWS

GUIDE SHOES, CASING, OIL AND GAS WELL

HEXAGON BIT AND DRIVER SETS, comprising NOT less then ANY 3 of 
the following:
  (a) adapters;
  (b) drill bits;
  (c) hexagon head driver bits;
  (d) screw guides;
  (e) replacement screws;
  (f) screw driver bits;
  (g) nut drivers;
  (h) bit holders

CRIMPING JAWS, interchangeable, with or without carry case

HOLESAWS, diamond coated

HOBS, GEAR CUTTING, spiral bevel

KNIVES OR CUTTING BLADES, gear making machine

KNIVES OR CUTTING BLADES, strapping and tying machine

BLADES, shear or nibbler cutter, portable sheet metal cutting
 power tool

BLADES, cutting, pneumatic hand held nipper

SLITTING KNIVES, STEEL COIL SLITTING LINE, metal, having BOTH of 
the following:
  (a) thickness NOT less than 3 mm and NOT greater than 30 mm;
  (b) accuracy tolerance of blade plus OR minus 0.003 mm

SLITTER KNIVES, having ALL the following:
  (a) outside diameter NOT greater than 450 mm;
  (b) thickness NOT greater than 40 mm;
  (c) lapped surface

BLADES, log de-barking machine

BLADES, KNIFE RING FLAKER BLADE ASSEMBLY

PARTS, HANDHELD INTERCHANGEABLE ELECTRIC TOOL, being wood 
cutting blades

KNIVES, WOOD SAW MACHINE, being EITHER of the following:
  (a) chipping knives;
  (b) edging knives

BLADES, PLANER, double edged, tungsten carbide tipped

KNIVES AND CUTTING BLADES, fruit or vegetable, being replacement
 parts for industrial/commercial food processing machines

PARTS FOR MEAT EMULSIFYING MACHINES, being ANY of the following:
   (a) cutting head with feeding disc;
   (b) cutting ring;
   (c) insert ring;
   (d) cutting head with feeding spiral

KNIVES OR PLATES, meat grinder/mincer, having a dia NOT exceeding
 85 mm

KNIVES, spiral machine, meat slicing, angles 10 degrees/20 degrees,
 10 degrees/33 degrees and 10 degrees/20 degrees/33 degrees

BLADES, FOOD PROCESSOR

FOOD PROCESSOR ATTACHMENTS, having ALL of the following:
  (a) stainless steel cutting disc;
  (b) cutter basket;
  (c) drive shaft;
  (d) cutter lid with feeder tube;
  (e) pusher

ROLLERS, CUTTING, stainless steel

PARTS, BLENDER, being stainless steel cross blades

KNIVES, CHIPPING, LOG REDUCING HEADS, being two angled chipping 
faces at 53 degrees to each other, having ALL of the following;
  (a) length NOT greater than 95 mm;
  (b) width NOT greater than 74 mm;
  (c) thickness NOT greater than 16 mm

SHEAR BLADES, molten glass gob, high speed steel, capable of
 operating at temperatures in excess of 800 degrees C

BAND KNIVES, continuous steel, rubber, cork or leather splitting

KNIVES OR CUTTING BLADES, industrial sewing machine

BLADES, loop pile cutting machine

RULES, steel, creasing, cutting or perforating

KNIVES OR CUTTING BLADES, strapping and tying machine

KNIVES OR CUTTING BLADES (OTHER THAN press knives or leather
 splitting knives), footwear making machinery

KNIVES OR CUTTING BLADES (OTHER THAN rotary slitting knives),
 envelope window cutting machine

KNIVES OR CUTTING BLADES, cylindrical, leather skiving machine

BANDS, paper perforating, flexible steel, offset printing press

KNIVES, CIRCULAR, ROTARY PAPER LOG SAW, being alloy steel containing
 chromium, molybdenum and vanadium

KNIVES OR CUTTING BLADES, SPIRAL, being ANY of the following:
   (a) carpet shearing;
   (b) leather shaving;
   (c) hide fleshing;
   (d) leather frizzing;
   (e) textile shearing;
   (f) sheepskin shearing

KNIVES OR CUTTING BLADES, domestic sewing machine

CUTTING BLADES, chromium nickel alloy, for EITHER of the 
following:
  (a) aseptic thermoplastic tubing welder;
  (b) aseptic thermoplastic disconnector hand tool

KNIVES AND/OR CUTTING BLADES, RE-CYCLED PLASTIC PROCESSING, with 
OR without holders

PARTS, HANDHELD INTERCHANGEABLE ELECTRIC TOOL, being cutting 
blades

TIPS, cobalt base alloy, rectangular, having a width of .090 inches
 to .450 inches

SAW TOOL BLANKS OR SAW TIPS, tungsten carbide, being tips preground
 to an accuracy of + or - 0.001 in.

TOOL BLANKS AND INSERTS, cutting, consisting of a layer of cubic
 boron nitride and a cemented tungsten carbide substrate

INSERTS, METAL CUTTING, MACHINE TOOL, having BOTH of the following:
   (a) cemented carbide substrate material;
   (b) ceramic coating

TIPS, saw, sintered tungsten carbide, double bevel, left and right
 hand

NIBS, WIRE DRAWING DIE, tungsten carbide

BIT INSERTS, ROCK DRILLING MACHINE, tungsten carbide, unfinished 
blank AND/OR finished insert

BLANKS, tungsten carbide, being ANY of the following:
  (a) rectangles;
  (b) squares;
  (c) triangles;
  (d) rods;
  (e) cones;
  (f) cylinders;
  (g) strips

INSERTS, METAL WORKING MACHINE TOOL

INSERTS, METAL CUTTING MACHINE TOOL, cubic boron nitride

GRINDING MILLS, salt or pepper, being tableware essentially of
 plastic or glass and combinations thereof, but NOT including
 wooden mills or mills which contain wooden parts

MINCERS, meat

CHOPPERS, food

SLICERS, vegetable, hand operated, whether or not including
 protective carriages for use therewith

SLICERS, food, circular blade, domestic, hand operated

CRUSHERS, ice, domestic, hand operated

APPLIANCES, BISCUIT SHAPING, hand held, which may also dispense
 cream or fill cakes

CORK EXTRACTOR, lever type

SCOOPS, ICE CREAM

EXTRACTORS, cork, Archimedean action, being EITHER of the following:
   (a) without built in foil cutter; OR
   (b) in sets with a separate foil cutter

SIFTERS, flour, domestic, hand operated

DISPENSERS, dough, hand held, capable of shaping and dispensing
 doughnut and pancake batter

COFFEE PREPARATION APPLIANCES, being ANY of the following:
  (a) coffee maker with milk steamer;
  (b) milk steamer;
  (c) cup filter basket reducer

COFFEE MAKERS, ESPRESSO, manually operated, with OR without 
carry cases

FOOD PROCESSORS, hand operated, whether OR not in sets, having 
NOT less than three of the following:
  (a) choppers;
  (b) graters;
  (c) raspers; 
  (d) slicers;
  (e) peelers

SETS, HOUSEHOLD, comprising ALL of the following:
(a) can opener;
(b) ice cream scoop;
(c) pizza cutter;
(d) peeler

EGG BEATERS, hand operated

OPENERS, CAN, having a hand operated mechanical mechanism

SUSHI MAKERS

UTENSILS, being ice cream spoons

MILLS, GRINDING, SALT AND PEPPER, wooden

SETS, assorted articles, comprising of kitchen knives and
 self sharpening receptacle/s, with or without receptacle
 mounting brackets or self sharpening kitchen shears

KNIVES, sets, with hollow ground cutting edge and blade thickness
 not exceeding 1.6 mm, with or without knife block

HOBBY CRAFT TOOL SETS, having a weight NOT exceeding 700 gms,
 comprising ANY of the following :
   (a) hobby knife;
   (b) assorted blades;
   (c) mitre box;
   (d) razor saw blade

SETS, KNIFE, self-sharpening, comprising BOTH of the following:
  (a) knife;
  (b) sharpening scabbard

SETS, BARBECUE, having NOT less than six steak knives and ANY of 
the following:
  (a) scraper;
  (b) tongs;
  (c) carving knife;
  (d) wooden block

SETS, KNIFE, including stainless steel knives and ANY of 
the following:
  (a) bone saw;
  (b) shears;
  (c) sharpener;
  (d) cutting board;
  (e) gloves

FILLET KITS, containing stainless steel knives and NOT less 
than two of the following:
  (a) stainless steel scissors;
  (b) sharpener;
  (c) gloves;
  (d) cutting board;
  (e) carry case

SETS, KITCHEN KNIFE, stainless steel, including knives, with OR
 without ANY of the following:
   (a) sharpening steel;
   (b) fork;
   (c) kitchen shears;
   (d) knife block

SETS, KNIFE KITCHEN, stainless steel, having BOTH of the following:
   (a) minimum of two (2) knives;
   (b) having ANY of the following:
           (i) spatula;
          (ii) potato peeler;
         (iii) sharpening steel;
          (iv) carving fork

KNIVES, TABLE, unplated

KNIVES, TABLE, stainless steel, unplated, with OR without a 
knife block AND/OR plastic handles

KNIVES, having handles, being ANY of the following: 
  (a) slicers; 
  (b) filleting knives;
  (b) boning knives

KNIVES, having handles, being EITHER of the following: 
  (a) butchers' knives;
  (b) slaughtermen's knives

KNIVES, KITCHEN, having stainless steel blades AND plastic 
handles, being ANY of the following:
  (a) bread knives;  
  (b) utility knives;
  (c) cooks knives;
  (d) santoku knives

PARING KNIVES, having stainless steel blades AND plastic handles

KNIVES, KITCHEN, stainless steel

KNIVES, being EITHER of the following:
   (a) display knives, having ALL of the following:
         (i) decorated handle;
        (ii) blunt blade;
       (iii) blade of steel of EITHER 430 or 420 J2 grade;
   (b) snap-off cutters

BLADES, trimming knife, replaceable

BLANKS, knife blade, being goods classified under subheading
 8211.94.10, OTHER THAN blanks for table knives
   For the purposes of TC 8633550 blanks are blades which have
   NOT been subjected to ANY of the following:
     (a) polishing;
     (b) sharpening;
     (c) branding;
     (d) handle fitting;
     (e) tempering

BARBECUE SETS, stainless steel, comprising at least three (3) of
 the following:
   (a) fork;
   (b) tongs;
   (c) spatula;
   (d) cleaning brush;
   (e) corn cob holders;
   (f) salt and pepper shakers;
   (g) skewers

SETS, CUTLERY, UNPLATED, having two OR more of ANY of the following
 OR any combination of the following:
   (a) knives;
   (b) forks;
   (c) spoons

SETS OF UNPLATED IMPLEMENTS, consisting of ALL of the following:
   (a) knives;
   (b) forks;
   (c) spoons;
   (d) spatula;
   (e) salad cutlery;
   (f) ladles;
   (g) sugar tongs;

SETS, UNPLATED IMPLEMENT, stainless steel, comprising BOTH of
 the following:
   (a) minimum of three (3) knives;
   (b) having at least four (4) of the following:
            (i)  carving fork;
           (ii)  spatula;
          (iii)  sharpening steel;
           (iv)  potato peeler;
            (v)  lemon decorator;
           (vi)  lemon zester;
          (vii)  tying OR larding needles;
         (viii)  fish knife;
           (ix)  oyster knife;
            (x)  shears;
           (xi)  apple corer;
          (xii)  cleaver;
          (xiii) icing funnel;
          (xiv)  potato baller and/OR melon baller

SETS, CHEESEBOARD, consisting of ALL of the following:
  (a) wooden cheeseboard incorporating a pull-out side draw;
  (b) NOT less than three cheese knives;
  (c) cheese fork

SETS, BARBECUE, including NOT less than ANY two of the following:
  (a) tongs;
  (b) multipurpose utensil;
  (c) scraper;
  (d) brush

SETS, BARBECUE, comprising BOTH of the following:
  (a) multi-purpose lifting tool;
  (b) tongs

SETS, CARVING, comprising ALL of the following:
  (a) knife;
  (b) fork;
  (c) board

SETS, KITCHEN TOOLS, comprising NOT less than ANY two of the 
following:
  (a) skimmer;
  (b) ladle;
  (c) spaghetti server

SETS, UNPLATED IMPLEMENT, stainless steel, comprising BOTH of
 the following:
   (a) minimum of three (3) knives;
   (b) having at least four (4) of the following:
            (i)  carving fork;
           (ii)  spatula;
          (iii)  sharpening steel;
           (iv)  potato peeler;
            (v)  lemon decorator;
           (vi)  lemon zester;
          (vii)  tying OR larding needles;
         (viii)  fish knife;
           (ix)  oyster knife;
            (x)  shears;
           (xi)  apple corer;
          (xii)  cleaver;
          (xiii) icing funnel;
          (xiv)  potato baller and/OR melon baller

SETS, CARVING, stainless steel, comprising ALL of the following:
   (a) knife;
   (b) fork;
   (c) sharpening steel

HOUSEHOLD TOOLS, unplated, being ANY of the following:
 (a) spoons;
 (b) forks
 (c) fish knives;
 (d) butter knives;
 but NOT including household tool souvenirs

UTENSILS, barbecue, multi-purpose, incorporating ANY four of the
 following features:
   (a) fish splicer (spatula);
   (b) plate scraper;
   (c) cutting edge;
   (d) meat tenderising prongs;
   (e) bottle opener;
   (f) fat drainer

CAKE/PIE SERVERS, unplated

KNIVES, fish or butter, unplated

TONGS, food serving

SKEWERS, BARBECUE, stainless steel

HOUSEHOLD TOOLS, unplated, being EITHER of the following:
   (a) ladles;
   (b) skimmers

HOUSEHOLD IMPLEMENTS, unplated, being ANY of the following:
   (a) spoons;
   (b) forks;
   (c) fish knives;
   (d) butter knives

FORKS OR SPOONS, TABLE, unplated

BARBECUE SET, having BOTH of the following:
  (a) skewers;
  (b) holding rack

PALLET KNIVES, CAKE DECORATING

KITCHENWARE, stainless steel AND plastic, being combination 
serving spoon and tong

TABLEWARE AND/OR KITCHENWARE, being stainless steel AND plastic 
tongs

SCOOPS, BBQ

UTENSILS, being EITHER of the following:
  (a) corn holders;
  (b) BBQ cleaning scrapers

UTENSILS, being ANY of the following:
  (a) spatulas;
  (b) spaghetti servers;
  (c) turners