Tariff Concession Orders

BARS AND/OR RODS AND/OR PROFILES, copper

PROFILES, brass, with OR without a thermal break

BRASS BARS, round and/or hexagonal, having a maximum 
dezincification of 50 microns in accordance with ISO 6509

BARS AND/OR RODS AND/OR PROFILES, brass

COPPER-ALUMINIUM (aluminium-bronze) bars and rods, certified
 to specification DGS1043 grades 1 and 2

BARS AND RODS, beryllium-copper

ROD, welding, copper-nickel, to AWS specification A5.7 class
 ER Cu Ni

WIRE OR ROD, refined copper, coiled, Electrolytic Tough Pitch 
(ETP), having ALL of the following:
  (a) NOT less 99.78% by weight of copper;
  (b) oxygen content NOT less than 50 ppm;
  (c) diameter NOT less than 6.0 mm and NOT greater than 11.0 mm

WIRE, solder plated, having ALL of the following:
  (a) core wire NOT less than 99.90% Cu;
  (b) wire thickness NOT less than 0.05 mm and NOT greater than 
      0.50 mm;
  (c) wire width NOT less than 1.00 mm and NOT greater than 
      6.00 mm;
  (d) thickness of solder plate NOT less than 10 microns and NOT 
      greater than 40 microns

WIRE, brass, whether or not galvanic zinc coated, but NOT
 otherwise coated, having BOTH of the following:
   (a) OD NOT exceeding 0.301 mm;
   (b) tolerance + or - 1 micron

BRASS WIRE, C 2600 Grade, diameters NOT less than 1.2 mm and NOT
greater than 9 mm

WIRE, welding, copper nickel, to AWS
 Specification A5.7, Class ER Cu Ni

WIRE, nickel silver

WIRE, DEOXIDISED COPPER ALLOY 189, MIG WELDING

WIRE, deoxidised copper

WIRE, phosphor bronze

WIRE, welding, being EITHER of the following:
   (a) silicon bronze;
   (b) aluminium bronze

WIRE, alloy, containing aluminium, copper and nickel

COPPER COIL REFINED, being EITHER of the following:
   (a) any width exceeding 100 mm, having a thickness greater than
       1.5 mm;
   (b) having a width exceeding 599 mm, with a thickness greater than
       0.15 mm but NOT exceeding 1.5 mm

COPPER PLATES AND/OR SHEETS AND/OR STRIP, thickness greater than
 0.15 mm

REFINED COPPER, sheets and plates having a thickness exceeding
 0.15 mm, but NOT including ANY of the following:
   (a) goods having a width of 200 mm or less combined with a maximum
       width to thickness ratio of 50:1;
   (b) goods having a width of 260 mm or less combined with a maximum
       width to thickness ratio of 25:1

COPPER PLATES AND/OR SHEETS AND/OR STRIP, thickness greater than
 0.15 mm

MOULD PLATES AND/OR CENTRE BLOCKS, SLAB CASTER

PLATES AND/OR SHEETS AND/OR STRIP, of copper-zinc base alloys,
 thickness greater than 0.15 mm

BRASS SHEETS AND PLATES, having a thickness exceeding 0.15 mm, but
 NOT including goods having a width of 200 mm or less combined with
 both a maximum width to thickness ratio of 40:1 and length of 10 m
 or less

PLATES AND/OR SHEETS AND/OR STRIP, of copper-zinc base alloys,
 thickness greater than 0.15 mm

PLATES AND/OR SHEETS AND/OR STRIP, of copper-tin base alloys,
 thickness greater than 0.15 mm

BRONZE SHEETS AND PLATES, having a thickness exceeding 0.15 mm

PLATES AND/OR SHEETS AND/OR STRIP, of copper-tin base alloys,
 thickness greater than 0.15 mm

COPPER NICKEL SHEETS AND PLATES, having a thickness exceeding
 0.15 mm

PLATES AND/OR SHEETS AND/OR STRIP, of copper-nickel base alloys
 (cupro-nickel) OR copper-nickel-zinc base alloys (nickel silver),
 thickness greater than 0.15 mm

COPPER ALLOY, sheets and plates, having a thickness exceeding
 0.15 mm, but NOT including goods having a width of 200 mm or less
 combined with both a maximum width to thickness ratio of 40:1 and
 length of 10 m or less

STRIP, beryllium-copper

BLANKS, COIN, TOKEN OR MEDALLION

COIN BLANKS, aluminium bronze

PLATES AND/OR SHEETS AND/OR STRIP, copper alloy, thickness greater
 than 0.15 mm

COPPER FOIL, NOT backed, to a thickness NOT exceeding 0.15 mm

COPPER ALLOY (BRASS) FOIL, NOT backed, to a thickness NOT exceeding
 0.15 mm

STRIP, beryllium copper, having a thickness of 0.15 mm or less

GOLD SCHLAG (ALSO KNOWN AS IMITATION GOLD OR DUTCH METAL)

LAMINATES, copper clad

TUBES, copper, straight lengths, conforming to Australian 
Standard 1432-2004 (AS 1432-2004), having BOTH of the following:
  (a) outside diameter NOT less than 63 mm and NOT greater than 
      250 mm;
  (b) type A AND/OR B

TUBES, copper, level wound coil, having BOTH of the following:
  (a) outside diameter NOT less than 6 mm and NOT greater than
      25.4 mm;
  (b) wall thickness NOT less than 0.4 mm and NOT greater than
      2.03 mm

TUBES, COPPER, seamless, in coil form, having BOTH of the 
following:
  (a) integrally rolled inner grooved fins;
  (b) diameter NOT less than 9 mm and NOT greater than 16 mm

TUBING, Bourdon, conforming to BS 3127:1979, being brass 63/37
 Alloy, oval elliptic, supplied in straight lengths which when
 bent to a curve, tend to straighten under internal pressure

TUBING, BRASS, butt welded, oval section, solder coated, having
 ALL of the following:
   (a) height NOT less than 15.00 mm;
   (b) crown diameter NOT less than 2.00 mm;
   (c) end diameter NOT less than 1.80 mm;
   (d) wall thickness NOT less than 0.125 mm

BRASS TUBING, having ALL of the following:
  (a) outside diameter NOT less than 15.88 mm and NOT greater
      than 25.40 mm;
  (b) wall thickness NOT less than 1.88 mm and NOT greater than 
      2.65 mm;
  (c) lead content NOT less than 2.5% and NOT greater than 3.5%

TUBES, brass, oval hollow section, solder coated, having ALL of 
the following:
   (a) oval height outside diameter NOT less than 10.00 mm;
   (b) oval width outside diameter NOT less than 1.80 mm;
   (c) wall thickness NOT less than 0.125 mm

TUBES OR PIPES, brass, conforming to the American Society for 
Testing and Materials B111 C44300 (ASTM B111 C44300)

TUBING, aluminium brass, having ALL of the following:
  (a) grade American Society for Testing and Materials (ASTM) 
      B111 C-68700;
  (b) outside diameter NOT less than 12.7 mm and NOT greater
      than 38.1 mm;
  (c) wall thickness not less than 0.90 mm and NOT greater 
      than 2.03 mm

HOLLOWS, HEXAGONAL AND/OR OCTAGONAL, brass alloy

TUBING, copper nickel 90/10 Alloy, dia exceeding 90 mm

TUBES OR PIPES, 70/30 copper nickel alloy

CURPO NICKEL TUBES, having ALL the following specifications:
   (a) ASTM B111C706000 90/10 CuNi;
   (b) hard temper H55;
   (c) light drawn;
   (d) tensile 390 N/SQ mm;
   (e) elongation 20%;
   (f) hardness 96V; and
   (g) in ANY of the following sizes:
       (i) 6.35 OD x 0.56 mm wall;
      (ii) 7.93 OD x 0.56 mm wall;
     (iii) 9.53 OD x 0.7 mm wall;
      (iv) 12.70 OD x 0.91 mm wall;
       (v) 16.25 OD x 1.2 mm wall

FINNED TUBING, HEAT EXCHANGER, having ALL of the following:
  (a) cold-formed;
  (b) cupro-nickel alloy inner tube having a diameter NOT less
      than 15.5 mm;
  (c) aluminium alloy external fins having a diameter NOT less
      than 38 mm

TUBES OR PIPES, copper-nickel alloy, having ALL of the 
following:
  (a) copper composition NOT less than 65% and NOT greater than
      90%;
  (b) nickel composition NOT less than 5% and NOT greater than
      35%;
  (c) diameter NOT less than 5 mm and NOT greater than 1 620 mm

PIPES, copper-nickel alloy, having ALL of the following:
  (a) copper composition NOT less than 65% and NOT greater 
      than 90%;
  (b) nickel composition NOT less than 5% and NOT greater 
      than 35%;
  (c) diameter NOT less than 5 mm and NOT greater 
      than 330 mm

TUBES OR PIPES, copper-nickel, conforming to the American 
Society for Testing and Materials B111 C70600 (ASTM B111 
C70600), having an outside diameter NOT less than 38.1 mm and 
NOT greater than 152 mm

TUBES, SEAMLESS, 90/10 copper-nickel alloy, complying with 
Australian Standard 1569 (AS 1569), having ALL of the following:
  (a) grade 706;
  (b) temper 1/4 hard;
  (c) outside diameter NOT less than 12.7 mm and NOT greater
      than 38.1 mm;
  (d) wall thickness NOT less than 0.90 mm and NOT greater than
      2.03 mm

TUBING, copper nickel, having ALL of the following:
  (a) grade American Society for Testing and Materials (ASTM) 
      B111 C-70600 90/10CuNi;
  (b) outside diameter NOT less than 12.7 mm and NOT greater
      than 38.1 mm;
  (c) wall thickness not less than 0.90 mm and NOT greater than 
      2.03mm

TUBES, FINNED, COPPER-NICKEL ALLOY, COMPRESSOR HEAT EXCHANGER

TUBING, beryllium-copper

TUBES OR PIPES, copper alloy, having an iron composition by 
weight NOT less than 2%

TUBING, copper, solid drawn, finned, internally enhanced, having 
ALL of the following:
  (a) conforming to American Society of Mechanical Engineers 
      specification SB-75;
  (b) continuous integrally rolled fins;
  (c) NOT less than 40 fins per 25 mm;
  (d) length NOT less than 1 000 mm

KITS, GAS OR LIQUID REFRIGERANT, consisting of BOTH of the 
following:
  (a) foam insulated branched copper pipes;
  (b) reducer connectors

KITS, HEADER, gas OR liquid refrigerant, consisting of all of 
the following:
  (a) NOT less than six copper branches;
  (b) moulded insulation covers; 
  (c) foil duct tape

KITS, BRANCH, gas OR liquid refrigerant, consisting of all of 
the following:
  (a) NOT less than two copper branches;
  (b) reducer fittings;
  (c) moulded insulation covers; 
  (d) foil duct tape

FITTINGS, PRESS FIT TUBE, refined copper, complying with 
Australian Standard AS 3688-2005, having BOTH of the following:
  (a) ethylene propylene diene monomer (EPDM) rubber seal;
  (b) outside diameter NOT greater than 25 mm

FITTINGS, PRESS FIT TUBE, refined copper, complying with 
Australian Standard AS 3688-2005, having BOTH of the following:
  (a) ethylene propylene diene monomer (EPDM) rubber seal;
  (b) outside diameter exceeding 25 mm

FITTINGS, PRESS FIT TUBE, refined copper, having BOTH of the 
following:
  (a) hydrogenated nitrile butadiene rubber (HNBR) seal;
  (b) outside diameter NOT greater than 25 mm

FITTINGS, PRESS FIT TUBE, refined copper, having BOTH of the 
following:
  (a) hydrogenated nitrile butadiene rubber (HNBR) seal;
  (b) outside diameter exceeding 25 mm

FITTINGS, COMPRESSION, being refined copper olives

FITTINGS, TUBE, copper, press fit, having a diameter exceeding 
25 mm

FITTINGS, CAPILLARY, refined copper, internal diameter NOT 
greater than 26 mm

FITTINGS, cylindrical, pneumatic type, incorporating swivel
 capacity, but NOT including accessory adaptors or quick acting
 self sealing air line couplings

FITTINGS, pipe, to Specification BS 2871/CN102

FITTINGS, brass, fire brigade hose, "Storz" pattern

FITTINGS, PNEUMATIC/VACUUM TUBE, push in, having ALL of the
 following:
   (a) OD within the range of 4 mm to 12 mm;
   (b) operating air pressure NOT exceeding 1 800 kPa

FITTINGS, pipe, having the United States Screw Thread Standard NPT
 (National Pipe Thread)

FITTINGS, TUBE OR PIPE, copper alloy, having iron NOT less than 
2.09% and NOT greater than 2.61% of chemical composition

BASE FITTINGS, TAP OR SHOWER MIXER, threaded inlet AND outlet

FITTINGS, TUBE, threaded one end, NOT including garden hose 
fittings, having a tube outer diameter NOT exceeding 33 mm

TRANSITION PIPE FITTINGS, water OR gas, male OR female threaded 
adaptors, having ALL of the following:
  (a) brass inserts;
  (b) high density polyethylene spigot;
  (c) diameter NOT less than 40 mm and NOT greater than 155 mm;
  (d) length NOT less than 80 mm and NOT greater than 200 mm

TUBE FITTINGS, having barb connector

PRESS CONNECTORS, including ALL the following:
  (a) body composed of NOT less than 50% fibreglass reinforced 
      polyamide; 
  (b) polyoxymethylene clamping ring;  
  (c) sliding sleeve composed of NOT less than 35% fibreglass 
      reinforced polyamide;
  (d) threaded silicon bronze connector;
  (e) outlet AND/OR inlet diameter NOT less than 25 mm AND NOT
      greater than 63 mm

FITTINGS, PIPE TERMINATION, having ALL of the following:
  (a) nickel plated brass AND polyethylene material;
  (b) threaded male OR female ends;
  (c) double wall;
  (d) single piece construction

BOTTLE TRAPS, brass, with or without seal, having All of the 
following:
  (a) chrome plated outlet pipe length NOT less than 109 mm  
      and NOT greater than 341 mm;
  (b) chrome plated connection pipe;
  (c) Australian Standard 1589-2001 compliance

FITTINGS, dezincification resistant brass, but NOT including 
push-fit OR quick connect fittings, being compression 
sleeve connectors, having BOTH of the following:
   (a) complying with Australian Standard and New Zealand 
       Standard 2537.2-2011, (AS NZS 2537.2-2011);
   (b) outer diameter NOT less than 16 mm and NOT greater than 
       63 mm

FITTINGS, dezincification resistant brass, but NOT including 
push-fit OR quick connect fittings, being compression 
sleeve connectors, having BOTH of the following:
   (a) complying with Australian Standard and New Zealand 
       Standard 2537.5-2011, (AS NZS 2537.5-2011);
   (b) outer diameter NOT less than 16 mm and NOT greater than 
       63 mm

BRASS FITTINGS, GAS OVEN, being EITHER of the following:
  (a) injector nipples;
  (b) injector nipple kits, consisting of ALL of the following:
        (i) injector nipples;
       (ii) stickers;
      (iii) bags

FITTINGS, PRESS FIT TUBE, bronze, excluding quick connect OR 
push fit fittings, having BOTH of the following:
  (a) ethylene propylene diene monomer (EPDM) rubber seal;
  (b) outside diameter NOT greater than 25 mm

FITTINGS, PRESS FIT TUBE,  bronze, complying with Australian 
Standard AS 3688-2005, having BOTH of the following:
  (a) ethylene propylene diene monomer (EPDM) rubber seal;
  (b) outside diameter exceeding 25 mm

FITTINGS, PRESS FIT TUBE, bronze, excluding quick connect OR 
push fit fittings, having BOTH of the following:
  (a) hydrogenated nitrile butadiene rubber (HNBR) seal;
  (b) outside diameter NOT greater than 25 mm

FITTINGS, PRESS FIT TUBE, bronze, having BOTH of the following:
  (a) hydrogenated nitrile butadiene rubber (HNBR) seal;
  (b) outside diameter exceeding 25 mm

FITTINGS, GARDEN HOSE, brass, being ANY or a combination of two 
OR more of the following categories:
  (a) hose connectors;
  (b) tap adaptors;
  (c) tee sections;
  (d) hose couplings;
  (e) hose joiners;
  (f) flexible hose protectors;
  (g) sprinkler adaptors

KITS, Y BRANCH, consisting of ALL of the following:
  (a) NOT less than two copper Y branches;
  (b) reducer fittings;
  (c) moulded insulation covers

FITTINGS, PIPE OR TUBE, copper alloy, being lugged elbows with a 
screwed male extension at one end

COUPLINGS, TUBE AND/OR PIPE, copper alloy, having a captive nut 
at one end

FITTINGS, TUBE OR PIPE, copper-nickel alloy, press fit excluding 
quick connect, conforming to German Institute for 
Standardisation (DIN) standard 86019 and German Federal Office 
of Defence Technology and Procurement (BWB) Material Performance 
WL 2.1972, operating at hydrostatic pressures of 0 to 13 Bar, 
being ANY of the following:
  (a) couplings;
  (b) bends;
  (c) reducers;
  (d) T pieces;
  (e) adaptors;
  (f) flanges;
  (g) valves;
  (h) bulkhead and/or deck passings

FITTINGS, TUBE OR PIPE, copper-nickel, non-disconnecting, being 
ANY of the following:
  (a) connectors;
  (b) ends;
  (c) bulkhead pieces;
  (d) bulkhead stubs;
  (e) plugs;
  (f) sleeves;
  (g) nipples;
  (h) bushes;
  (i) reducers;
  (j) end caps;
  (k) bulkhead unions;
  (l) collars;
  (m) sockets;
  (n) adaptors

FITTINGS, TUBE OR PIPE, copper nickel, but NOT including quick 
connect fittings, being EITHER of the following:
(a) outlets;
(b) couplings

FITTINGS, TUBE, copper alloy, press fit, having a diameter 
exceeding 25 mm

FITTINGS, FIRE HOSE, copper alloy, instantaneous

FITTINGS, TUBE OR PIPE, copper nickel, excluding quick connect 
type fittings, being ANY of the following:
  (a) elbows;
  (b) flanges;
  (c) tees;
  (d) reducers;
  (e) bends;
  (f) saddles

FITTINGS, ELECTRICAL CONDUIT, brass OR brass and polyamide

BRASS FITTINGS, drop forge, extruded bar and/or section, taper 
male thread or parallel thread with washer seating faces being 
ANY of the following:
   (a) wall bayonet quick connect;
   (b) floor bayonet quick connect;
   (c) tee junction;
   (d) elbow;
   (e) socket;
   (f) olive;
   (g) couplings;
   (h) union connectors;
   (i) adapters;
   (j) nipples;
   (k) crosses;
   (l) compression or 45 degree flare fittings having a tube 
size NOT less than 3 mm and NOT greater than 26 mm;
   (m) twin ferrule compression (or swage type) elbows and/or 
tees having a tube size NOT less than 1 mm and NOT greater than 
51 mm
NOTE: This order does not include quick connect fittings in 
respect of items (c) to (m) inclusive

FITTINGS, TUBE OR PIPE, copper alloy, but NOT including quick 
connect fittings, being ANY of the following:
  (a) capillary;
  (b) olive;
  (c) screwed;
  (d) compression

FITTINGS, HOSE, brass, being EITHER of the following:
  (a) pneumatic couplers;
  (b) pneumatic interchange nipples

FITTINGS, CAMLOCK, bronze OR brass

BRASS FITTINGS, HOSE AND TAP, pneumatic, quick connect and release
 type, but NOT including garden hose fittings

BRAID, woven copper, resin impregnated, desoldering

WIRE, picture, stranded brass

WIRE, stranded, having a nominal diameter NOT greater 
than 0.5 mm

NAILS, having brass capped heads

NUTS, PIPE OR TUBE FITTING, copper alloy

SCREWS, wood, silicon bronze

FIXING POINTS, flat conductors, drop forged brass, having a 20 mm
 to 25 mm diameter ball type male connector, rated in non destructive
 testing to 20 kA/second

SHOWER HEADS, chrome plated

PLUGS, BATH AND/OR BASIN, brass, threaded, press down open 
AND close mechanism, with OR without EITHER of the following:
  (a) overflow apertures;
  (b) metal plating

ASSEMBLIES, HANDHELD AND OVERHEAD SHOWERHEADS, plastic AND/OR 
chrome plated brass, having BOTH of the following:
  (a) chrome plated brass shower rail;
  (b) metal AND/OR plastic flexible hose

SHOWERING SYSTEM, brass, hand held, comprising ALL of the 
following:
  (a) shower rail;
  (b) flexible metal hose;
  (c) shower head

SANITARY WARE, brass, being ANY of the following:
  (a) soap holders;  
  (b) tap spouts;
  (c) toilet roll holders

SHOWER HEADS, brass

STAVES, COPPER, BLAST FURNACE

STENCILS, alphabetical or numerical symbol, capable of being
 interlocked to compose a word or number

SUNDIALS, brass, Southern Hemisphere

SPRAYERS/NOZZLES, water, fire system

PINS, safety

BROOCH, NAME PLATE OR COSTUME JEWELLERY COMPONENTS, being ANY of
 the following:
   (a) pins;
   (b) pin backs;
   (c) stems

HANKS, jib

BROOCH COMPONENTS, cupro-nickel alloy, being ANY of the following:
   (a) pins;
   (b) pin backs;
   (c) stems

RUPTURE (BURSTING) DISCS, pressure system, whether or not
 incorporating vacuum supports

RINGS, nose, animal

BODKINS

RING MESH, bronze, having ALL of the following:
  (a) tin content NOT less than 5 percent;
  (b) ring diameter NOT less than 6 mm and NOT greater
      than 13 mm;
  (c) wire gauge NOT less than 0.5 mm and NOT greater 
      than 1.5 mm

PARTS, BUS BAR, ELECTRICAL CELL, copper, having a thickness NOT 
less than 31.5 mm, being ANY of the following:
  (a) end OR upper OR lower bus bars, having a length NOT less
      than 400 cm;
  (b) connector bus bars;
  (c) bus bar riser;
  (d) incomer bar bends

FIRE SPRINKLER HEADS, non-mechanical

STOVES, oil or spirit, single burner type, having a weight NOT
 exceeding 1.7 kg

FERRULES, WIRE ROPE

PARTS, BLAST FURNACE, OXYGEN OR ARGON LANCE, being ANY of the
 following:
   (a) tips;
   (b) bends;
   (c) reducers;
   (d) water deflectors;
   (e) nozzles

LANCE TIPS, OXYGEN NOZZLE

THIMBLES, brass, dressmakers" or tailors"

STOVES, oil or spirit, single burner type, having a weight NOT
 exceeding 1.7 kg

FERRULES, WIRE ROPE

PARTS, BLAST FURNACE, OXYGEN OR ARGON LANCE, being ANY of the
 following:
   (a) tips;
   (b) bends;
   (c) reducers;
   (d) water deflectors;
   (e) nozzles

LANCE TIPS, OXYGEN NOZZLE