Tariff Concession Orders

RAILS, crane, railway type, weight EXCEEDING 70 kg/m

RAILS, flat bottom, less than 20 kg/m

RAIL, having ALL of the following:
   (a) elevated guardrail configuration;
   (b) overall height 93 mm;
   (c) rail head height 38 mm;
   (d) neck height 40 mm;
   (e) base (foot) height 15 mm;
   (f) rail head width 80 mm;
   (g) base (foot) width 40 mm

GUIDE RAILS, having mass per meter GREATER THAN 70 kg/m, AND 
length LESS THAN 3 metres, with OR without mounting plates

RAIL TRACK SYSTEM, PAPERBOARD TRANSFER CAR, including ALL of the 
following:
  (a) rails with mounting brackets;
  (b) bearing plates;
  (c) stoppers

RAIL, CONSTRUCTION, conforming to European Standard EN 14811, 
being ANY of the following:
  (a) 73C1;
  (b) 75C1;
  (c) 76C1;
  (d) 105C1;
  (e) 310C1

RAIL, GROOVED, conforming to European Standard EN 14811, being 
ANY of the following:
  (a) RI53-10;
  (b) RI55NK;
  (c) 51R1;
  (d) 53R1;
  (e) 54G2;
  (f) 55G1;
  (g) 55G2;
  (h) 57R1;
  (i) 59R1;
  (j) 59R2;
  (k) Ri60NL;
  (l) 60R1;
  (m) 60R2;
  (n) 60R3;
  (o) 62R1;
  (p) 62R2;
  (q) 63R1;
  (r) 67R1

RAIL, grooved, being ANY of the following:
  (a) Ri57A;
  (b) 57A
  (c) Ri60R1;
  (d) Ri60;
  (e) Ri60-10;
  (f) 60Ri1;
  (g) 60R1

RAIL TRACK, comprising NOT less than 0.84% carbon

RAIL, ASYMMETRICAL POINTS, having ALL of the following:
   (a) tongue rail configuration;
   (b) base width 140 mm;
   (c) overall height 134 mm;
   (d) rail head width 74.5 mm;
   (e) rail head height 53 mm;
   (f) neck height 47.3 mm

DAMPERS, RAIL

CLIPS, CRANE RAIL

PIPES, cast iron, complying with European Standard EN877:1999 
(EN877:1999) having EITHER of the following:
  (a) internal coating of epoxy resin, outer coating of 
      acrylic primer;
  (b) internal coating of epoxy, outer coating of zinc and
      acrylic primer

LINE PIPE, seamless, stainless steel

LINE PIPE, carbon steel, seamless, having diameter NOT less than 
15 mm and NOT greater than 600 mm

LINE PIPE, seamless, circular cross section, complying with 
American Petroleum Institute Standard Specification 5L (API 5L), 
having EITHER of the following:
  (a) diameter less than 33.7 mm;
  (b) diameter exceeding 168.3 mm

LINE PIPE, seamless, to DNV-OS-F101

PIPES, STEEL, having a diameter NOT less than 65 cm

TUBES OR HOLLOW BARS (NOT BEING HONED TUBES), in straight lengths,
 ends plain, bevelled or threaded in accordance with ANY of the
 following tube, hollow bar or pipe material Specification options:
   (a) AS;
   (b) ASME;
   (c) ASTM;
   (d) BS;
   (e) DIN,
 but without further rework, having a length NOT less than four
 times the OD, as listed in THE TABLE:
                              THE TABLE
         Outside Dia                   Wall Thickness
   (a) NOT exceeding 219.08 mm         13.00 mm or greater but
                                       NOT exceeding 25.00 mm;
   (b) 219.08 mm or greater but        12.70 mm or greater but
       NOT exceeding 254.00 mm         NOT exceeding 50.80 mm;
   (c) 254.00 mm or greater but        19.05 mm or greater but
       NOT exceeding 323.85 mm         NOT exceeding 41.00 mm;
   (d) 323.85 mm or greater but        25.40 mm or greater but
       NOT exceeding 720.73 mm         NOT exceeding 75.00 mm

LINE PIPE, seamless, to Specification ASTM A333 Grade 6,
 having EITHER of the following:
   (a) OD exceeding 209.0 mm;
   (b) a WT of 12.5 mm or greater

DRILL PIPE, carbon alloy steel, having BOTH of the following:
  (a) tool joints attached at each end;
  (b) outside diameter NOT less than 139 mm

DRILL RODS, rotary drilling, having ALL of the following;
  (a) friction welded male AND/OR female fittings;
  (b) tensile and yield strengths exceeding 200 Newtons per
      square millimetre;
  (c) non-uniform internal bore;
  (d) not exceeding 167 millimetres in diameter

DRILL PIPE, seamless, non-alloy carbon steel, circular cross 
section, having EITHER of the following:
  (a) outside diameter (OD) NOT greater than 168.3 mm;
  (b) wall thickness (WT) NOT less than 16 mm

DRILL PIPE, conforming to American Petroleum Institute 
Specification 5D:2001 (API 5D:2001), having rotary connection 
attached

DRILL PIPES, having rotary connections attached, conforming to
 API Specification 7, being EITHER of the following:
   (a) conforming to API Specification 5D;
   (b) as listed in THE TABLE
                                  THE TABLE
         Outside Diameter                        Wall Thickness
     (i)  88 mm to 110 mm (both inclusive)       18 mm or greater;
    (ii) 110 mm to 120 mm (both inclusive)       20 mm or greater;
   (iii) 120 mm to 130 mm (both inclusive)       23 mm or greater

CASING AND/OR TUBING, STAINLESS STEEL, seamless

JOINTS, blast, being tubing threaded at both ends, in nominal
 lengths of 3.05 m or 6.10 m

CASING OR TUBING, oilwell (including casing or tubing with
 couplings), conforming to EITHER of the following:
   (a) API Specification 5CT;
   (b) Manufacturers" Material Specification CR9, CR13, CR22 or
       CR25 with other requirements to API Specifications 5CT,
 but NOT including EITHER of the following:
   (a) plain end casing or tubing;
   (b) casing with connectors

CASING OR TUBING, OIL OR GAS WELL, seamless, plain end, diameter NOT
 exceeding 140 mm

CASING OR TUBING, OIL AND/OR GAS WELL, seamless, conforming to 
American Petroleum Institute Specification 5CT (API 5CT), with 
OR without connectors

TUBES, cold drawn, seamless, to ANY of the following steel grades:
   (a) K1006;
   (b) K1016;
   (c) K1010;
   (d) K1020;
   (e) K1026,
 or ANY of the following tube specifications:
   (a) JIS G3445 STKM 11-20;
   (b) BS6323:Part 6:1982;
   (c) ASTM A513,
 and having BOTH of the following:
   (a) carbon content NOT less than 0.06% and NOT greater than 0.4%
       by weight;
   (b) OD NOT less than 6.4 mm and NOT greater than 203.2 mm

TUBES, carbon steel, in straight lengths, ends plain, bevelled or
 threaded, BUT without further rework, conforming to ASTM A179, cold
 drawn, seamless, having an OD NOT less than 6.4 mm and NOT greater
 than 203.2 mm

TUBES, seamless, cold drawn, in straight lengths, ends plain,
 bevelled or threaded, BUT without further rework, to specification
 DIN standard 2391: Part 2

TUBES, heat exchange and condenser, seamless, cold drawn, carbon
 steel, in straight lengths, ends plain, bevelled or threaded BUT
 without further rework, to specification ASTM A179/A 179M-88a

TUBES, seamless, hot finished, boiler and superheater, in straight
 lengths, ends plain, bevelled or threaded, BUT without further
 rework, to specification ASTM A210/A 210M-88a

TUBES OR HOLLOW BARS (NOT being honed tubes), in straight lengths,
 ends plain, bevelled or threaded in accordance with ANY of the
 following tube, hollow bar or Pipe Material Specification options:
   (a) AS;
   (b) ASME;
   (c) ASTM;
   (d) BS;
   (e) DIN,
 but without further rework, having a length NOT less than four
 times the OD, as listed in THE TABLE
                            THE TABLE
       Outside Diameter                Wall Thickness
   (a) NOT exceeding 219.08 mm         13.00 mm or greater but
                                       NOT exceeding 25.00 mm;
   (b) 219.08 mm or greater but        12.70 mm or greater but
       NOT exceeding 254.00 mm         NOT exceeding 50.80 mm;
   (c) 254.00 mm or greater but        19.05 mm or greater but
       NOT exceeding 323.85 mm         NOT exceeding 41.00 mm;
   (d) 323.85 mm or greater but        25.40 mm or greater but
       NOT exceeding 720.73 mm         NOT exceeding 75.00 mm

TUBES (NOT being honed tubes), seamless, having BOTH of the
 following:
   (a) elevated temperature properties conforming to
       Specification BS 3602 (1978) Grade 360 or AS 1835 TS 5;
   (b) OD NOT less than 1 250 mm OR a WT NOT exceeding 25 mm

TUBES, seamless, carbon steel, hot finished, in straight lengths,
 ends plain OR bevelled OR threaded, but without further rework, to
 specification DIN 1629

HOLLOW BARS, seamless, hot rolled or hot finished in straight
 lengths

PIPE MODULE, rigid steel frame, weight NOT less than 70 000 kg, 
including ANY of the following:
  (a) valves;
  (b) cable trays;
  (c) meters;
  (d) vessels

SPOOLS, SEAMLESS PIPE, non-alloy steel, hot finished, with OR 
without ANY of the following:
  (a) coated;
  (b) prepared ends;
  (c) fittings

BOILER PIPE, seamless, conforming to standard EN 102162-2, 
including ALL the following;
  (a) outside diameter 38.00 mm;
  (b) wall thickness 4.90 mm;
  (c) length greater than 5.0 metres,
For the purpose of this order tolerances allowable for the 
following specifications are: 
       (a) +/- 5% 
       (b) +/- 5%

BOILER PIPE, seamless, having ALL the following:
  (a) outside diameter NOT less than 45 mm and NOT greater 
      than 79 mm;
  (b) wall thickness NOT less than 6 mm and NOT greater than 
      6.5 mm;
  (c) length NOT less than 5 m;
  (d) complying with European Standard EN 10216-2;
  (e) outside diameter to wall thickness ratio NOT greater 
      than 12.2

BOILER PIPE, seamless, conforming to standard EN 102162-2, 
including ALL the following;
  (a) outside diameter 38.00 mm;
  (b) wall thickness 4.90 mm;
  (c) length greater than 5.0 metres,
For the purpose of this order tolerances allowable for the 
following specifications are: 
       (a) +/- 5% 
       (b) +/- 5%

DRILL TUBES, seamless, circular cross section, having BOTH of 
the following:
  (a) outside diameter (OD) NOT greater than 180 mm;
  (b) grouting holes

TUBES, alloy steel, in straight lengths, ends plain, bevelled
 or threaded in accordance with ANY of the following Pipe
 Material Specification options:
   (a) AS;
   (b) ASME;
   (c) ASTM;
   (d) BS;
   (e) DIN,
 but without further rework, containing NOT less than 12% by
 weight of chromium, having EITHER of the following:
   (a) OD NOT exceeding 105 mm and WT NOT less than 4.5 mm
       but NOT exceeding 25 mm;
   (b) OD NOT less than 105 mm and WT NOT exceeding 25 mm

TUBES, stainless steel, containing 12% or more chromium, OD NOT
 exceeding 3.175 mm

TUBES, seamless, circular cross section, stainless steel, to
 specification ASTM A269 or ASTM A213, cold drawn and annealed,
 whether or NOT surface finished, having BOTH of the following:
   (a) OD NOT exceeding 6.35 mm;
   (b) WT NOT exceeding 1.20 mm

TUBING, seamless stainless steel, duplex alloy S.A.F.2205 to ASTM
 A 789 UNS S31803, having an outside diameter less than 25mm

TUBES, cold reduced, stainless steel, carbon content NOT exceeding
 0.03%, to specifications ASTM A790, A789

SUBSEA DISTRIBUTION UNIT, including BOTH of the following:
  (a) tubes;
  (b) cables
with OR without ANY of the following:
          (i) compensation bladder;
         (ii) frame;
        (iii) support foundation;
         (iv) mudmat;
          (v) stabs;
         (vi) valve

TUBES OR PIPES, stainless steel, finned, seamless

TUBES OR PIPES, stainless steel, seamless

TUBES OR HOLLOW BARS (NOT being honed tubes), in straight lengths,
 ends plain, bevelled or threaded in accordance with ANY of the
 following tube, hollow bar or Pipe Material Specification options:
   (a) AS;
   (b) ASME;
   (c) ASTM;
   (d) BS;
   (e) DIN,
 but without further rework, having a length NOT less than four
 times the OD, as listed in THE TABLE:
                              THE TABLE
       Outside Dia                       Wall Thickness
   (a) NOT exceeding 219.08 mm           13.00 mm or greater but
                                         NOT exceeding 25.00 mm;
   (b) 219.08 mm or greater but          12.70 mm or greater but
       NOT exceeding 254.00 mm           NOT exceeding 50.80 mm;
   (c) 254.00 mm or greater but          19.05 mm or greater but
       NOT exceeding 323.85 mm           NOT exceeding 41.00 mm;
   (d) 323.85 mm or greater but          25.40 mm or greater but
       NOT exceeding 720.73 mm           NOT exceeding 75.00 mm

TUBES, alloy steel, in straight lengths, ends plain, bevelled
 or threaded in accordance with ANY of the following Pipe
 Material Specification options:
   (a) AS;
   (b) ASME;
   (c) ASTM;
   (d) BS;
   (e) DIN,
 but without further rework, containing NOT less than 12% by
 weight of chromium, having EITHER of the following:
   (a) OD NOT exceeding 105 mm and WT 4.5 mm or greater but
       NOT exceeding 25.0 mm;
   (b) OD NOT less than 105 mm and WT NOT exceeding 25 mm

TUBES, stainless steel, containing 12% or more chromium, OD NOT
 exceeding 3.175 mm

PIPES, stainless steel, seamless, bevelled OR plain ends

TUBING OR PIPING, seamless stainless steel, having extruded 
aluminium finning

PIPE SPOOLS, stainless steel, hot finished, 
with OR without ANY of the following:
  (a) coated;
  (b) bevelled AND/OR ground ends;
  (c) fittings

TUBING OR PIPING, seamless stainless steel, having extruded 
aluminium finning

TUBES OR PIPES, stainless steel, seamless

PIPE, seamless, ferritic alloy steel, cold drawn, in straight
 lengths, ends plain, bevelled or threaded BUT without further
 rework, to specification ASTM A335/A 335M-89a

TUBES, longitudinally finned, extruded

TUBES OR HOLLOW BARS, seamless, alloy steel, cold rolled or cold
 finished, in straight lengths

TUBES, seamless alloy steel, cold drawn, compliant with American 
Society for Testing and Materials Standard A519/4130 (ASTM 
A519/4130)

PIPE, seamless ferritic alloy steel, hot finished, in straight
 lengths, ends plain, bevelled or threaded BUT without further
 rework, to specification ASTM A335/A 335M-88a

TUBES, alloy steel, in straight lengths, ends plain, without
 further rework, to ANY of the following Material Specifications:
   (a) ASTM A213;
   (b) ASME A213;
   (c) BS 3059;
   (d) AS 1835,
 having ALL of the following:
   (a) chromium content, by weight, of 0.7% or greater but NOT
       exceeding 12.5%;
   (b) an OD of 30 mm or greater but NOT exceeding 127 mm;
   (c) WT NOT exceeding 12.5 mm

TUBES OR PIPES, seamless, tested and certified to EITHER of the
 following Specifications:
   (a) ASTM A200 Grade T5;
   (b) ASTM A335 Grade P5

TUBES, hot rolled, seamless alloy steel to specification DIN1629

DRILL RODS, ROTARY PERCUSSIVE ROCK DRILLING, hollow, threaded OR
 tapered, external cross-section dimension exceeding 52 mm

TUBES OR PIPES, seamless alloy steel, hot finished, to ASTM A519
 Grade 4140

DRILL STRING SECTIONS, THREADED, ROTARY PERCUSSIVE ROCK DRILLING,
 being ANY of the following:
   (a) hollow drill tube;
   (b) hollow bar and rod external cross section dimension exceeding
       52 mm, and a maximum internal dimension greater than one half
       of the maximum external cross section dimension

TUBES OR PIPES, seamless, conforming to EITHER of the following
 specifications:
   (a) SA-213 T22;
   (b) SA-335 P22

PIPE MODULES, rigid steel frame, including ANY of the following: 
  (a) valves; 
  (b) steel hoses; 
  (c) cable trays;
  (d) pipe fittings

PARTS, SINTER CRUSHER, being shafts with OR without sleeves

WELD TEST RINGS, OIL AND/OR GAS PRODUCTION, alloyed steel, 
whether OR not nickel clad, complying with ASTM International 
Standard A694M-16 (2016)

RODS, RAISE DRILL, alloy steel, integral

TUBES OR HOLLOW BARS, seamless, alloy steel, hot finished OR hot
 rolled, in straight lengths

LANCES, OXYGEN OR INERT GAS, ceramic coated

LINE PIPE, WELDED, complying with American Petroleum Institute 
Standard Specification 5L (API 5L), having external diameter 
exceeding 406.4 mm, whether OR not spooled, with OR without ANY 
of the following:
  (a) coated;
  (b) prepared ends;
  (c) fittings

LINE PIPE, longitudinally submerged arc welded, having a 
diameter exceeding 406.4 mm, whether or NOT spooled, with OR 
without ANY of the following:
  (a) coated;
  (b) bevelled ends OR straight ends;
  (c) fittings

LINE PIPE, TIE-IN SPOOL, SUBSEA, complying with standard DNV-GL-
ST-F101

LINE PIPE BENDS, OIL AND GAS, complying with standard DNV-ST-
F101

WELD TEST RINGS, OIL AND GAS, complying with DNVGL-ST-F101 
standard

LINE PIPE, OIL AND GAS, submerged arc welded, conforming to 
standard DNVGL-ST-F101 2017

LINE PIPE, submerged arc welded, to DNV-OS-F101

STEEL LINE PIPE, OIL AND/OR GAS WELL, ELECTRIC RESISTANCE 
WELDED, exceeding 406.4 mm external diameter, conforming to 
American Petroleum Institute Specification 5L (API 5L)

LINE PIPE, OIL AND GAS, stainless steel, welded, having an 
external diameter NOT less than 406.4 mm

LINE PIPE, OIL AND GAS PIPELINE, steel, having BOTH of the 
following:
  (a) diameter NOT less than 645 mm;
  (b) longitudinally welded

CONDUCTOR CASING, OILWELL, to API specification 5L, with OR
 without connectors, having BOTH of the following:
   (a) outside diameter exceeding 500 mm;
   (b) wall thickness exceeding 20 mm

CASING, OIL AND/OR GAS WELL, having BOTH of the following:
  (a) outside diameter NOT less than 500 mm;
  (b) wall thickness NOT less than 14 mm

TUBES, alloy steel, in straight lengths, ends plain, bevelled
 or threaded in accordance with ANY of the following Pipe
 Material Specification options:
   (a) AS;
   (b) ASME;
   (c) ASTM;
   (d) BS;
   (e) DIN,
 but without further rework, containing NOT less than 10% by
 weight of chromium, having EITHER of the following:
   (a) OD NOT less than 1 250 mm;
   (b) WT 5 mm or greater but NOT exceeding 25 mm

WELD TEST RINGS, complying with Offshore Standard for Submarine 
Pipeline Systems DNV-OS-F101

FLOATING PIPELINES, longitudinally welded, steel, including ALL 
of the following:
  (a) internal diameter NOT less than 900 mm;
  (b) wall thickness NOT less than 25 mm;
  (c) length NOT less than 12 metres and NOT greater than 
      20 metres;
  (d) steel ball joints OR flange couplings;
  (e) floats

PIPES, stainless steel, external diameter exceeding 406.4 mm, 
whether OR not spooled, with OR without ANY of the following:
  (a) coated;
  (b) prepared ends;
  (c) fittings

SPOOLS, PIPE, welded carbon steel, external diameter GREATER 
than 406.4 mm, with at LEAST two of the following:
  (a) coated;
  (b) prepared ends;
  (c) fittings

PIPES, stainless steel, external diameter greater than 406.4 mm

PIPES, circular cross-section, submerged arc-welded, having ALL 
of the following:
  (a) press-formed, hot vacuum rolled nickel clad carbon 
      steel plate;
  (b) steel plate grade complying with American Society for 
      Testing and Material Standards ASTM A516 Grade 70
      (ASTM A516 Grade 70);
  (c) nickel-lined with nickel cladding NOT less than 2.00 mm
      and NOT greater than 4 mm thickness;
  (d) wall thickness NOT less than 9.5 mm and NOT greater than 
      35.0 mm

PIPE MODULES, steel frame, being pipework fitted rigid 
framework, having BOTH the following:
  (a) length NOT less than 2.5 metres;
  (b) weight NOT less than 3 tonnes

PIPES, mild steel OR stainless steel, with OR without couplings, 
having BOTH of the following:
  (a) internal ceramic tile lining;
  (b) outside diameter greater than 406.4 mm

TUBES, stainless steel, straight seam welded, conforming to 
American Society of Testing and Materials Standards
A-312/A 312M - 09 (ASTM A-312/A 312M - 09) and 
A358/A 358M - 08a (ASTM A358/A 358M - 08a), having ALL of the 
following:
  (a) straight lengths;
  (b) ends plain or bevelled or threaded or grooved;
  (c) wall thickness (WT) NOT less than 4 mm;
  (d) containing NOT less than 10% by weight of chromium

WELD TEST RINGS, complying with Offshore Standard for Submarine 
Pipeline Systems DNV-OS-F101

PIPES, stainless steel, welded, having a circular cross section 
external diameter NOT less than 450 mm

MOTHER PIPES, whether OR not clad, complying with Det Norske 
Veritas Germanischer Lloyd Offshore Standard F101(DNVGL-ST-F101)

TIE-IN SPOOLS, SUBSEA, having longitudinally welded line 
pipe, complying with Det Norske Veritas Offshore Standard F101 
(DNV-OS-F101), with OR without ANY of the following:
  (a) anodes;
  (b) coating AND/OR cladding AND/OR lining;
  (c) bends;
  (d) crosses;
  (e) flanges;
  (f) elbows;
  (g) tees;
  (h) reducers;
  (i) protective casings

LINE PIPE, High Frequency Welded (HFW), duel layer fusion bonded 
epoxy coated, complying with American Petroleum Institute 
Standard Specification 5L (API 5L), having ALL of the following:
  (a) steel AND pipe grade X65M;
  (b) product specification PSL2;  
  (c) diameter being EITHER of the following: 
        (i) NOT exceeding 55 mm;
       (ii) exceeding 168.3 mm

LINE PIPE, ELECTRIC RESISTANCE WELDED (ERW), complying with 
American Petroleum Institute Standard Specification 5L (API 5L) 
and International Standard 3183,(ISO 3183), having a diameter 
exceeding 168.3 mm

LINE PIPE, complying with DNV-OS-F101

CASING PATCHES, stainless steel, with hydrogenated nitrile outer 
skin

TUBING, electrical resistance welded, coiled OR in spools, having
 BOTH of the following:
   (a) minimum continuous length of 2 000 m;
   (b) minimum OD of 31 mm

CASING, OIL AND/OR GAS WELL, electric resistance welded, 
conforming to American Petroleum Institute Specification 5CT 
(API 5CT), with OR without connectors

TUBING, electrical resistance welded, coiled OR in spools, having
 BOTH of the following:
   (a) minimum continuous length of 2 000 m;
   (b) minimum OD of 31 mm

TUBES, cold drawn, welded, to specification ASTM A513,
 having BOTH of the following:
   (a) OD NOT less than 203.2mm and NOT greater than 306.0mm;
   (b) carbon content NOT less than 0.06% and NOT greater than
       0.4% by weight

PIPES, lance, oxygen calorised and ceramic coated

TUBES, welded, complying with Japanese Industrial Standard G3445 
STK11A (JIS G3445 STKM11A), having an outside diameter NOT 
greater than 12 mm

MINING PIPES, rotary, quick connect, having ALL of the following:
  (a) painted carbon steel body, outside diameter NOT LESS than
      406 mm AND inside diameter NOT LESS than 314 mm;
  (b) male AND/OR female couplings;
  (c) length NOT LESS than 10 200 mm;
  (d) pressure rating NOT LESS than 180 Bar;
  (e) torque rating NOT less than 135 kNm;
  (f) pullback rating NOT less than 500 tonnes

WELD TEST RINGS, OIL AND/OR GAS PIPELINE, complying with 
standard DNV(Det Norske Veritas)-ST-F101 Submarine Pipeline 
Systems (2017) AND/OR DNVGL(Det Norske Veritas Germanischer 
Lloyd)-ST-F101 Submarine Pipeline Systems (2017)

TUBES, cold drawn, welded, stress relieved, to DIN specification
 2393, having ALL of the following:
   (a) outside diameter of 15 mm to 22 mm;
   (b) inside diameter of 13 mm to 19 mm;
   (c) wall thickness of 1 mm to 1.6 mm

ROLLER TUBES, galvanised steel, round, having ALL of the 
following:
  (a) one OR more keyways;
  (b) keyway height NOT less than 7.5 mm and NOT greater
      than 12.5 mm;
  (c) wall thickness NOT less than 0.8 mm and NOT greater
      than 1.5 mm;
  (d) external diameter NOT less than 43 mm and NOT greater
      than 125 mm

PIPES, circular cross-section, submerged arc-welded, having ALL 
of the following:
  (a) press-formed, hot vacuum rolled nickel clad carbon 
      steel plate;
  (b) steel plate grade complying with American Society for 
      Testing and Material Standards ASTM A516 Grade 70
      (ASTM A516 Grade 70);
  (c) nickel-lined with nickel cladding NOT less than 1.00 mm 
      and NOT greater than 4.00 mm thickness;
  (d) wall thickness NOT less than 9.5 mm and NOT greater than 
      35.0 mm

PIPE MODULES, rigid steel frame, having flanged pipework, pipe 
diameter NOT greater than 450 mm

COILED TUBING, OIL AND GAS WELL, whether OR not on spools AND/OR 
reels

PIPES, mild steel, with OR without couplings, having BOTH of the 
following:
  (a) internal ceramic tile lining;
  (b) outside diameter less than 406.4 mm

PIPES, welded steel, multilayer, having ALL of the following:
  (a) steel inner service pipe;
  (b) polyurethane foam insulation incorporating copper wires; 
  (c) high density polyethylene outer casing

TUBES, welded, complying with Japanese Industrial Standard G3445 
STK11A (JIS G3445 STKM11A), having an outside diameter NOT 
greater than 12 mm

TUBES, WELDED, non alloy steel, being EITHER of the following:
   (a) single wall resistance welded to specification SAE J526,
       having ALL of the following:
           (i) carbon content NOT greater than 0.13%;
          (ii) outside diameter NOT greater than 11.50 mm;
         (iii) wall thickness NOT less than 0.5 mm and NOT greater
               than 1.0 mm;
   (b) double wall copper brazed to specification SAE J527,
       having ALL of the following:
           (i) carbon content NOT greater than 0.13%;
          (ii) outside diameter NOT greater than 13 mm;
         (iii) wall thickness NOT less than 0.5 mm and NOT greater
               than 1.0 mm

TUBES, cold drawn, welded, stress relieved, to DIN specification
 2393, having ALL of the following:
   (a) outside diameter of 15 mm to 22 mm;
   (b) inside diameter of 13 mm to 19 mm;
   (c) wall thickness of 1 mm to 1.6 mm

TUBES, alloy steel, in straight lengths, ends plain, bevelled
 or threaded in accordance with ANY of the following Pipe
 Material Specification options:
   (a) AS;
   (b) ASME;
   (c) ASTM;
   (d) BS;
   (e) DIN,
 but without further rework, containing NOT less than 12% by
 weight of chromium, having EITHER of the following:
   (a) OD NOT exceeding 105 mm and WT 4.5 mm or greater but NOT
       exceeding 25.0 mm;
   (b) OD NOT less than 105 mm and WT NOT exceeding 25 mm

TUBES, stainless steel, longitudinally welded, having BOTH of the
 following dimensions:
   (a) an OD 105 mm or greater but NOT exceeding 220 mm;
   (b) a WT 1.50 mm or greater but NOT exceeding 5.00 mm

TUBES OR PIPES, stainless steel, to specification UNS S31803, having
 chemical composition by weight of ALL the following:
   (a) carbon       :  0.030% maximum;
   (b) manganese    :  2.00% maximum;
   (c) phosphorus   :  0.030% maximum;
   (d) sulphur      :  0.020% maximum;
   (e) silicon      :  1.00% maximum;
   (f) chromium     :  21.00 - 23.00% both inclusive;
   (g) nickel       :  4.50 - 6.50% both inclusive;
   (h) nitrogen     :  0.03 - 0.20% maximum;
   (i) molybdenum   :  2.50 - 3.50% both inclusive

DIMPLE TUBES, heat exchanger, stainless steel

PIPES, stainless steel, with OR without couplings, having BOTH 
of the following: 
(a) internal ceramic tile OR sleeve lining; 
(b) outside diameter less than 406.4 mm

PIPES, stainless steel, welded, whether OR not spooled, with OR 
without ANY of the following:
  (a) coated;
  (b) prepared ends;
  (c) fittings

HYDRAULIC CONTROL LINES, OIL AND/OR GAS WELL, on spools OR 
reels, including ALL of the following:
  (a) NOT less than 2 stainless steel Grade 825 alloy tubes;
  (b) tube wall thickness NOT greater than 1.26 mm;
  (c) tube outer diameter NOT greater than 6.40 mm;
  (d) fluorinated ethylene propylene protective cover

TUBES AND/OR PIPES, stainless steel, laser welded seam, having 
an outside diameter NOT less than 15 mm and NOT greater than  
108 mm, having ALL the following:
  (a) material grade EN 1.4401;
  (b) dimension AND dimensional tolerances in accordance to 
      EN 10312 - Series 2;
  (c) surface roughness Ra NOT exceeding 1.6 micrometres; 
  (d) inspection certificate in compliance with EN 10204 type 3.1

TUBES OR PIPES, welded, stainless steel in accordance with 
EN10217-7TC1 OR EN 10296-2, having an outer diameter exceeding 
18.0 mm and NOT exceeding 1 012.0 mm

PIPE MODULES, rigid steel frame, having flanged pipework, pipe 
diameter NOT greater than 450 mm

PIPES, stainless steel, press fit, having ALL of the following:
  (a) ethylene propylene diene (EPDM) rubber seal;
  (b) stainless steel OR gunmetal press connector;
  (c) outside diameter NOT less than 12 mm and NOT greater than
      108 mm

HYDRAULIC CONTROL LINES, OIL AND/OR GAS WELL EQUIPMENT, wound on 
spools OR reels, including BOTH of the following:  
  (a) NOT less than 2 stainless steel pipes, having BOTH of the 
      following:
        (i) pipe wall thickness NOT greater than 1.36 mm;
       (ii) pipe outer diameter NOT less than 5.70 mm and NOT
            greater than 6.90 mm,
  (b) ethylene tetrafluoroethylene (ETFE) protective cover

TUBES OR PIPES, stainless steel, longitudinal welded, in 
straight lengths, conforming to EITHER of the following 
specifications:
  (a) American Society for Testing and Materials (ASTM) 
      specifications A249 OR A268 OR A269 OR A270 OR A554 OR 
      A688 OR A789;
  (b) Australian Standard 1528 (AS 1528)

TUBES OR PIPES, stainless steel, welded, in straight lengths, 
conforming to ANY of the following American Society for 
Testing and Materials (ASTM) specifications:
  (a) A312;
  (b) A358;
  (c) A409;
  (d) A778;
  (e) A790;
  (f) A813;
  (g) A814;
  (h) A928;
  (i) A999
TUBES or PIPES, stainless steel, welded, in straight lengths, 
conforming to any of the following ASTM (American Society for 
Testing and Materials) specifications:
   A312, A358, A409, A778, A790, A813, A814, A928 or A999.
 specifications:
   A312, A358, A409, A778, A790, A813, A814, A928 or A999.

PIPES, stainless steel, having ALL of the following:
  (a) outside diameter NOT less than 10.3 mm and NOT greater 
      than 406.4 mm;
  (b) wall thickness NOT less than 1.24 mm and NOT greater than 
      33.32 mm;
  (c) compliance with American Society for Testing and Materials
      standards Designations: ASTM A269-10 OR
      ASTM A312/A312M - 11 OR ASTM A554-13

TUBES AND/OR PIPES, stainless steel, longitudinal welded, rolled 
seam, having ALL of the following:
  (a) outside diameter NOT less than 10 mm and NOT greater than 
      219 mm;
  (b) wall thickness NOT less than 1 mm and NOT greater than
      2.6 mm;
  (c) conforming to American Iron and Steel Institute
      specifications 304 OR 316L  (AISI 304 OR AISI 316L)

TUBES, ERW, aluminized, type JIS G3445, having ALL of the following:
   (a) 12.7 mm OD;
   (b) 1.6 mm WT;
   (c) 5 700 mm mill length

WELD TEST COUPONS, OIL AND/OR GAS PIPELINE, including ALL of the 
following:
  (a) length NOT less than 900 mm;
  (b) internal diameter being EITHER of the following:
         (i)  168.3 mm +/? 5%;
        (ii) 355.6 mm +/? 5%

COILED TUBING, welded alloy steel, whether OR not on spools 
AND/OR reels, including ALL of the following:
  (a) yield strength NOT less than 600 MPa and NOT greater than
      700 MPa;
  (b) tensile strength  NOT less than 700 MPa and NOT greater 
      than 800 MPa;
  (c) internal yield pressure capacity NOT less than 60 MPa and  
      NOT greater than 200 MPa;
  (d) chemical composition by weight of ALL of the following:
           (i) carbon content NOT less 0.10% and NOT greater 
               than 0.20%;
          (ii) manganese content NOT less than 0.70% and NOT 
               greater than 0.90%;
         (iii) phosphorous content NOT less than 0.01% and NOT 
               greater than 0.02%;
          (iv) sulphur content NOT greater than 0.004%;
           (v) silicon content NOT less than 0.25% and NOT  
               greater than 0.35%;
          (vi) chromium content NOT less than 0.50% and NOT 
               greater than 0.60%;
         (vii) copper content NOT less than 0.20% and NOT 
               greater than 0.30%;
        (viii) nickel content NOT less than 0.15% and NOT 
               greater than 0.175%;
          (ix) molybdenum content NOT less than 0.095% and NOT 
               greater than 0.15%;
           (x) nitrogen content NOT greater than 0.005%;
          (xi) niobium content NOT less than 0.010% and NOT 
               greater than 0.016%;
         (xii) vanadium content NOT greater than 0.004%

COILED TUBING, OIL AND GAS WELL, whether OR not on spools AND/OR 
reels, having ALL of the following:
  (a) yield strength NOT less than 475 MPa and NOT greater than 
      800 MPa;
  (b) tensile strength NOT less than 440 MPa and NOT greater 
      than 850 MPa;
  (c) working pressure NOT less than 50 MPa and NOT greater than 
      210 MPa;
  (d) chemical composition by weight having ALL of the following:
           (i) carbon content NOT greater than 0.175%;
          (ii) manganese content NOT less than 0.50% and NOT 
               greater than 1.75%;
         (iii) phosphorous content NOT greater than 0.03%;
          (iv) sulphur content NOT greater than 0.007%;
           (v) silicon content NOT less than 0.075% and NOT 
               greater than 0.60%;
          (vi) chromium content NOT less than 0.20% and NOT 
               greater than 1.10%;
         (vii) nickel content NOT greater than 0.30%;
        (viii) copper content NOT greater than 0.45%;
          (ix) molybdenum content NOT less than 0.075% and NOT 
               greater than 0.35%;
           (x) aluminium content NOT greater than 0.075%

TUBES, rectangular, steel, including ALL of the following:
  (a) length NOT greater than 3 200 mm;
  (b) height NOT greater than 13 mm;
  (c) width NOT greater than 26 mm
  (d) thickness NOT greater than 1.5 mm

TUBES, square OR rectangular, electric resistance welded, 
complying with Australian/New Zealand Standard 1163:2009 (AS/NZS 
1163:2009), Grade C350L0 OR C450L0, having EITHER (a) OR (b) AND 
(c), as follows:
  (a) silicon content plus 2.5 times the phosphorus content
      NOT greater than 0.09%; 
  (b) silicon content greater than 0.14% and NOT greater than
      0.24%;
  (c) perimeter NOT less than 1 050 mm

TUBES, square OR rectangular, electric resistance welded, 
complying with Australian/New Zealand Standard 1163:2009 (AS/NZS 
1163:2009), Grade C350L0 OR C450L0, with a perimeter NOT less 
than 1 050 mm and having EITHER (a) OR (b) as follows:
  (a) silicon content plus 2.5 times the phosphorus content
      NOT greater than 0.09%; 
  (b) silicon content greater than 0.14% and NOT greater than
      0.24%

TUBES OR PIPES, stainless steel, square OR rectangular cross 
section, longitudinal welded in straight lengths, conforming to 
American Society for Testing and Materials A554 (ASTM A554)
specification

TUBES, square or rectangular, stainless steel to grade 1.4003, 
having BOTH of the following:   
  (a) width NOT greater than 105 mm; 
  (b) wall thickness NOT greater than 4 mm

TUBES, square, stainless steel, NOT less than 100 mm x 100 mm across
 the flat dimension

TUBES, rectangular, stainless steel, NOT less than 100 mm x 50 mm
 across the flat dimensions

TUBES, steel hot rolled, hot dip galvanised coated AND 
zinc passivated, being EITHER of the following:
  (a) hexagonal shape tubes, having ALL of the following:
         (i) length NOT less than 5 m and NOT greater than 5.8 m;
        (ii) width NOT less than 60 mm and NOT greater than 160  
             mm;
       (iii) steel thickness NOT less than 2.4 mm and NOT greater
             than 6 mm;
        (iv) yield strength NOT less than 250 N/mm2 and NOT 
             greater than 300 N/mm2;
         (v) tensile strength NOT less than 350 N/mm2 and NOT
             greater than 380 N/mm2;
        (vi) elongation NOT less than 33% and NOT greater 
             than 45%, 
  (b) three leaf clover shape tubes:
         (i) length NOT less than 5 m and NOT greater than 5.8 m;
        (ii) width NOT less than 33 mm and NOT greater than 120 
             mm;
       (iii) steel thickness NOT less than 3.9 mm and NOT greater
             than 9 mm;
        (iv) yield strength NOT less than 440 N/mm2 and NOT
             greater than 470 N/mm2;
         (v) tensile strength NOT less than 515 N/mm2 and NOT
             greater than 535 N/mm2;
        (vi) elongation NOT less than 25% and NOT greater than 
             35%

TUBES OR PIPES, stainless steel, longitudinal welded in straight 
lengths, conforming to American Society for Testing and 
Materials A554 (ASTM A554) specification, being ANY of the 
following cross sections:
  (a) oval;
  (b) slotted;
  (c) triangular;
  (d) D section;
  (e) tear drop

SLATS, ROLLER SHUTTER, stainless steel, including ALL of the 
following:
  (a) melamine resin filling;
  (b) thickness NOT greater than 14.5 mm;
  (c) height NOT greater than 65.5 mm,
with OR without end clips

FITTINGS, TUBE AND PIPE, rolled grooved, galvanised OR painted, 
with OR without gaskets, being ANY of the following:
  (a) elbows;
  (b) couplings;
  (c) reducers;
  (d) adaptors;
  (e) tees;
  (f) caps;
  (g) crosses;
  (h) reducing tees;
  (i) grooved flanges;
  (j) adaptor flanges

FITTINGS, ELBOWS AND/OR TEES, painted roll, grooved

COUPLINGS, CLAW, cast iron

FITTINGS, PIPE, cast iron, non-combustible, non-flammable, 
complying with European Standard EN 877:1999 (EN 877:1999)

FITTINGS, pipe, buttweld, socketweld or threaded, being EITHER of
 the following:
   (a) manufactured from ASTM A-216 WCB carbon steel castings;
   (b) manufactured from ASTM A-148 GR 60-90 steel castings

PIPE FITTINGS, POTABLE WATER AND GAS LINES, being EITHER of the
 FOLLOWING:
   (a) malleable cast iron couplings, incorporating a rubber seal
       and washer
   (b) tapped OR non tapped plugs incorporating a rubber seal

FITTINGS, pipe, B.S.P thread, made of galvanised malleable iron, to
 BS 1256, being ANY of the following:
   (a) elbows, 90 degrees, being EITHER, female to female, or male to
       female;
   (b) elbows, 45 degrees, being female to female;
   (c) elbows, 3 way;
   (d) elbows, reducing, 90 degrees;
   (e) tees, including 4 way, and reducing tees;
   (f) bush, hexagon;
   (g) caps;
   (h) crosses;
   (i) backnuts;
   (j) nipples, being ANY of the following:
         (i) hexagon;
        (ii) barrel;
       (iii) plain;
        (iv) reducing;
   (k) sockets including reducing sockets;
   (l) plugs, square head;
   (m) bends, 90 degrees, EITHER, male to female, or female to
       female;
   (n) bends, 45 degrees, male to female;
   (o) unions, EITHER, male to female, or female to female

FITTINGS, pipe, malleable cast iron

PIPE FITTINGS, roll grooved OR shouldered, being ANY of the 
following:
  (a) bolted couplings;
  (b) lever operated couplings

CLAW COUPLINGS, cast spheroidal graphite iron, zinc OR
plated, with OR without seal, being ANY of the 
following:
  (a) nominal size is NOT less than 9.5 mm and NOT greater than 
      76 mm;
  (b) male threaded connection;
  (c) female threaded connection;
  (d) hose tail end connection;
  (e) adaptors;
  (f) 3-way adaptors;
  (g) blank ends;
  (h) insertion tool

COUPLINGS, CLAW, cast stainless steel, with OR without locking 
pins, having ALL of the following:
  (a) diameter NOT less than 10 mm and NOT greater than 50 mm;
  (b) threaded male OR threaded female OR hose end connections;
  (c) bellows seals

FITTINGS, PIPE AND/OR TUBE, malleable cast iron, reducing OR non-
reducing, being ANY of the following:
  (a) tees;
  (b) combination tees and crosses;
  (c) corners;
  (d) crosses;
  (e) cross sets;
  (f) crossovers;
  (g) elbows;
  (h) flanges;
  (i) sockets;
  (j) side palms;
  (k) supports;
  (l) swivels;
  (m) couplings;
  (n) hooks;
  (o) collars;
  (p) collar plates;
  (q) hinges;
  (r) panel clips;
  (s) bases;
  (t) base plates

PIPE FITTINGS, roll grooved or shouldered, being ANY of the 
following:
  (a) elbows;
  (b) tees;
  (c) reducers;
  (d) end caps;
  (e) adapters

COUPLINGS, flexible, cast, stainless steel, having internal 
rubber gaskets

FITTINGS, CAMLOCK, stainless steel, being ANY of the following:
  (a) male sections and/or female sections;
  (b) plugs;
  (c) caps

FITTINGS, PIPE, ductile cast iron

FLANGES, PIPE, stainless steel, seamless

FLANGES, SUBSEA, having ANY of the following:
  (a) female weldneck;
  (b) seal ring;
  (c) hex nut;
  (d) ball fitting;
  (e) retaining ring;
  (f) stud bar;
  (g) hex socket countersunk head screw;
  (h) gasket retaining cam

FLANGES, STAINLESS STEEL PIPE, including internal alumina 
ceramic tiles

FITTINGS, VACUUM, stainless steel, operating pressure lower than
 133 x 0.0000001 MPa, being EITHER of the following:
   (a) couplings;
   (b) elbows

FITTINGS, TUBE, stainless steel, with OR without seals, being 
threaded bends

FITTINGS, seamless, stainless steel grade 316L, to specification
 ASTM 269 or ASTM 270, electropolished internally through entire
 length

FITTINGS, stainless steel, tube or pipe, buttweld, annealed,
 internally polished

BENDS, CROSSES, ELBOWS OR TEES, buttweld, stainless steel,
 conforming dimensionally to ANY of the following Specifications:
   (a) BS 1640;
   (b) ANSI B16.9;
   (c) ANSI B16.28

BENDS, SUBSEA, stainless steel

FITTINGS, TUBE OR PIPE, stainless steel in accordance with 
EN10253-3 OR EN10253-4, being ANY of the following:
  (a) elbows;
  (b) tees;
  (c) reducers;
  (d) collars;
  (e) end caps

FITTINGS, TEE, seamless, stainless steel, duplex

CONNECTOR HUBS, PIPE CLAMP, stainless steel, with OR without 
seals

REDUCERS, seamless, butt weld, stainless steel

RINGS, gasket or packing, to API Specification 6A, capable of
 operating at temperatures of 125 degrees C or greater

COUPLINGS, FLOW, OIL AND GAS WELL, stainless steel

FITTINGS, vacuum, stainless steel, helium leak tested, rated to
 lower than 133 x 10 -7 MPa, being ANY of the following:
   (a) plug;
   (b) cap;
   (c) gland;
   (d) body;
   (e) female nut;
   (f) male nut;
   (g) bodies, assembled with nuts and ferrules;
   (h) assemblies including ANY of the above

FITTINGS, pipe, forged stainless steel to specification type F 51
 ASTM UNS S 31803, having the surface descaled by turning

JOINTS, swivel, stainless steel, v-ring type, pressure rating
 greater than 6 800 KPa

COUPLINGS, camlocking, to material 316 stainless steel, 15 mm to 200
 mm, inclusive of both adaptors (male) and couplers (female).

FITTINGS, HOSE OR SPOOLABLE PIPE, stainless steel, threaded, 
double swage, with OR without o-ring seals

STAB PLATES, SUBSEA, male OR female, having NOT less than 8 
connection points, with OR without the following:
  (a) marine plug;
  (b) caps;
  (c) seal kits, consisting of at least TWO of the following: 
          (i) seals;
         (ii) valve stems;
        (iii) caps;
         (iv) springs;
          (v) rings

HOSE CONNECTERS, stainless steel alloy, having BOTH of the 
following
  (a) outside diameter NOT less than 3 mm and NOT greater 
      than 76 mm;
  (b) titanium content NOT less than 0.04% and NOT greater
      than 0.07%

CROSSOVER CONNECTORS, OIL AND/OR GAS WELL, subsea AND/OR 
surface, stainless steel

PUP JOINTS, OIL AND/OR GAS WELL TUBING, stainless steel, 
threaded, perforated, with OR without thread protectors

TUBE FITTINGS,  stainless steel, press tool connection, having 
ALL of the following:
  (a) ethylene propylene diene monomer (EPDM) rubber seals;
  (b) inside diameter NOT less than 15 mm and NOT greater than 
      108 mm;
  (c) with OR without one flanged OR screw OR plain end  
      connection;     
  (d) being ANY of the following:
      (i)   elbows, including back plated;
      (ii)  bends;
      (iii) sleeves

TUBE FITTINGS,  stainless steel, press tool connection, having 
ALL of the following:
  (a) ethylene propylene diene monomer (EPDM) rubber seals;
  (b) inside diameter NOT less than 15 mm and NOT greater than 
      108 mm; 
  (c) with OR without one flanged OR screw OR plain end 
      connection;  
  (d) being ANY of the following:
      (i)   couplings;
      (ii)  slip couplings;
      (iii) reducers;
      (iv)  tees;       
      (v)   union connectors;
      (vi)  adapters;
      (vii) end caps

PUP JOINTS, TUBING, OIL AND/OR GAS WELL, stainless steel, 
threaded, seamless, with OR without thread protectors, having an 
external working pressure rating of NOT less than 415 bar and 
NOT greater than 450 bar

COUPLINGS, FLOW, OIL AND/OR GAS WELL, stainless steel, having 
BOTH of the following:
  (a) threaded connections;
  (b) internal working pressure rating NOT less than 850 bar

CONNECTOR HUBS, PIPE CLAMP, stainless steel, with OR without 
seals

STAB PLATES, SUBSEA, stainless steel, having NOT less than 8 
connection points

COUPLINGS, PIPE, compression, stainless steel, having ALL of the 
following:
  (a) inside diameter NOT less than 200 mm;
  (b) single sealing sleeve consisting of a single sealing lip 
      on each side with progressive sealing effect;
  (c) single radial positioned locking system with 1 OR 2 OR 3
      screws

CONNECTORS, STAB, SUBSEA, male AND/OR female, with OR without 
protective caps

FITTINGS, DRAINAGE, Grade 316L stainless steel, being ANY of the 
following:
  (a) filter baskets;
  (b) removable water traps;
  (c) grates;
  (d) drainage bowls, having a diameter NOT greater than 300 mm

FITTINGS, TUBE, stainless steel, with OR without seals, being 
ANY of the following:
  (a) couplings having a diameter NOT greater than 200 mm;
  (b) reducers;
  (c) bends;
  (d) T junctions;
  (e) union connectors;
  (f) adapters

FITTINGS, PIPE AND TUBE, Grade 316L stainless steel, push fit, 
with or without seal, being ANY of the following:
  (a) pipe incorporating a socket;
  (b) bends;
  (c) pipe, having NOT less than 45 degree junctions and NOT 
      greater than 90 degree junctions;
  (d) double sockets;
  (e) "P" traps;
  (f) bottle trap;
  (g) eccentric increasers;
  (h) eccentric reducers;
  (i) access bends;
  (j) threaded adaptor

FITTINGS, DRAINAGE, Grade 316L stainless steel, being ALL 
of the following:
  (a) filter baskets;
  (b) removable water traps;
  (c) grates

FITTINGS, PIPE AND TUBE, stainless steel, being ANY of the 
following:
  (a) sealing rings;
  (b) bodies;
  (c) cap nuts;
  (d) weld cones;
  (e) flare adaptors

COUPLINGS, HOSE, quick connect, comprising ALL of the following:
  (a) male sections;
  (b) female sections;
  (c) lever rings

FITTINGS, COUPLING, HOSE, quick connect, being ANY of the 
following;
  (a) male sections; 
  (b) female sections;
  (c) lever rings;
  (d) male plugs;
  (e) female caps

FITTINGS, CAMLOCK, being ANY of the following:
  (a) male sections and/or female sections;
  (b) plugs;
  (c) caps

FLANGES, STEEL PIPE, including internal alumina ceramic tiles

FLANGE ADAPTERS, PIPE OR TUBE OR HOSE, carbon steel, with or 
without seal

FLANGES, PIPE, being ANY of the following:
  (a) weld neck flanges;
  (b) blind flanges;
  (c) spectacle blind flanges;
  (d) slip on flanges;
  (e) socket weld flanges;
  (f) threaded flanges;
  (g) bulkhead flanges

FLANGES, HOT FORGED, SEAMLESS, comprising ALL of the following:
       (a) inner diameter NOT less than 1 500 mm;
       (b) width NOT greater than 400 mm;
       (c) outer diameter NOT less than 2 000 mm

FITTINGS, TUBE, elbow, carbon steel, twin ferrule

FITTINGS, PIPE AND TUBE, including sealing rings, bodies, nuts and
 weld cones, having BOTH of the following:
   (a) compliance with pressure rating of either LL, L or S to
       DIN 2353;
   (b) interchangeability of the whole or any component of the
       fitting with other fittings or components which comply with
       the dimensional specifications set out in DIN 2353,
 but NOT including ANY of the following:
   (a) stainless steel fittings;
   (b) twin ferrule fittings

FITTINGS, pipe, steel, complying with standards BS1740 or AS3672

FITTINGS, TUBE, carbon steel, press fit, with OR without seals, 
being threaded bends having an internal AND/OR external zinc 
coating NOT greater than 8 micron

FITTINGS AND ADAPTORS, PIPE OR TUBE OR HOSE, carbon steel, with 
or without seal, being ANY of the following:
  (a) elbows, 90 degrees;
  (b) elbows, 45 degrees;
  (c) elbows, 3 way tees, being either male to female OR
      combinations of both;
  (d) tube sleeves;
  (e) bends, 90 degrees;
  (f) bends, 45 degrees

ELBOWS, threaded

JOINTS, insulating, monobloc or monolithic

FITTINGS, being ANY of the following:
   (a) elbows to ASTM Specification A234 WPB, having a dia less
       than 406.4 mm OD;
   (b) reducers to ASTM Specification A234 WPB, having BOTH
       diameters less than 406.4 mm OD;
   (c) elbows, reducers or tees to ASTM Specification A234 WP 11

FITTINGS, buttweld pipe, being ANY of the following:
   (a) to ASTM Specification A420 GRWPL6:
         (i) elbows, 45 degrees;
        (ii) elbows, 90 degrees, OD NOT exceeding 304.8 mm;
       (iii) reducers, eccentric;
   (b) to ASTM Specification A234 GRWP1:
         (i) elbows, 45 degrees or 90 degrees, OD NOT exceeding
             254 mm;
        (ii) reducers, eccentric, OD at larger end NOT exceeding
             254 mm

FITTINGS, buttweld, in accordance with Dimensional Specification
 MSS-SP75 and Material Specification API 5LX

FITTINGS, buttweld, to specifications BS1640 OR ANSI B16.9 OR
 ANSI B16.28, being ANY of the following:
   (a) bends, 30 degrees, 45 degrees, 50 degrees, 60 degrees,
       90 degrees OR 180 degrees, having an outside diameter between
       17 mm and 406.4 mm;
   (b) tees, equal OR reducing, having an outside diameter of
       406.4 mm OR less
 For the purposes of this order, ALL measurements have a tolerance of
 + OR - 5%

REDUCERS, buttweld, having a minimum outside diameter between 70 mm
 and 200 mm (+ or - 0.001%)

FITTINGS, buttweld, forged, integrally reinforced, contoured-insert
 vessel or piping branch connections, bore sizes 15 mm - 1 200 mm

HOT TAP ASSEMBLY, including tee, with OR without support 
foundation, including at least two of the following:
  (a) mud mat;
  (b) yoke;
  (c) pipe;
  (d) steel frame

TRANSITION FITTINGS, PIPE OR TUBE, butt fusion, having BOTH of 
the following:
  (a) carbon steel tubing coated with zinc AND/OR low density 
      polyethylene;
  (b) high density polyethylene spigot

CONNECTOR HUBS, PIPE CLAMP, carbon steel, with OR without seals

FITTINGS, PIPE AND/OR TUBE, butt weld, being caps of carbon 
steel to American Society of Testing and Materials Specification 
A234 Grade WPB (ASTM A234 Grade WPB)

FITTINGS, PIPE OR TUBE, butt-welded, forged steel, being 
reinforced and contoured connections

FITTINGS, PIPE AND/OR TUBE, butt weld, alloy steel, being end 
caps

FITTINGS, BUTTWELD, being ANY of the following:
  (a) bends;
  (b) crosses;
  (c) elbows;
  (d) reducers;
  (e) tees

CLOSURES, pressurised pipeline, hinged, quick release, diameter
 150 mm or greater, but NOT including screw top type closures

JOINTS, swivel, pressure rating over 40 MPa

COUPLINGS, casing or tubing, seamless to Specification API-5CT,
 section 8

FITTINGS, steel pipe, being EITHER of the following:
   (a) three lug wing nut unions, dia NOT exceeding 300 mm,
       minimum operating pressure 6.80 MPa;
   (b) hub clamp assemblies, consisting of ALL of the following:
         (i) clamp segments;
        (ii) hubs;
       (iii) seal ring

RINGS, gasket or packing, to API Specification 6A, capable of
 operating at temperatures of 125 degrees C or greater

COUPLINGS, pipe or hose, quick connect (or disconnect), comprising
 male and female ring lock couplings, hinged ring band snap lock
 and double lip gasket, to suit pipes and hoses having an OD of
 50 mm or greater

COUPLINGS, hose, having a working capacity of 206 MPa or greater

JOINTS, insulating, monobloc or monolithic

ELBOWS, socketweld, being ANY of the following:
   (a) 15 degrees;
   (b) 45 degrees;
   (c) 90 degrees ID exceeding 50.8 mm

COUPLINGS, SUCKER ROD, 12.7 mm to 28.6 mm (1/2" to 1 1/8")

NIPPLES, LANDING, SUB SURFACE FLOW CONTROL

GROUND CONES, FLEXIBLE METAL CONDUIT FITTING

FITTINGS, ON-LINE HYDRAULIC LINE TESTING, being couplers, adaptors
 OR stand pipes, working pressures up to 40 MPa in hose sizes 2 mm
 and 4 mm

FITTINGS, TUBE, carbon steel, twin ferrule

FITTINGS, PIPE, unthreaded, being ANY of the following:
   (a) joining rings having a diameter of 80 mm or greater but NOT
       exceeding 800 mm;
   (b) pressed bends of galvanised or mild steel in angles from 7.5
       degrees or greater but NOT exceeding 90 degrees and diameter
       of 80 mm or greater but NOT exceeding 400 mm;
   (c) straight ducting with fully rolled beaded edge having a
       diameter of 155 mm or greater but NOT exceeding 160 mm;
 but NOT including fittings of stainless steel

FITTINGS, STEEL, being EITHER of the following:
   (a) hose couplings having a female ACME coupling connection within
       the range of 44.45 mm to 82.55 mm (both inclusive);
   (b) adapters with male ACME connection within the range of
       44.45 mm to 82.55 mm (both inclusive)

FITTINGS, pipe and tube, including sealing rings, bodies, nuts and
 weld cones, having BOTH of the following:
   (a) compliance with pressure rating being either LL, L or S to
       DIN 2353;
   (b) interchangeability of the whole or any component of the
       fitting with other fittings or components which comply with
       the dimensional specifications set out in DIN 2353,
 but NOT including ANY of the following:
   (a) stainless steel fittings;
   (b) twin ferrule fittings

BRANCH CONNECTIONS, weld on type, complying with ALL the following
 standards:
   (a) ASTM A105;
   (b) ANSI B31-1 1980;
   (c) ANSI B16-9;
   (d) BS3351 1971

FITTINGS, pipe, high pressure, steel, complying with ALL the
 following standards:
   (a) ASTM A105;
   (b) ANSI B16.11;
   (c) BS3799

COUPLINGS, pipe or hose, quick connect (or disconnect), comprising
 male and female ring lock couplings, hinged ring band snap lock,
 to suit pipes and hoses having an OD of 50 mm or greater

FITTINGS, pipe and tube, metric, including sealing rings, bodies and
 nuts, to specifications DIN 2353 or DIN 3859 in ANY of the
 following sizes:
   (a) 4 mm;
   (b) 6 mm;
   (c) 8 mm;
   (d) 10 mm;
   (e) 12 mm;
   (f) 14 mm;
   (g) 15 mm;
   (h) 16 mm;
   (i) 18 mm;
   (j) 20 mm;
   (k) 22 mm;
   (l) 25 mm;
   (m) 28 mm;
   (n) 30 mm;
   (o) 35 mm;
   (p) 38 mm;
   (q) 42 mm;
   (r) 50 mm

COUPLINGS, PIPE, steel, quick connect, having ALL of the 
following: 
  (a) outside diameter NOT less than 406 mm;
  (b) inside diameter NOT less than 314 mm;
  (c) rated torque NOT less than 135 kNm;
  (d) rated tension NOT less than 500 tonnes;
  (e) male AND/OR female sections

PIPE FITTINGS, carbon steel, nylon 11 coating, restraint OR non-
restraint, being ANY of the following:
  (a) single bolt couplings;
  (b) double bolt couplings;
  (c) flange adaptors;
  (d) liners

FITTINGS, SUBSEA, steel, being pipeline collars

HUBS AND PUPS AND MOUNTING PLATES, VERTICAL CLAMP CONNECTION 
SYSTEM

CONNECTOR ACTUATING TOOL, SUBSEA FLOWLINE, having a clamp, with 
OR without EITHER of the following:
  (a) termination head;
  (b) hub

SUBSEA CONDUCTOR HOUSINGS, having valve units, with OR without 
plugs

FITTINGS, AIR BRAKE, steel, having ALL of the following:
  (a) working pressure NOT less than 1 030 kPa and NOT greater 
      than 1 380 kPa;
  (b) working temperature NOT less than minus 30 degrees Celsius
      and NOT greater than 80 degrees Celsius;
  (c) airflow NOT greater than 1 600 litres per minute 
      at 620.5 kPa

CLAMPS, PIPELINE, SUBSEA

FLOWLINE END TERMINATIONS, SUBSEA, with OR without ANY of the 
following:
  (a) anodes;
  (b) mud mats;
  (c) protective frames;
  (d) support bases

HAMMER UNIONS, lugged wing nut type, with OR without seals, 
including ANY of the following:
  (a) male AND/OR female sub sections;
  (b) plugs;
  (c) caps;
  (d) wing nuts AND/OR split nuts

CONNECTOR HUBS, PIPE CLAMP, carbon steel, with OR without seals

END CAPS, PRESSURE VESSEL

CONNECTORS OR COUPLINGS, CASING OR TUBING, OIL AND/OR GAS WELL, 
conforming to American Petroleum Institute Specification 5CT 
(API 5CT)

CROSSOVER CONNECTORS, OIL AND/OR GAS WELL EQUIPMENT, SUBSEA 
AND/OR SURFACE

COUPLINGS, CROSSOVER, OIL AND/OR GAS WELL EQUIPMENT, SUBSEA 
AND/OR SURFACE

COUPLINGS, PIPE, compression, hot dipped galvanised, having ALL 
of the following:
  (a) inside diameter NOT less than 30 mm;
  (b) single sealing sleeve consisting of a single sealing lip 
      on each side with progressive sealing effect;
  (c) single radial positioned locking system with 1 OR 2 OR  
      3 screws

FITTINGS, TUBE, carbon steel, with OR without seals, having an  
internal AND/OR external zinc coating NOT greater than 8 micron, 
being ANY of the following:
  (a) couplings having a diameter NOT greater than 200 mm;
  (b) reducers;
  (c) bends;
  (d) T junctions;
  (e) union connectors;
  (f) adaptors

FITTINGS, MULTILAYERED WELDED STEEL PIPE, being ANY of the 
following:
  (a) elbows;
  (b) joints;
  (c) reducers;
  (d) T fittings;
  (e) bends;
  (f) end caps

TERMINATION HEADS, subsea

FITTINGS AND ADAPTORS, PIPE OR TUBE OR HOSE, carbon steel, with 
or without seal, being ANY of the following:
  (a) reducing or enlarging bush, hexagon;
  (b) caps, solid or swivel;
  (c) crosses;
  (d) nipples, being ANY of the following:
          (i) hexagon;
         (ii) barrel;
        (iii) plain;
         (iv) reducing;
  (e) sockets, including reducing and enlarging;
  (f) plugs, square head or hex head or internal or external 
      hexagon;
  (g) unions;
  (h) tube welds or weld-on's;
  (i) tube compression and tube flared fittings

FITTINGS, ROOF DRAINAGE, galvanized steel, being ANY of the 
following:
  (a) rainwater outlets;
  (b) inclined outlets;
  (c) hoppers;
  (d) elbows;
  (e) s-curves;
  (f) hinged outlets;
  (g) pipe flaps
including sets of 2 or more of the above

FITTINGS, PIPE, forged, integrally reinforced, contoured-insert  
vessel or piping branch connections, having a bore size NOT less 
than 15 mm and NOT greater than 1 200 mm

CONNECTORS, HYDRAULIC HOSE, steel

FITTINGS, PIPE, being EITHER of the following:
  (a) hot tap;
  (b) line stop

COUPLINGS, HOSE, QUICK CONNECT, comprising ALL of the following;
  (a) male sections;
  (b) female sections;
  (c) lever ring

FITTINGS, COUPLING, HOSE, quick connect, being ANY of the 
following:
  (a) male sections; 
  (b) female sections;
  (c) lever rings;
  (d) male plugs;
  (e) female caps

OILWELL CONNECTORS, having ALL of the following:
  (a) nonhelical interlocking teeth;
  (b) metal to metal seals;
  (c) diameter NOT less than 50.8 cm

MODULAR PANEL BRIDGE, including ALL of the following:
  (a) panels;
  (b) chord reinforcements;
  (c) rakers;
  (d) transoms;
  (e) braces;
  (f) decks;
  (g) kerbs;
  (h) in-fills;
  (i) post ends;
  (j) base AND/OR batten plates;
  (k) frames;
  (l) beams,
with OR without ANY of the following:
          (i) channels;
         (ii) angles;
        (iii) stanchions;
         (iv) handrails

DOORS, sectional, including ALL of the following:
  (a) polyurethane foam insulating core;
  (b) galvanised steel sheet outer faces;
  (c) perimeter gaskets;
  (d) class 6 air permeability complying with European Standard 
      EN 13241-1:+A1 (EN 13241-1:+A1)

FIRE DOORS, hinged OR sliding, having ALL of the following:
  (a) complying with NORSOK standard C-002 AND International 
      Code for application of Fire Test Procedures 2010;
  (b) complying with fire ratings NR OR A0 OR A60 OR A90 OR A120
      OR H0 OR H60 OR H90 OR H120;
  (c)  manual OR pneumatic OR electrical operation

LANDING DOORS, LIFT AND/OR ELEVATOR

SLIDING DOOR SYSTEM, CAVITY, BRICK WALL, incorporating 
overlapping steel mesh

GRILLS, SECURITY, metal, retractable, self locking

DECKS, SCAFFOLDING, having ALL of the following:
  (a) punched anti-slip surface;
  (b) stiffening band;
  (c) zinc coated;
  (d) maximum load rating NOT less than 2 kPa and NOT greater
      than 38 kPa;
  (e) side hooks

PARTS, LATTICE PROPPING AND/OR SHORING SYSTEM, being ANY of the 
following:
  (a) adapter;
  (b) collar;
  (c) dome;
  (d) jack spindle AND collar assembly whether OR not 
      assembled;
  (e) leg;
  (f) load release unit;
  (g) plate;
  (h) pyramid extension;
  (i) pyramid head;
  (j) stool;
  (k) stub end

PARTS, SOFFIT FORMWORK AND/OR DECKING, being ANY of the 
following:
  (a) prop head adaptors;
  (b) dropheads;
  (c) clips;
  (d) tie down connectors;
  (e) prop locators;
  (f) props;
  (g) tripods;
  (h) guardrail AND/OR handrail sockets;
  (i) guardrail AND/OR handrail posts;
  (j) infill beams;
  (k) prop pins;
  (l) prop stepped pins;
  (m) brackets

PARTS, SHORING AND PROPPING SYSTEM, having a axial load capacity 
NOT less than 700 kN, being ANY of the following:
  (a) leg;
  (b) jack;
  (c) plate;
  (d) brace;
  (e) rocking head;
  (f) connector;
  (g) coupler;
  (h) adapter

STEEL COMPONENTS, being temporary shuttering AND part of a 
removable modular system, including prefabricated grids AND 
panels, being soffit bases

COMPONENTS, SCAFFOLDING, complying with Australian Standard AS 
1576.2, being ANY of the following:
  (a) double couplers;
  (b) double reducers;
  (c) swivel couplers;
  (d) swivel reducers;
  (e) putlog half;
  (f) putlog hooks;
  (g) putlog full;
  (h) putlog blades;
  (i) internal joiners;
  (j) gravlock beam clamps;
  (k) swivel beam clamps

SCAFFOLDING COMPONENTS, being ANY of the following:
  (a) V-housings;
  (b) camlocks;
  (c) ledgers;
  (d) toe board clamps

COMPONENTS, SCAFFOLDING, being ANY of the following:
  (a) chainwire rolls;
  (b) ledgers;
  (c) tie bars;
  (d) toe board clips;
  (e) wall ties;
  (f) wall tie tubes

PROPS, HOT DIPPED GALVANISED AND/OR ZINC PLATED, having a rolled 
thread on the outer tube

RAILS, elevator guide, weight less than 6 kg/m or exceeding
 26 kg/m

SHAPES AND PROFILES, of puddled wrought iron

PARTS, MUSHROOM SUBSTRATE PASTEURIZATION TUNNELS OR BUILDINGS, 
being ANY of the following:
  (a) connection plates;
  (b) beams;
  (c) pillars;
  (d) panels;
  (e) profile sheets;
  (f) walls;
  (g) roofing

PARTS, DEMOUNTABLE FLOOD CONTROL CONTAINMENT SYSTEM, conforming 
to British Standard PAS 1188-4, (BSI PAS 1188-4), being ANY of 
the following:
  (a) supports;
  (b) braces;
  (c) support covers

PARTS, FORMWORK, PANEL WALL SYSTEM, being ANY of the 
following:
  (a) adapters;
  (b) add-on pieces;
  (c) adjustment pieces;
  (d) bases;
  (e) braces;
  (f) brackets;
  (g) clamps;
  (h) cones;
  (i) connector assemblies, comprising both ends and clamps;
  (j) connectors;
  (k) hinged and/or fixed corners;
  (l) cross-bars;
  (m) ends;
  (n) fasteners;
  (o) form strips;
  (p) frames;
  (q) guardrails;
  (r) joints;
  (s) locating pins;
  (t) mid rails;
  (u) panels;
  (v) plates;
  (w) platforms;
  (x) plugs;
 (aa) posts;
 (ab) props;
 (ac) railing;
 (ad) spindles;
 (ae) spacer and/or centre tubes;
 (af) stiffeners;
 (ag) stop ends;
 (ah) struts;
 (ai) tie rods;
 (aj) tighteners;
 (ak) transport hooks;
 (al) triangular wedges;
 (am) waler spanners;
 (an) walers;
 (ao) wedges

PARTS, BOILER POWER PLANT, fabricated structural steel, being 
ANY of the following:
  (a) gratings;
  (b) handrails, assembled, with OR without kick plates, having  
      stanchions; 
  (c) bracings;
  (d) stair treads

PARTS, MODULAR MULTIDIRECTIONAL FRAMEWORK, conforming to 
European Standard 13480 (EN:13480) and European Standard 
1993 (EN:1993), being ANY of the following:
  (a) adapters;
  (b) bases;
  (c) ends;
  (d) joints;
  (e) plates;
  (f) spider clamps

SECTIONS, WIND GENERATOR TOWER, with OR without foundation ring, 
having ALL of the following:
  (a) top diameter NOT less than 29 000 mm and NOT greater than
      45 000 mm; 
  (b) bottom diameter NOT less than 32 000 mm and NOT greater
      than 45 000 mm; 
  (c) section length NOT less than 16 000 mm and NOT greater than
      32 000 mm;
  (d) section weight NOT less than 26 000 kg and NOT greater than
      55 000 kg

PARTS, TOWER CRANE, being EITHER of the following:
  (a) jib extensions;
  (b) jib sections,
with OR without ANY of the following:
          (i) guys;
         (ii) connectors;
        (iii) pull rods;
         (iv) tie bars

PARTS, GAS DISTRIBUTION SYSTEM, including ALL of the following:
  (a) elbows;
  (b) flanges;
  (c) straight OR reducing tees;
  (d) concentric OR eccentric reducers;
  (e) couplings;
  (f) nipples;
  (g) plugs;
  (h) caps;
  (i) seamless OR welded piping;
  (j) pipe supports;
  (k) lap joints;
  (l) bushings;
  (m) screws AND nuts AND bolts;
  (n) gaskets;
  (o) bellows;
  (p) spacers;
  (q) orifices;
  (r) studs

SUBSEA SUPPORT FOUNDATIONS, UMBILICAL TERMINATION ASSEMBLY

EXHAUST STACKS, GAS TURBINE, steel, with OR without ANY of the 
following:
  (a) exhaust duct;
  (b) silencer;
  (c) expansion joint

RACKING, STORAGE AND RETRIEVAL SYSTEM, including BOTH of the 
following:
  (a) shuttle module travel rails;
  (b) rear grating enclosure

WALL BUMPERS, stainless steel, having ALL of the following:
  (a) width NOT greater than 200 mm;
  (b) depth NOT greater than 32 mm;
  (c) closed end

PANELS, modular, interlocking, having BOTH of the following:
  (a) metal coating;
  (b) aluminium honeycomb core

PANELS, INSULATING, non-combustible, having BOTH of the 
following:
  (a) metal coating;
  (b) aluminium honeycomb OR mineral wool core

SUCTION PILES, with OR without lifting sling, being ALL of the 
following:
  (a) weight NOT less than 300 tonnes; 
  (b) height NOT less than 22.5 m;
  (c) diameter NOT less than 7.5 m

WALL AND ROOF PANELS, INSULATING, metal, having ALL of the 
following:
  (a) polyurethane foam backed;
  (b) tongue AND groove;
  (c) concealed fixing;
  (d) thickness NOT greater than 40 mm

PARTS, FORMWORK, being ANY of the following:
  (a) catwalks;
  (b) stairs AND ladders AND railings;
  (c) base frames AND platforms AND kick plates;
  (d) pillars AND railing

SOLDIERS, FORMWORK, having BOTH of the following:
  (a) length NOT greater than 3 650 mm;
  (b) width NOT greater than 220 mm

TILTING AND TRACKING SUPPORTS, SOLAR PANEL, with OR without 
braces, being ANY of the following:
  (a) torque tube splice brackets having NOT less than 4 holes;
  (b) post head Y OR C connectors OR U lower brackets, having 
EITHER or BOTH of the following:
         (i) round holes;
        (ii) keyholes,
  (c) tracker components having ANY of the following:
        (a) motor support brackets, having EITHER or BOTH of the
            following:
              (a) keyholes;
              (b) welded gussets,
        (b) panel rail clamps AND brackets;
        (c) fastener brackets, having NOT less than 2 holes;
        (d) driveline plates AND brackets;
        (e) inclinometer brackets;
        (f) torque tube spring brackets

STACK, WASTE GAS, including ALL of the following:
  (a) chimney height NOT less than 100 metres;
  (b) chimney external diameter NOT less than 3 metres;
  (c) inlet flange

ROADSIDE PROTECTION RAILS, MOTORCYCLE, complying with Australian 
Standard AS/NZS 3845.1:2015, having ALL of the following:
  (a) barrier profiles NOT greater than 6 m in length;
  (b) mounting OR support brackets;
  (c) barrier end fittings,
with OR without ANY of the following:
     (i) bolts;
    (ii) nuts;
   (iii) washers

PARTS, BUILDING SAFETY SCREEN, being ANY of the following:
  (a) flashings;
  (b) fixing strips;
  (c) covers;
  (d) brackets;
  (e) cladding angles;
  (f) spacers;
  (g) panels;
  (h) braces;
  (i) beams;
  (j) sliders;
  (k) mounts;
  (l) soldiers;
  (m) plates;
  (n) cones;
  (o) beam struts

STRUCTURES, ELEVATED CONCRETE MIXER PLATFORM, including ALL of 
the following:
  (a) NOT less than two platforms;
  (b) stairways AND/OR railings;
  (c) mixer platform width NOT less than 4 600 mm;
  (d) mixer platform length NOT less than 9 200 mm;
  (e) steel columns,
with OR without EITHER of the following:
           (i) base plates;
          (ii) cross bracing

PARTS, ECONOMISER SUPPORT STRUCTURE, being ALL of the following:
  (a) support beams;
  (b) hanger rods;
  (c) u-beam;
  (d) plates

BOOM SUPPORT POST, OIL AND/OR GAS BURNER, whether OR not 
assembled, including ALL of the following:
  (a) base plate;
  (b) pad eyes;
  (c) fishplate AND vertical column AND rear bracket having  
      maximum weight capacities exceeding 19 tonnes at a 27 
      degrees angle

ASSEMBLIES, BOILER ECONOMIZER SUPPORT STRUCTURE, having a 
maximum load carrying capacity NOT less than 250 t, including 
ALL of the following:
  (a) beams;
  (b) hanger rods;
  (c) u-shaped beams;
  (d) plates

SECTIONS, WIND GENERATOR TOWER, having ALL of the following:
  (a) plate steel having a thickness of NOT less than 30 mm and
      NOT greater than 60 mm; 
  (b) section length NOT less than 15 500 mm and NOT
      greater than 22 000 mm;
  (c) section weight NOT less than 80 metric tonnes 
      and NOT greater than 120 metric tonnes;
  (d) outer diameter NOT less than 4 400 mm and NOT greater  
      than 4 900 mm

TILTING AND TRACKING SUPPORTS, SOLAR PANEL, with OR without 
braces, including ALL of the following:
  (a) U shaped section panel rails, having BOTH of the following:
        (i) NOT less than 8 holes;
       (ii) length NOT greater than 6 metres,
  (b) steel ground posts, having BOTH of the following:
        (i) NOT less than 2 holes;
       (ii) length NOT greater than 6 metres,
  (c) torque tube splice brackets having NOT less than 8 holes,
  (d) torque tubes, having BOTH of the following:
        (i) rectangular openings;
       (ii) length NOT greater than 12 metres,
  (e) post head Y connectors, having BOTH the following:
        (i) round holes;
       (ii) keyholes,
  (f) conforming with ALL of the following:
        (i) Australian/New Zealand Standard AS/NZS1170.0:2002
            Part 0 General Principals;
       (ii) Australian/New Zealand Standard AS/NZS1170.2:2011
            Part 2 Wind Actions;
      (iii) Australian/New Zealand Standard AS/NZS1170.4:2007
            Part 4 Earthquake actions in Australia;
       (iv) Australian Standard AS4100:1998 Steel Structures;
        (v) Australian Standard AS4600:2005 Cold Formed Steel
            Structures,
with OR without ANY of the following: 
        (i) motor support brackets, having BOTH the following;
            (a) keyholes;
            (b) welded gussets,
       (ii) panel rail clamps;
      (iii) post head bushings;
       (iv) fastener brackets, having NOT less than 6 holes

SECTIONS, WIND GENERATOR TOWER, having ALL of the following:
  (a) plate steel having a thickness of NOT less than 33 mm and
      NOT greater than 60 mm; 
  (b) section length NOT less than 14 100 mm and NOT
      greater than 16 250 mm;
  (c) section weight NOT less than 60 metric tonnes 
      and NOT greater than 105 metric tonnes;
  (d) diameter NOT less than 4 299 mm and NOT greater than 
      4 650 mm

PEDESTALS, COOLING TUNNEL, unassembled, including ALL of the 
following:
  (a) stainless steel checkered plate covering;
  (b) stairs AND rails;
  (c) chemical dowel fixtures

CYCLONE STRUCTURES, IRON ORE PROCESSING PLANT, hot dipped 
galvanised steel, unassembled, including ALL of the following: 
  (a) walkways; 
  (b) guards;
  (c) sump frame;
  (d) cyclone frame

PARTS, GERMINATING AND/OR KILNING VESSEL, with OR without 
fasteners, being ANY of the following:
  (a) eave rings;
  (b) wall AND/OR roof segments;
  (c) roof beams AND roof centre rings;
  (d) consoles, consisting of ANY of the following:
        (i) brackets;
       (ii) shims;
      (iii) plates;
       (iv) plate tops;
        (v) reinforcing ribs AND profiles,
  (e) running rails;
  (f) bracing;
  (g) erection templates AND jigs

PARTS, FORMWORK AND/OR SAFETY SCREEN, VERTICAL CLIMBING SYSTEM, 
being ANY of the following:
  (a) beams;
  (b) braces;
  (c) brackets;
  (d) frames;
  (e) latches;
  (f) masts;
  (g) supports;
  (h) bracing tubes;
  (i) struts;
  (j) adapters;
  (k) connectors;
  (l) extensions

CLIPS, ROOF AND/OR WALL SHEETING

PUSH BACK PALLET RACKING SYSTEM, including BOTH of the following:
  (a) trolleys;
  (b) support beams

BEAMS, FLOORING SUPPORT, steel, assembled OR unassembled, having 
ALL of the following:
  (a) beam lengths NOT less than 8 200 mm;
  (b) complete penetration butt welded steel plate complying with
      Australian Standard AS 4100-1998, 9.7.2.7;
  (c) bevelled beam ends, with end plates attached,  
with OR without ANY of the following:
         (i) nuts;
        (ii) bolts;
       (iii) washers

ACCESS BOXES OR CUBES OR PRISMS, rectangle, steel, modular, 
including ANY of the following:
  (a) connector plates;
  (b) end panels;
  (c) brackets;
  (d) cross beams;
  (e) spreader;
  (f) steel plate supports

GUIDE RAILS, iron AND/OR steel, cold-drawn, having a rail length 
less than 5.5 m, with OR without fishplates

SHORING, steel, modular, hydraulic adjustable, including ALL of 
the following:
  (a) braces;
  (b) struts;
  (c) beams

STRUCTURES, STEEL, MARINE BERTHING, being ANY of the
following:
(a) marine piles NOT less than 750 mm diameter;  
(b) dolphins NOT less than 25 tonnes;
(c) topside modules NOT less than 75 tonnes

PARTS, STRUCTURAL STEEL, COAL PLANT OR IRON ORE PLANT, being 
ANY of the following:
  (a) rolled, hollow or welded sections;
  (b) beams;
  (c) grating,
  (d) stairways and/or treads;
  (e) plates;
  (f) handrails (with or without kick plates);
  (g) stanchions;
  (h) purlins and girts;
  (i) packing and shims;
  (j) guards;
  (k) legs;
  (l) stringer and ground modules;
  (m) frames;
  (n) wear liners;
  (o) gantries

SOLDIERS, FORMWORK, having ALL of the following:
  (a) length NOT greater than 3 650 mm;
  (b) width NOT less than 220 mm;
  (c) hole diameter NOT greater than 105 mm

STRUCTURES, STEEL, GAS FUELLED POWER PLANT, being EITHER of the 
following:
  (a) exhaust gas stack;
  (b) radiator platform

WATER DIVERSION OR DAM BARRIERS, mobile, including ALL Of the 
following:
  (a) steel A shaped frames;
  (b) steel connecting rods;
  (c) plywood AND/OR aluminium panels;
  (d) plastic membrane sheets;
  (e) steel clips AND chains;
  (f) storage crates AND wooden pallets

TUBES, GAS STACK, VENT OR FLARE

PARTS, ACCESS FLOORING, being ANY of the following:
  (a) steel encapsulated chipboard core panels AND/OR calcium
      sulphate core panels;
  (b) pedestals, including a head, base and gasket;
  (c) stringers, complete with gasket

PARTS, FOUNDATION, VERTICAL ROLLER MILL, CEMENT GRINDING, being 
ANY of the following: 
  (a) multi-drive foundation frames;
  (b) thrust bearing gearbox base plates;
  (c) gearbox plate recess boxes;
  (d) anchorage base plates;
  (e) mill foundation anchor plates;
  (f) mill foundation slide rails;
  (g) rocker arm support pedestals;
  (h) assembly and alignment equipment having ALL of the 
      following:
        (i) I-beams;
       (ii) threaded rod;
      (iii) compensation plates;
       (iv) plates,
  (i) anchor bolt recess boxes;
  (j) I-beams being foundation embedments

ROOFING, MODULAR, being ANY of the following:
  (a) roof cassettes;
  (b) ridge cassettes;
  (c) roof beams;
  (d) roof girders;
  (e) ridge supports;
  (f) beam stiffeners;
  (g) tubular stiffeners;
  (h) lattice beam connectors;
  (i) wedges;
  (j) clamping plates;
  (k) roof supports

PANELS, INSULATING, consisting of polyurethane inner core with 
galvanised steel sheeting BOTH sides, having BOTH of the 
following:
  (a) steel sheet thickness NOT less than 0.4 mm;
  (b) polyurethane thickness NOT less than 20 mm

PARTS, MUSHROOM SUBSTRATE PASTEURIZATION TUNNELS OR BUILDINGS, 
being ANY of the following:
  (a) connection plates;
  (b) beams;
  (c) pillars;
  (d) panels;
  (e) profile sheets;
  (f) walls;
  (g) roofing

PARTS, FORMWORK, SOLDIER SYSTEM, being ANY of the following:
  (a) adapters;
  (b) bases;
  (c) braces;
  (d) brackets;
  (e) clamps;
  (f) clips;
  (g) connectors;
  (h) couplers;
  (i) edge angles;
  (j) fork arms;
  (k) fork heads;
  (l) guardrails;
  (m) jacks;
  (n) lifting loops and/or plates and/or brackets;
  (o) pivots;
  (p) plates;
  (q) plumbing braces;
  (r) posts;
  (s) shoring adapters;
  (t) soldiers, having holes NOT greater than 70 mm 
      diameters;
  (u) spreader connections and/or beams and/or adaptors;
  (v) stabilisers;
  (w) turnbuckles;
  (x) u-heads;
  (y) brackets (high load washer);
  (z) web stiffeners;
 (aa) wheel and bracket assemblies, comprising both wheels and 
      brackets

PARTS, FORMWORK, PANEL WALL SYSTEM, being ANY of the 
following:
  (a) adapters;
  (b) add-on pieces;
  (c) adjustment pieces;
  (d) angles;
  (e) bases;
  (f) braces;
  (g) brackets;
  (h) clamps;
  (i) cones;
  (j) connector assemblies, comprising both ends and clamps;
  (k) connectors;
  (l) hinged and/or fixed corners;
  (m) cross-bars;
  (n) ends;
  (o) fasteners;
  (p) form strips;
  (q) frames;
  (r) guardrails;
  (s) joints;
  (t) locating pins;
  (u) mid rails;
  (v) panels;
  (w) plates;
  (x) platform beams;
  (y) platforms;
  (z) plugs;
 (aa) posts;
 (ab) props;
 (ac) railing;
 (ad) spindles;
 (ae) spacer and/or centre tubes;
 (af) stiffeners;
 (ag) stop ends;
 (ah) struts;
 (ai) tie rods;
 (aj) tighteners;
 (ak) transport hooks;
 (al) triangular wedges;
 (am) waler spanners;
 (an) walers;
 (ao) wedges

STRUCTURES, FACADE, woven mesh, stainless steel

ACCESS FLOORING, comprising ALL of the following:
   (a) steel cementitious floor panels;
   (b) pedestals;
   (c) stringers;
   (d) pedestal heads

PARTS, ACCESS FLOORING, being ANY of the following:
   (a) steel cementitious floor panels;
   (b) pedestals;
   (c) stringers;
   (d) pedestal heads

GUIDE RAILS, LIFT, hot rolled, bright drawn and planed

CHILD SAFETY GATES OR EXTENSIONS, DOMESTIC, internal

CHAIN LOCKERS, weight NOT less than 80 metric tonnes, with OR 
without platform

TOTE BINS, stainless steel, having ALL of the following
  (a) capacity NOT greater than 805 litres;
  (b) operating pressure NOT greater than 1 bar;
  (c) manhole lid;
  (d) valves

STORAGE CONTAINERS; having all of the following:
  (a) volume NOT less than 600 L and NOT greater than 800 L;
  (b) lid position lockable at 70 deg and 270 deg;
  (c) stackable;
  (d) forklift lifting channels;
  (e) crane lifting points;
  (f) pressure relief valve;
  (g) galvanized steel construction,
 with OR without the following:
      (i) internal container AND protective earth inlet; 
     (ii) enameled lid

TANKS, GERMINATION AND/OR KILNING, BARLEY MALT, steel, 
prefabricated, having ALL of the following:
  (a) batch load capacity NOT less than 360 tonnes;
  (b) diameter NOT less than 27 m;
  (c) mild steel outer casing AND stainless steel inner casing;
  (d) manufacturing tolerance of 0 to +10 mm

DOSING BINS, FEED MILL, whether OR not assembled, having BOTH of 
the following:
  (a) bins having a volume NOT less than 900 litres and
      NOT greater than 2 000 litres;
  (b) bin top coverings having ALL of the following:
          (i) steel plate having a thickness NOT less 
              than 5 mm and NOT greater than 7 mm; 
         (ii) allowable traffic load NOT less than
              280 kilograms per square metre;
        (iii) access hatches AND/OR manholes

RETENTION BUNDS, modular, with OR without ANY of the following:
  (a) extinguishing system;
  (b) splash trays

CRUCIBLES, MOLTEN METAL PROCESSING, including ALL of the 
following:
  (a) stand;
  (b) inside diameter NOT less than 1 730 mm;
  (c) outside diameter NOT less than 1 909 mm;
  (d) internal volume NOT greater than 3.1 cubic
      metres

CRUCIBLES, MOLTEN METAL PROCESSING, with OR without stand, 
including ALL of the following:
(a) crucible inside diameter NOT less than 1 730 mm;
(b) crucible outside diameter NOT less than 1 909 mm;
(c) crucible internal volume NOT greater than 3.1 cubic metres

BIN BLOCKS, FACE MIX AGGREGATE, hot galvanised, having ALL of 
the following:
  (a) bin cones having bolted 6 mm trapezoidal bent sides;
  (b) outlet flanges; 
  (c) braced steel bin supports;
  (d) flat iron gratings;
  (e) horizontal gangways AND railings

COARSE-MIX AGGREGATE BINS, SILO BLOCK, multi cell, having ALL of 
the following:
  (a) steel hoppers;
  (b) steel checker plate mesh decking;
  (c) horizontal AND longitudinal braced steel supporting 
      structure;
  (d) stairways AND walkways AND safety railings;
  (e) level AND temperature control connections

TANKS, FUEL STORAGE, double walled, transportable with OR 
without fuel, having ALL of the following:
  (a) galvanized steel frame;
  (b) removable inner tank;
  (c) internal baffles;
  (d) forklift pockets;
  (e) access manway;
  (f) corner lifting brackets;
  (g) storage capacity NOT less 480 litre

INTERMEDIATE BULK CONTAINER, POWDER HANDLING AND BLENDING, 
having ALL of the following:
  (a) capacity NOT greater than 2000 L and not less than 1000 L;
  (b) stainless steel;
  (c) internal finish certified to Ra 15 microinch;
  (d) butterfly valve operated discharge port

MATERIAL HANDLING AND STORAGE SYSTEM, AQUACULTURE FEED MILL, 
including ALL 
of the following:
  (a) silos, including BOTH of the following:
          (i) hoppers;
         (ii) chutes,
  (b) elevator, including BOTH of the following:
          (i) feeders;
         (ii) drive motor,
  (c) bag filling system, including ALL of the following:
          (i) hopper;
         (ii) filter;
        (iii) fan,
  (d) screw conveyor

WATER TANKS, AQUACULTURE FEED MILL, including ALL of 
the following: 
  (a) ventilation cap;
  (b) foam free inlet;
  (c) overflow pipe;
  (d) inspection man cover;
  (e) sensor socket AND transmitter

TANKS, STORAGE, having ALL of the following:
  (a) maximum volume capacity NOT less than 2.5 m3;
  (b) outlet nozzles;
  (c) stainless steel shell, 
with OR without manhole covers

TANKS, STORAGE, having ALL of the following:
  (a) maximum volume capacity NOT less than 15 m3;
  (b) outlet nozzles;
  (c) manhole cover;
  (d) stainless steel shell

TANKS, hermetically sealable, having ALL of the following:
  (a) radiator fins having a height NOT less than 50 mm and 
      NOT greater than 400 mm;
  (b) radiator fin fold having a length NOT less than 400 mm and
      NOT greater than 1 600 mm;
  (c) single corrugated tank wall having a thickness NOT less
      than 5 mm;
  (d) lockable ball valve having a valve diameter NOT less 
      than 32 mm

TANKS, BEVERAGE, including BOTH of the following:
  (a) storage capacity NOT greater than 1 000 L and NOT less
      than 500 L;
  (b) operating tap pressure NOT greater than 3 bar,
with OR without ANY of the following: 
        (i) manhole, having a cover;
       (ii) piercing unit, having a tap;
      (iii) safety valves;
       (iv) support frames;
        (v) beverage distributor AND/OR divider heads

TANKS, ASEPTIC, VACUUM, including ALL of the following:
  (a) maximum internal pressure NOT less than 5 bars;
  (b) volume capacity NOT less than 2 000 L;
  (c) operating nitrogen pressure NOT less than 0.2 bars and NOT
      greater than 0.4 bars;
  (d) elliptically shaped upper tank head AND conically shaped
      lower tank bottom;
  (e) air AND nitrogen connection ports;
  (f) aseptic pneumatic valves;
  (g) feeder pipe sight glass;
  (h) inspection manhole

TANKS, CHEMICAL, having ALL of the following:
  (a) capacity NOT less than 1 000 litres and NOT greater than 
      2 000 litres;
  (b) connection flanges in BOTH of the following sizes;
        (i) DN25;
       (ii) DN80,
  (c) tri-clamp in BOTH of the following sizes;
        (i) DN40;
       (ii) DN70,
  (d) manhole cover with safety switch;
  (e) piping;
  (f) AISI 304 stainless steel grade tank

AUTOCLAVE VESSELS, ACID LEACH, having ALL of the following:
  (a) slurry operating volume NOT less than 647 cubic metres;
  (b) internal diameter NOT less than 5.0 m;
  (c) length NOT less than 32 m;
  (d) six agitation compartments;
  (e) explosively bonded titanium lining on carbon steel shell;
  (f) free acid in slurry after metal leaching greater than 50 
      grams/litre;
  (g) slurry temperature NOT greater than 255 degrees Celsius;
  (h) vessel operating pressure NOT greater than 5 500 kPag

PRESSURE VESSELS, self-regulating, having ALL of the following:
  (a) capacity NOT less than 10 000 litres;
  (b) butyl rubber bladder complying with Australian
      Standard AS 4020:2005;
  (c) with OR without gas valve unit for nitrogen charging

SILOS, PRE-CAST CONCRETE PLANT, telescopic, bolted modules, 
steel, programmable logic controlled, including ALL of the 
following:
  (a) capacity NOT less than 65 000 litres;
  (b) aeration system, having a solenoid valve;
  (c) roof mounted pressure safety valves;
  (d) shut down valves;
  (e) level indication;
  (f) anti overfill protectors, having alarms AND/OR lights;
  (g) filters AND/OR dust collectors, roof mounted

TANKS, STORAGE, stainless steel, unassembled, having BOTH of the 
following:
  (a) panel lengths NOT less than 2 m;
  (b) NOT less than 8 panels for each tank,
with OR without ANY of the following:
        (i) tank covers;
       (ii) internal guide rails;
      (iii) steel reinforced floor panels;
       (vi) mounting plates AND support poles;
        (v) steel panels with manholes AND manhole covers;
       (vi) valves;
      (vii) steel OR polyvinyl chloride(PVC) pipes

SILOS, bolted modules, steel, whether OR 
not assembled, with OR without stairs, having ALL of the 
following:
  (a) piping AND/OR hoses with OR without connectors;
  (b) flow control valves;
  (c) level measurement microwave sensor including display;
  (d) capacity NOT less than 155 cubic metres and NOT greater 
      than 4 500 cubic metres

TANKS, HOT WATER, having ALL of the following:
  (a) welded steel plate construction;
  (b) insulation AND cladding thickness NOT less than 200 mm; 
  (c) temperature capacity NOT less than 5 degrees Celsius and
      NOT greater than 95 degrees Celsius;   
  (d) pressure capacity NOT less than 56 mbar;
  (e) water capacity NOT less than 100 000 L

TANKS, WASTE WATER, glass lined steel, having BOTH of the 
following:
  (a) diameter NOT less than 4 200 mm;
  (b) height NOT less than 5 600 mm

COLD FEED MODULE, ASPHALT PLANT

RECLAIMED ASPHALT PAVEMENT (RAP) MODULE, ASPHALT PLANT

DUST AND FILLER SILO MODULE, ASPHALT PLANT

SURGE TANKS, VERTICAL, OIL AND GAS WELL TESTING

TANKS, COLD WATER, DIAPHRAGM PRESSURE, having a capacity 
exceeding 300 L and NOT greater than 500 L

TANKS, BEVERAGE, including BOTH of the following:
  (a) storage capacity NOT greater than 250 L;
  (b) operating tap pressure NOT greater than 3 bar,
with OR without ANY of the following: 
        (i) manhole, having a cover;
       (ii) piercing unit, having a tap;
      (iii) safety valves;
       (iv) support frames;
        (v) beverage distributor AND/OR divider heads

TANKS, COLD WATER, DIAPHRAGM PRESSURE, having a capacity NOT 
less than 50 L and NOT greater than 300 L

KEGS, BEVERAGE, stainless steel, with OR without spears

CONTAINERS, cryogenic, insulated or vacuum wall, using liquefied
 gas as a refrigerant medium to store goods (OTHER THAN gas),
 at a temperature below - 100 degrees C

KEGS, BEVERAGE, stainless steel, having a volume capacity less 
than 50 L, with OR without keg spears

TINS, PACKAGING, tin coated, with 
or without hinged lid

TANKS, COLD WATER, diaphragm pressure, having a volume capacity 
NOT greater than 50 L

TANKS, COLD WATER, diaphragm pressure, having a capacity less   
than 50 litres

JERRY CANS, conforming to Australian/New Zealand Standard 
2906:2001 (AS/NZS 2906:2001)

TINS, NOVELTY, having less than 220 grams of confectionery 
and/or bakers wares

CYLINDERS, seamless, forged accumulator shell type, design
 approved to AS1210-1H, having BOTH of the following:
   (a) water capacity of 0.16 L or greater but NOT exceeding
       54 L;
   (b) pressure ratings of 20.7 MPa to 31.0 MPa or 34.5 MPa
       to 39.0 MPa

CYLINDERS, carbon dioxide gas, with self-contained valve
 capacity NOT exceeding 0.75 L

CYLINDERS, ACETYLENE, welded steel, containing porous mass filler

CYLINDERS, CRYOGENIC, stainless steel, having ALL of the following:
   (a) valve setting NOT greater than 1 650 kPa,
   (b) service pressure NOT greater than 1 380 kPa;
   (c) liquified gas capacity NOT greater than 400 L

CYLINDERS, GAS, seamless steel, having BOTH of the following:
   (a) maximum water capacity of NOT less than 49 L;
   (b) test pressure of NOT less than 7 MPa

CYLINDERS, GAS SAMPLING, seamless, stainless steel, double ended,
 having a test pressure of NOT less than 7 MPa

CYLINDERS, GAS, seamless steel, volume NOT less than 30 litre water
 capacity, having a test pressure NOT less than 45.0 MPa

PRESSURISED CYLINDERS, GAS, seamless steel, having ALL of the 
following:
  (a) working pressure NOT greater than 300 bar;
  (b) diameter NOT greater than 229 mm;
  (c) length NOT greater than 1 490 mm;
  (d) empty weight NOT greater than 62 kg;
  (e) water capacity NOT greater than 50 litres;
  (f) concave base

CYLINDERS, GAS, having ALL of the following: 
  (a) external wrapping of carbon fibre construction; 
  (b) stainless steel liner; 
  (c) test pressure exceeding 400 Bar; 
  (d) complying with North Atlantic Treaty Organisation 
      Standard AEODP-07, Contact NM-A (NATO standard AEOPD-07)

TANKS, RECEIVER, welded, having BOTH of the following:
  (a) maximum pressure capacity NOT greater than 19 barg;
  (b) liquid volume capacity NOT less than 145 cubic metres

CYLINDERS, HYDRAULIC PRESSURE, seamless, forged accumulator 
shell, having BOTH of the following:
  (a) liquid volume capacity NOT less than 0.16 L and NOT greater
      than 54 L;
  (b) liquid pressure maximum capacity NOT less than 20 MPa

TANKS, CRYOGENIC, LIQUEFIED NATURAL GAS, stainless steel

TANKS, CRYOGENIC, liquefied gas, water capacity NOT less than  
400 litres

CYLINDERS, GAS, seamless steel, having a test pressure NOT less 
than 250 bar

CYLINDERS, GAS, seamless steel, having BOTH of the following:
   (a) water capacity NOT exceeding 50 litres;
   (b) rated to 300 bar

DEWARS, PRESSURISED OR LIQUEFIED GAS

ROPE, steel wire, locked coil, anti-twist having NOT less than
 21 outer wires

WIRE, stainless steel, seven strand, polyamide covered

CABLE OR ROPE, stainless steel

ROPE, STEEL WIRE, conforming to the rubber penetration test
 specified in AS 1333, 1994 Appendix L, with a change in pressure
 differential of 0.05 bar max after 60 seconds, being ANY of
 the following:
   (a) diameter 2 mm to 3 mm (both inclusive) 6 x 6 construction;
   (b) diameter 3 mm to 6 mm (both inclusive) 7 x 7 construction;
   (c) diameter 6 mm to 15 mm (both inclusive) 7 x 19 construction

ROPE, galvanised lubricated steel wire to Grade 1770, having ALL of
 the following:
    (a) diameter NOT less than 6.5mm and NOT greater than 16mm;
    (b) breaking load NOT less than 20.6 kn and not greater than
        139.3kn;
    (c) 2 or more strands of electrical conductors

ROPES, tow, steel, complete with hooking attachment

ROPE, wire galvanised, comprising ALL of the following:
   (a) diameter NOT less than 50 mm and NOT greater than 60 mm;
   (b) weight NOT greater than 14.4 kg/m;
   (c) minimum break load NOT less than 2 735 kN

WIRE ROPE, MOORING, sheathed, with OR without ANY of the 
following: 
  (a) connectors;
  (b) sockets; 
  (c) bend stiffeners;
  (d) lubrication compound

MOORING ROPE, galvanised wire with plastic jacket, steel reel 
AND cradle

CABLE, polyurethane coated, having screw lock connector OR 
permanent lock connector

WIRE STRANDS,  steel, pre-stressed, being ANY of the following 
sizes:
  (a) NOT greater than 15.2 mm, having a tensile strength of 
      1 830 Mpa;
  (b) NOT greater than 12.7 mm, having a tensile strength of 
      1 870 Mpa;
  (c) NOT greater than 9.50 mm, having a tensile strength of 
      1 850 Mpa
For the purposes of this Order, a tolerance of - 10% OR + 10% is 
allowable on all dimensions

WIRE STRANDS, steel, stress-relieved, in coils, having BOTH of 
the following:
  (a) NOT less than 7 wires;
  (b) modulus of elasticity NOT less 185 GPa

CABLES, GUY WIRE, coated with OR without a galvanised coating, 
including ALL of the following:
  (a) spiral strands;
  (b) open OR closed end sockets;
  (c) locking pins;
  (d) external diameter NOT less than 39 mm;
  (e) length NOT less than 75 m

CABLE, being 8x26 AND 8x31 strand, independent wire rope OR 
polymer core, parallel closed wire, having BOTH of the following:
  (a) diameter NOT less than 26 mm and NOT greater than 35 mm;
  (b) breaking force NOT less than 61 tonne

WIRE ROPE AND/OR CABLE, steel core, galvanised, tensile grade 
1770 N/mm2, in ANY of the following configurations:
  (a) 7/7 wire strand core in the following sizes:
            (i) 1.2 mm;
           (ii) 1.5 mm;
          (iii) 2 mm;
           (iv) 2.4 mm;
            (v) 3 mm; 
           (vi) 4 mm;
          (vii) 4.6 mm; 
         (viii) 4.75 mm; 
           (ix) 5 mm; 
            (x) 6 mm
  (b) 7/19 wire strand core in the following sizes:
          (i) 2 mm;
         (ii) 3 mm;
        (iii) 4.6 mm;
         (iv) 4.75 mm;
          (v) 6 mm;
         (vi) 8 mm,
  (c) 1/19 having a size NOT less than 1 mm and NOT 
      greater than 2 mm

WIRE ROPE, CAPSTAN WINCH, having BOTH of the following:
  (a) diameter 11 mm;
  (b) breaking load NOT less than 115 kN
For the purpose of this order tolerance for (a) is + or - 5%

WIRE ROPE, being ANY of the following:
  (a) grade 1570, construction 6 x 24, diameter NOT less than 
      12 mm and NOT greater than 15mm;
  (b) grade 1570, construction 7 x 7, diameter NOT less than
      6mm and NOT greater than 8 mm;
  (c) grade 1770, construction 6 x 19, diameter NOT less than
      9 mm and NOT greater than 11 mm;
  (d) grade 1770, construction 6 x 36, diameter NOT less than
      10 mm and NOT greater than 17 mm;
  (e) grade 2160, construction 6 x 25, diameter NOT less than
      10 mm and NOT greater than 17 mm;
  (f) grade 2160, construction 7 x 7, diameter NOT less than 
      6 mm and NOT greater than 8 mm;
  (g) grade 2160, construction 18 x 7, diameter NOT less than
      5 mm and NOT greater than 18 mm;
  (h) grade 2160, construction 19 x 7, diameter NOT less than
      6 mm and NOT greater than 18mm;
For the purpose of this Order, tolerances allowable on rope 
diameters are + OR - 5%

ROPE, galvanised steel wire, having BOTH of the following:
  (a) rope diameter NOT less than 95 mm;
  (b) breaking load NOT less than 703 t

WIRE ROPE, OIL AND GAS WELL, galvanised steel, with steel reel 
AND cradle

ROPE, WIRE, GALVANISED, having a diameter NOT less than 150 mm

CABLES, CONVEYOR BELT, steel, galvanised OR brass plated, having 
an outside cable diameter NOT less 3 mm and NOT greater than
15 mm

BELTING, ELEVATOR AND/OR LIFT, SUSPENSION AND/OR TRACTION, 
having a composition of BOTH of the following:
  (a) steel cords;
  (b) elastomeric coating AND fabric

ROPE, WIRE, galvanised steel OR stainless steel, having BOTH of 
the following:
  (a) rope diameter NOT less than 16 mm and NOT greater
      than 24 mm;
  (b) not LESS than 6 strands in each wire rope, having
      individual strands coated with polyamide OR polypropylene
      OR polyester

ROPE, WIRE, galvanised steel OR stainless steel, having ALL of 
the following:
  (a) rope diameter NOT less than 16 mm and NOT greater than
      18 mm;
  (b) 6 strand laid rope, individual strands coated with
      polyamide AND/OR polyester;
  (c) standard wire tenacity NOT less than 1770 N/mm2

ROPES, ELEVATOR, ungalvanized, having ALL of the following:
  (a) wire tensile strength NOT less than 1 365 N/mm2 and NOT 
      greater than 1 775 N/mm2;
  (b) rope diameter NOT less than 6 mm and NOT greater
      than 25 mm;
  (c) breaking load NOT less than 21.7 kN and NOT
      greater than 251 kN

ROPE, WIRE, being ANY of the following:
  (a) grade 1570, configuration 6/7, diameter NOT less than 
      2 mm and NOT greater than 6 mm;
  (b) grade 1570, configuration 6/19, diameter NOT less than 
      3 mm and NOT greater than 10 mm;
  (c) grade 1570, configuration 6/24, diameter NOT less than 
      8 mm and NOT greater than 11 mm;
  (d) grade 1570, configuration 7/7, diameter NOT less than
      1.6 mm and NOT greater than 5 mm;
  (e) grade 1770, configuration 6/25, diameter NOT less than
      8 mm and NOT greater than 19 mm;
  (f) grade 2070, configuration 7/7, diameter NOT greater than
      5 mm;
  (g) grade 2070, configuration 7/19, diameter NOT less than
      3 mm and NOT greater than 12 mm

ROPES, HAUL, CHAIRLIFT, stranded wire

STEEL STRANDS, 19 wire, to JIS G3536

ROPE, wire galvanised, comprising ALL of the following:
   (a) diameter NOT less than 50 mm and NOT greater than 60 mm;
   (b) weight NOT greater than 14.4 kg/m;
   (c) minimum break load NOT less than 2 735 kN

HOOPS, PRE-CAST CONCRETE, galvanised, having ALL of the 
following:
  (a) tensile strength per wire NOT less than 1 770 N/mm2;
  (b) safe work load NOT less than 4 tonnes;
  (c) steel OR aluminium ferrule

BELTS, conveyor filter screen, endless, stainless steel wire
 braided between stainless steel cables, having ALL of the following:
   (a) constructed from grade 316 stainless steel wire;
   (b) width NOT less than 400 mm

WOVEN WIRE, having 50 or more holes/cm measured along the warp
 and having 50 or more holes/cm measured along the weft

WIRE MESH BELTS, SPIRAL CONVEYOR, having a width NOT less than 
5 250 mm

CLOTH, stainless steel, woven, wire diameter NOT greater than
8 mm

WIRE MESH, STAINLESS STEEL, WOVEN, having BOTH of the following:
  (a) compliance with Australian Standard AS 5039-2003;
  (b) wire diameter NOT greater than 9 mm

WIRE MESH, woven, stainless steel, powder coated

WIRE MESH, STAINLESS STEEL, WOVEN, complying with BOTH of the
 following:
   (a) stainless steel alloy grade 304 OR 316 OR 317LM OR 890L OR
       904;
   (b) wire diameter NOT exceeding 0.2 mm

CHAIN, transmission, precision roller, single strand, conforming to
 Australian Standard AS 1532-1974 incorporating BS 228 and B 29.1
 having a pitch of 25.4 mm to 63.5 mm both inclusive, without
 attachments

CHAINS, roller, multiple strand, conforming to AS 1532:1982,
 incorporating BS 228:1984 and ANSI B 29-1:1975, having a pitch
 of 25.4 mm or greater but NOT exceeding 63.5 mm

CHAINS, bicycle, but NOT including motorcycle chains

CHAINS, ROLLER BUSH, having ALL of the following:
   (a) pitch within EITHER of the following ranges:
          (i) 4 mm to 8 mm, inclusive;
         (ii) 12.7 mm to 76.2 mm, inclusive;
   (b) any of the following configurations:
          (i) simplex;
         (ii) duplex;
        (iii) multistrand;
   (c) conforming to ANY of the following standards:
          (i) ISO 606;
         (ii) DIN 8187;
        (iii) ANSI B29.1;
         (iv) BS 228

MOTORCYCLE CHAINS, sprocket, roller

CHAINS, TRANSMISSION, being roller OR bush OR inverted tooth chain,
 single or multi-strand, but NOT including single OR multi-strand
 chain having a pitch size of 9.525 mm

CHAINS, DRIVE, MOTORCYCLE

CHAIN, duplex stud bushed, rotary blast hole drill feed

CHAINS, roller, double pitch, having ALL of the following:
   (a) pitch:  50.80 mm;
   (b) inside link plate width:  15.88 mm;
   (c) roller diameter:  15.88mm or 28.58 mm;
   (d) pin diameter:  7.94 mm;
   (e) side plate thickness:  3.2 mm or 4.0 mm

CHAINS, roller, double pitch, having ALL of the following:
   (a) pitch:  25.40 mm;
   (b) inside link plate width:  7.95 mm;
   (c) roller diameter:  7.94 mm or 15.88 mm;
   (d) pin diameter:  3.97 mm;
   (e) side plate thickness:  1.5 mm

CHAINS, roller, double pitch, having ALL of the following:
   (a) pitch:  31.75 mm;
   (b) inside link plate width:  9.53 mm;
   (c) roller diameter:  10.16 mm or 19.05 mm;
   (d) pin diameter:  5.09 mm;
   (e) side plate thickness:  2.0 mm

CHAINS, roller, double pitch, having ALL of the following:
   (a) pitch:  38.10 mm;
   (b) inside link plate width:  12.70 mm;
   (c) roller diameter:  11.91 or 22.23 mm;
   (d) pin diameter:  5.96 mm;
   (e) side plate thickness:  2.4 mm or 3.2 mm

CHAINS, roller, tractor scraper elevator

CHAIN, power transmission, roller, heavy duty offset sidebar,
 complying with ALL of the following:
   (a) pitch 78.11 mm;
   (b) tensile strength 39 700 kg;
   (c) roller diameter 31.75 mm;
   (d) side plate thickness 9.5 mm;
   (e) side plate height 41.5 mm;
   (f) conforming to API Specification 7F

CHAINS, TRAVELLING GRATE

ROLLER CHAINS, GO-KART

CHAIN, conveyor, inverted tooth type, having a pitch of 12.7 mm
 to 25.4 mm (inclusive)

CONVEYOR CHAIN, slat top, straight running or side flexing, of
 hinged construction and having a pitch of 38.10 mm

CHAINS, leaf or balance

CHAINS, sprocket OR conveyor, and parts therefor, being roller
 bush OR inverted tooth type chain, but NOT including ANY of the
 following:
   (a) chain of a kind used in vehicles of a kind classified
       under subheadings 8701.30, 8703.21, 8703.22, 8703.23,
       8703.24, 8703.31, 8703.32, 8703.33, 8703.90, 8705.20,
       8705.30, 8705.40 or 8705.90;
   (b) conveyor OR elevator chain having a pitch size NOT
       exceeding 1 000 mm;
   (c) simple, duplex or triplex transmission chain of the roller
       OR bush types, having pitch sizes 9 mm to 10 mm (both
       inclusive) OR 26 mm to 153 mm (both inclusive)

MOTORCYCLE CHAINS, sprocket

CHAINS, swivel, cast block link, pitch 63.5 mm, pin diameter
 11.12 mm, overall width 41.27 mm and gear width 13.1 mm

CHAINS, combination, incorporating cast block links, in the
 following sizes:
   Pitch     Sidebar    Barrel      Gear
             height     diameter    width
   mm        mm         mm          mm
   101.60    38.10      30.17       50.80
   152.40    38.10      32.53       49.22
   120.90    44.45      36.52       60.32
    78.11    38.10      31.75       28.57
   153.67    50.80      45.23       79.37
    66.27    28.57      22.22       23.82

CONVEYING CHAINS, POULTRY FEEDING MACHINE, having 
interconnecting chain links

CHAINS, sprocket OR conveyor, and parts therefor, being roller
 bush OR inverted tooth type chain, but NOT including ANY of the
 following:
   (a) chain of a kind used in vehicles of a kind classified
       under subheadings 8701.30, 8703.21, 8703.22, 8703.23,
       8703.24, 8703.31, 8703.32, 8703.33, 8703.90, 8705.20,
       8705.30, 8705.40 or 8705.90;
   (b) conveyor OR elevator chain having a pitch size NOT
       exceeding 1 000 mm;
   (c) simple, duplex or triplex transmission chain of the roller
       OR bush types, having pitch sizes 9 mm to 10 mm (both
       inclusive) OR 26 mm to 153 mm (both inclusive)

PARTS FOR SIMPLE, DUPLEX OR TRIPLEX TRANSMISSION CHAIN, pitch size
 of 9.525 mm

PARTS, ROLLER BUSH CHAIN, being ANY of the following:
   (a) inner links;
   (b) outer links;
   (c) side plates;
   (d) fasteners

PARTS, TRAVELLING GRATE, being chain link assemblies

CHAINS AND COUPLINGS, bucket elevator (but NOT including steel
 roller or bush type chain), dia 26 mm or greater, proof tested
 special grade round steel stabilized with aluminium on Cr Ni
 base, with a minimum effective hardening depth of 0.04 mm depth
 minimum and stress at test load and breaking load NOT less than
 210 N/mm2 and 350 N/mm2 respectively

CHAIN, welded alloy steel, Grade T, having BOTH of the following:
   (a) conforming to AS 2321-1977;
   (b) link thickness exceeding 30 mm

CHAIN, LONGWALL MINING, having ALL of the following:
   (a) compliance with the minimum standards of DIN 22252;
   (b) compliance with standard DIN 17115 and a minimum
       high steel grade quality of 23MnNiCrMo52
       (material number 1.6541);
   (c) link diameter of 18 mm or greater;
   (d) pitch of 64 mm or greater

CHAINS AND COUPLINGS, welded link, bucket elevator or conveyor type,
 proof tested, alloy grade round steel stabilised with aluminium on
 Cr Ni base, stress at test load and breaking load NOT less than
 210 N/mm2 and 350 N/mm2 respectively, in ANY of the following sizes
 as set out in THE TABLE below:
          THE TABLE
   ROD DIAMETER        PITCH
   (a) 14 mm      x    50 mm;
   (b) 16 mm      x    64 mm;
   (c) 19 mm      x    75 mm;
   (d) 22 mm      x    86 mm

CHAIN, friction welded, CrNiMo alloy steel

MOORING CHAIN, welded, with OR without EITHER of the following: 
  (a) connectors;
  (b) coating

CHAINS, MANUAL AND/OR MOTOR DRIVEN HOIST, link diameter NOT less 
than 3 mm and NOT greater than 32 mm

CHAINS, LIFTING AND/OR LASHING, alloy steel, being grade 100 OR 
120

COUPLING CHAINS, welded steel, symmetrical, self-cleaning, 
having ALL of the following:
  (a) pitch length 73 mm OR 80 mm OR 90 mm OR 100 mm;
  (b) breaking loads NOT greater than 25 000 kg

CHAINS, LIFTING AND/OR LASHING, quenched AND tempered round 
steel link, having ALL of the following:
  (a) heat indicating powder coated finish;
  (b) impact toughness 55J at -60 degrees Celsius;
  (c) working temperature NOT less than -60 degrees Celsius and
      NOT greater than 300 degrees Celsius;

CHAINS, LIFTING AND/OR LASHING, quenched AND tempered round 
steel link, having ALL of the following:
  (a) heat indicating powder coated finish;
  (b) impact toughness 42J at -40 degrees Celsius;
  (c) working temperature NOT less than -40 degrees Celsius and
      NOT greater than 380 degrees Celsius

CHAINS, ELEVATOR OR CONVEYOR, welded link, alloy grade round 
steel, having ALL of the following:
  (a) calibrated pitch;
  (b) quenched AND tempered AND/OR case hardened;
  (c) surface hardness NOT less than 800 HV;
  (d) tensile stress at breaking load NOT less than 340 Newtons
      per square millimetre;
  (e) chain diameter NOT less than 7.9 mm and NOT greater than 
      38.1 mm;
  (f) pitch length NOT greater than 144 mm,
with OR without matched connectors

CHAINS, ELEVATOR OR CONVEYOR, welded link, alloy grade round 
steel, having ALL of the following:
  (a) calibrated pitch;
  (b) quenced AND tempered AND/OR case hardened;
  (c) surface hardness NOT less than 800 HV;
  (d) tensile stress at breaking load NOT less than 340 N/mm2;
  (e) chain diameter NOT less than 26 mm and NOT greater than 38
      mm inclusive;
  (f) pitch length NOT greater than 144 mm,
with OR without ANY of the following:
          (i) matched connectors;
         (ii) teeth;
        (iii) reversing wheel;
         (iv) sprocket wheels;
          (v) T-attachments;
         (vi) duo-mount

CARGO LIFTING SYSTEM, having ALL of the following:
  (a) woven polyester slings and strops;
  (b) metal extension lifting chains;
  (c) adjustable spreader bars

CHAIN, stainless steel, complying with American Society for 
Testing and Materials Standard (ASTM A240/A240M), having ANY of 
the dimensions listed in THE TABLE;
                         THE TABLE
  TYPE            GRADE  DIAMETER  INSIDE LENGTH  INSIDE WIDTH
  (a) short link   316     6.00 mm     18.60 mm       9.00 mm
  (b) short link   316     8.00 mm     24.20 mm      11.50 mm
  (c) short link   316     9.90 mm     30.40 mm      14.20 mm
  (d) short link   304     8.00 mm     24.00 mm      11.00 mm
  (e) short link   304    10.00 mm     29.20 mm      14.30 mm
  (f) medium link  316     2.00 mm     14.80 mm       4.25 mm
  (g) medium link  316     3.00 mm     15.60 mm       7.20 mm
  (h) medium link  316     3.90 mm     20.08 mm       6.65 mm
  (i) medium link  316     5.00 mm     22.00 mm       9.40 mm
  (j) medium link  316     6.00 mm     27.30 mm       9.75 mm
  (k) medium link  316     8.03 mm     31.70 mm      13.80 mm
  (l) medium link  316     9.90 mm     38.90 mm      14.05 mm
  (m) medium link  316    11.90 mm     47.20 mm      18.50 mm
  (n) medium link  316    16.00 mm     59.00 mm      24.50 mm
  (o) medium link  304     3.00 mm     15.60 mm       7.20 mm
  (p) medium link  304     3.95 mm     18.60 mm       7.15 mm
  (q) medium link  304     6.00 mm     26.80 mm      10.40 mm
  (r) medium link  304     7.88 mm     32.10 mm      13.95 mm
  (s) medium link  304    10.00 mm     38.90 mm      16.30 mm 
  (t) medium link  304    11.80 mm     46.50 mm      19.02 mm
For the purpose of this Order a tolerance of plus 2% or minus 2% 
is allowable on all dimensions

CHAINS, LIFTING, stainless steel, with OR without ANY of the 
following:
  (a) chain master links;
  (b) chain shackles;
  (c) chain hooks;
  (d) chain information tags;
  (e) chain shortener links

CHAINS, ANCHOR, studless, diameter NOT less than 81 mm

COMPENSATION CABLES, ELEVATOR, having BOTH of the following:
  (a) low carbon steel welded chain-link construction;
  (b) flame retardant PVC sheathes

CHAIN, LONGWALL MINING HAULAGE, having ALL of the following:
   (a) compliance with Standard DIN 22252;
   (b) link diameter NOT less than 18 mm;
   (c) pitch NOT less than 64 mm

CHAINS, ball, nickel plated, imported with OR without clips and/or
 plastic strap

CHAIN, ARMOURED FACE CONVEYOR AND/OR BEAM STAGE LOADER, having 
BOTH of the following:
  (a) link diameter NOT Less than 33 mm;
  (b) pitch NOT less than 110 mm

CHAINS, TENSION AND WEIGHT, with shackles

CHAIN, BEAD, stainless

CHAIN, LONGWALL MINING HAULAGE, having ALL of the following:
   (a) compliance with Standard DIN 22252;
   (b) link diameter NOT less than 18 mm;
   (c) pitch NOT less than 64 mm

PARTS, TYRE PROTECTION OR TYRE TRACTION CHAIN, as follows:
   (a) lugs;
   (b) hooks;
   (c) pin locks;
   (d) tubes;
   (e) links

CHAIN, split links

SUCTION ANCHORS, subsea, with OR without trunnion pins, 
including ALL of the following:
  (a) bull eyes;
  (b) mooring chain;
  (c) shackle;
  (d) receptacle;
  (e) lifting rigging;
  (f) monkey fists;
  (g) beta pins;
  (h) chain locking pin stab

SUCTION ANCHORS, subsea, including ALL of the following:  
  (a) shackle; 
  (b) mooring chain; 
  (c) vent plugs

ANCHORS, having BOTH of the following:
  (a) weight NOT less than 230 kg;
  (b) proof test load NOT less than 8 000 kg

BRADS, stainless steel, collated

WEDGES, steel, picture frame, collated in sets

PINS, upholstery, having ALL of the following:
   (a) domed head;
   (b) shank dia NOT less than 1.4 mm;
   (c) shank length NOT less than 13.0 mm when measured from the
       underside of the head

PINS, upholstery, spiral shank

BRADS, headless, cement coated

NAILS, CARPET GRIPPER MACHINE, being ANY of the following:
   (a) pin;
   (b) concrete;
   (c) ring shank

NAILS, CORRUGATED

NAILS, V contoured, with lipped edges

NAILS, COIL, wire welded collated

FASTENERS, INSULATION, incorporating a nail

TIES, WALL, helical, stainless steel, having a diameter NOT less 
than 6 mm and NOT greater than 10 mm

NAILS, having finish coating, being ANY of the following:
  (a) electro-galvanised coil nails;
  (b) hot dipped galvanised coil nails;
  (c) stainless steel coil nails;
  (d) coil nails having not less than 1 000 nails per coil

SPIKES, CONCRETE AND/OR BLOCK AND/OR BRICK AND/OR STONE, zinc 
coated carbon steel

NAILS OR BRADS OR TACKS OR FENCING STAPLES OR CLOUTS, but not 
including- 
Paper collated strip nails, or wire welded collated coil nails 
or machine driven loose nails.

ANCHORS, CONCRETE AND/OR MASONRY, being pins and/or nail-ins 
having individual expanding nylon or expanding metal casing, but 
NOT including powder actuated tool pins and nails

COACH SCREWS, rectangular OR square head, electroplated OR zinc 
galvanized carbon steel

COACH SCREWS, HEXAGONAL HEAD, having a composition of EITHER of 
the following:
  (a) electroplated OR zinc galvanised carbon steel;
  (b) stainless steel

SCREWS, WOOD, yellow zinc coated AND/OR stainless steel AND/OR 
galvanised steel, with OR without seals

SCREWS, TIMBER OR WOOD, galvanized OR zinc coated, low density 
polyethylene strip collated

SCREWS, WOOD, carbon steel OR stainless steel, with OR without 
plating, having BOTH of the following:
  (a) partially serrated thread;
  (b) star shaped indented screw head

SCREWS, type 17, unfinished, 12 gauge OR 14 gauge, NOT including 
ANY of the following kind:
  (a) plating;
  (b) painting;
  (c) washers

SCREWS, WOOD, yellow zinc coated carbon steel AND/OR zinc/tin 
coated carbon steel AND/OR stainless steel, with or without 
seals, having a screw gauge number NOT less than 7(shank 
diameter 3.8 mm) and NOT greater than 14(shank diameter 6.1 mm), 
having EITHER of the following:
  (a) length NOT less than 25 mm and NOT greater than 45 mm;
  (b) length NOT less than 65 mm and NOT greater than 300 mm

SCREWS, WOOD, polypropylene strip collated

SCREWS, CHIPBOARD, carbon steel, zinc coated

SCREWS, CHIPBOARD, being EITHER of the following:
  (a) carbon steel yellow zinc coated;
  (b) carbon steel class 3 coated

SCREWS, self-tapping, having ALL of the following:
  (a) bimetal hardened steel tip;
  (b) stainless steel body AND head; 
  (c) flake zinc silver surface

SCREWS, yellow zinc plated OR galvanised, with OR without washer

SCREWS, self-drilling, unplated, with OR without washers, having 
a surface hardness NOT less than 450 HV

SCREWS, self-tapping, consisting of BOTH of the following:
  (a) stainless steel body AND head;
  (b) hardened carbon steel tip

SCREWS, carbon steel, with OR without zinc coating, polyethylene 
strip collated

SCREWS, METAL, self drilling, yellow zinc coated carbon steel 
AND/OR zinc/tin coated carbon steel AND/OR stainless steel, with 
or without seals, having a screw gauge number NOT less than 
8(shank diameter 4.2 mm) and NOT greater than 14(shank diameter 
6.1 mm), having a length NOT less than 100 mm and NOT greater 
than 300 mm

SCREWS, SELF-TAPPING, polypropylene strip collated

SCREWS, self drilling, needle point, with OR without washers, 
being ANY of the following:
  (a) carbon steel yellow zinc coated;
  (b) carbon steel chrome coated;
  (c) carbon steel class 3 coated;
  (d) carbon steel class 4 coated

SCREWS, self-tapping, comprising BOTH of the following:
  (a) body and head of stainless steel;
  (b) tip of martensitic steel

PARTS FOR VEHICLES which, if imported, would fall within Chapter
 87 of the Customs Tariff Act 1987, being parts which are 30 years
 old or more
   For the purposes of TC 8533479 it is the importer"s
   responsibility to establish that the parts were manufactured
   30 years or more prior to the date of importation

BOLTS, CONNECTING, having ALL of the following:
   (a) body length 24 mm OR 34 mm;
   (b) thread length 7.5 mm, 11 mm, 11.5 mm, 12 mm, OR 15 mm;
   (c) M4, M6 OR  harpoon thread;
   (d) half round head

PARTS, PASSENGER MOTOR VEHICLE, manufactured at least 30 years
 before the goods are entered for home consumption, or reproductions
 of these parts, being screws and bolts, whether or NOT including
 nuts and washers

HOSE CLAMP COMPONENTS, WORM DRIVE, being ANY of the following:
   (a) buttress type threaded, rolled right hand screws meeting ALL
       of the following specifications:
          (i) socket head size within the range of 6.14 mm to 6.35 mm
              AF inclusive;
         (ii) head depth within the range of 4.95 mm to 5.42 mm
              inclusive;
        (iii) thread form length within the range of 7.49 mm to
              8.39 mm inclusive;
         (iv) major diameter within the range of 5.84 mm to 6.08 mm
              inclusive;
          (v) minor diameter within the range of 3.7 mm to 3.87 mm
              inclusive;
         (vi) flank angle of 13 degrees + or - 2 degrees;
        (vii) back angle of 2 degrees + or - 2 minutes;
       (viii) pitch within the range of 2.01 mm to 2.05 mm inclusive;
         (ix) flat root width within the range 1.27 mm to 1.33 mm
              inclusive;
          (x) bearing surface diameter within the range of 2.97 mm to
              3.18 mm inclusive;
   (b) rolled right hand thread screws meeting ALL of the following
       specifications:
          (i) socket head size within the range of 7.74 mm to 7.93 mm
              AF inclusive;
         (ii) head depth within the range of 8.00 mm to 8.26 mm
              inclusive;
        (iii) thread form length within the range of 17.00 mm to
              17.53 mm inclusive;
         (iv) major diameter within the range of 8.38 mm to 8.90 mm
              inclusive;
          (v) minor diameter within the range of 5.84 mm to 6.05 mm
              inclusive;
         (vi) flank angle of 20 degrees + or - 2 degrees;
        (vii) back angle of 2 degrees + or - 2 minutes;
       (viii) pitch within the range of 2.51 mm to 2.57 mm inclusive;
         (ix) flat root width within the range of 1.44 mm to 1.53 mm
              inclusive;
          (x) bearing surface diameter, at opposite end to screw
              head, within the range of 5.08 mm to 5.29 mm inclusive;
         (xi) bearing surface width, at opposite end to screw head,
              within the range of 1.78 mm to 2.29 mm inclusive,
   (c) single start rolled right hand thread screws meeting ALL of
       the following specifications:
          (i) complete across head screw slot, located across head
              flats, having a slot width measurement within the range
              of 1.52 mm to 1.63 mm inclusive;
         (ii) head depth within the range of 7.08 mm to 8.00 mm
              inclusive;
        (iii) thread form length within the range of 10.52 mm to
              22.93 mm inclusive;
         (iv) major diameter within the range of 7.56 mm to 7.94 mm
              inclusive;
          (v) minor diameter within the range of 5.80 mm to 6.12 mm
              inclusive;
         (vi) thread angle of 10 degrees;
        (vii) flat crest width within the range of 0.71 mm to 0.75 mm
              inclusive;
       (viii) modified ACME thread of 14 threads per 25.4 mm;
         (ix) bearing surface diameter, underneath screw head, within
              the range of 5.80 mm to 6.10 mm inclusive;
          (x) bearing surface width, underneath screw head, within
              the range of 1.52 mm to 2.06 mm inclusive

PARTS, PASSENGER MOTOR VEHICLE, manufactured at least 30 years
 before 16 August 1995, or reproductions of these parts, being screws
 and bolts, whether or NOT including nuts and washers

SCREWS, button head, socket, ISO metric, to specification BS4168

SCREWS, button head, socket, imperial, to specifications UNC/2BA
 BSW/BSF/UNF and BS2470

SCREWS, shoulder, socket, ISO metric, to specification BS4168

SCREWS, shoulder, socket, imperial, to specifications BSW/BSF/UNC
 and BS2470

SCREWS, socket head, stainless steel, metric, to specification
 plain cup point DIN 916

SCREWS, button head, socket, stainless steel, ISO metric, to
 specification BS 4168

SCREWS, being ANY of the following:
   (a) hexagon flange, 70 tooth head, property class 12.9;
   (b) cap screws, hexagon head, grade 10.9;
   (c) cap screw, flanged 12 point head, grade 8

BOLTS AND WASHERS, high tensile steel grade 10.9, having an
outer bolt thread length NOT less than 105 mm

BOLTS, steel, having BOTH of the following:
  (a) 9 inches in length with 1/1/4 inch thread pitch;  
  (b) 12-point head

BOLTS, SQUARE NECK SPRING, steel, having BOTH of 
the following:
  (a) thread size NOT less than 24 mm;
  (b) length NOT less than 166 mm

FASTENERS, being lockbolts AND/OR collars

U-BOLTS AND/OR SPRING CLAMPS, heat treated high tensile steel, 
having a weight NOT less than 2 kg

WHEEL STUDS, having BOTH of the following:
  (a) thread pitch distance 22 mm x 1.5 mm AND/OR 22 mm x 2 mm;
  (b) length NOT less than 80 mm

FASTENERS, GRINDING MILLS, having ALL of the following:
  (a) bolts;
  (b) nuts;
  (c) washers;
  (d) mechanical tensioner nut

SCREW ANCHORS, CONCRETE AND/OR MASONRY, being ANY of the 
following:
  (a) zinc flake coated steel;
  (b) zinc plated steel;
  (c) stainless steel;
  (d) high corrosion resistant steel

REPAIR KITS, DISC BRAKES, consisting of BOTH of the following:
  (a) caps;
  (b) cylinder head screws

SCREW ANCHORS, MASONRY, button OR flat head, having BOTH of the 
following:
  (a) stainless steel;  
  (b) hardened carbon steel tip

ANCHORS, MASONRY, having a serrated hex flange head, being ANY 
of the following:
  (a) electroplated zinc;
  (b) galvanised zinc;
  (c) stainless steel;
  (d) mechanical galvanised

KITS, PURLIN ASSEMBLY, mild steel OR high tensile steel, zinc 
plated and galvanised, with OR without washers, being EITHER of 
the following:
  (a) hex bolts and nuts;
  (b) hex flanged bolts and flanged nuts

BOLT ASSEMBLIES, high tensile steel, hot dipped, galvanised, 
complying with Australian/New Zealand Standard 1252:1996 (AS/NZS 
1252:1996), being All of the following:
  (a) bolts;
  (b) nuts;
  (c) washers

ANCHORS, MASONRY, threaded stud, being ANY of the following:
  (a) electroplated zinc;
  (b) galvanized zinc;
  (c) stainless steel

BOLTS, mushroom head, carbon steel, electroplated OR zinc 
galvanised, with OR without EITHER of the following:
  (a) nuts AND/OR washers;
  (b) epoxy resin coating

BOLTS, CUP AND/OR HEXAGONAL HEAD, stainless steel, with OR 
without nuts AND/OR washers

BOLTS, CUP AND/OR HEXAGONAL HEAD, carbon steel, electroplated OR 
zinc galvanised, with OR without EITHER of the following:
  (a) nuts AND/OR washers;
  (b) epoxy resin coating

ANCHORS, CONCRETE AND/OR MASONRY, being ANY of the following:
  (a) hollow wall anchors;
  (b) socket anchors;
  (c) internally threaded anchors

SCREWS, WALLBOARD AND/OR MASONRY AND/OR TIMBER, carbon steel, 
chrome plated AND/OR zinc plated AND/OR zinc tin plated, having 
ALL of the following:
  (a) pan head;
  (b) screw gauge NOT greater than 8 mm;
  (c) length NOT less than 32 mm and NOT greater 50 mm

STACKING BOLTS, having female threaded heads

SCREWS, nylon plug fitted, being EITHER of the following:
  (a) type 17 point;
  (b) carbon zinc coated or galvanised or stainless steel

ANCHORS, MOORING BOLLARD

ANCHORS, THREADED STUD, stainless steel, having ALL of the 
following:
  (a) diameter not less than 19.7 mm;
  (b) length not less than 395 mm;
  (c) threaded length not less than 30 mm

ANCHORS, THREADED STUD, zinc plated, high tensile steel, having 
ALL of the following:
  (a) diameter NOT less than 20 mm;
  (b) length NOT less than 225 mm;
  (c) threaded length NOT less than 50 mm

SCREWS, FOUNDATION, steel

BOLTS, HOLLOW INJECTION

BOLTS, SELF LOCKING, hexagon head, ISO metric property class 12.9

PARTS FOR VEHICLES which, if imported, would fall within Chapter
 87 of the Customs Tariff Act 1987, being parts which are 30 years
 old or more
   For the purposes of TC 8732362 it is the importer"s
   responsibility to establish that the parts were manufactured
   30 years or more prior to the date of importation

NUTS, stainless steel, coated with an alloy of chromium, nickel
 and tungsten

NUTS, pre-tension, incorporating socket screws

NUTS, hydraulic clamping, incorporating a pressure ring and a
 hydraulic chamber within the body of the nut

NUTS, bearing adjusting, having a shaped surface to permit
 adjustment to compensate wear in the bearing, weight NOT less
 than 1 kg

NUT, M22 x 1.5, having a two piece construction consisting of a
 33mm hex head nut and a captive washer

WHEEL NUTS, having All of the following:
  (a) tapered;
  (b) closed end;
  (c) thread 1/2"

WHEEL NUTS, having All of the following:
  (a) narrow shank;
  (b) closed end;
  (c) thread 7/16"

WHEEL NUTS, having ANY of the following:
  (a) NOT less than 4 in a pack;
  (b) tapered slimline AND/OR tapered AND/OR tapered shank;
  (c) open AND/OR closed end;
  (d) locking;
  (e) thread sizes being ANY of the following: 
          (i) M12 x 1.25;
         (ii) M12 x 1.50;
        (iii) M14 x 1.50

WHEEL NUTS, having ALL of the following:
  (a) chrome finish;
  (b) closed end;
  (c) M12 x 1.25 tapered thread

NUTS, PIVOT, ROOF RACK, cast carbon steel

NUTS, being EITHER of the following:
  (a) hex, galvanized OR zinc plated;
  (b) dome, chrome steel

NUTS, being ANY of the following:
  (a) hex flanged torque nuts;
  (b) hex flanged weldnuts;
  (c) square nuts;
  (d) round nuts;
  (e) hex nuts class 4;
  (f) hex flanged captive washer nuts;
  (g) spring nuts;
  (h) hex wizlock nuts;
  (i) nyloc nuts;
  (j) hex nuts class 8;
  (k) square weldnuts;
  (l) serrated flanged nuts;
  (m) hex conelock nuts

NUT INSERTS, threaded, steel or stainless steel

LOCK NUTS, NYLON INSERT, silver zinc passivated, having at least 
three of the following:
  (a) thread diameter NOT less than 19 mm and NOT greater than 
      52 mm;
  (b) pitch NOT less than 2.5 mm and NOT greater than 6 mm;
  (c) threads per 25.4 mm (1 inch) NOT less than 4 and NOT 
      greater than 10;
  (d) hardness NOT less than 245 HV and NOT greater than 325 HV

NUTS, COUPLING, cast iron, having BOTH the following:
  (a) internal diameter NOT greater than 50 mm;
  (b) outside flange diameter NOT greater than 91 mm

RAIL NUTS

NUTS, hot forged, having ALL of the following:
  (a) internal diameter NOT less than 24 mm;
  (b) height NOT less than 30 mm;
  (c) diameter NOT less than 35 mm

FASTENERS, self clinching

DOWEL PINS, mounting plate

FASTENERS, NAIL SCREW, with nail point, with OR without washers, 
having ALL of the following:
  (a) plastic OR wire coil collation;
  (b) corrosion resistant AND/OR friction resistant coatings;
  (c) screw removable

RODS, threaded, being EITHER of the following:
  (a) zinc plated;
  (b) galvanized zinc

SCREWS, each screw having a nylon expansion screw anchor sleeve

DOWEL PINS, steel, threaded

PARTS FOR VEHICLES which, if imported, would fall within Chapter
 87 of the Customs Tariff Act 1987, being parts which are 30 years
 old or more
   For the purposes of TC 8732363 it is the importer"s
   responsibility to establish that the parts were manufactured
   30 years or more prior to the date of importation

WASHERS, compression, to DIN Specification 6796

RINGS, snap, having a radial single pitch axial inner cut-out
 of 4 mm or greater but NOT exceeding 38 mm

WASHERS, SECURING, BOLT, with cams

PARTS FOR VEHICLES which, if imported, would fall within Chapter
 87 of the Customs Tariff Act 1987, being parts which are 30 years
 old or more
   For the purposes of TC 8732364 it is the importer"s
   responsibility to establish that the parts were manufactured
   30 years or more prior to the date of importation

WASHERS, DOME BALL, hot forged, having ALL of the following:
  (a) external diameter NOT less than 49 mm;
  (b) height NOT less than 15 mm;
  (c) internal diameter NOT less than 24.5 mm

PARTS FOR VEHICLES which, if imported, would fall within Chapter
 87 of the Customs Tariff Act 1987, being parts which are 30 years
 old or more
   For the purposes of TC 8732365 it is the importer"s
   responsibility to establish that the parts were manufactured
   30 years or more prior to the date of importation

RIVETS, STEEL, SELF PIERCING

RIVETS, steel, NOT less than 76 mm and NOT greater than 254 mm long

PARTS FOR VEHICLES which, if imported, would fall within Chapter
 87 of the Customs Tariff Act 1987, being parts which are 30 years
 old or more
   For the purposes of TC 8732366 it is the importer"s
   responsibility to establish that the parts were manufactured
   30 years or more prior to the date of importation

PINS, spring tension, ISO metric or imperial

COTTER-PINS, SAFETY LOCKING

PINS, steel, spring coiled

PINS, spring steel, tubular, longitudinally split

KEYS, woodruff

FASTENERS, vibration movement resistant, being non threaded
 grooved pins and/or swaging collars

SHEAR CONNECTORS, carbon steel, non-threaded, headed, complying 
with EITHER of the following:
  (a) Australian/New Zealand Standard 1554.2 (AS/NZS 1554.2);
  (b) Deutsches Institut Fur Normung Standard EN ISO 13918 (DIN 
      EN ISO 13918)

LIFTING ANCHORS, steel, non-threaded, being EITHER of the 
following:
  (a) spherical-head lifting anchor;
  (b) eye anchor

DOWEL PINS, steel, non-threaded

GRAB RINGS, stainless steel

LEAF SPRINGS, tapered, single construction, spring steel, comprising
 ALL of the following:
   (a) z contoured;
   (b) length NOT less than 1 130 mm and NOT exceeding 1 252 mm;
   (c) thickness NOT less than 38 mm and NOT exceeding 52 mm;
   (d) capacity NOT less than 4 t and NOT exceeding 5.25 t

PARTS, PASSENGER MOTOR VEHICLE, manufactured at least 30 years
 before the goods are entered for home consumption, or reproductions
 of these parts, being ANY of the following:
  (a) leaf springs;
  (b) leaf spring leaves

LEAF SPRINGS, tapered, cranked, incorporating a bush-eye, having a
 gross capacity of 8 T or greater

LEAF SPRINGS, TRAILER AIR SUSPENSION, straight OR cranked, with 
OR without spring bush-eyes, including BOTH of the following:
  (a) maximum spring load NOT less than 2.5 tonnes;
  (b) single OR double layered

TRAILING ARMS, TRAILER AIR SUSPENSION, steel, having a net arm 
weight NOT less than 15 kg

LEAF SPRINGS, parabolic, having BOTH of the following:
(a)maximum of two leaves;
(b)gross capacity NOT less than 10 t

PARTS FOR VEHICLES which, if imported, would fall within Chapter
 87 of the Customs Tariff Act 1987, being parts which are 30 years
 old or more
   For the purposes of TC 8732367 it is the importer"s
   responsibility to establish that the parts were manufactured
   30 years or more prior to the date of importation

SPRINGS, die, chrome vanadium, to Specification SAE 6150, being
 helical springs made from wire of rectangular cross-section with
 rounded corners

SPRINGS, tungsten steel

PARTS, PASSENGER MOTOR VEHICLE, manufactured at least 30 years
 before the goods are entered for home consumption, or reproductions
 of these parts, being helical springs

PARTS, PASSENGER MOTOR VEHICLE, manufactured at least 30 years
 before 16 August 1995, or reproductions of these parts, being
 helical springs

SPRINGS, HELICAL VOLUTE, FURNACE, having a maximum spring load 
capacity NOT less than 350 kN

WASHERS, disc spring (belleville), to DIN Specification 2093

PARTS, PASSENGER MOTOR VEHICLE, manufactured at least 30 years
 before the goods are entered for home consumption, or reproductions
 of these parts, being springs but NOT including leaf or helical
 springs

SPRINGS, recoil and extension, having a fatigue life of 40,000
 cycles or greater

PARTS, TRAILER DRUM BRAKE, being axle return springs

COOKERS, GAS, single burner, having BOTH of the following:
   (a) weight excluding fuel NOT exceeding 1.8 kg;
   (b) piezo electric ignition

STOVES, butane gas, portable, single burner, having ALL the
 following:
   (a) weight less than 2 kg;
   (b) piezo ignition;
   (c) variable heat control;
   (d) pressure sensitive safety cut off;
   (e) maximum heat output 8 MJ/h

COOKERS, SINGLE BURNER, PORTABLE, CYLINDER MOUNTED, PROPANE GAS,
 weight NOT exceeding 850 gms, but NOT including cookers imported
 with gas cylinders

GRILLERS, gas

COOKTOPS, gas, including ALL of the following:
  (a) round heat shields;
  (b) ignitors;
  (c) control knobs;
  (d) burners with pan supports;
  (e) flanges

COOKERS, propane gas AND/OR butane gas fired, single burner, 
cylinder mounted, foldable, having BOTH of the following:
  (a) weight NOT greater than 100 g;
  (b) with OR without carry bag

COOKTOPS, GAS, with OR without wok burners, having BOTH of the 
following:
  (a) NOT more than 6 burners;
  (b) width NOT greater than 90 cm

COOKERS, GAS, portable, electronic, having a weight excluding 
fuel NOT greater than 9 kg

GRILLS AND/OR STOVES, FOLD UP

STOVES, oil or spirit, single burner type, having a weight NOT
 exceeding 1.7 kg

STOVES, DIESEL, having a heating capacity NOT greater than 1.9 kW

SETS, FONDUE, comprising ALL of the following:
  (a) burner;
  (b) stand;
  (c) pot,
and including ANY of the following:
  (a) wire rack;
  (b) diffuser;
  (c) lazy susan;
  (d) tray;
  (e) dishes;
  (f) forks;
  (g) fork guards;
  (h) spoons;
  (i) spatulas

STOVE SETS, portable, solid fuel, including ALL of the 
following:
  (a) chimney sections, having a flue diameter NOT greater 
      than 62 mm;    
  (b) spark arrestor;
  (c) four galvanised threaded legs;
  (d) mesh floor fire grate;
  (d) barbecue plates;
  (e) plate lift handle;
  (f) steel body, having ALL of the following:
         (i)   NOT less than 200 mm diameter cooking opening;
        (ii)  NOT less than 170 mm diameter feed inlet;
       (iii) cylindrical mid-portion AND rounded ends

COOKERS, WOOD PELLET BARBEQUE, including BOTH of the following:
  (a) auger fed burner;
  (b) electronic starter

RADIATORS, CAMPING, PORTABLE, CYLINDER MOUNTED, PROPANE GAS, weight
 NOT exceeding 550 gms, but NOT including radiators imported with gas
 cylinders

RADIATORS, CAMPING, PORTABLE, BUTANE GAS

FIREPLACES, GAS, direct vent

HEATERS, space, liquid fuel, domestic, portable, which do NOT
 require connection to any external fuel source or electricity supply

FIREPLACES, bio-ethanol

HEATERS, WOOD PELLET, having ALL of the following:
  (a) filling capacity NOT less than 5 kg; 
  (b) integrated ash bin;
  (c) fire starters AND matches; 
  (d) cleaning brush AND gloves

HEATERS, WOOD PELLET, including ALL of the following:
  (a) electric fans;
  (b) remote control;
  (c) humidifier

PARTS, RADIANT AND/OR CONVECTION GAS HEATER, being ANY of the 
following:
  (a) air diffusers;
  (b) back plates;
  (c) burner boxes;
  (d) burner injector supports;
  (e) burner injector rails;
  (f) burner injector strips;
  (g) burner supports;
  (h) covers;
  (i) cover strips;
  (j) dress guards;
  (k) fan ducts;
  (l) motor guards;
  (m) front facia panels;
  (n) gutter strips;
  (o) louvers and blades;
  (p) reflectors;
  (q) sparker tabs;
  (r) top baffles;
  (s) valve supports

PARTS, OVEN AND/OR GRILLER, being ANY of the following:
   (a) aeration shutters;
   (b) boxes;
   (c) braces;
   (d) burners;
   (e) buttons;
   (f) caps;
   (g) channels;
   (h) clamps;
   (i) covers;
   (j) ducts;
   (k) gas tubes;
   (l) griddle and/or grill dishes and/or trays;
   (m) guards;
   (n) hotplates;
   (o) interfaces;
   (p) panels;
   (q) pipe manifolds;
   (r) plates;
   (s) printed circuit boards;
   (t) racks;
   (u) rails;
   (v) runners;
   (w) shelves;
   (x) shields;
   (y) supports;
   (z) trims;
  (aa) vents

TRIVETS, GAS COOKER

RACKS AND/OR SHELVES, OVEN AND/OR GRILLER

PANEL RADIATORS, pressed steel, with convectors

AIR HEATERS, GAS AND/OR OIL, including ALL of the following:
  (a) combustion chamber;
  (b) ceramic inner lining;
  (c) temperature gauges;
  (d) pipes;
  (e) mixing chamber

HEATERS, WOOD PELLET, fresh air intake, temperature controlled

STEAM HEATERS, FRENCH FRY DRYER, including ALL of the following:
  (a) tubes;
  (b) fins;
  (c) manifolds;
  (d) maximum capacity exceeding 380 000 kcal/hour;
  (e) maximum capacity exceeding 440 kW

HEATERS, gas, having ALL of the following:
  (a) control panel;
  (b) heating power NOT less than 1 300 W and NOT greater than 
      3 700 W;
  (c) fan

HEATERS, mobile, diesel fuelled, fan forced

AIR HEATERS, whether OR not assembled, including ALL of the 
following:
  (a) steel tube bundle;
  (b) burning chamber;
  (c) flue gas fan;
  (d) recirculation duct;
  (e) flue gas pressure limit switch;
  (f) flue gas pressure manometer;
  (g) air pressure drop manometer;
  (h) burning chamber temperature limit switch;
  (i) flue gas temperature limit switch

AIR HEATING SYSTEM, concrete curing, including ALL of the 
following:
  (a) gas burners;
  (b) air fans;
  (c) duct mixers;
  (d) control dampers;
  (e) humidity control atomized water system

HEATERS, liquid petroleum gas AND/OR natural gas

PARTS, AIR HEATER, waste oil fuelled, being ANY of the following:
  (a) heating cabinets;
  (b) burners;
  (c) pilot rings;
  (d) burner basin;
  (e) vaporising pans

AIR HEATERS, liquid petroleum gas (LPG) fuelled

HEATERS, AIR, waste oil fuelled

HEATERS, RADIANT TUBE, infra-red, gas fired

AIR HEATERS, DIESEL OR PETROL, having an output heat rating
 NOT exceeding 10 kW

COOKWARE, ASSORTED, whether OR not as sets, with OR without lids 
AND/OR non-stick coating, having two or more of the following:
  (a) milk pans;
  (b) saucepans;
  (c) universal steamers;
  (d) casserole dishes AND/OR pots;
  (e) dutch AND/OR french ovens;
  (f) steamer inserts;
  (g) stock pots;
  (h) fry pans;
  (i) pasta inserts;
  (j) steamer baskets;
  (k) roasters;
  (l) baking dishes AND/OR pans;
  (m) oven pans;
  (n) saute pans;
  (o) chefs pans;
  (p) woks;
  (q) grills;
  (r) griddles;
  (s) stew pots;
  (t) roasting pans with rack;
  (u) double boilers
For the purpose of this order %EF%BF%BD%EF%BF%BD%EF%BF%BDsets%EF%BF%BD%EF%BF%BD%EF%BF%BD includes two or more 
articles put up together

COOKWARE, enamelled cast iron, being ANY of the following:
  (a) dutch ovens with OR without lids;
  (b) saute pans with OR without lids;
  (c) sauce pans with OR without lids;
  (d) braisers with OR without lids;
  (e) grill skillets;
  (f) baking dishes;
  (g) roasting dishes with OR without lids;
  (h) fry pans;
  (i) grill trays

COOKWARE, with OR without non-stick coating, being 
ANY of the following:
   (a) casserole dishes, with OR without lids;
   (b) frypans, with OR without lids;
   (c) saucepans, with OR without lids;
   (d) baking dishes, with OR without lids;
   (e) grill pans AND plates;
   (f) skillets;
   (g) woks, with OR without lids;
   (h) steamers, with OR without lids;
   (i) oven pans, with OR without lids;
   (j) baking pans, with OR without lids;
   (k) Dutch AND/OR French ovens, with OR without lids;
   (l) double boilers, with OR without lids;
   (m) griddle pans, with OR without lids

TEAPOTS, cast iron, including BOTH of the following:
  (a) interior enamel coating;
  (b) stainless steel infuser or strainer

COFFEE MAKER, expresso, domestic, non-electric, but NOT including
 coffee making machines which are fitted for connection to mains
 water supply

BOBBINS, sewing machine

COOKWARE, STAINLESS STEEL, being ANY of the 
following:
  (a) cooking pans AND/OR pots;
  (b) baking pans AND/OR pots;
  (c) deep fryer baskets;
  (d) pasta pan AND/OR pot inserts;
  (e) braisers;
  (f) ramekins;
  (g) Dutch ovens,
with OR without ANY of the following:
           (i) aluminium cores;
          (ii) copper bases;
         (iii) non-stick coatings;
          (iv) lids;
           (v) silicone handles

PANS, EGG, having BOTH of the following:
  (a) separated cups;
  (b) lids

SETS, COOKWARE, consisting of two OR more saucepans with lids

TABLEWARE AND/OR KITCHENWARE, being ANY of the following:
  (a) food pans AND/OR steam pans;
  (b) food drain plates;
  (c) food pan lids

COOKWARE, with OR without lids AND/OR taps being EITHER of the 
following;
  (a) stockpots;
  (b) saucepots

COOKWARE, with OR without lids AND/OR non-stick coating, 
consisting ONLY of articles of two OR more of the following 
categories, whether OR not as sets: 
  (a) saucepan;
  (b) frying pan;
  (c) casserole pan;
  (d) steamer basket AND/OR insert

CHAFING DISHES

COOKWARE, ASSORTED, whether OR not as sets, with OR without lids 
AND/OR non-stick coating, having two or more of the following:
  (a) milk pans;
  (b) saucepans;
  (c) universal steamers;
  (d) casserole dishes AND/OR pots;
  (e) dutch AND/OR french ovens;
  (f) steamer inserts;
  (g) stock pots;
  (h) fry pans;
  (i) pasta inserts;
  (j) steamer baskets;
  (k) roasters;
  (l) baking dishes AND/OR pans;
  (m) oven pans;
  (n) saute pans;
  (o) chefs pans;
  (p) woks;
  (q) grills;
  (r) griddles;
  (s) stew pots;
  (t) roasting pans with rack;
  (u) double boilers
For the purpose of this order %EF%BF%BD%EF%BF%BD%EF%BF%BDsets%EF%BF%BD%EF%BF%BD%EF%BF%BD includes two or more 
articles put up together

COOKWARE, with OR without non-stick coating, being 
ANY of the following:
   (a) casserole dishes, with OR without lids;
   (b) frypans, with OR without lids;
   (c) saucepans, with OR without lids;
   (d) baking dishes, with OR without lids;
   (e) grill pans AND plates;
   (f) skillets;
   (g) woks, with OR without lids;
   (h) steamers, with OR without lids;
   (i) oven pans, with OR without lids;
   (j) baking pans, with OR without lids;
   (k) Dutch AND/OR French ovens, with OR without lids;
   (l) double boilers, with OR without lids;
   (m) griddle pans, with OR without lids

COOKWARE, ASSORTED, with OR without non-stick coating, having 
two or more of the following:
  (a) milk-pan;
  (b) saucepan with OR without glass AND stainless steel lid;
  (c) multi cooker with OR without glass AND stainless steel lid;
  (d) universal steamer;
  (e) casserole with OR without glass AND stainless steel lid;
  (f) dutch oven with OR without glass AND stainless steel lid;
  (g) steamer insert;
  (h) stockpot with OR without glass AND stainless steel lid;
  (i) frypan;
  (j) skillet;
  (k) pasta insert;
  (l) vegetable steamer basket;
  (m) roaster with rack with OR without glass AND stainless    
      steel lid;
  (n) baking dish with rack with OR without glass AND stainless  
      steel lid;
  (o) oven pan with OR without glass AND stainless steel lid;
  (p) saute pan with OR without glass AND stainless steel lid;
  (q) chefs pan with OR without glass AND stainless steel lid;
  (r) wok pan with OR without glass AND stainless steel lid

COOKWARE, with OR without lids AND/OR non-stick coating AND/OR  
built in heat indicator, being ANY of the following:
  (a) frypans;
  (b) wok pans;
  (c) grill pans;
  (d) pot roasters;
  (e) saute pans;
  (f) saucepans

CHICKEN ROASTING STANDS, stainless steel

SMOKER BOXES, BARBEQUE, stainless steel, having ALL of the 
following:
  (a) slotted top;
  (b) length NOT greater than 22 cm;
  (c) height NOT greater than 4 cm

SETS, CAKE DECORATING, consisting of BOTH of the following:
  (a) icing tips;
  (b) coupler

UTENSILS, HOUSEHOLD, stainless steel, being ANY of the 
following:
   (a) baskets; 
   (b) bottle baskets; 
   (c) buckets; 
   (d) candle snuffers;
   (e) child safety gates; 
   (f) coal scuttles or hods; 
   (g) cotton bud dispenser boxes; 
   (h) dustbins; 
   (i) eye baths; 
   (j) flower boxes or planters;
   (k) hot water bottles; 
   (l) letter boxes;
   (m) luncheon boxes; 
   (n) movable boot scrapers; 
   (o) plant pots or hanging planters or plant tubs or plant 
       muck boxes or plant saucers;  
   (p) plant movers;
   (q) plate stands; 
   (r) rubbish bins with or without plastic inner bucket;
   (s) shoe trees; 
   (t) flat irons stands; 
   (u) storage boxes or storage bins or storage tins; 
   (v) tissue paper holders or enclosures;
   (w) magazine holders; 
   (x) wash basins; 
   (y) watering cans; 
   (z) wine racks

KETTLES, STOVE TOP

KITCHENWARE, stainless steel, being ANY of the 
following:         
   (a) bag dispensers;
   (b) bottles;
   (c) bowls;
   (d) bread bins;
   (e) canisters;
   (f) capacity measurers;
   (g) colanders;
   (h) cutlery or kitchen utensils stands and/or racks and/or 
trays;
   (i) dish drainers and/or dish drying racks;
   (j) milk cans;
   (k) double boilers and/or inserts;
   (l) fish kettles;
   (m) food or cake domes;
   (n) funnels;
   (o) glass racks;
   (p) gridirons;
   (q) grilling racks;
   (r) hob guards;
   (s) wrapping holders and/or foil holders;
   (t) jelly or pastry moulds;
   (u) jugs;
   (v) kettles;
   (w) knife boxes or knife racks;
   (x) non electric coffee pots and/or percolators; 
   (y) paper towel holders;
   (z) pasta inserts;
  (aa) plate racks or holders;
  (ab) preserving pans or jars;
  (ac) pressure cookers;
  (ad) rinsing baskets or strainers;
  (ae) salad washers;
  (af) pressure cooker separating compartments;
  (ag) shakers;
  (ah) sink cover plates;
  (ai) spice or condiments racks and/or stands;
  (aj) splatter screens or guards;
  (ak) food bowl stands;
  (al) steamers and/or inserts;
  (am) storage tins and/or storage jars and/or storage caddies;
  (an) sugar tins;
  (ao) suspension rails;
  (ap) tea infusers;
  (aq) trivets;
  (ar) wine racks

HOUSEHOLD ARTICLES, being charcoal chimney starters

STANDS AND/OR RESTS, SPOON, stainless steel, having a 
chrome wire support

BINS, HOUSEHOLD, having ALL of the following:
  (a) stainless steel body;
  (b) plastic internal bucket;
  (c) plastic lid;
  (d) ball bearing slides

BOTTLES, DRINKING, stainless steel, with OR without plastic 
closures

KITCHENWARE AND/OR SINK ACCESSORIES, being ANY of the following:
  (a) colanders;
  (b) draining baskets;
  (c) drainers;
  (d) in bench mounted waste bins;
  (e) food preparation board and colander sets

KITCHENWARE, stainless steel, being ANY of the following: 
  (a) cooling racks;
  (b) egg rings;
  (c) egg separators;
  (d) sandwich cutting guides

STRAINERS, FOOD OR DRINK, stainless steel

GUARDS, SAFETY, STOVE TOP, stainless steel

BOWLS, PET FOOD, stainless steel

TABLEWARE, stainless steel, being ANY of the following:
   (a) baskets; 
   (b) bottles; 
   (c) bowls; 
   (d) card holders; 
   (e) cruets;
   (f) cups; 
   (g) decanters; 
   (h) dishes; 
   (i) drip stoppers; 
   (j) egg cups; 
   (k) fondues; 
   (l) food or cake domes; 
   (m) non electric food warmers; 
   (n) ice buckets; 
   (o) jugs; 
   (p) knife or chopstick rests;
   (q) mugs; 
   (r) mustard pots;
   (s) napkin and/or place card stands; 
   (t) non electric coffee pots or percolators; 
   (u) plates; 
   (v) plate stands; 
   (w) platters or serving plates; 
   (x) salad bowls; 
   (y) salt cellars; 
   (z) salt or pepper shakers; 
  (aa) sauce boats; 
  (ab) saucers; 
  (ac) serviette or napkin rings; 
  (ad) tea pot stands or cake stands; 
  (ae) sugar basins or shakers; 
  (af) table cloth clips; 
  (ag) table place mats or coasters; 
  (ah) sugar bowls and/or milk jugs and/or trays; 
  (ai) tea infusers or tea honey sticks or tea dishes; 
  (aj) tea pots; 
  (ak) tea strainers; 
  (al) toast racks; 
  (am) trays; 
  (an) trivets; 
  (ao) tumblers; 
  (ap) tureens; 
  (aq) wine cooling buckets; 
  (ar) wine pouring cradles; 
  (as) wine bottle stands

MUGS, BEVERAGE, stainless steel, double walled

DISPENSERS, SYPHON, WHIPPED CREAM

COOKERS, pressure, stainless steel

INFUSERS, COFFEE

BAKEWARE, coil coated steel, being springform pans

COOKWARE, enamelled steel, being ANY of the following:
  (a) pots, with OR without lids;
  (b) roasting pans, with OR without lids;
  (c) frying pans, with OR without lids;
  (d) stove top pressure cookers;
  (e) cooking bowls, with OR without lids

UTENSILS, HOUSEHOLD, enamelled iron or steel, being ANY of the 
following:
   (a) baskets; 
   (b) bottle baskets; 
   (c) buckets; 
   (d) candle snuffers;
   (e) child safety gates; 
   (f) coal scuttles or hods; 
   (g) cotton bud dispenser boxes; 
   (h) dustbins; 
   (i) eye baths; 
   (j) flower boxes or planters;
   (k) hot water bottles; 
   (l) letter boxes;
   (m) luncheon boxes; 
   (n) movable boot scrapers; 
   (o) plant pots or hanging planters or plant tubs or plant
       muck boxes or plant saucers;  
   (p) plant movers;
   (q) plate stands; 
   (r) rubbish bins;
   (s) shoe trees; 
   (t) flat irons stands; 
   (u) storage boxes or storage bins or storage tins; 
   (v) tissue paper holders or enclosures;
   (w) magazine holders; 
   (x) wash basins; 
   (y) watering cans; 
   (z) wine racks

KITCHENWARE, enamelled iron or steel, being ANY of the following:
   (a) bag dispensers;
   (b) bottles;
   (c) bowls;
   (d) bread bins;
   (e) canisters;
   (f) capacity measurers;
   (g) colanders;
   (h) cutlery or kitchen utensils stands and/or racks and/or 
trays;
   (i) dish drainers and/or dish drying racks;
   (j) milk cans;
   (k) double boilers and/or inserts;
   (l) fish kettles;
   (m) food or cake domes;
   (n) funnels;
   (o) glass racks;
   (p) gridirons;
   (q) grilling racks;
   (r) hob guards;
   (s) wrapping holders and/or foil holders;
   (t) jugs;
   (u) kettles;
   (v) knife boxes or knife racks;
   (w) non electric coffee pots and/or percolators; 
   (x) paper towel holders;
   (y) pasta inserts;
   (z) plate racks or holders;
  (aa) preserving pans or jars;
  (ab) pressure cookers;
  (ac) rinsing baskets or strainers;
  (ad) salad washers;
  (ae) pressure cooker separating compartments;
  (af) shakers;
  (ag) sink cover plates;
  (ah) spice or condiments racks and/or stands;
  (ai) splatter screens or guards;
  (aj) food bowl stands;
  (ak) steamers and inserts;
  (al) storage tins and/or storage jars and/or storage caddies;
  (am) sugar tins;
  (an) suspension rails;
  (ao) tea infusers;
  (ap) trivets;
  (aq) wine racks

RACKS, carbon steel, being ANY of the following:
  (a) chrome plated;
  (b) non-stick coated;
  (c) foldable

TABLEWARE, enamelled iron or steel, being ANY of the following:
   (a) baskets; 
   (b) bottles; 
   (c) bowls; 
   (d) card holders; 
   (e) cruets;
   (f) cups; 
   (g) decanters; 
   (h) dishes; 
   (i) drip stoppers; 
   (j) egg cups; 
   (k) fondues; 
   (l) food or cake domes; 
   (m) non electric food warmers; 
   (n) ice buckets; 
   (o) jugs; 
   (p) knife or chopstick rests;
   (q) mugs; 
   (r) mustard pots;
   (s) napkin and/or place card stands; 
   (t) non electric coffee pots or percolators; 
   (u) plates; 
   (v) plate stands; 
   (w) platters or serving plates; 
   (x) salad bowls; 
   (y) salt cellars; 
   (z) salt or pepper shakers; 
  (aa) sauce boats; 
  (ab) saucers; 
  (ac) serviette or napkin rings; 
  (ad) tea pot stands or cake stands; 
  (ae) sugar basins or shakers; 
  (af) table cloth clips; 
  (ag) table place mats or coasters; 
  (ah) sugar bowls and/or milk jugs and/or trays; 
  (ai) tea infusers or tea honey sticks or tea dishes; 
  (aj) tea pots; 
  (ak) tea strainers; 
  (al) toast racks; 
  (am) trays; 
  (an) trivets; 
  (ao) tumblers; 
  (ap) tureens; 
  (aq) wine cooling buckets; 
  (ar) wine pouring cradles; 
  (as) wine bottle stands

BOBBINS, sewing machine

STANDS, PLATE, PLATTER, BOWL, OR COMBINED CUP, SAUCER AND PLATE

HANGERS, PLATE, sizes 5.1 cm to 60.9 cm inclusive, adjustable or non
 adjustable

BAKING TRAYS, carbon steel with non-stick coating

PANS, CAKE, carbon steel, with OR without non-stick coating

PANS, PIZZA

COOKWARE, ASSORTED, whether OR not as sets, with OR without lids 
AND/OR non-stick coating, having two or more of the following:
  (a) milk pans;
  (b) saucepans;
  (c) universal steamers;
  (d) casserole dishes AND/OR pots;
  (e) dutch AND/OR french ovens;
  (f) steamer inserts;
  (g) stock pots;
  (h) fry pans;
  (i) pasta inserts;
  (j) steamer baskets;
  (k) roasters;
  (l) baking dishes AND/OR pans;
  (m) oven pans;
  (n) saute pans;
  (o) chefs pans;
  (p) woks;
  (q) grills;
  (r) griddles;
  (s) stew pots;
  (t) roasting pans with rack;
  (u) double boilers
For the purpose of this order %EF%BF%BD%EF%BF%BD%EF%BF%BDsets%EF%BF%BD%EF%BF%BD%EF%BF%BD includes two or more 
articles put up together

COOKWARE, with OR without non-stick coating, being 
ANY of the following:
   (a) casserole dishes, with OR without lids;
   (b) frypans, with OR without lids;
   (c) saucepans, with OR without lids;
   (d) baking dishes, with OR without lids;
   (e) grill pans AND plates;
   (f) skillets;
   (g) woks, with OR without lids;
   (h) steamers, with OR without lids;
   (i) oven pans, with OR without lids;
   (j) baking pans, with OR without lids;
   (k) Dutch AND/OR French ovens, with OR without lids;
   (l) double boilers, with OR without lids;
   (m) griddle pans, with OR without lids

PANS, MUFFIN AND/OR CUPCAKE, carbon steel with a non stick 
coating

KITCHENWARE, being chrome plated wire baskets

UTENSILS, iron or steel, being ANY of the following:
   (a) baskets; 
   (b) bottle baskets; 
   (c) buckets; 
   (d) candle snuffers;
   (e) child safety gates; 
   (f) coal scuttles or hods; 
   (g) cotton bud dispenser boxes; 
   (h) dustbins; 
   (i) eye baths; 
   (j) flower boxes or planters;
   (k) hot water bottles; 
   (l) letter boxes;
   (m) luncheon boxes; 
   (n) movable boot scrapers; 
   (o) plant pots or hanging planters or plant tubs or plant 
       muck boxes or plant saucers;  
   (p) plant movers;
   (q) plate stands; 
   (r) rubbish bins;
   (s) shoe trees; 
   (t) flat irons stands; 
   (u) storage boxes or storage bins or storage tins; 
   (v) tissue paper holders or enclosures;
   (w) magazine holders; 
   (x) wash basins; 
   (y) watering cans; 
   (z) wine racks

EGG RINGS, carbon steel

KETTLES, STOVE TOP

PANS, MUFFIN AND/OR CUPCAKE, having multiple separated cups

KITCHENWARE, iron or steel, being ANY of the following:
   (a) bag dispensers;
   (b) bottles;
   (c) bowls;
   (d) bread bins;
   (e) canisters;
   (f) capacity measurers;
   (g) colanders;
   (h) cutlery or kitchen utensils stands and/or racks and/or 
trays;
   (i) dish drainers and/or dish drying racks;
   (j) milk cans;
   (k) double boilers and/or inserts;
   (l) fish kettles;
   (m) food or cake domes;
   (n) frying baskets;
   (o) funnels;
   (p) glass racks;
   (q) gridirons;
   (r) grilling racks;
   (s) hob guards;
   (t) wrapping holders and/or foil holders;
   (u) jelly or pastry moulds;
   (v) jugs;
   (w) kettles;
   (x) knife boxes or knife racks;
   (y) non electric coffee pots and/or percolators; 
   (z) paper towel holders;
  (aa) pasta inserts;
  (ab) plate racks or holders;
  (ac) preserving pans or jars;
  (ad) pressure cookers;
  (ae) rinsing baskets or strainers;
  (af) salad washers;
  (ag) pressure cooker separating compartments;
  (ah) shakers;
  (ai) sink cover plates;
  (aj) spice or condiments racks and/or stands;
  (ak) splatter screens or guards;
  (al) food bowl stands;
  (am) steamers and/or inserts;
  (an) storage tins and/or storage jars and/or storage caddies;
  (ao) sugar tins;
  (ap) suspension rails;
  (aq) tea infusers;
  (ar) trivets;
  (as) wine racks

UTENSILS, COOKING, iron or steel, being ANY of the following:
(a) double boilers and/or inserts;
(b) fish kettles;
(c) gridirons;
(d) grilling racks;
(e) non electric coffee pots and/or percolators;
(f) pasta inserts;
(g) pressure cookers;
(h) pressure cooker separating compartments;
(i) splatter screens and/or guards;
(j) steamers and/or inserts;
(k) trivets

KITCHENWARE, steel, being egg rings with handles

SINK ACCESSORIES, being ANY of the following:
  (a) colanders;
  (b) draining baskets;
  (c) drainers;
  (d) food preparation board and colander sets

FRAMES, GARDEN BED, steel, having ALL of the following:
  (a) length NOT greater than 1 100 mm;
  (b) width NOT greater than 780 mm;
  (c) depth NOT greater than 300 mm

PANS, paella, steel

HANGERS AND/OR SEPERATORS, steel, powder coated

HOUSEHOLD ARTICLES, in single OR double OR multiple 
format, being ANY of the following:
  (a) racks;
  (b) hooks;
  (c) loops;
  (d) holders;
  (e) bars

IRONING BOARDS

HOUSEHOLD ARTICLES, iron or steel, being EITHER of the following:
  (a) buckets;
  (b) hot water bottles

HOUSEHOLD ARTICLES, iron or steel, wall mounted, being EITHER of 
the following:
  (a) clothes iron holders; 
  (b) vacuum cleaner hose holders

GATES OR BARRIERS, SAFETY, with or without plastic fittings

SHOE ORGANISERS

BOARDS, IRONING, metal, incorporating an iron holder

BASKETS, PLANTER, having coconut fibre liners

SETS, CLEAN-UP, PET DROPPINGS, comprising pan and scraper

TABLEWARE, iron or steel, being ANY of the following:
   (a) baskets; 
   (b) bottles; 
   (c) bowls; 
   (d) card holders; 
   (e) cruets;
   (f) cups; 
   (g) decanters; 
   (h) dishes; 
   (i) drip stoppers; 
   (j) egg cups; 
   (k) fondues; 
   (l) food or cake domes; 
   (m) non electric food warmers; 
   (n) ice buckets; 
   (o) jugs; 
   (p) knife or chopstick rests;
   (q) mugs; 
   (r) mustard pots;
   (s) napkin and/or place card stands; 
   (t) non electric coffee pots or percolators; 
   (u) plates; 
   (v) plate stands; 
   (w) platters or serving plates; 
   (x) salad bowls; 
   (y) salt cellars; 
   (z) salt or pepper shakers; 
  (aa) sauce boats; 
  (ab) saucers; 
  (ac) serviette or napkin rings; 
  (ad) tea pot stands or cake stands; 
  (ae) sugar basins or shakers; 
  (af) table cloth clips; 
  (ag) table place mats or coasters; 
  (ah) sugar bowls and/or milk jugs and/or trays;
  (ai) tea infusers or tea honey sticks or tea dishes; 
  (aj) tea pots; 
  (ak) tea strainers; 
  (al) toast racks; 
  (am) trays; 
  (an) trivets; 
  (ao) tumblers; 
  (ap) tureens; 
  (aq) wine cooling buckets; 
  (ar) wine pouring cradles; 
  (as) wine bottle stands

WASH BASINS, HAND, stainless steel, complying with American 
Society for Testing and Materials standard ASTM A959 - 11, 
Type 304, having ALL of the following:
  (a) basin length 500 mm; 
  (b) basin width 420 mm;
  (c) basin depth 246 mm;
  (d) basin thickness 0.8 mm;
  (e) basin perimeter fascia 50 mm deep;
  (f) basin rear splash back 70 mm high
For the purposes of this Order, tolerances allowable for (a) to  
(f) are +/- 10%

SINKS, CLEANER'S, stainless steel, complying with American 
Society for Testing and Materials standard ASTM A959 - 11, 
Type 304, having ALL of the following:
  (a) sink length 555 mm; 
  (b) sink width 455 mm;
  (c) sink depth 260 mm;:
  (d) sink thickness 0.8 mm;
  (e) sink perimeter fascia 25 mm deep;
  (f) sink rear splash back 25 mm high;
  (g) hinged grate, having BOTH of the following:
        (i) horizontal rods, having a diameter of 12.7 mm;  
       (ii) vertical rods, having a diameter of 9.5 mm 
For the purposes of this Order, tolerances allowable for (a) to 
(g) are +/- 10%

DISPENSERS, continuous cloth towelling

SANITARY WARE, stainless steel, being ANY of the following:
   (a) bed pans;
   (b) commode pans;
   (c) urinals;
   (d) dressing jars;
   (e) catheter trays;
   (f) instrument trays/covers;
   (g) forceps jars;
   (h) thermometer jars;
   (i) pus basins;
   (j) emesis basins;
   (k) iodine cups;
   (l) cotton jars;
   (m) applicator jars;
   (n) oil cups;
   (o) ointment jars;
   (p) tampon mugs;
   (q) syringe sterilisers;
   (r) syringe cases;
   (s) finger sterilisers;
   (t) petri dishes;
   (u) soap dishes;
   (v) flasks;
   (w) mortars and pestles;
   (x) steriliser trays;
   (y) instrument cases;
   (z) dressing steriliser cases;
   (aa) portable sterilisers
   (ab) test tube racks

SHOWERS, HANDHELD AND OVERHEAD, including ALL of the following:
  (a) rail;
  (b) wall connectors;
  (c) hose;
  (d) diverter;
  (e) metal AND/OR plastic shower head;
  (f) rail slide holders

SHOWER HEADS, stainless steel

WASTE DISPOSAL UNITS, stainless steel, whether OR not 
incorporating soap dispensers AND/OR paper towel dispensers 
AND/OR mirrors

STRAINERS, BASKET, SINK OUTLET, with or without overflow 
connection

SANITARYWARE, iron or steel, being EITHER of the following:
  (a) shower organisers;
  (b) soap dishes or caddies

SANITARY WARE, iron or steel, being EITHER of the following:
  (a) toilet roll stands; 
  (b) toothbrush holders

SANITARY WARE, iron or steel, being ANY of the following:
  (a) bed pans;
  (b) chamber pots;
  (c) eye baths;
  (d) shower racks;
  (e) spittoons;
  (f) toilet brush holders;
  (g) toilet paper holders;
  (h) wash basins

COVERS AND/OR FRAMES AND/OR GRATES, grey cast iron, having clear 
opening dimensions NOT less than 300 mm NOT greater than 1 200 
mm

BALLS, dia NOT exceeding 20 mm

GRINDING BALLS, cast steel, having a diameter NOT less than
400 mm

CAST GRINDING MEDIA, CYLPEBS, diameter NOT greater than 20 mm

ARRESTERS, flame

INSULATION BARS, SINTER COOLER PALLET CAR, C shaped, cast steel

COVERS AND/OR FRAMES AND/OR GRATES, ductile iron, having clear 
opening dimensions NOT less than 300 mm NOT greater than 1 200 mm

SPACERS, CABLE BOLT, cast iron, having BOTH of the following:
  (a) length NOT GREATER THAN 18 mm;
  (b) external diameter NOT GREATER THAN 25 mm

PARTS, TWISTLOCK, being ANY of the following:
  (a) housings;
  (b) shafts and nuts;
  (c) emergency releases

ACCESS COVERS AND FRAMES, cast iron

BALLS, dia NOT exceeding 20 mm

BALLS, dia NOT exceeding 20 mm

PARTS, VERTICAL COMBUSTION CHAMBER, being ANY of the following:
  (a) ceramic anchors AND/OR anchor supports;
  (b) wedge support brackets;
  (c) ring brackets;  
  (d) ring bevels

RINGS, FORGED FLANGE, having a minimum outside diameter of
 2 720 mm

ROLL OR TYRE BODIES, GRINDING MACHINE, hot pressed forged steel, 
having BOTH of the following:
  (a)outside diameter NOT less than 2 000 mm;
  (b) weight NOT less than 27 t

RINGS, FORGED FLANGE, having a minimum outside diameter of
 2 720 mm

RINGS, stainless steel, fishing lure or trace, but NOT including
 round split rings, having an ID less than 11 mm, and oval split
 rings, having an OD less than 9 mm and a full length less than 20 mm

GABIONS/MATTRESSES, rectangular, of zinc coated mesh wire in sizes
 2 mm to 4 mm

WIRE, steel, high carbon, oil hardened and tempered, dia NOT
 exceeding 0.9 mm

WIRE, book binding, nylon coated, in preformed continuous loops
 on bulk reels, sizes 4.76 mm to 25.4 mm (3/16 in. to 1 in.)

STEEL WIRE FIBRES, deformed and cut, cold drawn with hooked ends,
 having ALL of the following:
   (a) conforming to ASTM A820 type 1;
   (b) length between 20 mm and 60 mm (+ or - 10%) for individual
       fibres;
   (c) diameter between 0.45 mm and 1.05 mm (+ or - 10%) for
       individual fibres;
   (d) minimum tensile strength of 1 000 MPa;
   (e) minimum aspect ratio (length/diameter) of 60;
   (f) manufactured from low carbon steel (< 0.095% carbon) in
       accordance with EN 10016-2-C9D

HANGERS, CALENDAR, plastic coated steel wire, having a semi-
 circular loop in the centre

WIRE, BRUSH, hardened and tempered, diameter 35 gauge (CWG) to
 diameter 28 gauge (GWG) BOTH inclusive, in lengths NOT exceeding
 76.2 mm (+ or - 5%).

GABIONS/MATTRESSES, being cubic or three dimensional rectangular,
 manufactured from polyvinyl chloride sheathed, zinc coated mesh wire
 of 2 mm to 4 mm

ENCLOSURES, ANIMAL, portable, coated wire, having a weight NOT 
greater than 5 kg

HOOKS, PLANT SUPPORT, with polypropylene string

STEEL WIRE FIBRES, cold drawn with deformed ends OR continuously 
deformed, complying with British Standards BS EN 14889-
1:2006 and BS EN 10016-2:1995, having ALL of the following:
  (a) fibre length NOT less than 43 mm and NOT greater than 
      60 mm;
  (b) fibre diameter NOT less than 0.85 mm and NOT greater than 
      1.00 mm;
  (c) tensile strength NOT less than 1 000 MPa;
  (d) minimum aspect ratio (length/diameter) of 50:1

WIRE KENNELS, DOG AND CAT, collapsible, having BOTH of the following
   (a) fluid capture moat;
   (b) length NOT greater than 130 cm

BASKETS, WASTE PAPER, wire mesh

LOAD LUGS, lifting, being swivelling threaded bolt, welded lug or
 eye bolt type, conforming to ISO Grade 8

BANDING, continuous, stainless steel, welded or prepared
 for welding, for conveyor and/or processing belts with ALL
 the following minimum mechanical properties:
   (a) 0.2% proof stress 980 MPa;
   (b) tensile stress 1 050 MPa;
   (c) hardness 320 hv 10

ARRESTERS, flame

TERMINALS, wire rope, swageless

SHACKLES, kenter

RINGS, nose, animal control

YACHT FITTINGS, stainless steel, rod rigging, being ANY of the
 following:
   (a) articulated spreader links;
   (b) stemball type spreader links;
   (c) stemballs;
   (d) coquilles;
   (e) rod to wire connectors

MANDRELS, sidepocket, being part of an oil pipe tubing string,
 shaped to house oilwell valves

CONNECTORS OR CONNECTING LINKS, chain, to Specifications DIN
 22252, 22253 or 22258 or equivalents, being parts for
 longwall mining system armoured face conveyors and stage loader
 conveyors, in ANY of the following chain sizes:
       Dia                                             Pitch
   (a) 18 mm                                            64 mm;
   (b) 22 mm                                            86 mm;
   (c) 26 mm                                            92 mm;
   (d) 30 mm                                           108 mm;
   (e) 34 mm                                           126 mm

RUPTURE (BURSTING) DISCS, pressure system, whether or not
 incorporating vacuum supports

THIMBLES, dressmakers" or tailors"

ELECTRODES, underwater

SUITS OF ARMOUR, full scale, being reproductions of medieval
 protective apparel

SWIVELS, chain, drop forged mild steel, but NOT including swivels
 fitted with thrust roller-bearings

BOBBINS, sewing machine

FITTINGS, tank or storage drum pressure relief, being ANY of the
 following:
   (a) drum vent adaptors;
   (b) drum vents;
   (c) flame arrester rodding and sampling units;
   (d) flame arrester vents;
   (e) flame arresters;
   (f) flash arrester fill units;
   (g) gauge hatches;
   (h) loading and unloading units

SPIKES, tree climbing

SLEEVES, swaging, wire rope or wire cable

GLOVES, chainmail

FITTINGS, hook type, key wallet

CLOTHING, safety, metal mesh

CLAMPS, exhaust, stainless steel, "V" band, having a dia of 76 mm
 or greater but NOT exceeding 153 mm

CABLE TIES, stainless steel self lock, length NOT exceeding 72 cm

PARTS, PASSENGER MOTOR VEHICLE, manufactured at least 30 years
 before the goods are entered for home consumption, or reproductions
 of these parts, being ANY of the following:
  (a) ferrules;
  (b) clips;
  (c) clamps;
  (d) locating pins;
  (e) buffers;
  (f) buffer pads mounting;
  (g) plugs;
  (h) sleeves;
  (i) stoneguards;
  (j) expanders;
  (k) non mechanical ventilators;
  (l) stays;
  (m) electric wiring brackets
  (n) pegs;
  (o) posts;
  (p) turnbuckles;
  (q) tubing and piping hangers;
  (r) road studs;
  (s) forged hooks;
  (t) glove boxes

PARTS, HYDRAULIC PIPE OR TUBE RIGID MOUNTING, being EITHER of the
 following:
   (a) plates;
   (b) rails

CONNECTORS, CONVEYOR CHAIN, having BOTH of the following:
   (a) diameter range 45 mm to 50 mm;
   (b) pitch range 140 mm to 150 mm

DISPENSERS, SOLDER ROLL, metal, non slip base

WEAR SLEEVE, SHAFT, consisting of ALL of the following:
   (a) stainless steel sleeve having a wall thickness less than
       0.3 mm, and an outside diameter surface having:
         (i) no machine lead;
        (ii) finish of 10 - 30 micro inches Ra;
   (b) installation tool

YACHT FITTINGS, ROD RIGGING, STAINLESS STEEL, being ANY of the
 following:
   (a) stemballs;
   (b) stemball seats;
   (c) stemball tangs;
   (d) screw in tangs;
   (e) rod balls;
   (f) spreader bends;
   (g) tip cups

CABLE PROTECTORS

MANDRELS, LOCKING, SUB SURFACE FLOW CONTROL

TOOL CHESTS, having six to twelve drawers, ball bearing OR
 frictional slides, fitted with handles

CONNECTORS, CONVEYOR CHAIN, complying with standard DIN 22252, 22253
 OR 22258, in EITHER of the following chain sizes:
        DIAMETER         PITCH
        42 mm            146 mm
        48 mm            152 mm

CASING HANGER SLIP AND SEAL, API specification 6A

CHAIN FITTINGS, Grade 80, being ANY of the following:
   (a) clevis shortening clutches, fitted with pin and retainer,
       sizes NOT less than 7 mm;
   (b) double ended H pattern chain connectors, sizes NOT less
       than 7 mm;
   (c) double ended H pattern chain couplers, sizes NOT
       less than 7 mm;
   (d) D pattern shackles, sizes NOT less than 7 mm;
   (e) hooks, being ANY of the following:
            (i) cargo, sizes NOT less than 7 mm;
           (ii) choker, sizes NOT less than 17 mm;
          (iii) cradle grab, sizes NOT less than 15 mm;
           (iv) foundry, sizes NOT less than 7 mm;
            (v) clevis grab, fitted with pin and retainer,
                sizes NOT less than 15 mm;
           (vi) swivel safety, sizes NOT less than 6 mm;
          (vii) self locking, sizes NOT less than 5.6 mm;
         (viii) shortening, with work load limit capability of 100%
                of each chain, size NOT less than 7 mm;
           (ix) eye sling, sizes NOT less than 16 mm;
            (x) clevis sling fitted with pin and retainer

HOOKS, WELD-ON, grade 80, with safety snap toggle

LINKS, clevis lug

SANDERS, with extension pole threaded adaptor

CHAIN FITTINGS, grade 80 (ISO Grade T) being ANY of the following:
   (a) clevis type shortening clutches, fitted with pin and
       retainer;
   (b) double ended H pattern connectors;
   (c) double ended H pattern coupling shackles;
   (d) D pattern shackles;
   (e) oblong master links in sizes NOT less than 26 mm diameter;
   (f) diamond master links with pin coupling and safety latch in
       sizes of 13 mm or 16 mm diameter;
   (g) suspension shackles with pin coupling and forged safety pin of
        13 mm diameter;
   (h) links, bow shaped, connecting and coupling;
   (i) hooks, being ANY of the following:
            (i) cargo;
           (ii) chocker;
          (iii) cradle grab;
           (iv) foundry;
            (v) shortening grab;
           (vi) swivel safety;
          (vii) self locking;
         (viii) sling;
           (ix) "C" pattern;
            (x) excavator;
           (xi) shortening

SHACKLES, "D", ANCHOR OR CHAIN, having an oval pin

CONTAINERS, TRANSPORT, having ALL of the following:
   (a) four tiers;
   (b) rounded corner columns of steel;
   (c) tine pockets;
   (d) discharge doors

SLEEVES, SLIDING, OIL AND GAS WELL, having ALL of the following:
   (a) inner sleeve that can be opened and closed;
   (b) nipple profile;
   (c) bottom polished sealing area;
   (d) top packoff sealing area

CONNECTING LINKS, grade 80, comprising a pin and two identical body
 halves capable of being separated

SHANK ADAPTORS AND DRILL ROD COUPLINGS, ROCK DRILLING

PARTS, CENTRALIZER OR STOP RING, being ANY of the following:
  (a) bows;
  (b) end bands;
  (c) spiral locking pins

CABLE TIES, stainless steel

KEY RINGS, fitted with novelty figurines or badges made of
 polyvinyl chloride

FASTENERS, CONVEYOR BELT

CONNECTORS, CHAIN, alloy steel (CrNiMo) construction, in ANY of the
 following chain sizes:
   Diameter          Pitch          Tolerance
    30 mm             108 mm          +/- 1.1 mm
    34 mm             126 mm          +/- 1.3 mm
    38 mm             137 mm          +/- 1.4 mm
    42 mm             152 mm          +/- 1.5 mm

TURNBUCKLES, having a thread diameter of ANY of the following sizes:
   (a) 4 mm;
   (b) 5 mm;
   (c) 6 mm;
   (d) 8 mm

SHACKLES, having a safe working load of 4 t or greater

HOOKS, being ANY of the following:
   (a) clevis grab hooks;
   (b) slip hooks;
   (c) eye grab hooks;
   (d) eye slip hooks;
   (e) claw hooks

SHACKLES, screw pin or round pin type, sizes 5 mm to 32 mm

THIMBLES, wire rope, in EITHER of the following types and sizes:
   (a) stainless steel NOT greater than 9 mm;
   (b) steel NOT greater than 20 mm

CENTRALIZERS OR STOP RINGS, casing and tubing

CONNECTORS OR CONNECTING LINKS, chain, to specifications
 DIN 22252, 22253, or 22258 or equivalents, being parts for longwall
 mining system armoured face conveyors and stage loader conveyors,
 in chain size 38 mm dia, 137 mm pitch

BUCKLES, stainless steel, to specification AISI 201 or 316
 "NOTE:  Because of the Tariff change on 1 July 1993, the tariff
  classification applicable to the goods described is 7326.90.00
  from the Operative Date to 30 June 1993."

PARTS, UNDERWATER THRUSTER TURNING TOOL, being upper beams

BRACING STRAP TENSIONERS, including ALL of the following:
  (a) hex self-drilling pilot point bolt;
  (b) tensioner bracket;
  (c) convex flanged washer;
  (d) threaded nut with bracket

SETS, HOSE CLAMP, including ALL of the following:
  (a) clamps;
  (b) screwdriver;
  (c) wall mounting brackets

PARTS, FORKLIFT, being ANY of the following:
  (a) spreader twistlock;
  (b) twistlock arm;
  (c) twistlock pin kit

CARRIER TUBE, PERFORATING GUN, with OR without loading tube 
AND/OR thread protector

TRANSPORTATION FRAMES, DISTRIBUTED BUOYANCY MODULE

UPLIFT PREVENTERS, SUBSEA OIL AND/OR GAS WELL

ROLL THIMBLES, SUBSEA OIL AND GAS

PULL-IN HEADS, SUBSEA CABLES

INSTALLATION OR RETRIEVAL PLUGS, SUBSEA SUCTION ANCHOR, with 
handle

TRAYS, LIVE CHICKEN HANDLING SYSTEM, having stainless steel 
frames AND plastic panels

DEPLOYMENT FRAMES, including BOTH of the following: 
  (a) steel cable drum with an outer diameter NOT greater than 
5 m;
  (b) steel skid including forklift slots, with a height NOT 
greater than 4.5 m AND a width NOT greater than 3 m

TETHERS, COIL, polyurethane coated steel, having ALL of the 
following:
  (a) carabiners AND/OR clips;
  (b) maximum load capacity NOT greater than 2.3 kg;
  (c) length NOT greater than 1 700 mm

TRAY DIVIDERS, BROILER HANDLING, having ALL of the following:
  (a) plates;
  (b) tendons;
  (c) spacers;
  (d) brackets

POSITIONING BANDS, steel, including ALL of the following:
  (a) closing block;
  (b) silver steel pin;
  (c) screws;
  (d) disc spring;
  (e) deformation washer;
  (f) spring support

PROTECTION FRAMES, SUBSEA CHIMNEY

RETORT TRAYS, FOOD POUCH STERILISATION, stainless steel, 
stackable, having ALL of the following: 
  (a) width NOT greater than 1 031 mm; 
  (b) length NOT greater than 906 mm; 
  (c) height NOT greater than 104 mm; 
  (d) NOT less than 16 internal pockets and NOT greater than 30 
      internal pockets

PARTS, MOORING CHAIN CONNECTORS, being ANY of the following:  
  (a) shackles;
  (b) plates;
  (c) links;
  (d) sockets;
  (e) hangers;
  (f) nodes;
  (g) pin locks;
  (h) thimbles;
  (i) swivels

MUDMAT AND UPSTAND ASSEMBLIES, SUBSEA, including ALL of the 
following:
  (a) padeyes;
  (b) anchor bolts;
  (c) polyester sling's

TETHER CLAMPS, SUBSEA FLEXIBLE RISER, steel

MUDMATS, SUBSEA, steel, with OR without hinges AND/OR piles, 
including ALL of the following: 
  (a) plates;
  (b) pipes; 
  (c) weld-on pivot links;
  (d) lift points

GROUT PACKERS, steel body with expanding rubber collar

CLIPS, metal, with plastic strap incorporating a press stud

SEALS, OIL AND/OR GAS WELLHEAD, having BOTH of the following:
  (a) internal working pressure NOT greater than 1 210 bar;
  (b) external working pressure NOT greater than 105 bar

SHAFT BRUSH SEALS AND/OR GRATE CHAIN SIDEPLATE SEAL ASSEMBLIES, 
TRAVELLING GRATE

FOAM POURERS, with OR without clamps, having ALL the following:
  (a) width NOT greater than 1 050 mm;
  (b) height NOT greater than 710 mm;
  (c) stainless steel mesh insert

PROTECTION CLAMPS, SUBSEA, being ANY of the following:
  (a) top clamp;
  (b) top clamp with anodes;
  (c) bottom clamp

SHIMS AND/OR WELDMENTS, PIPE PROTECTION, OIL AND/OR GAS WELL

PUSH RODS, MARINE LOADING ARM, including both helical spring AND 
linkage arm

SPOOL FABRICATION JIGS, steel

TEST STANDS, SUBSEA CONTROL MODULE, including ALL of following:
  (a) valves;
  (b) dump line hoses with test connectors AND adapter;
  (c) junction boxes

DEAD END GRIPS, with OR without ANY of the following:
  (a) u-bolt;
  (b) housing;
  (c) wedges;
  (d) spacer bar;
  (e) nuts AND washers;
  (f) retaining rods;
  (g) colour coded tags

FITTINGS, LIFTING AND/OR LASHING CHAIN, steel, being ANY of the 
following:
  (a) master links;
  (b) master link assemblies including transition links;
  (c) transition links;
  (d) connecting links;
  (e) clevis master sets;
  (f) lifting points;
  (g) shackles;
  (h) hooks

BELTING, PARTICLE BOARD AND/OR MEDOUM DENSITY FIBRE BOARD 
PRESS, steel, having BOTH of the following:
  (a) width NOT less than 2,600 mm;
  (b) thickness NOT less than 2.5 mm

MIXERS, TAIL GAS, static, including BOTH of the following:
  (a) nozzles;
  (b) lifting lugs

SEALS, TEST, SUBSEA

COMPLETION TOOLS, SUBSEA DRILLING, being ANY of the following:
  (a) bore protectors;
  (b) wear sleeves;
  (c) wear bushings

BEND RESTRICTORS, SUBSEA, whether OR not assembled

BORE PROTECTORS, SUBSEA,

SKIRTINGS, CONVEYOR, including BOTH of the following:
  (a) polyurethane carrier;
  (b) steel blades

COMPONENTS, FEED MILL BIN, being ANY of the following:
  (a) twin skin wall panels;
  (b) column plates OR flange plates;
  (c) hoppers;
  (d) chutes plates OR slanting plates;
  (e) cover plates with manhole

STABS OR PLATES OR DIAMOULDS, PARKING, SUBSEA with OR without 
one OR more of the following:
  (a) caps;
  (b) protective cover;
  (c) remotely operated vehicle handle;
  (d) guide pins;
  (e) seals

EXPLOSION VENTS, COMBUSTIBLE DUST, having a feeding chute, with 
OR without EITHER of the following:
  (a) rupture disc;
  (b) sensor

RETORT TRAYS, FOOD POUCH STERILISATION, stainless steel, 
stackable, having ALL of the following:
  (a) width NOT greater than 1 265 mm;
  (b) length NOT greater than 1 345 mm;
  (c) height NOT greater than 62 mm;
  (d) perforated areas;
  (e) NOT less than 47 internal pockets,
with OR without handles

CONTAINERS, CASE ORDER MACHINE, STORAGE AND RETRIEVAL SYSTEM, 
having a maximum weight per load NOT less than 
1 500 kilograms

PLUGS, SUBSEA OIL AND/OR GAS WELL, having keys AND/OR mandrels

CLIPS, SOLAR PHOTOVOLTAIC ARRAY, stainless steel, being ANY of 
the following:
  (a) two-cable straight clips;
  (b) four-cable straight clips;
  (c) two-cable 90 degree AND/OR 180 degree clips;
  (d) four-cable 90 degree clips

PALLETS, MOULD TRANSPORTER, having ALL of the following:
  (a) four OR more legs;
  (b) width NOT less than 2 metres and NOT greater than 3 metres;
  (c) length NOT less than 2.4 metres and NOT greater than
      3 metres;
  (d) payload NOT greater than 50 000 kg

STAB PLATE PROTECTIVE COVERS, SUBSEA CHRISTMAS TREE AND/OR 
MANIFOLD

SPACER GUNS, DOWNHOLE WELL, including ALL of the following:
  (a) perforated shroud;
  (b) chemical reagents;
  (c) rings

WIRELINE PLUGS, SUBSEA, OIL AND/OR GAS WELL

CONNECTORS, SOCKETS AND/OR DOWELS, CONCRETE TUNNEL SEGMENT

TAPPING LID, discharge AND transport crucible, having ALL of the 
following:
  (a) internal diameter NOT less than 1 725 mm;
  (b) forklift pocket;
  (c) crane hook

LANDING CENTRALISERS, OIL AND/OR GAS WELL

BELTS, alloy duplex stainless steel, cold rolled, with OR 
without v-ropes, having rounded edges

ROADSIDE SAFETY BARRIERS, modular, portable, having BOTH of the 
following:
  (a) profiles length NOT greater than 12 m; 
  (b) anchor shoes;
with OR without ANY of the following:
      (i) anchor pins;
     (ii) threaded rods

STEEL SLEEVES, SETTING TOOL, tapered, having ALL of the 
following:
  (a) height NOT less than 850 mm and NOT greater than 900 mm;
  (b) diameter NOT less than 70 mm and NOT greater than 90 mm;
  (c) plastic end cap

GUIDE RAILS, STEEL, floor mountable, having ALL of the following;
  a) head width 55.00 mm;
  b) head height 65.00 mm;
  c) bottom width 150.00 mm;
  d) length 9000.00 mm AND/OR 540.00 mm;
  e) anchors AND/OR chemical anchors; 
  f) clamps;
  g) clamp fasteners;
  h) mounting plates;
  i) mounting bolts and washers and nuts
For the purpose of this Order, tolerances allowable for 
specifications (a), (b), (c) and (d) is +/- 5%

CURING FRAMES, UNCURED CONCRETE PANEL, having ALL of the 
following:
  (a) stacking pins;
  (b) connection hooks;
  (c) carbon steel construction

SILENCER PANELS, POWER STATION, including ALL of the following:
  (a) silencers, including BOTH of the following:
         (i) chambers having basalt wool filling;
        (ii) steel sheeting AND/OR casing,
  (b) brackets;
  (c) emission sound power level NOT greater than 100 dB (A)

BACKREST, TOILET, having ALL of the following:
  (a) stainless steel arms;
  (b) stainless steel body plate;
  (c) plastic resting pad

BATH SUPPORT FRAMES, including ALL of the following:
  (a) bath frames;
  (b) adjustable feet;
  (c) nuts AND washers;
  (d) silicone sealant;
  (e) adhesive tape

TRACKS, metal, all terrain, over tyre type, with OR without 
track locks AND/OR mounting tool

TUBING AND/OR PIPING, liquid circulation, including BOTH of the 
following:
  (a) stainless steel pipes AND/OR tubes;
  (b) nozzles

VAPOUR CIRCULATION AND TREATMENT LINE, CRYSTALLINE LITHIUM 
PRODUCTION, including BOTH of the following:
  (a) stainless steel pipes AND/OR tubes;
  (b) nozzles

RACK AND ENCLOSURE FITTINGS, including ANY of the following:
  (a) horizontal AND vertical cable mounts;
  (b) vertical fibre mounts;
  (c) hinged covers;
  (d) side channels

CLAMPS, RAILWAY TRACK DAMPING BLOCK, stainless steel

MOUNTINGS, RAILWAY NOISE DAMPING PANELS AND/OR WALLS, with OR 
without mounting hardware

PIPE MOUNTING COMPONENTS, being ANY of the 
following:
  (a) slide sets;
  (b) blocksets;
  (c) mounting kits consisting of ALL of the following:
         (i) threaded stud;
        (ii) hexagon nut;
       (iii) rod coupling;
        (iv) universal joints,
  (d) universal joints;
  (e) toggle stud

EXPLOSION VENTS, having ANY of the following:
  (a) gaskets;
  (b) flameless vents with ceramic filters;
  (c) insulation;
  (d) sensors

PALLET INLOADERS, with OR without ANY of the following:
  (a) stabiliser with OR without braces;
  (b) safety pins;
  (c) stanchions AND/OR struts;
  (d) supports, metal AND/OR wood AND/OR rubber;
  (e) document compartment

FLUE GAS DUCTS, RECUPERATOR, GAS RECOVERY SYSTEM, including ALL 
of the following:
  (a) modules;
  (b) flanges;
  (c) adapters;
  (d) plates;
  (e) shims;
  (f) compensator

PANELS, insulated, including ALL of the following:
  (a) polyisocyanurate foam inner core with steel sheeting on 
      both sides; 
  (b) length NOT less than 11 500 mm; 
  (c) width being ONE or MORE of the following sizes:
           (i) 538 mm; 
          (ii) 567 mm; 
         (iii) 575 mm; 
          (iv) 610 mm 
For the purpose of this order a tolerance of +10% or -10% is 
allowable for (c)

PANELS, hexagonal cells, stainless steel

RAINWATER DRAINAGE OUTLETS, siphonic, with OR without anti-
vortex plate, with OR without overflow device, having BOTH of 
the following;
  (a) flow rate NOT greater than 65 l/s;
  (b) gutter OR bitumen water proofing adapter plates

DISCHARGE HOPPERS, GERMINATING VESSEL, MALTING PLANT

INLET AND OUTLET DUCT CONNECTORS, GERMINATING AND/OR KILNING 
VESSEL

SHUTTERING EXTENSIONS, PRE-CAST CONCRETE AUTOMATION PLANT, 
having screw mountable adapters with chamfer strip

DAMPENERS, SUBSEA AND/OR DOWNHOLE, acoustic, non-mechanical, 
whether OR not assembled

CLAMPS, REPEATER, DOWNHOLE TUBING, stainless steel, whether OR 
not assembled, with OR without sealed nut AND/OR transport case, 
including BOTH of the following:
  (a) working pressure rating NOT less than 1 200 bar;
  (b) maximum working temperature rating NOT less than 160 
      degrees Celsius and NOT greater than 170 degrees Celsius

LATCHES, lever operated, galvanized steel

FITTINGS, WALL PANEL, being ANY of the following:
  (a) fixing connector mechanism, horizontal tube to vertical
      tube;
  (b) tube spacers with OR without brackets;
  (c) anti-vibration clips;
  (d) angle corner reinforcement brackets;
  (e) connectors, tube to sanitary fitting;
  (f) floor AND wall brackets;
  (g) plates

BOLTS, EXPANSION, being folded tube with welded end bushings

FITTINGS, SAFETY HARNESS, stainless steel, being ANY of the 
following:
  (a) tensioners;
  (b) brackets;
  (c) anchors;
  (d) fixing plates;
  (e) base plates;
  (f) shuttles;
  (g) toggles;
  (h) joiners; 
  (i) energy absorbing connectors; 
  (j) variable height AND distance brackets;
  (k) buckles;
  (l) connection adjusters;
  (m) O-rings; 
  (n) spigots

FITTINGS, SAFETY HARNESS, steel, being ANY of the following:
  (a) connection adaptors;
  (b) O-rings;
  (c) quick release rings

CLIPS, FASTENING AND GROUNDING, SOLAR PANEL, screwless

WALL AND/OR POLE MOUNTING KITS, FIBRE OPTIC CABLE CLOSURE, 
having ALL of the following:
  (a) brackets AND/OR plates AND/OR holders;
  (b) clamping bands;
  (c) cable ties;
  (d) screws AND/OR plugs

PIPES, SHUNTED SCREEN, OIL AND/OR GAS WELL GRAVEL PACK, with OR 
without protective sleeves, including BOTH of the following:
  (a) base pipe;
  (b) tubes

FENDER PANELS AND/OR FRAMES, MARINE WHARF, having two OR more of 
the following:
  (a) pads;
  (b) chains;
  (c) brackets AND/OR cleats;
  (d) bolts AND/OR nuts AND/OR washers;
  (e) grommets;
  (f) spools

BRACKETS, CAR HEADREST, COMPUTER TABLET HOLDER

MOUNTING BRACKETS, POWER POINT, stud wall

CABLE BOLT TENSIONERS, having ALL of the following:
  (a) dome;
  (b) barrel;
  (c) socket;
  (d) pre-tension capacity NOT greater than ten tonnes

CLOSURES, PRESSURE VESSEL, having pressure locking mechanisms

PARTS, INTERMEDIATE BULK CONTAINER, galvanized steel, pressed 
AND/OR formed AND/OR pre-drilled, being ANY of the following:
  (a) bottom plates;
  (b) middle OR corner feet;
  (c) centre bridges;
  (d) label affixing plates;
  (e) horizontal AND vertical structural support bars

MANDRELS, DOWNHOLE, OIL AND/OR GAS WELL, alloy steel, having ALL 
of the following:
  (a) side connector port;
  (b) upper AND lower threaded connectors;
  (c) maximum working pressure rating NOT less than 650 bar

AIR VENTS, iron AND/OR steel, having swirl air diffusing slats

CABLE CLEATS, stainless steel, including ALL of the following:
  (a) polymeric liner;
  (b) single OR trefoil OR quad OR bundled retention;
  (c) conforming to International Electrotechnical  
      Commission Standard 61914:2009 (IEC 61914:2009)

LOAD LUGS, LIFTING, being swivel eye bolts OR swivel lifting 
points, whether OR not incorporating a ball bearing

ADAPTER SPOOLS, SUBSEA, BLOWOUT PREVENTER STACK

COMPONENTS, INTERMEDIATE BULK CONTAINER, galvanised steel, being 
ANY of the following:
  (a) label plates; 
  (b) pallet base perimeter bars;
  (c) cross re-enforcement plates;
  (d) diagonal top bars;
  (e) pallet pans;
  (f) container re-enforcement bars, having a thickness of 0.8 mm
      AND a length of 4.25 m
For the purposes of this Order, tolerances allowable for 
specification (f) are +/- 10%

DEPLOYMENT BASKETS, UMBILICAL, SUBSEA

TEST STUMPS, BLOW OUT PREVENTER, OIL AND/OR GAS WELL

FASTENING DISCS, GRATING, stainless steel

PARTS, OVERHEAD ELECTRIC WIRE SYSTEM, being stainless steel 
forked collar socket connectors

WEAR SLEEVES, carbon steel OR stainless steel, having a sleeve 
thickness NOT less than 0.28 mm and NOT greater than 2.40 mm

COUPLINGS, TRAM, being tow bars including spherical bearings

CLAMPS, being ANY of the following:
  (a) bolt;
  (b) hose;
  (c) double ear;
  (d) worm gear;
  (e) claw

SETS, GUIDE RAIL CONNECTOR, CIRCULAR SAW, including ALL of the 
following: 
  (a) main metal strips;
  (b) support metal strips;
  (c) screws;
  (d) hex key

QUICK CONNECT ASSEMBLIES, SUBSEA AND/OR SURFACE, OIL AND/OR GAS 
WELL, whether OR not assembled, having BOTH of the following:
  (a) upper connector;
  (b) lower connector

ANCHORS, TIMBER POST, galvanised steel

SHELVING ASSEMBLIES, including BOTH of the following:
  (a) wire mesh, having a wire thickness NOT less than 4 mm;
  (b) clips

OFFSET CENTRALISERS, OIL AND/OR GAS WELL EQUIPMENT

PARTS, POST TENSIONING ANCHORAGE SYSTEM, steel, being ANY of the 
following:
  (a) anchorages, including ALL of the following:
         (i) wedges;
        (ii) wedge plates;
       (iii) anchor bodies, 
  (b) anchor bodies;
  (c) wedge plates; 
  (d) wedges;
  (e) couplers

CABLE AND CONTROL LINE PROTECTORS, DOWNHOLE

MANDRELS, PRESSURE AND TEMPERATURE GAUGE PROTECTOR, OIL AND GAS 
WELL, steel

STANDS, MITRE SAW, metal, with OR without stand side length 
extensions, having a weight load carrying capacity NOT greater 
than 200 kg

TIN BOXES, CIGARETTES AND/OR TOBACCO PRODUCTS

PIPE CLAMPS, rubber lined, having NOT more than two screws

RACKS, STORAGE, COMPACT DISC

FRAMES AND/OR STAY PLATES, TRANSIT ASSEMBLY, multi-cable AND/OR 
multi-pipe AND/OR multi-conduit

MANDRELS, POCKET, OIL AND GAS WELL

SHELF MANAGEMENT SYSTEM, PRODUCT MOVER, having ALL of the 
following:
  (a) fixing brackets;
  (b) front riser;
  (c) dividers;
  (d) rollers

AIR VENTS, iron AND/OR steel, interior wall mounted, including 
BOTH of the following:
  (a) manually operated opening louvres;
  (b) decorative grills

LADDERS, PONTOON, stainless steel, telescopic

STEERING WHEELS, BOAT, stainless steel

ANCHORS, MARINE FENDER

PANELS, FENDER, MARINE WHARF

HANGERS, PICTURE, consisting of BOTH of the following:
  (a) hanger;
  (b) nail

DEVICES, HANDLING AND/OR LIFTING AND/OR TESTING, OIL AND GAS 
WELL, being EITHER the following:
  (a) testing and/or handling and/or lifting tools;
  (c) caps and/or hubs

WELLHEAD HOUSINGS, SUBSEA, with extension joint

DEVICES, HANDLING AND/OR LIFTING, SUBSEA TREE, OIL AND GAS WELL

LINKS, METALLIC CARTRIDGE BELT

CLAMPS, TUBING OR CABLE OR LINE SUPPORT, BY PASS SYSTEM, OIL AND 
GAS WELL

ENCLOSURES, PROTECTION, stainless steel, being EITHER of 
the following:
  (a) terminal boxes;
  (b) command panels with support arms

LOADING FRAMES, STEEL PLATE

BANDING, CONVEYOR AND/OR PROCESSING LINES, steel, continuous, 
welded or prepared for welding, being ANY of the following:
  (a) mill finished; 
  (b) ground;
  (c) polished

FITTINGS, ROOF DRAINAGE, steel, being ANY of the 
following:
  (a) European bead gutter connectors;
  (b) European bead gutter hooks;
  (c) European bead fascia hangers;
  (d) external corners;
  (e) internal corners;
  (f) stop ends;
  (g) gutter sieves;
  (h) pipe covers;
  (i) European bead pipe brackets;
  (j) European bead wall holders;
  (k) guttering
including sets of 2 or more of the above

BED GUARDS, CHILD SAFETY

STANDS, FLAT SCREEN DISPLAY, freestanding or desk mounted

STANDS, MITRE SAW, having BOTH of the following:
  (a) adjustable support rollers;
  (b) weight load capacity NOT less than 200 kg

HOLDERS OR HANGERS, CHAIR

ADAPTORS, CHANNEL, RAIL

CLAMPS, LEVER LOCKING, steel, having a closing force NOT less 
than 25 N.m

CASINGS, JUNCTION BOXES, steel AND/OR cast iron

EXTENSIONS, GUIDE POST, SUBSEA, OIL AND GAS WELL

HANDLES, BROOM, tubular steel, having a diameter NOT greater 
than 40 mm,

BELTS, CONVEYOR, SPIRAL, having BOTH of the following:
  (a) stainless steel links;
  (b) contractible edges, left or right hand curvature

AXLES, BIN, having ALL of the following:
  (a) length NOT less than 380 mm and NOT greater than 555 mm;
  (b) diameter NOT less than 20 mm and NOT greater than 24 mm;
  (c) zinc electroplating

PANELS, CABLE MANAGEMENT

KEYRINGS, personalised, incorporating a textile strap

FITTINGS, REFRACTORY, being ANY of the following:
  (a) retaining rings;
  (b) anchors;
  (c) taps;
  (d) claws

FITTINGS, YACHT, stainless steel, being ANY of the following:
  (a) folding eye pads;
  (b) babystay adjustors

PLUGS, SHOULDER, HEADER BOX

ANCHOR POINTS, steel, safety

PARTS, CHAIN, being latch hooks

FERRULES, WIRE ROPE

CHAIN FITTINGS, being ANY of the following:
  (a) hooks, grade 70, grade 80, grade 100 or grade 120;
  (b) chain connectors, NOT including oblong master links;
  (c) chain and sling connectors;
  (d) clevis master links;
  (e) rotating transport links;
  (f) quick links

FITTINGS, FALL PROTECTION, being ANY of the following:
  (a) rope grabs;
  (b) adjusters;
  (c) hooks;
  (d) karabiners;
  (e) connectors;
  (f) ascenders;
  (g) descenders;
  (h) tensioners

FLANGES, DRUM, STEEL

GRIPS OR CLIPS, WIRE ROPE

THIMBLES, WIRE ROPE

TINS, novelty, with or without a mechanical locking device,
 having ANY of the following:
   (a) hinged lid;
   (b) decorated surface;
   (c) non-detachable handle;
   (d) zipper closing;
   (e) less than 125 grams of confectionary

WORK BENCH, incorporating a vice

REFRIGERANT RECEIVER, AIR CONDITIONING, having a fixed vane outlet

TINS, NOVELTY, with or without a mechanical locking device,
 having ANY of the following:
   (a) hinged lid;
   (b) decorated surface;
   (c) non detachable handle

PINS, HINGE, CONVEYOR BELT, having a length greater than 40 cm

RACKS, STORAGE, COMPACT DISC