Tariff Concession Orders

ARTICLES, CERAMIC, acid resistant, being ANY of the following:
   (a) tiles;
   (b) bricks, including grid, skew, carbon and insulation bricks;
   (c) sleeves;
   (d) saddles;
   (e) cross-partition rings;
   (f) grid scaffolding

INSULATING BRICK, based on siliceous fossil meals having ALL of the
 following characteristics:
   (a) a dry bulk density NOT greater than 600 kg/cu m;
   (b) a silica content between 70 and 80%;
   (c) a thermal conductivity of less than 0.2 W/mk when measured at
       or below 600 degrees C

BLANKETS OR PADS, INSULATION

MAGNESIA ALUMINA SPINEL KILN REFRACTORY BRICKS, double sintered,
 shape standards VDZ and ISO sizing standards B322, B422, B622 and
 B822, comprising ALL of the following:
   (a) magnesium oxide (Mg0) NOT less than 80.0% (by weight);
   (b) calcium oxide (Ca) NOT greater than 1.4%;
   (c) ferrous oxide (Fe203) NOT greater than 8.2%;
   (d) silicon dioxide (SiO2) NOT greater than 1.3%;
   (e) zirconian oxide (ZrO2) NOT greater than 1.8%;
   (f) carbon (C) NOT greater than 0.5%;
   (g) aluminium trioxide (Al2O3) NOT less than 3% and NOT greater
       14.5%;
   (h) bulk density NOT less than 2.8 g/cu cm;
   (i) cold crushing strength NOT less than 50 MPa

REFRACTORY BRICKS, having a combined magnesia oxide (MgO) AND 
chromite oxide(Cr2O3) content of NOT less than 50%

TAP-HOLES, having a basis of magnesium oxide

REFRACTORY BRICKS, having ALL of the following:
  (a) magnesia (Mg0) content NOT less than 38%;
  (b) calcium oxide (Ca0) content NOT less than 40%;
  (c) silica (Si02) content NOT greater than 5%;
  (d) bulk density NOT less than 2g/cc

REFRACTORY BRICKS AND SHAPES, STEEL MAKING VACUUM DEGASSER, based
 on magnesia and chrome, fired, having ALL of the following:
   (a) magnesia (MgO) content 55% OR greater;
   (b) chromium oxide (Cr203) content 18% OR greater;
   (c) silica (Si02) content 1.7% OR less;
   (d) bulk density 3.15 grams per cubic centimetre OR greater;
   (e) apparent porosity 17% OR less;
   (f) cold crushing strength 40 newton/square millimetre (N/mm2)
       OR greater

REFRACTORY BRICKS AND SHAPES, having ALL of the following:
  (a) magnesia (Mg0) content NOT less than 48%;
  (b) chromic oxide (Cr203) content NOT less than 15%;
  (c) silica (Si02) content NOT greater than 3%

BRICKS AND/OR SHAPES, REFRACTORY, having ALL of the following:
  (a) magnesia (Mg0) content NOT less than 55%;
  (b) chromic oxide (Cr203) content NOT less than 15%;
  (c) silica (Si02) content NOT greater than 3%

REFRACTORY BRICKS, magnesia

MAGNESIA ALUMINA SPINEL KILN REFRACTORY BRICKS, double sintered,
 shape standards VDZ and ISO sizing standards B322, B422, B622 and
 B822, comprising ALL of the following:
   (a) magnesium oxide (Mg0) NOT less than 80.0% (by weight);
   (b) calcium oxide (Ca) NOT greater than 1.4%;
   (c) ferrous oxide (Fe203) NOT greater than 8.2%;
   (d) silicon dioxide (SiO2) NOT greater than 1.3%;
   (e) zirconian oxide (ZrO2) NOT greater than 1.8%;
   (f) carbon (C) NOT greater than 0.5%;
   (g) aluminium trioxide (Al2O3) NOT less than 3% and NOT greater
       14.5%;
   (h) bulk density NOT less than 2.8 g/cu cm;
   (i) cold crushing strength NOT less than 50 MPa

REFRACTORY BRICKS AND SHAPES, having all of the following:
   (a) magnesia (MgO) content 55% OR greater;
   (b) chromium oxide (Cr203) content 18% OR greater;
   (c) silica (SiO2) content 1.7% OR less;

REFRACTORY BRICKS AND SHAPES, STEEL MAKING VACUUM DEGASSER, based
 on magnesia and chrome, fired, having ALL of the following:
   (a) magnesia (MgO) content 55% OR greater;
   (b) chromium oxide (Cr203) content 18% OR greater;
   (c) silica (Si02) content 1.7% OR less;
   (d) bulk density 3.15 grams per cubic centimetre OR greater;
   (e) apparent porosity 17% OR less;
   (f) cold crushing strength 40 newton/square millimetre (N/mm2)
       OR greater

REFRACTORIES, silica, having ALL of the following characteristics:
   (a) a silica content NOT less than 90%;
   (b) a bulk density NOT less than 1.5 g/cu cm;
   (c) a design service temperature rating of 1 500 degrees C or
       greater

FIREBRICK, INSULATING, having ALL of the following:
   (a) bulk density NOT exceeding 0-65 g/cu cm;
   (b) a raw material base of kaolinite clay with or without alumina
       additions;
   (c) a mineral composition of NOT less than 35% by weight of
       alumina and NOT more than 55% by weight of silica;
   (d) a thermal conductivity NOT exceeding 0.23 W/mK (watts per
       meter Kelvin) measured at 800 degrees C

BRICKS AND/OR SHAPES, REFRACTORY, FIRED, INSULATING, BLAST 
FURNACE HOT BLAST OR BUSTLE MAIN, having ALL of the following:
  (a) alumina (Al2O3) content NOT less than 60%;
  (b) silica (SiO2) content NOT less than 30%;
  (c) bulk density NOT less than 2.40 g/cm3;
  (d) apparent porosity NOT greater than 18%;
  (e) machine pressed;
  (f) ceramic bond

BRICKS AND/OR SHAPES, REFRACTORY, BLAST FURNACE, fired, having 
ALL of the following:
(a) alumina (Al2O3) content NOT less than 66%;
(b) bulk density NOT less than 2.64%;
(c) apparent porosity NOT greater than 20%;
(d) cold crushing strength NOT less than 34 MPa;
(e) free carbon (F.C) content NOT less than 10% and NOT greater 
than 20%;
(f) silicon carbide (SiC) content NOT less than 2% and NOT   
greater than 5%

REFRACTORY TILES AND/OR BRICKS, having BOTH of the following:
  (a) alumina content NOT less than 99%; 
  (b) iron oxide AND silicon dioxide content combined NOT   
      greater than 1%

BRICKS AND/OR BLOCKS AND/OR TILES AND/OR SHAPES, REFRACTORY 
AND/OR INSULATING, WALKING BEAM FURNACE AND/OR STEEL MAKING 
PLANT, having BOTH of the following: 
  (a) alumina (Al2O3) content NOT less than 25 %;
  (b) silica (SiO2) content NOT less than 26 %

BRICKS AND/OR BLOCKS AND/OR TILES AND/OR SHAPES, REFRACTORY 
AND/OR INSULATING, BLAST FURNACE AND/OR STEEL MAKING PLANT, 
having BOTH of the following: 
  (a) alumina (Al2O3) content NOT less than 25%;
  (b) silica (SiO2) content NOT less than 26%

REFRACTORY BRICKS, having ALL of the following:
  (a) alumina content NOT less than 54%;
  (b) silica content NOT less than 40%;
  (c) ferrous oxide content NOT greater than 1.5%;
  (d) bulk density NOT greater than 1.2 g/cm?

REFRACTORY BRICKS, having ALL of the following:
  (a) alumina content NOT less than 45%;
  (b) silica content NOT greater than 50%;
  (c) ferrous oxide content NOT greater than 2%;
  (d) bulk density NOT less 2.30g/cm3

REFRACTORY BRICKS AND/OR BLOCKS AND/OR TILES, having ALL of the 
following:
  (a) aluminium oxide content by weight NOT less than  
      18 per cent;
  (b) ferrous oxide content by weight NOT greater than  
      10 per cent;
  (c) potassium oxide content by weight NOT greater than 
      3.5 per cent;
  (d) bulk density NOT less than 1.94 grams per cubic 
      centimetre;
  (e) apparent porosity NOT greater than 21.5 per cent

REFRACTORY BRICKS AND SHAPES, alumina spinel, having ALL of the 
following:
  (a) alumina (Al2O3) content greater than 80%;
  (b) magnesia (MgO) content NOT less than 4.5% and NOT greater  
      than 8.0%;
  (c) silica (SiO2) content NOT greater than 3.0%;
  (d) apparent porosity greater than 12%;
  (e) bulk density greater than 3%

RERACTORY BRICKS AND SHAPES, VERTICAL COMBUSTION CHAMBER, 
being EITHER of the following:
  (a) refractory bricks having AI2O3 content by weight NOT 
      less than 60%; 
  (b) refractory wedges

BRICKS, REFRACTORY including ALL of the following:
  (a) silicon dioxide content NOT less than 48% and NOT greater 
      than 56%;
  (b) aluminium oxide content NOT less than 39% and NOT greater 
      than 47%;
  (c) iron oxide content NOT greater than 2.5%;
  (d) titanium dioxide content NOT greater than 2%

REFRACTORY BRICKS AND/OR SHAPES, having ALL of the following:
  (a) alumina content NOT less than 70%;
  (b) silica content NOT greater than 30%;
  (c) compressive strength NOT less than 80 MPa;
  (d) density NOT less than 2 500 kg per cubic metre;
  (e) porosity greater than 15%,
with OR without elements AND/OR compounds other than alumina AND 
silica NOT exceeding 5% per element AND/OR compound

BRICKS, REFRACTORY including ALL of the following:
  (a) silicon dioxide content NOT less than 35% and NOT greater
      than 75%;
  (b) aluminium oxide content NOT less than 20% and NOT greater
      than 25%;
  (c) iron oxide content less than 3%;
  (d) sodium oxide AND potassium oxide content less than 5%

BRICKS, REFRACTORY CHECKER

REFRACTORY BRICKS, including ALL of the following:
  (a) alumina (Al203) content being EITHER of the following:
          (i) NOT less than 68%;
         (ii) NOT less than 40% in mixture with NOT
              less than 37% silica (Si02);
  (b) bulk density NOT less than 2 280 kg per cubic metre;
  (c) apparent porosity NOT greater than 22%

REFRACTORY BLOCKS, fused cast, having ALL of the following:
  (a) aluminium oxide (alumina Al2O3) content NOT less than 65%;
  (b) amorphous silicon dioxide (silica SiO2) content NOT less
      than 5%;
  (c) zirconium dioxide (zirconia ZRO2) content NOT less
      than 4%;
  (d) iron (lll) oxide (ferric oxide Fe2O3) content NOT
      greater than 11%

REFRACTORY BLOCKS AND/OR SHAPES AND/OR TILES, GLASS MELTING 
FURNACE

BLOCKS AND/OR SHAPES, REFRACTORY, cordierite, dry pressed, 
having ALL of the following:
  (a) alumina (A1203) content NOT less than 25%;
  (b) magnesium oxide (Mg0) content NOT less than 1% and NOT
      greater 10%;
  (c) Dimensional tolerances:
        (i) NOT greater than 1.0% for shapes having ANY side
            greater than 150 mm; 
       (ii) NOT greater than 1.5 mm for shapes having ANY side 
            less than 150 mm;
      (iii) diagonal warpage NOT greater than 1.0%;
  (d) thermal shock resistance greater than 30 cycles;
  (e) reversible thermal expansion NOT less than 0.25% and NOT
      greater than 0.7% at 1 000 degrees C;
  (f) silica (Si02) content NOT less than 26%

H-CASSETTE, REFRACTORY, KILN, having ALL of the following:
  (a) alumina content NOT less than 36%;
  (b) silica content NOT less than 50%;
  (c) ferrous oxide content NOT greater than 1.5%; 
  (d) modulus of rupture at 1 200 degrees celsius NOT less than
      17 MPa;
  (e) bulk density NOT less than 1.85 g/cm3 and NOT greater than
      2.2 g/cm3

BLOCKS, REFRACTORY, extruded, having ALL of the following:
  (a) aluminia (Al2O3) content NOT less than 34%;
  (b) silica (SiO2) content NOT less than 55%;
  (c) ferric oxide (Fe2O3) content NOT greater than 2.5%;
  (d) bulk density NOT greater than 2.2 g/cm3;
  (e) cold crushing strength NOT less than 19 MPA

TILES, REFRACTORY, PRESSED, having ALL of the following:
  (a) aluminia (Al2O3) content NOT less then 29%;
  (b) silica (SiO2) content NOT less then 55%;
  (c) ferric oxide (Fe2O3) content NOT greater than 2.5%;
  (d) bulk density NOT greater than 2 g/cm3;
  (e) cold crushing strength NOT less then 19 MPa

BRICKS AND/OR SHAPES, REFRACTORY, FIRED, INSULATING, BLAST 
FURNACE HOT BLAST OR BUSTLE MAIN, having ALL of the following:
  (a) alumina (Al2O3) content NOT less than 60%;
  (b) silica (SiO2) content NOT less than  30%;
  (c) bulk density NOT less than 2.40 g/cm3;
  (d) apparent porosity NOT greater than 21%;
  (e) hand made;
  (f) ceramic bond

BRICKS AND/OR SHAPES, REFRACTORY, FIRED, INSULATING, BLAST 
FURNACE HOT BLAST OR BUSTLE MAIN, having ALL of the following:
  (a) alumina (Al2O3) content NOT less than 60%;
  (b) silica (SiO2) content NOT less than 30%;
  (c) bulk density NOT less than 2.40 g/cm3;
  (d) apparent porosity NOT greater than 18%;
  (e) machine pressed;
  (f) ceramic bond

BRICKS AND/OR SHAPES, REFRACTORY, FIRED, INSULATING, BLAST 
FURNACE HOT BLAST OR BUSTLE MAIN, having ALL of the following:
  (a) alumina (Al2O3) content NOT less than 31%;
  (b) silica (SiO2) content NOT less than 45%;
  (c) ferrous oxide (Fe2O3) content NOT greater than 2.5%;
  (d) bulk density NOT greater than 1.2 g/cm3;
  (e) ceramic bond

BRICKS AND/OR SHAPES, REFRACTORY, FIRED, INSULATING, BLAST 
FURNACE HOT BLAST OR BUSTLE MAIN, having ALL of the following:
  (a) alumina (Al2O3) content NOT less than 41%;
  (b) Silica (SiO2) content NOT less than 35%;
  (c) ferrous oxide (Fe2O3) content NOT greater than 1.0%;
  (d) bulk density NOT greater than 0.6 g/cm3;
  (e) ceramic bond

BRICKS AND/OR SHAPES, REFRACTORY, BLAST FURNACE, fired, having 
ALL of the following:
(a) alumina (Al2O3) content NOT less than 66%;
(b) bulk density NOT less than 2.64%;
(c) apparent porosity NOT greater than 20%;
(d) cold crushing strength NOT less than 34 MPa;
(e) free carbon (F.C) content NOT less than 10% and NOT greater 
than 20%;
(f) silicon carbide (SiC) content NOT less than 2% and NOT   
greater than 5%

REFRACTORY BLOCKS, FUSED CAST, having ALL of the following:
   (a) alumina content greater than 65%;
   (b) silica content greater than 15%;
   (c) zirconia content greater than 4%;
   (d) compressive strength greater than 200 MPa

CHECKER BRICKS, COKE OVEN, having ALL of the following:
   (a) alumina (Al2O3) content equal to OR greater than 42%;
   (b) bulk density equal to OR greater than 2.1 grams/cubic
       centimetre;
   (c) cold crushing strength equal to OR greater than 30 MPa

REFRACTORIES, SILICA, having BOTH of the following:
   (a) silica content exceeding 90%;
   (b) bulk density exceeding 0.60 g/cubic centimetre

FIREBRICKS INSULATING, having BOTH of the following characteristics:
   (a) a bulk density NOT exceeding 1.7 g/cubic centimetre;
   (b) a mineral composition of one or more of the following:
           (i) NOT less than 40% by weight of silicon dioxide;
          (ii) NOT less than 40% by weight of aluminium oxide;
         (iii) NOT less than 40% by weight of silicon dioxide and
               aluminium oxide in combination

REFRACTORIES, silicon carbide, having a silicon carbide content
 of NOT less than 50%, bonded by ANY of the following methods:
   (a) self bonded;
   (b) silicon nitride bonded;
   (c) silicon oxynitride bonded

REFRACTORIES, having a content of NOT less than 50% by weight of
 carbon

REFRACTORY TILES, hexagonal, with OR without 19 axial holes, 
including BOTH of the following:
  (a) zirconium oxide content by weight NOT less than 80 %;
  (b) service temperature NOT less than 1 650 degree Celsius

RERACTORY BRICKS AND SHAPES, VERTICAL COMBUSTION CHAMBER, 
Al2O3 content by weight NOT greater than 46%

REFRACTORY PRODUCTS, fused cast alumina zirconia silica, having ALL
 of the following:
   (a) silica 5% to 20%;
   (b) aluminium 45% to 60%;
   (c) zircon 30% to 45%;
   (d) specific gravity within the range 3 500 kg/cubic metre to
       4 150 kg/cubic metre

TUBES, of spectroscopic graphite, coated with pyrolytic graphite,
 being a component of graphite furnace atomic absorption
 spectrometers

REFRACTORIES, glass forehearth or furnace feeder expendables

CRUCIBLES OR RETORTS, carbon bonded, having a silicon carbide
 content exceeding 35%

REFRACTORY GOODS, incorporating alumina fibres, having BOTH of
 the following characteristics:
   (a) a content NOT less than 75% by weight of aluminium oxide;
   (b) a design service temperature rating of 1 500 degrees C or
       greater

NOZZLES, submerged entry, graphitised alumina

PLATES, sliding gate nozzle

CERAMIC ANCHORS, VERTICAL COMBUSTION CHAMBER, AI2O3 content by 
weight NOT less than 64%

ROLLERS, fused silica

TUNDISH PIPES AND TUNDISH SHROUDS

REFRACTORY GOODS, FIRED, being ANY of the following:
   (a) casting cones;
   (b) nozzles;
   (c) stoppers;
   (d) protection tubes;
   (e) seats;
   (f) shrouds;
   (g) starter tubes;
   (h) sensor covers;
   (i) entry rings

SLIDE GATE PLATES AND/OR LADLE PLATES, REFRACTORY

FILTERS, ALUMINIUM CASTING, OF CERAMIC FOAM

FILTERS, CERAMIC FOAM, FERROUS FOUNDRY

REFRACTORIES, silicon carbide, having a silicon carbide
 content of NOT less than 50%, bonded by EITHER of the following
 methods:
   a) self bonded;
   b) silicon oxynitride bonded

TUBES, silicon carbide, unmachined, sintered

REFRACTORY GOODS, zirconium oxide content NOT less than 85%,
 design service temperature 1 600 degrees C or greater

CRUCIBLES OR RETORTS, carbon bonded, having a silicon carbide
 content exceeding 35%

EVAPORATION BOATS, METALLISATION APPLICATION, composite ceramic, 
having two OR more of the following components:
  (a) titanium diboride;
  (b) boron nitride;
  (c) aluminium nitride

CERAMIC WELD BACKING

SAMPLERS, immersion, molten metal, having a ceramic mould

PARTS AND/OR ACCESSORIES, REFRACTORY AND FOUNDRY, MOLTEN METAL  
PLANT, being ANY of the following:
  (a) crucibles;
  (b) launders;
  (c) sheaths;
  (d) tubes;
  (e) bowls;
  (f) stoppers;
  (g) tools;
  (h) transporter shapes

REFRACTORY GOODS, FIRED, being ANY of the following:
   (a) casting cones;
   (b) nozzles;
   (c) stoppers;
   (d) protection tubes;
   (e) seats;
   (f) shrouds;
   (g) starter tubes;
   (h) sensor covers;
   (i) entry rings

SLIDE GATE PLATES AND/OR LADLE PLATES, REFRACTORY

PIPES AND PIPE FITTINGS, rigid, vitrified clay, manufactured
 in accordance with international standard BSEN 295:1991

DEWATERING ELEMENTS, PAPER PULP AND PAPER MAKING, being ANY of
 the following:
   (a) blades;
   (b) foils;
   (c) forming boards;
   (d) deflectors;
   (e) suction box covers;
   (f) felt wear strips and blade strips

NOZZLES, ceramic, agricultural sprayer

LINERS, PIPE OR TUBE, alumina ceramic, having ALL of the 
following:
  (a) rubber backing;
  (b) Mohs rating NOT less than 9; 
  (c) alumina content NOT less than 85%

PARTS, LABORATORY FURNACE, ceramic, having a hardness NOT less 
than 9 on the Mohs, being ANY of the following:
  (a) crucible holders, whether OR not assembled;
  (b) mould holders, whether OR not assembled;
  (c) shafts

DISCS, TAP, ceramic

CERAMIC TILES, rubber backed, having an alumina content by 
weight NOT less than 85%

LINERS, ALUMINA CERAMIC, whether or not in tile form

GRINDING MEDIA, ALUMINA

KILN FURNITURE, being ANY of the following:
   (a) pin cranks;
   (b) tile cranks;
   (c) vertical plate setters;
   (d) stilts;
   (e) spurs;
   (f) star stilts;
   (g) cone stands;
   (h) plate setters

BALLS, catalyst support

GRINDING MEDIA, alumina, cylindrical or spherical, having a
 specific gravity of 3.2 or greater and a dia exceeding 3 mm

GRINDING MEDIA, zirconium oxide

INSERTS, METAL CUTTING TOOL

DEWATERING ELEMENTS, PAPER PULP AND PAPER MAKING, being ANY of the
 following:
   (a) blades;
   (b) foils;
   (c) forming boards;
   (d) deflectors;
   (e) suction box covers;
   (f) felt wear strips and Uhle box strips

TAP CERAMIC DISC CARTRIDGE KITS, consisting of upper and lower
 ceramic discs and one or more of the following:
   (a) washers;
   (b) clips;
   (c) gaskets;
   (d) screens

KILN FURNITURE, REFRACTORY, cordierite mullite, pressed and
 extruded, comprising ANY of the following:
   (a) batts;
   (b) props, but excluding extruded props;
   (c) caps;
   (d) interlocking furniture

NOZZLES, ceramic, agricultural sprayer

INERT TOPPING MATERIAL, CATALYST PROTECTION, being a magnesium 
alumina spinel

PROPPANT, HYDRAULIC FRACTURING, ceramic, granular

PROPPANTS, ceramic, having a bulk density NOT less than 1.45 
grams per cubic centimetre

AIRSTONES

BEADS, GRINDING, CERAMIC

FURNITURE, KILN, cordierite composition, pressed, comprising ALL 
of the following: 
 (a) magnesium oxide (MgO) NOT less than 3.5% and NOT greater 
     than 6% by weight;
 (b) aluminium oxide NOT less than 30% and NOT greater than 50%
     by weight;
 (c) thermal expansion at 1 000 degrees celsius NOT greater 
     than 0.41%; 
 (d) bulk density NOT less than 2.00 and NOT greater than 2.25
     grams per cubic centimetre.

CERAMIC MEDIA, REGENERATIVE THERMAL OXIDISER

ELEMENTS, CERAMIC FILTER

CERAMIC BLOCKS, HONEYCOMB, REGENERATIVE THERMAL OXIDISER

CORDIERITE CERAMIC SUBSTRATE, having a cellular internal structure

CATALYST PROTECTION MEDIA, fused alumina, in the form of fluted
 rings

MACERATING TOILETS, including ALL of the following:
  (a) toilet bowl AND pan with soft close seat;
  (b) integrated pump AND macerator;
  (c) dual flush button;
  (d) electric motor

BIDETS, ceramic, floor mounted OR wall hung, with OR without 
mounting kits

TOILET PANS, vitreous china, with OR without ANY of the 
following:
  (a) toilet seats;
  (b) pan blanking caps;
  (c) pan connectors;
  (d) fixing hardware

WASH BASINS, vitreous china

HAND BASINS, BATHROOM, vitreous china

URINALS, with OR without water flush mechanism

TOILET SUITES, including ALL of the following:
  (a) pan;
  (b) cistern;
  (c) seat with hinged lid

TOILET CISTERNS, vitreous china, including BOTH of the following:
  (a) complying with Australian/New Zealand Standard 1172.2  
     (AS/NZS 1172.2);
  (b) NOT less than four star rating as required by the 
      Australian Water Efficiency Labelling and Standards Act
      2005 WELS Act 2005)

TOILET PANS, vitreous china, including BOTH of the following:
  (a) complying with Australian/New Zealand Standard 1172.1
      (AS/NZS 1172.1);
  (b) NOT less than four star rating as required by the
      Australian Water Efficiency Labelling and Standards Act
      2005 (WELS Act 2005)

BASINS, BATHROOM, vitreous china, excluding basins with 
integrated cabinets, including BOTH of the following: 
  (a) complying with Australian Standard 1976-1992 (AS 1976-
      1992;   
  (b) chrome plated brass basin waste

TOILET CISTERNS, vitreous china, including ALL of the following:
  (a) complying with Australian/New Zealand Standard 6400:2005
      (AS/NZS 6400:2005);
  (b) NOT less than 4 star rating as required by the Australian
      Water Efficiency Labelling and Standards Act 2005 (WELLS
      Act 2005); 
  (c) complying with Australian Standard 1976-1992 (AS 1976- 
      1992);
  (d) inlet AND outlet valves

TOILET PANS, vitreous china, including ALL of the following:
  (a) complying with Australian Standard 1172.1-2005 (AS 1172.1-
      2005);
  (b) complying with Australian/New Zealand Standard 6400:2005  
      (AS/NZS 6400:2005); 
  (c) NOT less than 4 star rating as required by the Australian
      Water Efficiency Labelling and Standards Act 2005 (WELLS
      Act 2005);
  (d) complying with Australian Standard 1976-1992 (AS 1976-1992)

MARINE TOILETS, electric pump OR manual pump

MARINE TOILETS, having EITHER of the following:
  (a) electric powered diaphragm pump; 
  (b) hand powered piston pump

URINALS, WATER-FREE, porcelain

WASH BASINS, vitreous china, having an integrated bench top

WASH BASINS, fire clay, with OR without ANY of the following:
 (a) waste plugs;
 (b) overflow rings;
 (c) fitting hardware, including ANY of the following:
       (i) bolts AND/OR nuts;
      (ii) screws AND/OR screw inserts AND/OR screw covers;
     (iii) washers AND/OR spacers

KITCHENWARE, bone china, being ANY of the following:
  (a) bag dispensers;
  (b) bottles; 
  (c) cutlery or kitchen utensils stands and/or racks and/or
      trays; 
  (d) food or cake domes; 
  (e) glass holding racks; 
  (f) wrapping holders and/or foil holders; 
  (g) jugs; 
  (h) non electric coffee pots; 
  (i) paper towel holders; 
  (j) plate racks and/or holders; 
  (k) preserving pans and/or jars; 
  (l) salad washers; 
  (m) spice or condiment racks and/or stands; 
  (n) splatter screens and/or guards;
  (o) food bowl stands; 
  (p) storage jars or storage caddies; 
  (q) tea infusers; 
  (r) trivets

MONEY BOXES, ceramic

THIMBLES, dressmakers" or tailors"

MUGS, ceramic

BAKING DISHES, ceramic stoneware, having BOTH of the following:
  (a) ceramic base;
  (b) polypropylene lid with a silicon seal AND a venting valve

KITCHENWARE, being canisters with OR without spoon

BAKING BEADS, ceramic

SETS, KITCHENWARE, consisting of ALL of the following:
  (a) ceramic pizza stone;
  (b) serving rack;
  (c) pizza cutter

BOWLS AND/OR SAUCERS, PET FOOD, ceramic

PORCELAIN SLABS, unglazed, with OR without fibreglass mesh 
backing, having ALL of the following:
  (a) length NOT less than 3 000 mm;
  (b) width NOT greater than 1 500 mm;
  (c) thickness NOT less than 3 mm and NOT greater than 6 mm

SLABS, porcelain, unglazed, with OR without fibreglass mesh 
backing, having ALL of the following:
  (a) length NOT less than 3 240 mm;
  (b) width NOT greater than 1 620 mm;
  (c) thickness NOT less than 12 mm and NOT greater than 20 mm

HANDLES OR KNOBS, FURNITURE OR CABINET

CERAMIC LOGSETS

FACADE PANELS, ceramic, perforated, having BOTH of the following:
  (a) length NOT less than 750 mm;
  (b) internal cavities NOT less than 15 % of the cross-
      sectional area

SLABS, ceramic, having ALL of the following:
 (a) length NOT greater than 3 500 mm;
 (b) width NOT greater than 2 100 mm;
 (c) thickness NOT less than 4 mm and NOT greater than 40 mm

SLABS, ceramic, having ALL of the following:
  (a) length NOT greater than 3 370 mm;
  (b) width NOT greater than 1 680 mm;
  (c) thickness NOT less than 4 mm and NOT greater than   
      40 mm

PORCELAIN SLABS, Having ALL of the following:
  (a) length NOT greater than 3 800 mm;
  (b) width NOT greater than 1 800 mm;
  (c) thickness NOT greater than 35 mm

PORCELAIN SLABS, polished, having ALL of the following:
  (a) length NOT greater than 3 800 mm;
  (b) width NOT greater than 1 800 mm;
  (c) thickness NOT greater than 35 mm

PORCELAIN SLABS, unglazed, having ALL of the following:
  (a) length NOT less than 3 230 mm;
  (b) width NOT less than 1 200 mm;
  (c) thickness NOT less than 3 mm and NOT greater than 12 mm

PORCELAIN SLABS, glazed, having ALL of the following:
  (a) length NOT less than 3 230 mm;
  (b) width NOT less than 1 200 mm;
  (c) thickness NOT less than 3 mm and NOT greater than 12 mm

CERAMIC SLABS, unglazed, having ALL of the following:
  (a) length NOT greater than 3 300 mm;
  (b) width NOT greater than 1 500 mm;
  (c) thickness NOT less than 6 mm and NOT greater than 35 mm

CERAMIC SLABS, having ALL of the following:
  (a) length NOT greater than 3 300 mm;
  (b) width NOT greater than 1 500 mm;
  (c) thickness NOT less than 4 mm and NOT greater than 35 mm

PORCELAIN SLABS, unglazed, having ALL of the following:
  (a) length NOT greater than 1 500 mm;
  (b) width NOT greater than 1 500 mm;
  (c) thickness NOT less than 3 mm and NOT greater than 6 mm

CERAMIC BLOCKS, DENTAL INLAY, ONLAY, VENEER AND CROWN MAKING, 
incorporating metal holders

PLATES AND/OR PANELS AND/OR TILES, BALLISTIC ARMOUR, silicon 
carbide AND boron carbide

SAUCERS, PLANTER POT, terracotta

PLANTER POTS, CERAMIC