Tariff Concession Orders

POLYETHYLENE, crosslinkable, having ALL of the following:
   (a) compound form containing thermal stabilisers and organic
       peroxide;
   (b) density of 920 kg/cu m by test method ASTMD 792;
   (c) complying with AS1429 - 1985

POLYETHYLENE RESIN, having ALL of the following features:
      (a) density less than 915 kg/m3 ( ASTM D1505 ) ;
      (b) melt flow index (MFI) NOT less than 5.0 ( ASTM D1238 (FR-E)

RESINS, low density polyethylene (LDPE), having ALL of the 
following:
  (a) density NOT less than 0.915g/ cm? @ 23?C and NOT greater 
      than 0.924 g/ cm? @ 23?C, complying with American 
      Society for Testing and Materials standard D 1505 (ASTM D-
      1505);
  (b) crystalline melting point NOT less than 100 ?C and NOT 
      greater than 105 ?C, complying with American Society for  
      Testing and Materials standard E 794 (ASTM E-794);
  (c) vicat softening point NOT less than 80 ?C and NOT greater 
      than 85 ?C, complying with American Society for 
      Testing and Materials standard D 1525 (ASTM D-1525);
  (d) melt flow index NOT less than 50 g/10 min and NOT greater 
      than 85 g/10 min, complying with American Society for 
      Testing and Materials standard D 1238 (ASTM D-1238)

RESINS, being unpigmented linear low density polyethylene, in 
powder OR pelletised form, having BOTH of the following:
  (a) melt flow rate NOT less than 40.0 g/10 min and NOT greater 
      than 60.0 g/10 min, complying with American Society for 
      Testing and Materials Standard D1238 (ASTM D1238), 190 
      degrees Celsius/2.16 kg;
  (b) density NOT less than 924kg/m3 and NOT greater than 
      928kg/m3, complying with American Society for Testing 
      and Materials Standard D1505 (ASTM D1505)

RESINS, LOW DENSITY POLYETHYLENE (LDPE), having ALL of the 
following:
  (a) density NOT less than 910 kg/m3 and NOT greater than 930 
kg/m3, complying with ANY of the following standards:
          (i) American Society for Testing and Materials     
              Standard D1505 (ASTM D1505);
         (ii) American Society for Testing and Materials         
              Standard D792 (ASTM D792);
        (iii) International Organisation for Standardisation 
              Standard 1183 (ISO 1183),
  (b) vicat softening point NOT less than 80 degrees Celsius and 
NOT greater than 105 degrees Celsius, complying with ANY of the 
following standards:
          (i) American Society for Testing and Materials 
              Standard D 1525 (ASTM D1525);
         (ii) International Organisation for Standardisation 
              Standard 306 (ISO 306),
  (b) melt flow rate (MFR)at 190 degrees Celsius and 2.16 kg,  
NOT less than 0.1 g/10 minute and NOT greater than 10 g/10 
minute, complying with ANY of the following standards: 
          (i) American Society for Testing and  Materials     
              Standard D1238 (ASTM D1238); 
         (ii) International  Organisation for Standardisation 
             Standard 1133 (ISO 1133)

RESINS, linear low density polyethylene, pelletised form 
with OR without UV stabiliser, having ALL of the following:
  (a) melt flow NOT less than 2.0 g/10 min and NOT greater than
      6.0 g/10 @ 190 degrees Celsius / 2.16kg;
  (b) density NOT less than 0.92 g/cm3 and NOT greater than 
      0.94 g/cm3

RESINS, being unpigmented low density polyethylene, in 
pelletised form, having BOTH of the following:
  (a) melt flow rate NOT less than 0.6 g/10 min and NOT greater
      than 0.9 g/10 min, complying with American Society for
      Testing and Materials standard D 1238 (ASTM D1238), 
      190 degrees Celsius/2.16 kg;
  (b) density NOT less than 922 kg/m3 and NOT greater than 
      924 kg/m3, complying with American Society for Testing and 
      Materials standard D 792 (ASTM D792)

RESINS, being unpigmented low density polyethylene, in 
pelletised form, having BOTH of the following:
  (a) melt flow rate NOT less than 1.7g/10 min NOT greater than
      2.3g/10 min, complying with American Society for Testing  
      and Materials standard  D 1238 (ASTM D 1238), 190 degrees  
      Celsius/2.16 kg;
  (b) density NOT less than 922 kg/m3 and NOT greater than 924
      kg/m3, complying with American Society for Testing and
      Materials standard D 792 (ASTM  792)

LINEAR LOW DENSITY POLYETHYLENE (LLDPE), having ALL of the 
following:
  (a) density NOT less than 0.918 g/cm3 and NOT greater than 
      0.928 g/cm3, complying with American Society for Testing 
      and Materials standard D 792 (ASTM D-792);
  (b) crystalline melting point NOT less than 100 degrees 
      Celsius and NOT greater than 125 degrees Celsius,   
      complying with American Society for Testing and Materials 
      standard E 794 (ASTM E-794);
  (c) Vicat softening point NOT less than 80 degrees Celsius and 
      NOT greater than 105 degrees Celsius, complying with 
      American Society for Testing and Materials standard 
      D 1525 (ASTM D-1525) (A120);
  (d) melt flow index NOT less than 0.8 g/10 min and NOT greater 
      than 3.5 g/10min (190 degrees Celsius/2.16kg), complying  
      with American Society for Testing and Materials standard D 
      1238 (ASTM D-1238)

LOW DENSITY POLYETHYLENE (LDPE), having ALL of the following:
  (a) density NOT less than 0.918 g/cm3 and NOT greater than 
      0.928 g/cm3, complying with American Society for Testing 
      and Materials standard D 1505 (ASTM D-1505;
  (b) crystalline melting point NOT less than 100 degrees 
      Celsius and NOT greater than 125 
      degrees Celsius, complying with American Society for 
      Testing and Materials standard E 794 (ASTM E-794;
  (c) Vicat softening point NOT less than 80 degrees Celsius and 
      NOT greater than 105 degrees Celsius, complying with 
      American Society for Testing and Materials standard 
      D 1525 (ASTM D-1525;
  (d) melt flow index NOT less than 0.3 g/10 min and NOT greater 
      than 8 g/10min, complying with American Society for 
      Testing and Materials standard D 1238 
      (ASTM D-1238)

RESINS, POLYETHYLENE, having BOTH of the following:
  (a) density less than 905 kg/m3;
  (b) melt flow index (MFI) NOT less than 0.8 g/10 min

POLYETHYLENE COMPOUND, peroxide cross linkable, carbon black filled

RESINS, HIGH DENSITY POLYETHYLENE (HDPE), having ALL of the 
following:
  (a) density (at 23 degrees Celsius) NOT less than 945 kg/m3
      and NOT greater than 970 kg/m3, complying with ANY of the
      following standards:
      (i)American Society for Testing and Materials Standard 
      D1505 (ASTM D1505);
     (ii)American Society for Testing and Materials
      Standard D792 (ASTM D792);    
     (iii)International Organisation for
      Standardisation Standard 1183 (ISO 1183),
  (b) melt flow rate (MFR) (at 190 degrees Celsius and 5 kg)
      NOT less than 0.15 g/10 minute and NOT greater than 
      0.50 g/10 minute, complying with EITHER of the following
      standards: (i)American Society for Testing and Materials
      Standard D1238 (ASTM D1238) 
     (ii)International Organisation for Standardisation Standard 
      1133 (ISO 1133)

RESINS, HIGH DENSITY POLYETHYLENE (HDPE), having ALL of the 
following:
  (a) density (at 23 degrees Celsius) NOT less than 940 kg/m3 
      and NOT greater than 975 kg/m3, complying with ANY of the 
      following standards;
          (i) American Society for Testing and Materials     
              standard D1505 (ASTM D1505);
         (ii) American Society for Testing and Materials  
              standard D792 (ASTM D792);
        (iii) International organisation for Standardisation 
              standard 1183 (ISO 1183)
  (b) melt flow rate (MFR) (at 190 degrees Celsius and 21.6 kg) 
      NOT less than 4.0 g/10 minute and NOT greater than 60.0 
      g/10 minute, complying with EITHER of the following 
      standards;
          (i) American Society for Testing and Materials 
              standard D1238 (ASTM D1238);
         (ii) International Organisation for Standardisation   
              standard 1133 (ISO 1133)

RESINS, HIGH DENSITY POLYETHYLENE (HDPE), having ALL of the 
following:
  (a) density (at 23 degrees Celsius) NOT less than 940 kg/m3
      and NOT greater than 975kg/m3, complying with ANY of the
      following standards;
          (i) American Society for Testing and Materials
              standard D1505 (ASTM D1505);
         (ii) American Society for Testing and Materials
              standard D792 (ASTM D792);
        (iii) International Organisation for Standardisation
              standard 1183 (ISO 1183);
  (b) melt flow rate (MFR) (at 190 degrees Celsius and 2.16 kg)
      NOT less than 2.0 g/10 minute and NOT greater than 
      60.0 g/10 minute, complying with EITHER of the following
      standards;
          (i) American Society for Testing and Materials
              standard D1238 (ASTM D1238);
         (ii) International Organisation for Standardisation
              standard 1133 (ISO 1133)

RESINS, HIGH DENSITY POLYETHYLENE (HDPE), having ALL of the 
following:
  (a) density (at 23 degrees Celsius) NOT less than 940 kg/m3
      and NOT greater than 975kg/m3, complying with ANY of the
      following standards:
          (i) American Society for Testing and Materials
              standard D1505 (ASTM D1505); 
         (ii) American Society for Testing and Materials
              standard D792 (ASTM D792);
        (iii) International Organisation for Standardisation
              standard 1183 (ISO 1183);
  (b) melt flow rate (MFR) (at 190 degrees Celsius and 21.6 kg)
      NOT less than 4.0 g/10 minute and NOT greater than 
      55.0 g/10 minute, complying with EITHER of the following
      Standards:
          (i) American Society for Testing and Materials
              standard D1238 (ASTM D1238);
         (ii) International Organisation for Standardisation
              standard 1133 (ISO 1133)

RESINS, HIGH DENSITY POLYETHYLENE (HDPE), having ALL of 
the following:
  (a) density NOT less than 0.955 g/cm3 and NOT greater than
      0.958 g/cm3, complying with American Society for Testing
      and Materials Standard D-1505 (ASTM-1505);
  (b) melt flow index NOT less than 17 g/10 min (MI, 190 degrees
      Celsius/2.16kg) and NOT greater than 23 g/10 min (MI, 190
      degrees Celsius/2.16kg), complying with American Society
      for Testing and Materials Standard D-1238 (ASTM-D1238);
  (c) brittleness temperature <-75 degrees Celsius, complying
      with American Society for Testing and Materials Standard 
      D-746 (ASTM-D746);
  (d) elongation at break >200%, complying with American Society
      for Testing and Materials Standard D-638 (ASTM-D638)

GRANULES, HIGH-DENSITY POLYETHYLENE, including ALL of 
the following:
  (a) density NOT less than 0.956g/cm3 and NOT greater than
      0.964g/cm3, complying with International Organisation for 
      Standardisation standard ISO 1183 (ISO 1183);
  (b) melt flow rate NOT less than 0.18g/10min and NOT greater 
      than 0.3g/10min, complying with American Society for    
      Testing and Materials standard D 1238 (ASTM D 1238), 190 
      degrees Celsius/5.0 kg;
  (c) pellet filling NOT less than 2% carbon black

RESINS, virgin, high density polyethylene, butene type, having 
ALL of the following:
  (a) density NOT less than 0.950 g/cm3 and NOT greater than   
      0.954 g/cm3, complying with International Organization for 
      Standardization Standard 1872-2 (ISO 1872-2);
  (b) melt flow rate NOT less than 0.04 g/10 min and NOT greater
      than 0.06 g/10min, complying with International  
      Organization for Standardization Standard 1872-2 
      (ISO 1872-2), 190 degrees Celsius/2.16kg;
  (c) melt flow rate NOT less than 7.2 g/10 min and NOT greater
      than 10.8 g/10min, complying with International 
      Organization for Standardization Standard 1872-2 
      (ISO 1872-2), 190 degrees Celsius/21.6kg

RESINS, HIGH DENSITY POLYETHYLENE (HDPE), having ALL of the 
following:  
  (a) density NOT less the 0.940 g/cm3 and NOT greater than
      0.960 g/cm3, complying with American Society for Testing 
      and Materials Standard D-1505 (ASTM-1505);
  (b) melt flow index NOT less than 0.015 g/10 min 
      (MI, 190 degrees Celsius/2.16kg) and NOT greater than
      0.40 g/10 min (MI, 190 degrees Celsius/2.16kg), complying 
      with American Society for Testing and Materials Standard 
      D1238 (ASTM-D1238);
  (c) brittleness temperature < -75 degrees Celsius, complying 
      with American Society for Testing and Materials Standard D-
      746 (ASTM-746);
  (d) elongation at break >600%, complying with American Society
      for Testing and Materials Standard D638 Type IV 
      (ASTM-D638 Type IV)

RESINS, HIGH DENSITY POLYETHYLENE (HDPE), having ALL of the 
following:  
  (a) density NOT less than 0.935 g/cm3 and NOT greater than
      0.950 g/cm3, complying with American Society for Testing 
      and Materials Standard D-1505 (ASTM-1505);
  (b) melt flow index NOT less than 0.16 g/10 min 
     (MI, 190 degrees Celsius/2.16kg) and NOT greater than 0.22 
      g/10 min (MI, 190 degrees Celsius/2.16kg), complying with 
      American Society for Testing and Materials Standard D1238 
      (ASTM-D1238);
  (c) brittleness temperature < -75 degrees Celsius, complying 
      with American Society for Testing and Materials Standard D-
      746 ASTM-746);
  (d) elongation at break, (50 mm/min) MD: 500% +/- 5%, TD: 
      660% +/- 5%, complying with American Society for Testing 
      and Materials Standard D882 (ASTM-D882)

RESINS, being unpigmented, high density polyethylene hexene 
copolymer, in pelletised form, having ALL of the following:
  (a) melt flow rate NOT less than 0.20 g/10 min and NOT greater 
      than 0.40 g/10 min, complying with International
      Organisation for Standardisation 1133 (ISO 1133), 190 
      degrees Celsius/5.0 kg;
  (b) density NOT less than 947kg/m3 and NOT greater than 
      952kg/m3, complying with International Organisation for
      Standardisation 1183 (ISO 1183), 23 degrees Celsius;
  (c) flexural modulus NOT less than 950 MPa complying with 
      International Organisation for Standardisation 178 (ISO 
      178)

RESINS, being black pigmented, bimodal high density polyethylene 
hexene copolymer compound, in pelletised form, having ALL of the 
following:
  (a) melt flow rate NOT less than 0.155 g/10 min and NOT 
      greater than 0.195 g/10 min, complying with International
      Organization for Standardization 1133 (ISO 1133), 190 
      degrees Celsius / 5.0 kg;
  (b) density NOT less than 955kg/m3 and NOT greater than 
      964kg/m3, complying with International Organization for
      Standardization 1183 (ISO 1183), 23 degrees Celsius;
  (c) oxidation induction time NOT less than 20 minutes
      complying with International Organization for 
      Standardization 11357-6 (ISO 11357-6), 210 degrees Celsius;
  (d) carbon black content NOT less than 2% and NOT greater 
      than 2.5%, complying with International Organization for
      Standardization 6964 (ISO 6964)

RESINS, bimodal high density polyethylene compound, pigmented 
black, pelletised form, having ALL of the following:
  (a) melt flow rate NOT less than 0.20 g/10 min and NOT greater 
      than 0.30 g/10 min, complying with International
      Organization for Standardization 1133 (ISO 1133), 190 
      degrees Celsius/5.0 kg;
  (b) density NOT less than 955 kg/m3 and NOT greater than 
      965 kg/m3, complying with International Organization for
      Standardization 1183 (ISO 1183);
  (c) oxidation induction time NOT less than 20 minutes, 
      complying with International Organization for  
      Standardization 11357-6 (ISO 11357-6);
  (d) carbon black content NOT less than 2% and NOT greater 
      than 2.5%, complying with International Organization for
      Standardization 6964 (ISO 6964)

RESINS, being pigmented black, high-density polyethylene, in 
pelletised form, having ALL of the following:
  (a) melt flow rate NOT less than 0.35 g/10 min and NOT greater 
      than 0.85 g/10 min, complying with International
      Organisation for Standardisation 1133 (ISO 1133), 190 
      degrees Celsius/5.0 kg
  (b) density NOT less than 956kg/m3 and NOT greater than 
      965kg/m3, complying with International Organisation for
      Standardisation 1183 (ISO 1183), 23 degrees Celsius;
  (c) oxidation induction time NOT less than 20 minutes, 
      complying with International Organisation for 
      Standardisation 11357-6 (ISO 11357-6), 210 degrees Celsius

RESINS, being unpigmented multimodal, high-density polyethylene, 
in pelletised form, having all of the following:
  (a) melt flow rate NOT less than 3.75 g/10 min and NOT greater 
      than 4.25 g/10 min in complying with international 
      standard American Society for Testing and Materials 
      standard D 1238 (ASTM D 1238), 190 degrees Celsius 
      / 2.16 kg;
  (b) environmental stress-cracking of ethylene plastics failure 
      NOT less than 50% /40 Hours, complying with American
      Society for Testing and Materials standard D 1693-B (ASTM 
      D1693-B)

RESINS, high-density polyethylene, unpigmented multimodal, 
pelletised form, having ALL of the following:
  (a) melt flow rate NOT less than 0.70 g/10 min and NOT greater 
      than 0.90 g/10 min, complying with American Society for 
      Testing and Materials standard 1238 (ASTM D 1238), 190 
      degrees Celsius/2.16 kg;
  (b) environmental stress-cracking of ethylene plastics failure 
      NOT less than 50%/750 hours, complying with 
      American Society for Testing and Materials standard D 1693-
      B (ASTM D1693-B);
  (c) full-notch creep test value NOT less than 65 hours, 
complying with 
      International Organization for Standardization 16770 
      (ISO 16770)

RESINS, being unpigmented multimodal, high-density polyethylene, 
in pelletised form, having ALL of the following:
  (a) melt flow rate NOT less than 0.55 g/10 min and NOT greater 
than 0.85 g/10 min complying with American Society for Testing 
and Materials Standard D1238 (ASTM D1238), 190 degrees 
Celsius/2.16 kg;
  (b) density NOT less than 958 kg/m3 and NOT greater than 963 
kg/m3 complying with International Organisation for 
Standardisation 1183 (ISO 1183);
  (c) environmental stress-cracking failure NOT less than 50 per 
cent/72 hours, complying with American Society for Testing and 
Materials Standard D1693-B (ASTM D1693-B)

RESINS, being unpigmented multimodal, high-density polyethylene, 
in pelletised form, having ALL of the following:
  (a) melt flow rate NOT less than 1.25 g/10 min and NOT greater 
      than 1.75g/10 min, complying with American Society for
      Testing and Materials standard D 1238 (ASTM D 1238), 
      190 degrees Celsius /2.16 kg;
  (b) environmental stress-cracking of ethylene plastics failure 
      NOT less than 50% /350 hours, complying with 
      American Society for Testing and Materials standard 
      D1693-B (ASTM D1693-B);
  (c) full-notch creep test value NOT less than 30 hours
      complying with International Organization for
      Standardization 16770 (ISO 16770)

RESINS, high density polyethylene, specific gravity NOT less 
than 0.941 and NOT greater than 0.948, silane grafted, cross-
linkable

ETHYLENE VINYL ACETATE COPOLYMER, having ALL of the following:
   (a) vinyl acetate content of 12.5% or greater but NOT exceeding
       15.5%;
   (b) melt index of 0.75g/10 minutes or greater but NOT exceeding
       3.5g/10 minutes calculated in accordance with ASTM D1238/70;
   (c) density of 0.92 grams/cu cm or greater but NOT exceeding
       0.94 g/cu cm

ETHYLENE VINYL ACETATE COPOLYMER, with vinyl acetate content
 between 10.7% - 13.3% (both inclusive), and melt flow index
 between 2-3 g/10 min (both inclusive)

ETHYLENE VINYL ACETATE COPOLYMER, in solid form, having ALL of
 the following:
   (a) a vinyl acetate content of 15% by weight or greater but NOT
       exceeding 28%;
   (b) a melt flow index of a minimum of 10 g/10 min, but NOT
       exceeding 100 g/10 min, calculated in accordance with
       ASTM D 1238

ETHYLENE VINYL ACETATE COPOLYMER, in solid form, having a vinyl
 acetate content of 27% or greater but NOT exceeding 40% and a
 melt flow index of 30 g/10 min or greater but NOT exceeding
 420 g/10 min calculated in accordance with ASTM D 1238 Condition E
 (Load 2.16 kg, Temperature 190 degrees C) units g/10 min

ETHYLENE VINYL ACETATE COPOLYMER, in solid form, having ALL of the
 following:
   (a) a vinyl acetate content of 17% by weight or greater but NOT
       exceeding 19%;
   (b) a melt flow index of a minimum of 0.75g/10min but NOT
       exceeding 600g/10min calculated in accordance with ASTM D1238

ETHYLENE-VINYL ACETATE COPOLYMER RESIN, in pellet form, having ALL
 of the following:
   (a) a vinyl acetate content by weight of 11.0% or greater but NOT
       exceeding 12.5%;
   (b) a melt index of 0.25 dg/min or greater but NOT exceeding
       0.45 dg/min calculated in accordance with ASTM D-1238;
   (c) a density of 0.92 gms/cc or greater but NOT exceeding
       0.94 gms/cc calculated in accordance with ASTM D-792

ETHYLENE VINYL ACETATE CO-POLYMER, having a vinyl acetate content
 within the range 24.7% to 29.3%, (inclusive), and a melt flow
 index within the range 2.2 to 3.8 g/10min (inclusive)

ETHYLENE VINYL ACETATE COPOLYMER, in solid form, having ALL of the
 following:
   (a) a vinyl acetate content of 15% by weight or greater but NOT
       exceeding 28%;
   (b) a melt flow index of a minimum of 0.75g/10min but NOT
       exceeding 10g/10min calculated in accordance with ASTM D1238

ETHYLENE VINYL ACETATE COPOLYMERS, having BOTH of the 
following:    
  (a) a melt flow index rate of not less than 4g/10 min in     
      accordance with ISO 1133;                                  
  (b) a flammability temperature index of not less than 260 
      degrees celsius in accordance with ISO 4589-3

ETHYLENE VINYL ACETATE COPOLYMER, in solid form (granules)

RESINS, LINEAR LOW DENSITY POLYETHYLENE (LLDPE), having ALL of 
the following:
  (a) melt flow rate (MFR) (at 190 degrees Celsius and 2.16kg) 
      NOT less than 15 g/10 minute and NOT greater than 55 g/10
      minute, complying with American  Society for Testing and
      Materials standard ASTM D1238 (D1238);
  (b) density NOT less than 0.92 kg/m3 and not greater than 
      0.93 kg/m3, complying with American Society for Testing
      and Materials standard ASTM D1505 (D1505);
  (c) Vicat softening temperature NOT less than 80 degrees 
      Celsius and NOT greater than 105 degrees Celsius,  
      complying with American Society for Testing and Material
      standard ASTM D1525 (D1525)

RESINS, LINEAR LOW DENSITY POLYETHYLENE (LLDPE), having ALL of 
the following:
(a) density NOT less than 905 kg/m3 and NOT greater than 935  
    kg/m3, complying with ANY of the following standards:
          (i) American Society for Testing and Materials 
              standard D1505 (ASTM D1505);
          (ii) American Society for Testing and Materials 
               standard D792 (ASTM D792);
         (iii) International Organisation for Standardisation 
               standard 1183 (ISO 1183)
  (b) melt flow rate (MFR) (at 190 degrees Celsius and 2.16 kg) 
      NOT less than 5.0 g/10 minute and NOT greater than 65.0 
      g/10 minute, complying with EITHER of the following 
      standards:
         (i) American Society for Testing and Materials standard 
             D1238 (ASTM D1238);
        (ii) International Organisation for Standardisation 
             standard 1133 (ISO 1133)

RESINS, LINEAR LOW DENSITY POLYETHYLENE (LLDPE), having BOTH of 
the following:
  (a) density NOT less than 905 kg/m3 and NOT greater than 935 
      kg/m3, complying with ANY of the following standards:
          (i) American Society for Testing and Materials     
              Standard D1505 (ASTM D1505);
         (ii) American Society for Testing and Materials         
              Standard D792 (ASTM D792);
        (iii) International Organisation for Standardisation 
              Standard 1183 (ISO 1183), 
  (b) melt flow rate (MFR) at 190 degrees Celsius and 2.16 kg,  
      NOT less than 0.5 g/10 minute and NOT greater than 5.0g/10 
      minute, complying with EITHER of the following standards: 
          (i) American Society for Testing and  Materials     
              Standard D1238 (ASTM D1238); 
         (ii) International  Organisation for Standardisation 
              Standard 1133 (ISO 1133)

RESINS, being unpigmented bimodal terpolymer polyethylene, in 
pelletised form, having ALL of the following:
  (a) melt flow rate NOT less than 1.2 g/10 min and NOT greater
      than 1.8 g/10 min, complying with American Society for 
      Testing and Materials standard D 1238 (ASTM D 1238), 190 
      degrees Celsius/2.16 kg;
  (b) density NOT less than 915 kg/m3 and NOT greater than 
      920 kg/m3, complying with American Society for Testing and 
      Materials standard D 792 (ASTM D 792);
  (c) vicat softening point NOT less than 100 degrees Celsius
      and NOT greater than 104 degrees Celsius, complying with 
      American Society for Testing and Materials standard D 1525
      (ASTM D 1525)

RESINS, being unpigmented bimodal polyethylene, in pelletised 
form, having ALL of the following:
  (a) melt flow rate NOT less than 0.45 g/10 min and NOT greater
      than 0.75 g/10 min, complying with American Society for 
      Testing and Materials standard D 1238 (ASTM D 1238), 190 
      degrees Celsius/5.0 kg;
  (b) density NOT less than 932 kg/m3 and NOT greater than 
      938 kg/m3, complying with American Society for Testing and 
      Materials standard D 792 (ASTM D 792);
  (c) vicat softening point NOT less than 126 degrees Celsius
      and NOT greater than 130 degrees Celsius, complying with 
      American Society for Testing and Materials standard D 1525 
      (ASTM D 1525);
  (d) environmental stress-cracking of ethylene plastics failure 
      NOT less than 50 per cent/5 000 hours, complying with 
      American Society for Testing and Materials standard 
      D 1693-B (ASTM D 1693-B)

RESINS, being unpigmented bimodal terpolymer polyethylene, in 
pelletised form, having ALL of the following:
  (a) melt flow rate NOT less than 1.0 g/10 min and NOT greater 
      than 1.6 g/10 min, complying with American Society for
      Testing and Materials standard D 1238 (ASTM D 1238), 190 
      degrees Celsius/2.16kg;
  (b) density NOT less than 925 kg/m3 and NOT greater than 
      930 kg/m3, complying with American Society for Testing and 
      Materials standard D 792 (ASTM D 792);
  (c) vicat softening point NOT less than 114 degrees Celsius
      and NOT greater than 118 degrees Celsius, complying with 
      American Society for Testing and Materials standard D 1525 
      (ASTM D 1525)

RESINS, being unpigmented enhanced ethylene alpha olefins 
copolymer polyethylene, in pelletised form, having ALL of the 
following:
  (a) melt flow rate NOT less than 0.5 g/10 min and NOT greater
      than 0.9 g/10 min, complying with American Society for 
      Testing and Materials standard D  1238 (ASTM D 1238), 190 
      degrees Celsius/5.0 kg;
  (b) density NOT less than 919 kg/m3 and NOT greater than 923
      kg/m3, complying with American Society for Testing and 
      Materials standard D 792 (ASTM D 792);
  (c) vicat softening point NOT less than 121 degrees Celsius
      and NOT greater than 125 degrees Celsius, complying with 
      American Society for Testing and Materials standard D 1525 
      (ASTM D 1525);
  (d) environmental stress-cracking of ethylene plastics failure 
      NOT less than 50 per cent/5 000 hours, complying with 
      American Society for Testing and Materials standard 
      D 1693-B (ASTM D 1693-B)

RESINS, being unpigmented bimodal polyethylene, in pelletised 
form, having ALL of the following:
  (a) melt flow rate NOT less than 0.80 g/10 min and NOT greater
      than 1.10 g/10 min, complying with American Society for
      Testing and Materials standard D 1238 (ASTM D1283), 190 
      degrees Celsius/5.0 kg;  
  (b) density NOT less than 920 kg/m3 and NOT greater than 925
      kg/m3, complying with American Society for Testing and 
      Materials standard D 792 (ASTM D 792;  
  (c) vicat softening point NOT less than 126 degrees Celsius
      and NOT greater than 128 degrees Celsius, complying with 
      American Society for Testing and Materials standard 
      D 1525 (ASTM D 1525); 
  (d) environmental stress-cracking of ethylene plastics failure 
      NOT less than 50 per cent/5 000 hours, complying with 
      American Society for Testing and Materials standard 
      D 1693-B (ASTM D 1693-B)

POLYOLEFIN COPOLYMER conforming to AS3147-1988 of the type
 HFI-75-TP and/or HFI-90-TP having characteristics of low smoke
 emission and low flame propagation properties in fire conditions

POLYETHYLENE COPOLYMER, maleic anhydride grafted, having a melt
 flow index of LESS than 9 g/10 min calculated in accordance with
 ASTM D1238

POLYETHYLENE, chlorinated, having a chlorine content of 22% or
 greater but NOT exceeding 45% (by weight), containing NOT less than
 95% chlorinated polyethylene

ELASTOMERS, chlorosulphonated polyethylene

ETHYLENE-ACRYLIC ACID COPOLYMERS, in solid form, having a melt
 index NOT exceeding 200 g/10 min (ASTM D 1238, Condition E) and
 a reacted acrylic acid monomer content NOT exceeding 16% w/w
 (ASTM D 4094)

POLYETHYLENE RESINS, chlorosulphonated

ETHYLENE-METHACRYLIC ACID COPOLYMERS or their salts

ETHYLENE-METHYL ACRYLATE COPOLYMERS, in solid form, having a
 reacted methyl acrylate content of 15% or greater but NOT
 exceeding 50%

POLYETHYLENE COPOLYMER COMPOUND, silane crosslinkable,
 semi-conductive

RESINS, being unpigmented butyl acrylate-ethylene copolymer, in 
pelletised form, having ALL of the following:
  (a) melt flow rate NOT less than 0.2 g/10 min and NOT greater 
      than 2 g/10 min complying with International Standard 
      ISO 1133-1:2011(E), at 190 degrees Celsius/2.16 kg;
  (b) density NOT less than 920 kg/m3 and NOT greater than 
      930 kg/m3 complying with International Standard  
      ISO 1183-1:2012(E), at 23 degrees Celsius;
  (c) tensile modulus NOT less than 20 MPa and NOT greater than 
      200 MPa in accordance with International Standard    
      ISO 527-1:2012(E), at 23 degrees Celsius;
  (d) n-butyl acrylate concentration NOT less than 5.5% and NOT 
      greater than 7.5%

POLYETHYLENE COPOLYMER, crosslinkable, halogen free, having ALL 
of the following:
  (a) specific gravity NOT less than 1.35 gms per cm3 and NOT
      greater than 1.45 gms per cm3;
  (b) oxygen index NOT less than 28 and NOT greater than 34 
      complying with American Society for Testing  Materials 
      D 2863 (ASTM D 2863);
  (c) melt mass flow rate NOT greater than 11 grams per 10 mins 
      complying with American Society for Testing Materials  
      D 1238 (ASTM D 1238)

TERPOLYMERS OF ETHYLENE, ACRYLIC ESTER AND MALEIC ANHYDRIDE

ATACTIC POLYPROPYLENE RESINS

RESINS, ISOTATIC POLYPROPYLENE, MEDICAL GRADE, in accordance 
with International Organisation for  Standardisation 10993 (ISO 
10993)

POLYPROPYLENE MALEIC ANHYDRIDE COPOLYMERS, being adhesion polymers

POLYPROPYLENE, randomly copolymerised with ethylene and/or
 butylene, with a vicat softening point between 85 degrees C
 and 125 degrees C

ETHYLENE-PROPYLENE RUBBERS (EPR or EPM)

RESINS, unpigmented polypropylene copolymer, propylene based 
with comonomer ethylene, having ALL of the following 
  (a) pelletised form; 
  (b) ethylene monomer composition by weight NOT less than 7% 
      and NOT greater than 9%; 
  (c) melt mass-flow rate (at 230 degrees Celsius) with a mass 
      of 2.16 kg NOT less than 30g/10 min and NOT greater than
      55 g/10 min complying with International Organization for
      Standardization standard ISO 1133 (ISO 1133);
  (d) density (at 23 degrees Celsius) NOT less than 890 kg/m3 
      and NOT greater than 910 kg/m3 complying with  
      International Organization for Standardization standard  
      ISO 1183 (ISO 1183); 
  (e) softening temperature NOT less than 140 degrees Celsius 
      and NOT greater than 155 degrees Celsius complying with
      method A50 of International Organization for
     Standardization standard ISO 306 (ISO 306)

RESIN, being unpigmented polypropylene heterophasic copolymer, 
propylene based with comonomer ethylene, in pelletised form, 
having ALL of the following:
  (a) ethylene monomer composition by weight NOT less than 8.5%
      and NOT greater than 10%;
  (b) melt flow rate not less than 4 g/10 min and NOT greater 
      than 6 g/10 min complying with International Standard 
      ISO1133;
  (c) density NOT less than 890 kg/m3 and NOT greater than 
      910 kg/m3 complying with International Standard ISO1183

RESIN, being unpigmented polypropylene heterophasic copolymer, 
propylene based with comonomer ethylene, in pelletised form, 
having ALL of the following:
  (a) ethylene monomer composition by weight NOT less than 8.0%
      and NOT greater than 11.0%;
  (b) melt flow rate NOT less than 14 g/10 min and NOT greater
      than 18 g/10 min complying with International Standard 
      ISO1133;
  (c) density NOT less than 890 kg/m3 and NOT greater than 
      910 kg/m3 complying with International Standard ISO1183;
  (d) tensile modulus NOT less than 1 300 MPa and NOT greater
      than 1 700 MPa complying with International Standard ISO527

RESINS, being unpigmented polypropylene heterophasic copolymer, 
propylene based with comonomer ethylene, in pelletised form, 
having ALL of the following:
  (a) ethylene monomer composition by weight NOT less than 9% 
      and NOT greater than 11%;
  (b) melt flow rate NOT less than 6 g/10 min and NOT greater 
      than 9 g/10 min in accordance with international standard 
      ISO 1133, 230 degrees celsius / 2.16 kg;
  (c) density NOT less than 900 kg/m3 and NOT greater than 
      910 kg/m3 in accordance with international standard 
      ISO 1183;

RESINS, being unpigmented polypropylene heterophasic copolymer, 
propylene based, in pelletised form, having ALL of the following:
  (a) ethylene monomer composition by weight NOT less the 8.5% 
      and NOT greater than 11.5%;
  (b) melt flow rate NOT less than 9 g/10 min and NOT greater 
      than 15 g/10 min tested in accordance with International 
      Standard ISO 1133-1:2011(E) at 230 degrees Celsius/2.16 kg;
  (c) density NOT less than 900 kg per cubic metre and NOT 
      greater than 910 kg per cubic metre tested in accordance 
      with International Standard ISO 1183-1:2004(E);
  (d) tensile modulus (1 mm/min) NOT less than 1 100 MPa and NOT
      greater than 1 300 MPa tested in accordance with     
      International Standard ISO 527-1:2012(E)

RESINS, being unpigmented polypropylene heterophasic copolymer, 
propylene based, in pelletised form, having ALL of the following:
  (a) ethylene monomer composition by weight NOT less the 5% and
      NOT greater than 6%;
  (b) melt flow rate NOT less than 6 g/10 min and NOT greater 
      than 8.5 g/10 min tested in accordance with International 
      Standard ISO 1133-1:2011(E) at 230 degrees Celsius/2.16 kg;
  (c) density NOT less than 900 kg per cubic metre and NOT 
      greater than 910 kg per cubic metre tested in accordance 
      with International Standard ISO 1183-1:2004(E);
  (d) tensile modulus (1 mm/min) NOT less than 1 400 MPa and NOT
      greater than 1 600 MPa tested in accordance with     
      International Standard ISO 527-1:2012(E)

RESINS, ETHYLENE POLYPROPYLENE COPOLYMER, in pelletised form, 
having ALL of the following:
  (a) ethylene monomer composition NOT less than 8.5% and NOT 
      greater than 12.0%;
  (b) melt flow rate NOT less than 24 g/10min and NOT greater 
      than 36 g/10min, complying with ASTM International  
      Standard D1238;
  (c) density NOT less than 0.890 g/cm3 and NOT greater than 
      0.910 g/cm3, complying with ASTM International Standard  
      D792;
  (d) vicat softening temperature NOT less than 140 degrees 
      Celsius and NOT greater than 155 degrees Celsius,  
      complying with ASTM International Standard D1525;

RESINS, being unpigmented ethylene-propylene copolymer, in 
pelletised form, having ALL of the following:
  (a) melt flow rate NOT less than 0.5 g/10 min and NOT greater 
      than 5 g/10 min complying with International Standard 
      ISO 1133-1:2011(E), at 230 degrees Celsius/2.16 kg;
  (b) density NOT less than 870 kg/m3 and NOT greater than 
      900 kg/m3 complying with International Standard  
      ISO 1183-1:2012(E), at 23 degrees Celsius;
  (c) tensile modulus NOT less than 600 MPa and NOT greater than 
      1 000 MPa complying with International Standard     
      ISO 178:2010(E), at 23 degrees Celsius

RESINS, being unpigmented ethylene-propylene copolymer, in 
pelletised form, having ALL of the following:
  (a) melt flow rate NOT less than 5 g/10 min and NOT greater
      than 50 g/10 min complying with International Standard  
      ISO 1133-1:2011(E), at 23 degrees Celsius/2.16 kg;
  (b) density NOT less than 870 kg/m3 and NOT greater than 
      900 kg/m3 complying with International Standard  
      ISO 1183-1:2012(E), at 23 degrees Celsius;
  (c) flexural modulus NOT less than 20 MPa and NOT greater than 
      200 MPa complying with International Standard    
      ISO 178:2010(E), at 23 degrees Celsius

RESINS, being unpigmented ethylene-propylene, in pelletised 
form, having ALL of the following:
  (a) melt flow rate NOT less than 0.5 g/10 min and NOT greater 
      than 5 g/10 min complying with International Standard 
      ISO 1133-1:2011(E), at 230 degrees Celsius/2.16 kg;
  (b) density NOT less than 870 kg/m3 and NOT greater than 900 
      kg/m3 complying with International Standard 
      ISO 1183-1:2012(E), at 23 degrees Celsius;
  (c) flexural modulus NOT less than 20 MPa and NOT greater
      than 400 MPa complying with International Standard
      ISO 178:2010(E), at 23 degrees Celsius

POLYPROPYLENE HETEROPHASIC COPOLYMER RESIN, being propylene 
based with comonomer ethylene, unpigmented, pelletised, having 
ALL of the following:
  (a) ethylene monomer composition by weight NOT less than 8.5% 
      and NOT greater than 10.5%;
  (b) melt flow rate NOT less than 16g/10min and NOT greater 
      than 24g/10 min in accordance with International Standard  
      1133 (ISO1133) at 230 degrees Celsius/2.16 kg;
  (c) density NOT less than 890 kg/m3 and NOT greater than 910 
      kg/m3 in accordance with International Standard 1183 
      (ISO1183) at 23 degrees Celsius;
  (d) flexural modulus NOT less than 1 350 MPa and NOT greater 
      than 1 550 MPa in accordance with International Standard 
      178 (ISO178) at 23 degrees Celsius

RESINS, being unpigmented polypropylene heterophasic copolymer, 
propylene based with comonomer ethylene, in pelletised form, 
having ALL of the following:
  (a) ethylene monomer composition by weight NOT less than 
      7% and NOT greater than 9%;
  (b) melt mass-flow rate (at 230 degrees Celsius with a mass of
      2.16 kg) NOT less than 38 g/10 min and NOT greater
      than 50 g/10 min complying with International Organization
      for Standardization standard ISO 1133-1:2011(E);
  (c) density (at 23 degrees Celsius) NOT less than 890 kg/m3 and
      NOT greater than 910 kg/m3 in accordance with
      International Organization for Standardization 
      standard ISO 1183-1:2012(E); 
  (d) tensile modulus (at 23 degrees Celsius) NOT less than 
      1 450 MPa and NOT greater than 1 650 MPa complying with
      International Organization for Standardization standard 
      ISO 527-1:2012(E)

RESINS, being unpigmented polypropylene heterophasic copolymer, 
propylene based with comonomer ethylene, in pelletised form, 
having ALL of the following:
  (a) ethylene monomer composition by weight NOT less than 7% 
      and NOT greater than 9%;
  (b) melt mass-flow rate (at 230 degrees Celsius with a mass of
      2.16 kg) NOT less than 6 g/10 min and NOT greater
      than 8 g/10 min complying with International Organization 
      for Standardization standard ISO 1133-1:2011(E);
  (c) density (at 23 degrees Celsius) NOT less than 890 kg/m3 and
      NOT greater than 910 kg/m3 complying with International
      Organization for Standardization standard
      ISO 1183-1:2012(E); 
  (d) softening temperature NOT less than 140 degrees Celsius
      and NOT greater than 155 degrees Celsius complying
      with method A50 of International Organization for
      Standardization standard ISO 306:2013(E)

RESINS, being unpigmented polypropylene heterophasic copolymer, 
propylene based with comonomer ethylene, in pelletised form, 
having ALL of the following:
  (a) ethylene monomer composition by weight NOT less than 7% 
      and NOT greater than 10%;
  (b) melt mass-flow rate (at 230 degrees Celsius with a mass of 
      2.16 kg) NOT less than 16 g/10 min and NOT greater
      than 24 g/10 min complying with International Organization
      for Standardization standard 1133-1:2011(E);
  (c) density (at 23 degrees Celsius) NOT less than 890 kg/m3 and
      NOT greater than 910 kg/m3 complying with International
      Organization for Standardization standard 
      ISO 1183-1:2012(E); 
  (d) tensile modulus (at 23 degrees Celsius) NOT less than 
      1 450 MPa and NOT greater than 1 650 MPa complying with 
      International Organization for Standardization standard
      ISO 527-1:2012(E)

RESINS, being unpigmented polypropylene heterophasic copolymer, 
propylene based with comonomer ethylene, in pelletised form, 
having ALL of the following:
  (a) ethylene monomer composition by weight NOT less than 8.5% 
      and NOT greater than 10.5%;
  (b) melt flow rate NOT less than 14 g/10 min and NOT
      greater than 18 g/10 min in accordance with International
      Standard 1133 (ISO 1133, 230 degrees Celsius/2.16 kg);
  (c) density NOT less than 890 kg/m3 and NOT greater than 
      910 kg/m3  in accordance with International Standard
      1183 (ISO 1183, 23 degrees Celsius);
  (d) tensile modulus NOT less than 1 450 MPa and NOT greater 
      than 1 650 MPa  in accordance with International Standard
      527 (ISO 527, 23 degrees Celsius)

RESINS, being unpigmented polypropylene heterophasic copolymer, 
propylene based with comonomer ethylene, in pelletised form, 
having ALL of the following: 
  (a) ethylene monomer composition by weight NOT less than 7%
      and NOT greater than 9%;
  (b) melt flow rate NOT less than 65 g/10 min and NOT greater
      than 75 g/10 min in accordance with International Standard
      1133 (ISO 1133, 230 degrees Celsius/2.16 kg);
  (c) density NOT less  than 890 kg/m3 and NOT greater than 910
      kg/m3 in accordance with International Standard 1183
      (ISO 1183, 23 degrees Celsius)

POWDERS, COATING, THERMOPLASTIC having a basis of propylene 
copolymer AND ethylene copolymer

PROPYLENE, randomly copolymerised with butene

POLYALPHAOLEFINS, highly branched isoparaffinic, manufactured from
 monomer units which have a carbon chain length greater than six

METHACRYLATE BUTADIENE STYRENE COPOLYMERS, having ALL of the
 following:
   (a) maximum particle size 700 microns;
   (b) minimum butadiene content 45%;
   (c) containing no acrylonitrile;
   (d) 75% minimum transparency at thickness of 3.0 mm

THERMOPLASTIC SYNTHETIC RUBBER, being styrene-ethylene-butylene-
 styrene (YSEB)

CHLORINATED RUBBER

POLYBUTENE RESINS

POLYPROPYLENE RESINS, chlorinated

PVC IMPACT MODIFIERS

EXPANDABLE POLYSTYRENE (EPS), granular bead

SPECIMEN SPHERES, polystyrene, being reference standards for
 comparative analytical practices, certified as to their chemical
 composition or other characteristics to a stated degree of
 accuracy or level of confidence

STYRENIC COPOLYMER RESIN, having ALL of the following:
  (a) styrene-acrylonitrile copolymer (NOT less than 30% - NOT
      greater than 50%);
  (b) butyl acrylate-styrene-acrylonitrile copolymer (NOT less
      than 20% - NOT greater than 40%);
  (c) acrylonitrile-alpha methylstyrene copolymer (NOT less than
      10% - NOT greater than 30%);
  (d) carbon black (NOT greater than 5%)

RESINS, STYRENIC COPOLYMER, having ALL of the following: 
  (a) NOT less than 50% and NOT greater than 70% styrene-
      acrylonitrile copolymer;
  (b) NOT less than 20% and NOT greater than 40% butyl acrylate-
      styrene-acrylonitrile copolymer;
  (c) NOT less than 1% and NOT greater than 5% titanium dioxide;
  (d) NOT less than 1% and NOT greater than 5% carbon black

STYRENIC COPOLYMER RESIN, having ALL of the following:
  (a) styrene-acrylonitrile copolymer (NOT less than 30% - NOT
      greater than 50%);
  (b) butyl acrylate-styrene-acrylonitrile copolymer (NOT less
      than 20% - NOT greater than 40%);
  (c) acrylonitrile-alpha methylstyrene copolymer (NOT less than
      10% - NOT greater than 30%);
  (d) carbon black (NOT greater than 5%)

COPOLYMERS, STYRENE-ACRYLONITRILE, granules

RESINS, acrylonitrile butadiene styrene, having ALL of the 
following:
  (a) density NOT less than 1 000 kg/m3, complying with  
      American Society for Testing and Materials ASTM D 792
      (ASTM D792); 
  (b) melt flow rate NOT less than 15 g/10min and NOT greater
      than 20 g/10min, complying with British Standard BS EN
      1133:2005(BS EN 1133:2005);
  (c) vicat softening temperature NOT greater than 100
      degrees Celsius, complying with International Organization
      for Standardization ISO 306 (ISO 306)

COPOLYMERS, MODIFIED STYRENE ACRYLIC RESIN, having non-volatile 
materials content NOT less than 97%

COPOLYMERS, having an active ingredient of NOT less than 58% 
methylstyrene acrylate

PASTE MAKING RESINS, in powder form, with aggregates of primary
 particles having an average dia NOT greater than 50 microns

POLYVINYL CHLORIDE, having ALL of the following:
(a) mean granular size NOT less than 100 microns and NOT greater
    than 200 microns; 
(b) granular size minimum 95% by volume NOT less than 50 microns
    and NOT greater than 300 microns; 
(c) K-value complying with ISO 1628-2: 1998 of NOT less than 59
    and NOT greater than 80

COPOLYMERS OF THE VINYL CHLORIDE-VINYL ACETATE TYPE, containing NOT
 less than 10% by weight of vinyl acetate groups, but NOT including
 compounded products

VINYL CHLORIDE AND VINYL ACETATE COPOLYMER RESINS, with OR 
without ANY of the following:
  (a) hydroxyl function polymers;
  (b) maleic acid;
  (c) vinyl alcohol

RESINS, POLYVINYL CHLORIDE, powder, having copolymers 
of vinyl chloride AND vinyl acetate

VINYL CHLORIDE-ISOBUTYL ETHER COPOLYMERS, having ALL of the
 following:
   (a) a dynamic viscosity at 20 degrees C, as a 20% solution in
       toluene, between 15-70 mPa.s;
   (b) a density, at 20 degrees C of approx. 1.24- approx. 1.25 g/cc

BLENDS, containing polyvinyl chloride and an ethylene terpolymer,
 having ALL of the following characteristics:
   (a) a thermoplastic elastomer;
   (b) melt processible;
   (c) 14% or more by weight of ethylene, butyl acrylate, carbon
       monoxide terpolymer

VINYL CHLORIDE AND VINYL ACETATE COPOLYMER RESINS, with OR 
without ANY of the following:
  (a) hydroxyl function polymers;
  (b) maleic acid;
  (c) vinyl alcohol

VINYLIDENE CHLORIDE POLYMERS

POLYTETRAFLUOROETHYLENE, in EITHER of the following forms:
   (a) dispersion;
   (b) unfilled granules OR powders

ETHYLENECHLOROTETRAFLUOROETHYLENE FLUOROPOLYMER, being a 1:1
 alternating copolymer of ethylene and chlorotrifluoroethylene

ELASTOMERS, comprising copolymers of tetrafluoroethylene and
 propylene

VINYLIDENE FLUORIDE POLYMERS

FLUORO-POLYMERS, being ANY of the following:
   (a) fluorinated ethylene propylene (FEP);
   (b) perfluoroalkoxy fluorocarbon (PFA);
   (c) ethylene tetrafluoroethylene (EFTE)

POLYMERS OF VINYL ACETATE, powder, capable of dispersion in water,
 with a nominal maximum particle size not exceeding 300 mu

EMULSIONS, VINYL ACETATE-ETHYLENE

EMULSIONS, vinyl acetate-ethylene

ETHYLENE VINYL ACETATE COPOLYMER/TERPOLYMER AQUEOUS DISPERSIONS, 
having ALL the following:
  (a) non volatile matter (solids) content NOT less than 50% and
      NOT greater than 72%;
  (b) stabilized by polyvinyl alcohol, cellulosics, surfactants 
      or combinations thereof;
  (c) glass transition temperature (Tg) NOT less than minus
      40 degrees C and NOT greater than plus 10 degrees C

VINYL ACETATE - VINYL PYRROLIDONE COPOLYMER PRIMARY FORMS,
 containing NOT less than 25% w/w reacted vinyl pyrrolidone

ETHYLENE VINYL ALCOHOL COPOLYMERS

POLYVINYL ALCOHOL, being hydrolysed polyvinyl acetate with a
 degree of hydrolysis of NOT less than 45%

RESINS, being terpolymers of vinyl acetate, crotonic acid and
 vinyl propionate

VINYL PYRROLIDONE-STYRENE COPOLYMERS, containing NOT less than 25%
 reacted vinyl pyrrolidone, put up in emulsion form

POLYVINYL PYRROLIDONE POLYMERS AND COPOLYMERS

RESINS, being copolymers of polyvinyl ether incorporating A 
antigens OR B antigens

METHYL VINYL ETHER POLYMERISATION PRODUCTS, being ANY of the
 following:
   (a) methyl vinyl ether homopolymer;
   (b) methyl vinyl ether/maleic acid copolymer;
   (c) methyl vinyl ether/maleic anhydride copolymers and esters
       thereof

POLYVINYL PYRROLIDONE POLYMERS AND COPOLYMERS

POLYVINYL BUTYRAL

POLYVINYLAMINES

ACRYLIC POLYMERS OR COPOLYMERS, prosthetic, in packs NOT
 exceeding 10 kg

ACRYLIC POLYMERS OR COPOLYMERS, dental, put up for sale in packs
 NOT exceeding 20 kg

ACRYLIC POLYMERS, containing no reacted monomers OTHER THAN
 acrylic monomers, being polyvinyl chloride processing aids in
 powder form with a particle size of less than 600 microns

POLYMETHYL METHACRYLATE RESIN in the form of pellets exhibiting a
 melt flow index of 3.5 g/10 mins or less when tested to ASTM D1238,
 condition 1 or by DIN53735

POLYMETHYL METHACRYLATE, in granular form, having ALL of the
 following listed in EITHER Table A OR Table B:
         Table A
   (a) clear, with NO less than 55% luminous transmittance when
       measured by ASTM D-1003 on samples of 0.060 inch thickness
       and using light source A or by DIN 5036;
   (b) NO greater than 4.0 g/10 min melt flow index when measured
       by ASTM D-1238 condition I or by DIN 53735
         Table B
   coloured red or amber with a luminous transmittance NOT less than
   15% and NOT greater than 85% when measured by ASTM D-1003 on
   samples of 0.060 inch thickness and using light source A or by
   DIN 5036

RESINS, POLYMETHYL METHACRYLATE, in pellet form

POLYMETHYLMETHACRYLATE (PMMA), in powder OR bead form, with OR 
without adipic acid, having a mean particle diameter NOT greater 
than 160 microns

ACRYLIC POLYMERS, having ALL of the following:
   (a) particle size NOT more than 1 000 microns;
   (b) butyl acrylate content NOT less than 64%;
   (c) transparency NOT more than 75%;
   (d) notched izod impact NOT less than 20 ft - lbs/in.
       under ASTM - D256

SUPER ABSORBENT POLYMERS (SAP), based on acrylic resins, in solid
 form, capable of absorbing 25 times or more their own weight in
 water

ELASTOMERS, ethylene/acrylic, being copolymers of ethylene and
 methyl acrylate

METHYL METHACRYLATE - ALKYL METHACRYLATE COPOLYMER, in solid form

ACRYLIC RESIN KITS, having laboratory tissue sample embedding
 applications

ACRYLIC POLYMER, absorbed on silicone dioxide in white powder form,
 containing NOT less than 67% acrylic polymer

ACRYLIC-STYRENE COPOLYMERS, powder form, with a particle size of
 LESS than 600 microns

BUTYL ACRYLATE AND STYRENE COPOLYMERS in powder form NOT containing
 ANY of the following:
   (a) plasticers;
   (b) film forming agents;
   (c) inorganic fillers

ACRYLATES, C10-30 ALKYL ACRYLATE CROSSPOLYMER, in powder form

POLYACRYLIC ACID, crosslinked with polyalkenyl polyether,
 powder form

COPOLYMER, liquid form, having a composition of NOT less than 
35% Acrylamide - Acrylic Acid Copolymer, Sodium Salt

DRILLING FLUID ADDITIVE, VISCOSIFIER, powder OR granule form

SHALE INHIBITING AGENT, ACRYLIC POLYMER AND/OR CO-POLYMER, 
having ALL of the following:
  (a) acrylic acid content NOT less than 10%;
  (b) 2-hydroxypropyl acrylate content NOT less than 10%;
  (c) in powder AND/OR granules

ACRYLIC POLYMERS, absorbent, in granular OR powder form, based 
on acrylic resin AND starch

FLOOD MITIGATION BAGS, needle punched polypropylene filled 
with absorbent paper embedded with sodium polyacrylate granules

KITS, BATHING WATER POWDER ADDITIVE, with OR without perfume OR 
colour agent, having BOTH of the following:
  (a) sodium polyacrylate;
  (b) sodium chloride

STYRENE ACRYLATE POLYMERS, in powder or granule form

EMULSIONS, ACRYLIC HYBRID COPOLYMER, with fluropolymer AND/OR 
alkyd, having BOTH of the following:
 (a) solids NOT greater than 46%;
 (b) minimum film forming temperature (MFFT) NOT greater than 
     5 degrees C

RESIN, ACRYLIC POLYMER, ultra violet curable

METHOXY POLYETHYLENE GLYCOL, solid form

POLYALKYLENE GLYCOL

PERFLUORINATED POLYETHER FLUIDS

POLYPROPYLENE GLYCOL 14 BUTYL ETHER

POLYOXYPROPYLENE DIAMINE

POLYTETRAMETHYLENE ETHER GLYCOL

STABILIZERS, light, hindered amine, polymeric

POLYHYDROXYETHER POLYOL PRIMARY FORMS, grafted with ANY of the
 following:
   (a) acrylonitrile or polyacrylonitrile;
   (b) acrylonitrile and styrene;
   (c) methylmethacrylate,
 and containing NOT less than 20% reacted acrylonitrile,
 acrylonitrile and styrene combined or methylmethacrylate

MERCAPTAN TERMINATED POLYETHER POLYOL

ETHYLENE OXIDE POLYMERS, having a molecular weight exceeding
 20 000

ACRYLONITRILE-STYRENE COPOLYMER, grafted, dispersed in polyether 
polyol

POLYETHER POLYOL, PRIMARY FORM

POLYPROPYLENE GLYCOL MONOMETHACRYLATE

HEAT PADS, ANIMAL WARMTH, microwavable, incorporating polyether 
resins

RESINS, silyl-terminated polyether

LIQUID RESIN, based on the polymerisation of epichlorohydrin and
 4.4 methylenediphenol

EPOXY NOVOLAC RESIN, being a reaction product of epichlorhydrin,
 phenol and formaldehyde, with a functionality exceeding 2

POLYMER PROTECTIVE FINISH, durable clear finish epoxy resin and
 hardener for all surfaces

LIQUID EPOXY RESIN, manufactured from epichlorohydrin and 4.4
isopropylidene diphenol with an epoxide equivalent weight less 
than 210

LIQUID EPOXY RESIN, being a mixture of products based on the 
polymerisation of epichlorohydrin and 4.4 methylene diphenol and 
products based on the polymerisation of epichlorohydrin and 
4.4 isopropylidene diphenol

LIQUID EPOXY RESINS, whether or not diluted with a solvent or 
diluent, being EITHER of the following:
  (a) having a basis of either Bisphenol-A OR Bisphenol-F;
  (b) having a basis of a mixture of Bisphenol-A AND Bisphenol-F

POWDERS, EPOXY, THERMOSETTING, having a specific gravity NOT 
less than 1.40 and NOT greater than 1.70

POWDERS, EPOXY, FUSION BONDED, having a curing time at 232 
degrees Celsius of NOT less than 30 seconds

POWDERS, EPOXY, FUSION BONDED, having an application temperature 
range of NOT less than 190 degrees celsius and NOT greater than 
230 degrees celsius

EPOXY RESIN, two part, based on bisphenol and modified
 cyclo-aliphatic polyamine

COMPOUNDED POLYCARBONATE, in primary form, having ALL of the
 following:
   (a) a density at 23 degrees C measured according to DIN 53479 of
       1.19 g/cm cu;
   (b) a melt flow index (MVI 300 degrees C, 1.2 kg) measured
       according to DIN 53735 in the range of 8.5-9.5 cm cu/10 min;
   (c) a melt viscosity (KU-internal 300 degrees C, 165 s-1) of a
       range of 460-465 Pa/S;
   (d) containing a minimum of 3.0% w/w of UV stabilizer

COMPOUNDED POLYCARBONATE, medical grade, in primary form, having 
ALL of the following:
  (a) melt volume-flow rate 330 ?C per 2.16 kg having a typical
      value of NOT less than 13 cm and NOT greater than 23 cm per
      cu3 per 10 min;
  (b) melt mass-flow rate 330 ?C per 2.16 kg having a typical
      value of NOT less than 13 cm and NOT greater than
      23.6 g per 10 min;
  (c) vicat softening temperature 50 N, 120 ?C per hour at NOT
      less than 166 degrees Celsius and NOT greater than 
      174 degrees Celsius

RESINS, alkyd, solvent form, having ALL of the following:
  (a) containing NOT less than 28% and NOT greater than 
      75% vegetable oil;
  (b) gardner-holdt viscosity range a to z5;
  (c) gardner-holdt colour range 1 to 10; 
  (d) acid value NOT greater than 10

RESINS,ALKYD, modified, having NOT less than 38% aqueos emulsion

GLYCOL MODIFIED POLYETHYLENE TEREPHTHALATE, granulated

GLYCOL MODIFIED POLYETHYLENE TEREPHTHALATE, granulated

RESINS,POLYLACTIC ACID,in pellet form

POLYESTER RESINS, unsaturated, containing no styrene, being diallyl
 phthalate prepolymers

POLYESTER ACRYLATE OLIGOMER, prepared for lithographic ink formation

POLYESTERS, polybutylene terephthalate, thermoplastic, 
granular, having ALL of the following:
  (a) viscosity number of 160 cm?/g (?15%) in phenol/1,2-
      dichlorobenzene solution (0.5% concentration), complying 
      with International Organization for    
      Standardization (ISO 1628-1:2024);
  (b) melt volume-flow rate (MVR) in the range of 6-12 cm?/10 
      min (?10%) at 250 degrees Celsius under 2.16 kg load,  
      complying with International Organization for    
      Standardization (ISO 1133-1:2022);
  (c) melting temperature of 223 degrees Celsius 
      (?5 degrees Celsius), complying with International  
      Organization for Standardization (ISO 11357-3:2025);
  (d) moisture content for processing less than 0.09%,  
      complying with International 
      Organization for Standardization (ISO 62:2008)

RESINS, polyester, high U.V. reactive, dissolved in monomers

POLYESTERS, pellet form, having a density NOT less than 1.2g/cm3

POLYESTERS, amorphous linear saturated

POLYESTER COATING POWDER, saturated polyester resin base

POLYAMIDE, in powder or granular form, being EITHER of the
 following forms:
   (a) polyamide-11;
   (b) polyamide-12

RESINS, UNFILLED POLYAMIDE 6.6, having ALL of the following:
  (a) tensile modulus of 3000/1100 MPa in dry/conditioned states;
  (b) density 1 130 kg/m3;
  (c) melt volume flow rate (MVR) of 115 cm3/10 min;
  (d) charpy notched impact strength of 5.5/20.0 kJ/m3 in
      dry/conditioned states
Tolerances of + 10% and - 10% are allowable for specifications 
(a) through to (d)

RESINS, UNFILLED POLYAMIDE 6 UNFILLED WITH NUCLEATION AGENT, 
having ALL of the following:
  (a) dry or conditioned tensile modulus 3 400/1 200 MPa;
  (b) density 1 130 kg/m3;
  (c) melt volume flow rate (MVR)175 cm3/10 minutes
Tolerances of + 5% and - 5% are allowable for specifications (a) 
through to (c)

POLYAMIDE RESIN, alcohol-soluble and reducible non-reactive

POLYAMIDE RESIN, alcohol-soluble and reducible non-reactive

POLYAMIDE, granular OR pellet, having BOTH of the following:
  (a) tensile modulus NOT less than 1 380 MPa;
  (b) melting temperature NOT less than 250 degrees Celsius

RESIN, co-polyamide, semi-aromatic, amorphous, having ALL of 
the following:
  (a) density NOT greater than 1.20 g/cm3 measured in 
      accordance with ISO 1183;
  (b) tensile E-Modulus NOT less than 2 800 MPA and NOT greater 
      than 3 200 MPa measured in accordance with ISO 527-2;
  (c) melt volume rate NOT less than 20 cm3/10 mins and 
      NOT greater than 30 cm3/10 mins measured at 275 degrees 
      C/5 Kg in accordance with ISO 1133

POLYAMIDE, in powder OR granular form, being EITHER of the 
following:
  (a) polyamide 10,10;
  (b) polyamide 10,12

POLYCONDENSATION RESIN derived from cyclised urea and aliphatic
 aldehydes, in solid form, having a softening point of
 80 - 110 degrees C

UREA RESIN POLYMER GRANULES

RESINS, UREA-FORMALDEHYDE, pre-expanded

METHOXYMETHYL MELAMINE POLYMERS

ISOCYANATES, being EITHER of the following:
  (a) polymeric methylene diphenyl isocyanate(MDI) isomers AND
      homologues;
  (b) polyol reacted compounds, comprised of NOT less than 50%
      by weight of unreacted polymeric methylene diphenyl
      isocyanate(MDI)

FRICTION DUST, being inert free flowing granular solids, with
 particle size less than 1 000 microns, being EITHER of the
 following:
   (a) cross-linked phenolic and modified phenolic based
       polymers;
   (b) aldehyde condensation product of cashew nutshell liquid

PHENOL FORMALDEHYDE, being hemispheres of solid resin in pastille
 form

RESIN, NOVOLAK PARAOCTYLPHENOL FORMALDEHYDE THERMOPLASTIC
 TACKIFYING, having ALL of the following:
   (a) pastille form;
   (b) yellow colour;
   (c) softening point in the range 85 degrees C to 95 degrees C
       (inclusive) by the ring and ball method;
   (d) residual ash of less than 0.1% after combustion

PHENOLIC RESIN, being a cresylic acid solution of phenol novolac
 resin based on a mixture of alkyl and aryl phenol

PHENOL FORMALDEHYDE RESINS, liquid form, having EITHER of the 
following;
  (a) solid content NOT less than 68% (Test Method: 120 degrees
      Celsius for 2 hours);
  (b) non-volatile components NOT less than 69% (Test Method:
      135 degrees Celsius for 2 hours)

RESIN, PHENOLIC, in powder form

PHENOL FORMALDEHYDE THERMOSET MOULDING COMPOUND, having ALL of the
 following:
   (a) granular powder form;
   (b) 35% to 60% resin;
   (c) hexamine content 5% to 10%;
   (d) specific gravity (density) 1.3 g/cu cm to 1.94 g/cu cm
       (when moulded)

POLYISOCYANATE CROSS LINKING AGENTS, produced with 0.5% or LESS
 free isocyanate monomer

THICKENER, being water soluble polyurethane, associative thickeners

THICKENERS, being hydrophobically modified ethylene oxide, urethane
 rheological modifier, polyurethane associative thickeners

THICKENERS, non ionic, being polyether, polyurethane associative
 thickeners

LAMINATING ADHESIVES, 100% non-volatiles, methyl di-isocyanate based
 polyurethane prepolymer, isocyanate or hydroxyl terminated

POLYURETHANE FOAM, expandable, two component, non-flammable, in kit
 form greater than one litre

ADHESIVES, laminating, polyurethane prepolymer solution in ethyl
 acetate

UNMIXED RESIN KITS, having BOTH of the following:
  (a) elastic polyurethane resin base;
  (b) methylene diphenyl diisocyanate (MDI) based polymeric,
  with OR without mixing implement AND/OR mixing gloves

SURFACE COATINGS, POLYURETHANE, having ALL of the following:
  (a) anti-slip agent AND/OR additive having BOTH of 
      the following:
          (i) water content NOT less than 14%;
         (ii) binder,
  (b) hardening agent AND/OR additive having a polyisocyanate 
      content NOT less than 1%;
  (c) class P5 slip resistance in accordance with AS (Australian
      Standard) 4568-2013

FILLING COMPOUND, PNEUMATIC TYRE, polyurethane

POLYURETHANE RESIN, comprising ALL of the following;
 (a) polyalcohol;
 (b) ester;
 (c) ether;
 (d) polyisocyanate;
 (e) diphenylmethane-diisocyanate isomere

EXPANDING FOAM, put up in aerosol cans containing polyurethane foam
 pre-polymer solution, having ALL of the following:
   (a) active ingredient of diphenyl methane diisocyanate;
   (b) propellant of hydrocarbon;
   (c) weight of can contents NOT greater than 1 000 g

PRINTING INK BINDERS AND ADHESION PROMOTERS, being solutions of
 aromatic or aliphatic non reactive polyurethane resins

DISPERSIONS, AQUEOUS, ALIPHATIC, POLYURETHANE, with a solid content
 range of 23% to 39% and Ph between 7 and 9.5

ADHESIVE, polyurethane, one component, waterproof

URETHANE RESIN, aromatic, diacrylate oligomer

URETHANE RESINS, containing cross linkable blocked isocyanate groups

EXPANDING FILLER, put up in aerosol cans containing polyurethane
 foam pre-polymer solution having ALL the following:
   (a) active ingredient of diphenyl methane diisocyanate;
   (b) propellant of hydrocarbon;
   (c) pre-polymer solution capable of expanding its volume up to 25
       times after extrusion from can as foam;
   (d) weight of can contents NOT greater than 1000 g

WATER-BORNE POLYURETHANE DISPERSION, aromatic or aliphatic type

ADHESIVES, laminating, amine terminated urethane polymer

POLYURETHANE ADHESIVE,hot melt,moisture reactive curing

ELASTOMER RESINS, having BOTH the following: 
  (a) methylene diphenyl diisocyanate (MDI) based polyurethane;
  (b) polyester backbone

POLYDIMETHYLSILOXANES, modified with reactive cure sites OTHER
 THAN silanol (hydroxyl bonded to silicon), NOT being emulsions
 or aqueous solutions

SILICONE ELASTOMER PRIMARY FORMS, heat vulcanising type

SILICONE SOLIDS OR FLUIDS, phenyl methyl, containing 10% or more
 by weight of phenyl groups

SILICONE ELASTOMER MOULDING COMPOUNDS, of the two part room
 temperature vulcanising type

SILICONE FLUIDS, methyl hydrogen

SILICONE FLUIDS, methoxy functional

METHYL ALKYLARYL POLYSILOXANE COPOLYMER BASED PAINT ADDITIVES

STABILISERS, POLYURETHANE FOAM, being organo-modified polysiloxanes

SILICONE MOULDING COMPOUNDS, two part, of the room temperature
 vulcanising elastomer type

SILICONE RUBBER BASE, primary form, of the heat vulcanising
 elastomer type

METHYLPOLYSILOXANES, oligomerous, containing reactive ethoxy and
 hydroxyl groups

SILOXANES, POLYDIMETHYL AND/OR POLYMETHYLVINYL, with OR without 
curing regulation additives

FLUIDS, POLYDIMETHYLSILOXANE

PETROLEUM HYDROCARBON RESINS, having a softening point NOT
 greater than 145 degrees C by the ball and ring method

COUMARONE-INDENE RESINS

PETROLEUM HYDROCARBON RESINS, having a softening point NOT greater
 than 170 degrees by the ball and ring method.

SODIUM SALT, naphthalene sulphonic acid polymer with formaldehyde

CYCLOHEXANONE ALDEHYDE RESIN

POLYISOCYANATE CROSS LINKING AGENTS, produced with 0.5% or LESS
 free isocyanate monomer

POLYCAPROLACTONE

POLYETHYLENEIMINES

STABILIZERS, light, hindered amine, polymeric

TERPENE PHENOLIC RESINS

HYDROCARBON RESINS, having a softening point NOT greater than 145
 degrees C by the ball and ring method

1,2-ETHANEDIAMINE, being a polymer with (chloromethyl) oxirane 
and N-methylmethanamine

SOLUTIONS, POLYMALEIC ACID

EPICHLOROHYDRIN AND DIMETHYLAMINE COPOLYMER, in liquid form

RESIN, POLYETHERSULFONE, in pellet form, having ALL of the 
following:
  (a) tensile modulus 7 300 MPa;
  (b) density 1 500 kg/m3;
  (c) melt volume flow rate at 360 degrees C/10 kg of 29 cm3/10 
      minutes;
  (d) 20% glass fibre reinforcement
Tolerances of + 10% and - 10% are allowable for specifications 
(a) through to (d)

THERMOPLASTIC POLYMERS, ALIPHATIC POLYKETONE

CELLULOSE NITRATE, with a number average molecular weight of
 less than 500 000

ADHESIVE, MEDICAL ELECTRODE, being collodion dissolved in diethyl
 ether and methylated spirit

CELLULOSE NITRATE

CELLULOSE ETHERS

CARBOXYMETHYLCELLULOSE, in powder form

CELLULOSE ETHERS

CELLULOSE, alpha or micro-crystalline

CELLULOSE ESTERS, unplasticised

CELLULOSE ACETATE BUTYRATE, plasticised

ALGINIC ACID, its salts and esters

AGAROSE GRADED, natural polymer

POLYDEXTROSE

XANTHAN GUM

CHLORINATED RUBBER

SODIUM HYALURONATE

GELLAN GUM

SODIUM DEXTRAN SULPHATE

GELLING AGENT, liquid form, having a basis of Xanthan Gum

GUM, in powder form, water soluble, having CAS registration 
numbers 125005-87-0 OR CAS registration number 595585-15-2

PENTOSAN POLYSULFATE SODIUM, in salt form

DEXTRAN, in EITHER of the following forms:
  (a) liquid;
  (b) granules AND/OR powders

POLYMERS, STARCH BASED, BIODEGRADABLE

CHONDROITIN SULPHATE

SODIUM DEXTRAN SULPHATE

ION EXCHANGERS, based on polymers classified under headings
 3901 to 3911

ION EXCHANGE RESINS, bead OR gel form, being ANY of the 
following:
  (a) acid cation resin with a particle size NOT less than
      0.400 mm and NOT greater than 1.2500 mm;
  (b) base anion resin type II with a particle size NOT less 
      than 0.300 mm and NOT greater than 1.250 mm;
  (c) base anion resin being EITHER of the following:
        (i) having a particle size NOT less than 0.500 mm and 
            NOT greater than 0.700 mm; 
       (ii) having a particle size NOT less than 0.300 mm and NOT
            greater than 0.710 mm;
  (d) absorbent resin with a particle size of NOT less than 
      0.44 mm and NOT greater than 0.64 mm

ION EXCHANGERS, being insoluble agarosa, cross-linked with 
polyvinyl pyrrolidone, spherical in shape

TRIMMINGS, polyvinyl chloride (PVC)

RODS, thermoplastic

POLYVINYL CHLORIDE RODS, dia 6 mm or greater

ROOF FITTINGS, thermoplastic polyolefin OR polyvinyl chloride 
with OR without ANY of the following:
  (a) end caps;
  (b) aluminium box section;
  (c) stainless steel fasteners

MOULDED NYLON HOOK TAPE, loop surfaced fastening system, whether OR
 NOT adhesive backed

POLYCARBONATE PROFILE SHAPES, twin wall

STRING, TENNIS AND/OR SQUASH RACKET, co-polyester monofilament

BOARDS, either ALL plastic OR microfibre-reinforced plastic, 
with OR without metal profiles, in the following dimensions:
  (a) thickness NOT less than 40 mm and NOT greater than 60 mm;
  (b) width NOT less than 900 mm and NOT greater than 1 455 mm;
  (c) length NOT less than 1100 mm and NOT greater than 1 305 mm

BOARDS, plastic, having ALL of the following:
  (a) thickness NOT less than 35 mm and NOT greater than 60 mm;
  (b) width NOT less than 900 mm and NOT greater than 1 430 mm;
  (c) length NOT less than 1 100 mm and NOT greater than 1 305 mm
with OR without microfibre

PROFILES, polyurethane, having ALL of the following:
  (a) length NOT less than 2 600 mm and NOT greater the 5 700 mm:
  (b) density NOT less than 270 kg/m3 and NOT greater 500 kg/m3;
  (c) ignition temperature NOT greater than 310 degrees Celsius;
  (d) thermal conductivity NOT less than 0.045 W/mK and NOT 
      greater than 0.06 W/mK;
  (e) volumetric water absorption NOT greater than 0.3%

SHEETS, polycarbonate, multiwall, with OR without tongue AND 
groove connection

RODS, polyacetal, having a length NOT greater than 3 100 mm

RODS, polyamide, having a length NOT greater than 3 100 mm

SHEETS, polycarbonate, twin wall cellular structure, having a 
thickness NOT less than 8 mm and NOT greater than 10 mm

STRENGTH MEMBER RODS, OPTICAL CABLE, tensile modulus greater 
than 45 GPa, having ANY of the following:
  (a) glass reinforced plastic;
  (b) fibreglass reinforced plastic;
  (c) glass fibre reinforced plastic;
  (d) E-glass fibre with resin

PANELS, polycarbonate, having a multi-walled cellular internal 
structure, with polycarbonate joiners

PANELS, polyvinyl chloride OR polycarbonate, extruded, tongue-
and-groove interlocking, having a width NOT less than 60 mm and 
NOT greater than 120 mm

RODS, WELDING, THERMOPLASTIC, on spools

EDGING, acrylic, continuous rolls, having BOTH of the following:
   (a) width NOT less than 20 mm and NOT greater than 45 mm;
   (b) thickness NOT less than 1 mm and NOT greater than 2 mm

PIPE AND ELBOW LINERS, polytetrafluoroethylene

PIPE, high density polyethylene, thermoplastic, having ALL of the
 following characteristics:
   (a) petrol permeability NOT to exceed 2 grams per sqm per day
       being total weight loss of content of pipe permanently filled
       with petrol;
   (b) design, manufacture and inspection conforming to ALL of the
       following:
          (i) BS5750 (Part 1);
         (ii) ISO 9001;
        (iii) EN 29001
   (c) size, as follows, conforming to DIN 8074 and BS 5556 Standards
       Outside Diameter                   Nominal Wall Thickness
          (i) 110mm                             6.5mm
         (ii)  90mm                             6.0mm
        (iii)  63mm                             6.0mm

TUBES, sintered, moulded, pervious, high density polyethylene

PIPE, POLYETHYLENE COMPOSITE, cross helically-wound steel wire 
skeleton, pressure rating NOT less than 2.5 MPa and NOT greater 
than 7.5 MPa, having one OR more of the following:
  (a) polyethylene electrofused pipe end inserts;
  (b) crimped steel sleeve pipe ends;
  (c) elastomeric seal

PIPE, MULTILAYER, comprising ALL of the following:
  (a) cross-linked polyethylene inner layer;
  (b) adhesive layers;
  (c) aluminium middle layer;
  (d) cross-linked polyethylene outer layer

SHEATHING, OPTICAL FIBRE CABLE

TUBING, extruded, cross linked, foamed, closed cell high density
 polyethylene

CABLE PROTECTORS, divisible, polypropylene OR propylene AND  
ethylene propylene diene monomer, including ALL of the following:
  (a) length NOT less than 1 000 mm and NOT greater than 
      1 200 mm;
  (b) diameter NOT less than 60 mm and NOT greater than 250 mm;
  (c) side locks

PIPES, having ALL of the following:
  (a) polypropylene middle AND outer layer;
  (b) calcium carbonate filler inner;
with OR without sockets AND/OR plain ends

NOISE REDUCTION PIPES, polypropylene with a middle layer filler 
of barium sulphate, with OR without sockets AND/OR 
plain ends

STRAWS, DRINKING, polypropylene, shaped and/or twisted and/or 
bent, with OR without novelty fittings

PIPING AND/OR TUBING, POLYPROPYLENE

DRINKING STRAWS, manufactured from polyvinyl chloride straight
 resin, each straw having one or more twist, curl or spiral, NOT
 being straw manufactured from polypropylene

PIPES, FIRE SPRINKLER, chlorinated polyvinyl chloride(CPVC, 
complying with Australian Standard AS 4118.2.1-1995

LINERS, PIPE, glass reinforced polymer AND unsaturated polyester 
resin

PIPES AND/OR PIPE SPOOLS, fibreglass reinforced plastic, vinyl 
ester resin, with OR without fittings

TUBING, ribbed or plain, fibreglass reinforced isophthalic 
polyester resin AND/OR fibreglass reinforced vinyl ester resin, 
having a diameter NOT greater than 50 mm

JACKING PIPES, centrifugally cast glass fibre reinforced 
plastic, with OR without couplings OR seals, having an outside 
diameter 
NOT less than 2 999 mm

PIPES, vinyl ester resin, fibreglass reinforced, having a bore 
size less than 100 mm

TUBING, ribbed or plain, fibreglass reinforced isophthalic 
polyester resin AND/OR fibreglass reinforced vinyl ester resin

TUBES, BUSHING STOCK, plastic, having ALL of the following:
  (a) length NOT greater than 105 cm;
  (b) melting point NOT less than 250 degrees celsius;
  (c) compression strength at yield NOT less than 90 MPa;
  (e) dynamic unlubricated friction co-efficient on 
      steel 0.12-0.20

PIPES, EPOXY RESIN, GLASS FIBRE REINFORCED

HOSE, flexible, polytetrafluorethylene core, having ALL of the
 following:
   (a) stainless steel wire braid outer cover;
   (b) service temperature range of -73 to 232 deg.C
       (both inclusive);
   (c) conforming with one of the specifications in lines i) to vi)
       inclusive in the following table:
                             TABLE
    Inside  dia.   Outside dia.    Minimum Working      Minimum Bend
    of core        of core         Pressure             Radius
    nominal (mm)   nominal (mm)    nominal (mPa)        nominal (mm)
 i)    4.7            7.9             20.685               50.8
 ii)   6.35           9.52            20.685               76.2
 iii)  7.9            11.1            17.237               101.6
 iv)   10.3           13.49           13.79                127
 v)    12.7           15.87           10.34                165.1
 vi)   15.87          19.             8.274                190.5

HOSE, stainless steel braided polytetrafluoroethylene, smooth
 bore and convoluted

HOSE, nylon core tube, specification SAE100R7
 NOTE: Because of the Tariff change on 1 July 1993, the tariff
      classification applicable to the goods described is 3917.31.00
      from the 0perative Date to 30 June 1993.

HOSES AND/OR PIPING, REINFORCED THERMOPLASTIC, SPOOLABLE AND/OR 
FLEXIBLE, with OR without fittings, having ALL of the following: 
  (a) high density polyethylene cover, liner AND reinforcing
      tape matrix; 
  (b) aluminium foil anti-permeation layer; 
  (c) high strength steel cable reinforcement; 
  (d) burst pressure NOT less than 45 MPa at 20 degrees Celsius

THERMOPLASTIC HOSE, conforming to European Standard EN 
1736:2008, with OR without end fittings, including ALL of the 
following: 
  (a) temperature range of -45 to 130 degrees Celsius;
  (b) minimum burst pressure exceeding 30 MPa;
  (c) inner diameter NOT less than 2 mm and NOT greater than
      6.1 mm;
  (d) outer diameter NOT less than 6 mm and NOT greater than
      10.9 mm

SUBSEA FLYING LEADS, hydraulic, with OR without reeling unit, 
having ALL of the following:
  (a) extruded polyurethane inner AND outer sheath;
  (b) NOT less than 5 hoses; 
  (c) steel wire reinforcement braid;
  (d) connectors;
  (e) outer jackets;
  (f) thermoplastic liners

FLOWLINES, SUBSEA, flexible, thermoplastic, with OR without 
skid, including ANY of the following;
  (a) bend restrictors; 
  (b) end fittings AND/OR connectors;
  (c) mounted in reels AND/OR drums AND/OR spools

HOSES, with OR without fittings, with OR without reel spool 
AND/OR reeling system, having ALL of the following:
  (a) minimum burst pressure exceeding 200 MPa;
  (b) multiple spiral layer high-tensile steel wire reinforced;
  (c) plasticised nylon inner core AND inner layer;
  (d) thermoplastic polyurethane outer cover

UMBILICALS, SUBSEA, on spools AND/OR reeler drums, including ALL
of the following:
  (a) polyurethane inner AND outer sheath;
  (b) fibre reinforced;
  (c) fibre braid;
  (d) NOT less than 4 reinforced hoses;
  (e) hose fittings AND/OR connectors

THERMOPLASTIC HOSE, having ALL of the following:
   (a) reinforced with multiple layers of spirally-wound steel 
wire;
   (b) a maximum working pressure in excess of 65 MPa;
   (c) with or without endfittings

HOSES, with OR without hose connectors AND/OR plastic caps, 
having ALL of the following:
  (a) polyamide inner layer;
  (b) synthetic textile fibre reinforcement layer;
  (c) polyamide outer layer;
  (d) inner diameter NOT greater than 4 mm

HOSES, with OR without fittings, whether OR not reel mounted OR 
assembled lengths, having ALL of the following:
  (a) thermoplastic elastomer OR polyether polyurethane core;
  (b) polyurethane cover;
  (c) reinforced single OR multiple braided fibre;
  (d) burst pressure NOT less than 40 MPa and NOT 
      greater than 110 MPa

HOSES, PRESSURE TESTING, thermoplastic, inside diameter NOT 
greater than 4 mm

FLYING LEADS, FLUID, SUBSEA, with OR without lockable stainless 
steel stab plates, having ALL of the following:
  (a) thermoplastic conduit; 
  (b) stainless steel swaged end fittings;
  (c) stainless steel hydraulic couplers

TUBES, heat shrinkable, capable of withstanding voltages greater
 than 1 kV, when measured according to Test 4 of ESI Standard
 09-13 of October 1981, having a recovered wall thickness greater
 than 1 mm and a pre-shrunk diameter greater than 28 mm

TUBING, polytetrafluoroethylene, having a continuous use
 temperature rating of 260 degrees C and a short term dielectric
 strength of 1 400 volts/0.0254 mm wall thickness (ASTM D149)

SLEEVES, cold shrink, silicone rubber, expanded around a spiral
 welded polypropylene core

TUBING, heat shrinkable, seamless, layflat, polyvinylidene chloride
 (PVDC), up to 75 mm width

TUBING, HEAT SHRINKABLE, being ANY of the following:
   (a) elastomeric;
   (b) fluoro elastomeric;
   (c) fluorocarbon;
   (d) nylon

CONDUIT, flexible, nylon having ALL of the following features:
   (a) self extinguishing material to UL94Vo;
   (b) UV stabilised;
   (c) zero halogen rated;
   (d) having a service temperature range of -10 degrees C to 80
       degrees C

TUBING, perfluoroalkoxy, having BOTH of the following:
   (a) maximum working pressure of 850 kPa or greater;
   (b) OD NOT exceeding 13 mm
 NOTE: Because of the Tariff change on 1 July 1993, the tariff
      classification applicable to the goods described is 3917.32.00
      from the Operative Date to 30 June 1993.

HEAT SEAL ROLLS, including All of the following:
  (a) multiple layers of polyethylene, with OR without nylon
      plastics;
  (b) width NOT greater than 28 cm;
  (c) closures on two edges;
  (d) embossed

DRIP TAPE, IRRIGATION, gravity fed, having ALL of the 
following: 
  (a) lay flat polyethylene tubing in rolls;
  (b) internal diameter NOT less than 19 mm and NOT greater than
      49 mm;
  (c) embedded emitters

TUBING, SHRINK, lay-flat, having ALL of the following:
  (a) multi-layer structure consisting of NOT less than 5 
      coextruded layers; 
  (b) cross-linked polymer external surface; 
  (c) total shrinkage NOT less than 50% at 85 degree Celsius; 
  (d) water vapour transmission rate NOT greater than 35 
      gr/m2/24hrs; 
  (e) thickness NOT less than 30 microns and NOT greater than 
      150 microns;

TUBES, SILAGE, polyethylene, having BOTH of the following:
  (a) length NOT greater than 100 m;
  (b) diameter NOT less than 2.7 m and NOT greater than  2.8 m

TUBES, SILAGE, polyethylene, having BOTH of the following:
  (a) length NOT greater than 90 m;
  (b) diameter NOT less than 2.7 m and NOT greater than  2.8 m

CASSETTES, WASTE HANDLING

TUBING, lay flat, multi-layered, having ALL of the following:
  (a) polyamide nylon;
  (b) polyethylene terephthalate;
  (c) ethylene vinyl alcohol;
  (d) polyethylene,
with OR without starch powder

TUBING, shrink, oriented polystyrene, having a thickness NOT 
less than 95 microns

PIPES, FUEL, electrofusion, high-density polyethylene, in coils 
OR straight lengths, having ALL of the following:
  (a) clear ethylene vinyl-alcohol inner liner;
  (b) pressure rating NOT greater than 10 bar;
  (c) primary colour being black with green stripes;
  (d) temperature rating NOT less than -40 degrees Celsius and
      NOT greater than 50 degrees Celsius
with OR without liners

PIPES, multilayered, with OR without conduit sleeve, having ALL 
of the following:
  (a) peroxide cross-linked polyethylene inner layer;
  (b) high-density polyethylene layer;
  (c) outer diameter NOT greater than 33 mm;
  (d) mean wall thickness NOT less than 2.2 mm and NOT greater  
      than 5.5 mm;
  (e) compliance with Australian/New Zealand Standard 
      (AS/NZS) 2492:2007

TUBING, shrink, lay flat, having ALL of the following:
  (a) width NOT less than 300 mm;
  (b) shrinkage rate NOT less than 60% at 85 degrees Celsius;
  (c) oxygen transmission rating NOT greater than 5 000 
      cc/sqm/24hr at 23 degrees Celsius

HOSES, VACUUM CLEANER

TUBING, in coils, multilayer, flexible, having BOTH of the 
following:
  (a) internal diameter NOT less than 4 mm and NOT greater than 
      13 mm;
  (b) length NOT less than 150 m

SLEEVES, PAPER PRESS, polyester multifilament, polyurethane 
coated

TUBING, heat shrinkable, polyethylene terephthalate (PET) OR 
oriented polystyrene (OPS), having a thickness NOT less than 
30 micrometres and NOT greater than 60 micrometres

TUBING, OXYGEN DIFFUSION BARRIER, comprising ALL of the 
following:
  (a) cross linked polyethylene inner layer;
  (b) adhesive layers;
  (c) ethylene vinyl alcohol copolymer middle layer;
  (d) cross linked polyethylene outer layer

STRAWS, polypropylene, paper wrapped

U-STRAWS, DRINKING, polypropylene

PIPES, high density polyethylene outer, polyamide inner

CONDUITS, ELECTRICITY, flexible, nylon

HOSE, test, thermoplastic, hydraulic, having an ID NOT exceeding
 4 mm and a minimum test pressure of 25 MPa, fitted with couplings

FLUID TRANSFER SETS, MEDICATIONS, including ALL of the following:
  (a) Luer lock adaptor AND/OR connector;
  (b) closure pinch clamp;
  (c) vented spike;
  (d) retainers

POLYURETHANE HOSE, having ALL of the following:
   (a) reinforced with woven fabric;
   (b) incorporating extruded power cable support rib;
   (c) ID 24 mm or greater but NOT exceeding 153 mm;
   (d) maximum working pressure exceeding 1.03 MPa

HOSE, silicone rubber, reinforced to Part I Specification SAE
 J20E, ID 6.35 mm to 127.00 mm (both inclusive), continuous
 service temperature exceeding 175 degrees C

HOSE, lay flat, polyvinyl chloride lining and cover, fabric
 reinforced, ID NOT less than 152 mm, having a minimum burst
 pressure of 4.1 MPa

CONDUIT, flexible, having BOTH of the following:
   (a) spiral inner core of PVC;
   (b) smooth outer surface of flexible PVC

HOSE, non-twist, with shower head connectors

HOSE, stainless steel braided polytetrafluoroethylene, convoluted,
 with connection fittings

HOSE, thermoplastic, flexible, liquidtight, crush resistant, having
 an internally ribbed outer cover

PIPES, multilayered, with OR without insulation, having ALL of 
the following:
  (a) polyethylene of raised temperature (PR-RT) inner layer;
  (b) aluminium middle layer;
  (c) polyethylene of raised temperature (PR-RT) outer layer

PIPE LINERS, lay flat, multilayered, including ALL 
of the following:
  (a) polyethylene AND polyamide outer AND inner protective  
      foil; 
  (b) unsaturated polyester resin AND vinylester resin composite 
      inner foil;
  (c) glass fleece OR polyester fleece wear layer

HOSES, having ALL of the following:
  (a) inner hose working pressure of 72 MPa with a burst
      pressure of 288 MPa;
  (b) outer return hose working pressure of 
      2.5 MPa with a burst pressure of 10 MPa;
  (c) connectors

HOSES, spiral wire reinforced, whether OR not drum OR reel 
mounted, including ALL of the following:
  (a) polyamide inner layer;
  (b) thermoplastic polyurethane layer;
  (c) burst pressure NOT less than 82 MPa;
  (d) working pressure NOT less than 34 MPa,
with OR without ANY of the following:
           (i) unions;
          (ii) swivels;
         (iii) hubs;
          (iv) threaded ends

UMBILICALS, SUBSEA, wound on drums, including ALL of the 
following:
  (a) polyurethane inner AND outer sheath;
  (b) fibre braid;
  (c) fibre AND/OR extruded fillers;
  (d) NOT less than 24 reinforced hoses, with OR without spiral 
      guards;
  (e) hose fittings AND/OR connectors

UMBILICALS, SUBSEA, with OR without hydraulic reeler, including 
ALL of the following: 
  (a) NOT less than 6 hoses; 
  (b) polypropylene fillers; 
  (c) steel armour wires; 
  (d) connectors

TUBING, slip-lining, multi-layered, plastic, having ALL of the 
following:
  (a) outer layer of polyethylene sheath;
  (b) inner layer of polyethylene OR thermoplastic polyurethane;
  (c) middle layer of single OR double seamless aramid fibre OR
      aramid AND polyester fibre

PIPE LINERS, glass fibre, neopentylglycol polyester resin 
impregnated

PIPES, multilayered, with OR without insulation, having ALL of 
the following:
  (a) cross linked polyethylene inner layer;
  (b) adhesive layers;
  (c) aluminium middle layer;
  (d) polyethylene outer layer

TUBES, lay flat storable, polyvinylchloride (PVC), textile 
coated, flexible, complying with International Organization for 
Standardization standard ISO 3795-1976(E)

UMBILICALS, CHEMICAL INJECTION AND HYDRAULIC FLUID, SUBSEA, with 
OR without reeling module, having BOTH of the following:
  (a) NOT less than six hoses;
  (b) connectors

HOSE AND/OR TUBING, flexible, constructed from two layers of 
polyvinylchloride, inner layer embedded with steel spirals, 
with OR without polyester reinforced yarn

UMBILICALS, HYDRAULIC, GAS WELL, being EITHER of the following:
   (a) onshore;
   (b) subsea

UMBILICALS, hydraulic, subsea

HOSE, LAYFLAT, polyvinyl chloride OR polyurethane

TUBING, AIR BRAKE, conforming to Society of Automotive Engineers 
(SAE) J844 standard, having ALL of the following:
  (a) polyamide cores;
  (b) synthetic reinforcement fibres;
  (c) polyamide outer sheaths

HOSES, WIRE BRAIDED, REINFORCED

FITTINGS, HOSE OR PIPE, liquid or air, injection moulded
 polybutylene, PB-DP-D4137 polyolefin obtained by polymerisation of
 butene - 1 monomer, min class 16, Standards AS2642

FITTINGS, air hose or pipe, polybutylene terephthalate, quick
 connect, able to withstand working pressures NOT exceeding
 900 kPa

PIPE FITTINGS, PVC, 150 mm diameter OR greater

PIPELINE COMPRESSION FITTINGS, polypropylene, complying with
 Australian Standard AS1460 Part 1, 1989, OR AS/NZS 4129 (Int)
 1997, being ANY of the following:
   (a) couplings having an OD of 125 mm OR 160 mm;
   (b) reducing couplings having ODs of 75 mm x 50 mm or
       90 mm x 63 mm;
   (c) slip repair couplings having an OD of 125 mm OR 160 mm;
   (d) male adaptors having ODs of 75 mm x 65 mm (2.5"),
       90 mm x 50 mm (2"), 90 mm x 100 mm (4"), 110 mm x 50 mm (2")
       110 mm x 80 mm (3"), 75 mm x 40 mm (1.5") OR 75 mm x 65 mm
       (2.5");
   (e) female adaptors having ODs of 75 mm x 65 mm (2.5"),
       90 mm x 50 mm (2"), 90 mm x 100 mm (4") or
       110 mm x 80 mm (3");
   (f) 45 degree elbows having ODs of 90 mm or 110 mm;
   (g) female elbows having ODs of 75 mm x 65 mm (2.5") or
       75 mm x 80 mm (3");
   (h) male elbows having ODs of 75 mm x 65 mm (2.5"),
       75 mm x 80 mm (3"), 90 mm x 80 mm (3") or
       90 mm x 100 mm (4");
   (i) elbow adaptors having ODs of 63 mm to 50 mm;
   (j) reducing tees having an OD of 75 mm x 63 mm;
   (k) 45 degree tees having ODs of 75 mm, 90 mm or 110 mm;
   (l) female tees having ODs of 75 mm x 80 mm (3");
   (m) coupling O risers having ODs of 75 mm x 20 mm (0.75")
       or 75 mm x 25 mm (1");
   (n) flanged couplings having ODs of 75 mm x 80 mm (3"),
       90 mm x 100 mm (4"),125 mm x 125 mm (5") or
       125 mm x 150 mm (6");
   (o) shoulder adaptors having an OD of 90 mm x 100 mm (4") OR
       160 mm x 150 mm;
   (p) adaptor flanges having ODs of 75 mm x 65 mm (2.5"),
       75 mm x 80 mm (3"), 90 mm x 100 mm (4") 110 mm x 125 mm (5"),
       160 mm x 125 mm (5") OR 160 mm x 150 mm (6");
   (q) compression saddles having ODs of 140 mm or 160 mm,
       and having polyethylene pipe compression outlets;
   (r) reducing sets having ODs of 63 mm to 25 mm or 63 mm to 40 mm;
   (s) flanged couplings having ODs of 160 mm x 125 mm (5") or
       160 mm x 150 mm (6");
   (t) tees having an OD of 160 mm;
   (u) 90 degree elbows having an OD of 160 mm;
 NOTE: Bracketed dimensions e.g. 65 mm (2.5"), 50 mm (2") refer to
       the dimensions of either British Standard Pipe (BSP) threads
       or flange face dimensions. A tolerance of + or - 2% applies
       to all dimensions

FITTINGS, UNDERGROUND PETROLEUM PIPE, weldable, medium density
 polyethylene

FITTINGS, TUBE, PERFLUOROALKOXY (PFA), tube OD NOT exceeding 13 mm,
 pressure rating at 20 degrees celsius of 850 kPa or greater

PIPE FITTINGS, high density polyethylene, thermoplastic having ALL
 of the following characteristics:
   (a) petrol permeability NOT to exceed 2 grams per sqm per day
       being total weight loss of content of fitting;
   (b) design, manufacture and inspection conforming to ALL of the
       following:
          (i) BS 5750 (Part 1);
         (ii) ISO 9001;
        (iii) EN 29001
   (c) designed and manufactured to meet British Gas Specification
       BG PS/PL2, Parts 4 and 6

PIPE FITTINGS, ELECTROFUSION, polyethylene

PIPE FITTINGS, incorporating internal heating elements

FITTINGS, pipe, having the United States Screw Thread Standard, NTP
 (National Pipe Thread)

PIPE FITTING, swivel coupling, unplasticised polyvinyl chloride

ASEPTIC DISCONNECTORS, TUBING, polycarbonate

PIPE FITTINGS, ASEPTIC, polycarbonate

PIPE FITTINGS, high density polyethlene, being any of the 
following:
  (a) stub ends;
  (b) elbows;
  (c) reducers AND/OR tees

PIPE FITTINGS AND CAP, plastic, lockable

FITTINGS, TUBE AND PIPE, push-fit, NOT including garden hose 
fittings, having a tube outer diameter NOT exceeding 33 mm

PIPE AND/OR SANITARY FITTINGS, electro-fusible AND/OR butt-
weldable, high density polyethylene, being ANY of the 
following:  
  (a) reducers;
  (b) bends;
  (c) elbows;
  (d) branches; 
  (e) stack aerators;
  (f) connectors;
  (g) traps;
  (h) sockets;
  (i) protection plugs;
For the purposes of this order, the following ranges are 
allowable for items (a) to (i):
             (i) density NOT less than 0.94 grams per cubic
                 centimetre and NOT greater than 0.97 grams   
                 per cubic centimetre;
            (ii) operational temperature NOT less than minus 
                 40 degrees Celsius and NOT greater than 105 
                 degrees Celsius;
           (iii) outer diameter NOT less than 32 mm and NOT
                 greater than 316 mm

COUPLERS AND/OR FITTING KITS, being EITHER of the following:
  (a) collet kits, consisting of BOTH of the following:
             (i) glass filled nylon AND/OR stainless steel 
                 collets;
            (ii) seals AND/OR O-rings AND/OR washers,
  (b) female couplers, consisting of ALL of the following:
             (i) polysulphone bodies AND/OR caps;
            (ii) glass filled nylon AND/OR stainless steel 
                 collets;
           (iii) seals AND/OR O-rings

PRESS CONNECTION SYSTEM, GAS OR WATER PIPING, including ALL of 
the following:
  (a) polyamide fitting body having BOTH of the following:
            (i) NOT less than 50% by weight of fibreglass 
                reinforcement;
           (ii) connectors having an outer diameter NOT less 
                than 32 mm and NOT greater than 63 mm,  
  (b) polyoxymethylene clamping ring;
  (c) polyamide sliding sleeve having NOT less than 35% by weight
      of fibreglass reinforcement

FITTINGS, electrofusion, high density polyethylene, including 
ALL of the following:
  (a) diameter NOT less than 32 mm and NOT greater than 315 mm;
  (b) density NOT less than 0.94 g/cm3 and NOT greater than 
      0.97 g/cm3;
  (c) operating temperature NOT less than -40 degrees Celsius 
      and NOT greater than 80 degrees Celsius;
  (d) reducers;
  (e) bends;
  (f) elbows;
  (g) branches;
  (h) stack-aerators;
  (i) connection fittings;
  (j) sanitary fittings;
  (k) traps

FITTINGS, NOISE REDUCTION PIPE, polypropylene with a middle 
layer filler of barium sulphate, being ANY of the 
following:
  (a) double sockets;
  (b) reducer eccentrics;
  (c) sleeve sockets;
  (d) elbows;
  (e) branches;
  (f) swept bends;
  (g) socket plugs;
  (h) expansion sockets;
  (i) double branches;
  (j) double corner branches;
  (k) 90 degrees clean out branches;
  (l) stack aerators;
  (m) vent cowls;
  (n) stack aerator sockets;
  (o) floor waste gully traps

FITTINGS, TUBE OR PIPE, polyphenylsulfone, with OR without 
embedded aluminium ring

PIPE FITTINGS, polyethylene, butt-fusion OR electrofusion, 
machined

TAPPING SADDLES, ELECTROFUSION WELD, with OR without pipe 
cutter, pipe diameter NOT greater than 250 mm

ACCESSORIES, VACUUM CLEANER, being ANY of the following:
   (a) interchangeable nozzles;
   (b) tube to machine connectors;
   (c) tube connection holding rings;
   (d) bent OR elbow pieces;
   (e) tube connection adaptors

HOSE FITTINGS, acrylonitrile-butadiene-styrene(ABS), whether OR 
not in sets, being ANY of the following:
  (a) hose connectors AND/OR couplings;
  (b) tap AND hose connectors;
  (c) tee shaped connectors;
  (d) elbow connectors;
  (e) sprinkler AND hose connectors;
  (f) hose AND/OR tap caps

FITTINGS, CONDUIT, polyamide, moulded

PIPELINE EXPANSION JOINTS, comprising BOTH of the following:
  (a) polytetrafluoroethylene bellows;
  (b) metal frame and flanges

FITTINGS, PLUMBING, being polyvinylidene fluoride (PVDF) 
compression sleeves, having ALL of the following:
  (a) certified pressure rating of PN20 (20 Bar/2MPa @ 20 
      degrees C) in accordance with Australian Standard/New
      Zealand Standard (AS/NZS) 2537-1994; 
  (b) pipe connectivity for cross-linked polyethylene (PE-X)
      pipe having BOTH of the following:
        (i) OD NOT less than 16 mm and NOT greater than 63 mm;
       (ii) WT NOT less than 2.2 mm and NOT greater than 8.6 mm,
        in accordance with Australian Standard/New Zealand
        Standard (AS/NZS) 2492:2007;
  (c) pipe connectivity for cross-linked polyethylene 
      (PE-X)/Aluminium multilayer pipe having both of the
      following:
        (i) OD NOT less than 16.2 mm and NOT greater than 40 mm;
       (ii) WT NOT less than 2.6 mm and NOT greater than 6 mm

PIPE FITTINGS, composite, having BOTH of the following:
  (a) polyphenylenesulfone body;
  (b) stainless steel press sleeve

FITTINGS, CAMLOCK, glass filled polypropylene OR glass 
filled polyamide

FITTINGS, PIPES, lead free, polyvinyl chloride (PVC)

PIPE FITTINGS, POLYETHYLENE OR POLYVINYLIDENE FLORIDE,  
butt-fusion injection moulded

FITTINGS, POLYPROPYLENE PIPING AND/OR TUBING

PIPE FITTINGS, FIRE SPRINKLER, chlorinated polyvinyl chloride 
(cpvc)

FITTINGS, PIPE, epoxy, fibreglass reinforced, being ANY of the
 following:
   (a) couplings;
   (b) elbows;
   (c) tees;
   (d) reducing tees;
   (e) reducers;
   (f) flanges;
   (g) nipples

FITTINGS, HOSE AND PIPE, pneumatic, quick connect and release type,
 but NOT including garden hose fittings

COVERINGS, FLOOR, vinyl, having ALL of the following:
  (a) thickness NOT less than 2 mm and NOT greater than 4 mm;
  (b) length NOT greater than 1 250 mm;
  (c) width NOT greater than 180 mm;
  (d) NOT less than 3 layers and NOT greater than 5 layers;
  (e) PVC backing

COVERINGS, FLOOR, vinyl, having ALL of the following:
  (a) thickness NOT less than 2 mm and NOT greater than 3.5 mm;
  (b) dimensions NOT greater than 1 000 mm x 500 mm;
  (c) NOT less than 3 layers and NOT greater than 5 layers;
  (d) PVC backing

POLYPROPYLENE FINE LINE PAINT MASKING TAPE, matt finished,
 thickness less than 0.12 mm, tensile strength less than 50 N/25 mm

SHEETING, reflective, incorporating or coated with glass beads,
 supported on a curl free release liner

ACRYLIC FOAM PLANAR FORMS, closed cell construction, thickness
 0.2 mm or greater, but NOT exceeding 3.0 mm, coated on both sides
 with an acrylic pressure sensitive adhesive

POLYPROPYLENE TAPE, mono axially oriented with high tensile
 strength and impact resistant, having ALL of the following:
   (a) film thickness 0.078 mm;
   (b) tensile strength in excess of 650 N/25 mm;
   (c) adhesion in excess of 13 N/25 mm

POLYPROPYLENE FASTENING TAPE, disposable nappy, coated on one side
 with physiologically inert adhesive, thickness NOT less than
 70 microns and NOT exceeding 180 microns

TAPE, electrical, insulating, consisting of polyester film,
 coated with a thermosetting acrylic adhesive, rated for
 continuous use at 130 degrees C or higher, conforming to AS1621

RETROREFLECTIVE MATERIAL, having CIL values for the relevant
 chromaticity co-ordinates NOT less than those specified in
 AS1906, AS2142 or AS2259

TAPE, self bonding, ethylene-propylene rubber, semi-conducting,
 rated for continuous operation at NOT less than 90 degrees C

POLYURETHANE ROLLSTOCK, closed cell construction, unplasticised,
 coated on one side with a pressure-sensitive adhesive and
 having a protective removable paper liner

POLYVINYL CHLORIDE TAPE, electrical insulating, pressure sensitive
 adhesive coated, having an elongation of 100% or greater of the
 original sample when tested in accordance with ASTM D 1000

POLYTETRAFLUOROETHYLENE PLANAR FORMS, adhesive backed

PLANAR FORMS, composed of polyethylene foam, coated on both sides
 with a pressure sensitive adhesive, thickness 0.8 mm or greater
 but NOT exceeding 1.5 mm

POLYVINYL CHLORIDE TAPE, surgical colour coding, gas and steam
 permeable, thickness 0.11 mm or greater but NOT exceeding 0.14 mm

INDICATORS, temperature, self-adhesive, consisting of one or
 more heat sensitive indicators which change colour at designated
 temperatures

PLANAR FORMS, composed of polyurethane, coated on both sides with
 pressure sensitive adhesive, having a thickness of 0.762 mm to
 6.350 mm (both inclusive)

BOLSTER STRIPS, FOLDING CARTON, adhesive backed, creasing

FILMIC TAPE with permanent adhesive on one side and removable on the
 other

MOUNTING ADHESIVE, double coated clear polyester film, having ALL of
 the following:
   (a) pressure sensitive acrylic adhesive;
   (b) total thickness NOT exceeding 93 microns;
   (c) capable of withstanding temperature range of -27 degrees C to
       149 degrees C;
   (d) capable of being applied at temperatures as low as -17
       degrees C;
   (e) positive adhesion to paper with a high moisture content

POLYPROPYLENE "TEARSTRIP" TAPE, consisting of a tensilized
 polypropylene backing coated on one side with a shear-resistant
 adhesive, thicknesses of 0.09 mm and 0.115 mm, width NOT exceeding
 10 mm

TAPE, composed of polyethylene, coated on both sides with pressure
 sensitive adhesive, having a thickness of 0.762 mm to 3.175 mm
 (both inclusive)

POLYESTER PLANAR FORMS, reinforced with glass or polyester
 filaments, pressure sensitive adhesive coated, without an interliner

TAPE, polypropylene, reinforced with glass or polyester filaments,
 pressure sensitive adhesive coated, without an interliner

MOUNTING TAPE, double sided, acrylate base

FILM TAPE, PVC, adhesive, having ALL of the following:
  (a) thickness NOT greater than 50 microns;
  (b) width NOT greater than 14 mm;
  (c) PET liner;
  (d) in rolls NOT greater than 30 m

FILM TAPE, POLYESTER, self-adhesive, having ALL of the following:
  (a) thickness NOT greater than 36 microns;
  (b) width NOT greater than 14 mm;
  (c) PET liner;
  (d) in rolls NOT greater than 30 m

SEALING TAPE, polyacrylate, including ALL of the following:
  (a) polyethylene film with polyethylene terephthalate filament 
      backing;
  (b) width NOT greater than 100 mm;
  (c) mounting temperature NOT less than 5 degrees Celsius and 
      NOT greater than 40 degrees Celsius;
  (d) thickness NOT greater than 285 microns

TAPE, double sided, having ALL of the following:
  (a) acrylic adhesive;
  (b) foam carrier;
  (c) polyethylene liner

TAPE, PVC, self adhesive, having ALL of the following:
  (a) pressure sensitive rubber adhesive coated on one side;
  (b) matt finish;
  (c) plasticised AND stabilised;
  (d) tape thickness NOT less than 190 microns and NOT greater 
      than 200 microns

TAPE, DUCT, SEALING AND/OR JOINING, polyvinylchloride

TAPE, self-adhesive, low density polyethylene film, having a 
thickness NOT greater than 0.12 mm

LINT REMOVERS, consisting of a roll of self-adhesive plastic 
tape, mounted on a revolving plastic handle, with OR without 
refill rolls

SETS, TAPE, comprising BOTH of the following:
  (a) cellulose self-adhesive tape;
  (b) dispenser

TAPE, self-adhesive, cellulose

TAPE SETS, consisting of BOTH of the following:
  (a) polypropylene or polyester self-adhesive tape;
  (b) dispenser

SHEETS, polyurethane, in rolls, having an acrylic adhesive 
backing

TAPE, SELF ADHESIVE, POLYPROPYLENE, mono-axially orientated 
having ALL the following:                                        
  (a) width NOT less than 12 mm;                                 
  (b) coated thickness NOT less than 0.06 mm;                    
  (c) tensile strength NOT less than 370 N/25 mm;                
  (d) clear synthetic rubber adhesive

TAPE, OPTHALMIC LENS PROTECTION

TAPE, SELF ADHESIVE, unplasticised polyvinyl chloride

TAPE, SELF ADHESIVE, polypropylene

TAPE, SELF ADHESIVE, polypropylene, having BOTH of the
 following:
   (a) width NOT greater than 15 mm;
   (b) thickness NOT greater than 125 microns

TAPE, TAMPER EVIDENT

FILM, WIND TURBINE BLADE, self-adhesive, polymer, pre-cut 
segments, having BOTH of the following:
  (a) elastomeric polymer top layer with erosion resistance of 
      NOT less than 550 hours; 
  (b) tensile strength NOT less than 40 MPa

MARINE VINYL, adhesive backing, having BOTH of the following:
  (a) width NOT less than 53 cm and NOT greater than 62 cm;
  (b) length NOT greater than 50 m

FILM, POLYESTER, acrylic adhesive, anti-graffiti, having ALL of 
the following:
  (a) thickness NOT less than 30 microns;
  (b) release liner;
  (c) width NOT less than 1 310 mm and NOT greater than 1 600 mm;
  (d) in rolls either 5 m, OR 10 m, OR 15 m, OR 30 m, OR 30.5 m,
      OR 50 m, OR 120 m

FILM, POLYESTER PET, acrylic adhesive, having ALL of the 
following:
  (a) thickness NOT less than 50 microns;
  (b) silicone coated liner;
  (c) width NOT less than 600 mm and NOT greater than 1300 mm;
  (d) in rolls either 5 m, OR 15 m, OR 30 m

APPLICATION TAPE, TRANSFER FILM, POLYETHYLENE, in rolls, having 
ALL of the following:
  (a) width NOT less than 500 mm and NOT greater than 1500 mm;
  (b) thickness NOT less than 150 ?m;
  (c) acrylic adhesive coating

FILM, polyurethane, in rolls, having BOTH of the following:
  (a) adhesive layer;
  (b) silicone PET layer

FILM, ADHESIVE, including BOTH of the following:
  (a) pressure sensitive adhesive layer; 
  (b) silicone coated release liner

FILM, polypropylene, thermosensitive, self-adhesive, in rolls, 
multi-layered, having ALL of the following:
  (a) width NOT less than 1 400 mm and NOT greater than 1 600 mm;
  (b) coated biaxially oriented polypropylene (BOPP) film having 
      a thermosensitive layer;
  (c) glassine liner having a basis weight NOT less than 54 g/m2 
      and NOT greater than 66 g/m2;
  (d) rubber based adhesive

POLYESTER FILM, coloured or clear, self adhesive, with removable
 liner

FILM, WINDOW, polyester, transparent

FILM, polyvinyl chloride, self adhesive, having ALL of the
 following:
   (a) perforated, print receptive layer;
   (b) liner having a circular printed pattern which aligns with the
       perforations in the print receptive layer;
   (c) light and heat restrictive

FILM, INK JET RECEPTIVE, polyvinyl chloride, self adhesive, in
 rolls, having ALL of the following:
   (a) film width of at least 600mm;
   (b) roll length of at least 12 metres;
   (c) film thickness NOT greater than 0.09mm

TAPE, printing plate mounting, being polyethylene foam laminated on
 both sides with polyethylene film and coated on both sides with a
 rubber adhesive, having a release liner on one side

SELF ADHESIVE PHOTO LUMINESCENT FLEXIBLE VINYL ROLLS

POLYVINYL CHLORIDE TAPE, electrical insulation, pressure
 sensitive adhesive coated, having an elongation of 100% or greater
 of the original sample when tested in accordance with ASTM D 1000

PLANAR FORMS, polyethylene foam, coated both sides with a pressure
 sensitive adhesive, having a thickness NOT exceeding 2.2 mm

TAPE, heavy duty, plasticzed polyvinyl chloride having ALL of the
 following:
   (a) thickness of 0.25 mm;
   (b) tensile strength of 106 N/25 mm;
   (c) elongation at break 230%;
   (d) adhesion power of 5.5 N/25 mm;
   (e) dielectric breakdown on 11 900V;
   (f) insulation of 1 x 10 tera ohms
 conforming to specification ASTM D 1000

INDICATOR TAGS, in plastic dispensers, having ALL of the following:
   (a) removable;
   (b) adhesive on one side;
   (c) with printed message and/or colour coded

FILM, cast polyvinyl chloride, having ALL of the following:
   (a) thickness (excluding adhesive) NOT exceeding 0.06 mm;
   (b) tensile strength (including adhesive) of 0.8 kg/cm or greater;
   (c) having a pressure sensitive adhesive coating;
   (d) a liner release having a weight NOT exceeding 20 g/cm

FILM, polyester OR polyvinyl chloride, having ALL of the following:
   (a) transparent;
   (b) coated with an acrylic based adhesive;
   (c) width exceeding 1 000 mm;
   (d) thickness greater than 50 microns;
   (e) silicone coated release liner

FILM, cast polyvinyl chloride, having ALL of the following:
   (a) pressure sensitive adhesive coating;
   (b) release liner;
   (c) peel strength of greater than 0.55 kg/cm in accordance with
       ASTMD-1000-61 m section 33-38;
   (d) elongation of less than 170 % in accordance with ASTM method
       D - 882-61T

TAPE, printing plate mounting, polyethylene foam, coated on both
 sides with an acrylic adhesive, having a release liner on one side

FILM, CAST POLYVINYL CHLORIDE, (but not including film manufactured
 by the calendered method) having ALL of the following:
   (a) film thickness not exceeding .0635mm (excluding adhesive);
   (b) solvent-based film formulation with cadmium-free properties;
   (c) less than .002% shrinkage performance rating;
   (d) a release liner

TAPE, ELECTRICAL, insulating, consisting of polyester film, coated
 with a thermosetting acrylic adhesive, rated for continuous use at
 130 degrees C or higher, conforming to AS 1621

POLYIMIDE PLANAR FORMS, coated with a silicone pressure sensitive
 adhesive, in rolls having a width NOT less than 280 mm and a
 length NOT less than 32 m

POLYESTER PLANAR FORMS, glass filament reinforced, having ALL of
 the following:
   (a) coated with an oil resistant pressure sensitive
       thermosetting electrical grade adhesive;
   (b) capable of withstanding temperatures of 130 degrees C or
       higher;
   (c) in rolls having a width NOT less than 960 mm and a length
       NOT less than 660 m

TAPE, printing plate mounting, polyvinyl chloride having ALL the
 following:
   (a) width 150 mm or greater;
   (b) thickness of 0.10 mm or greater but NOT exceeding 0.30 mm;
   (c) coated on both sides with pressure sensitive rubber adhesive

TAPE, plate mounting, polyvinyl chloride, having ALL of the
 following:
   (a) width of 300 mm or greater;
   (b) thickness 0.12 mm or greater, but NOT exceeding 0.55 mm;
   (c) coated on both sides with a pressure sensitive rubber
       adhesive

ACRYLIC FOAM PLANAR FORMS, closed cell construction, thickness
 0.2 mm or greater, but NOT exceeding 3.0 mm, coated on both sides
 with an acrylic pressure sensitive adhesive

COMPRESSABLE FLEXOGRAPHIC PLATE MOUNTING MATERIAL, having ALL of
 the following:
   (a) polyethylene closed cell construction;
   (b) coated on both sides with a pressure sensitive acrylic
       adhesive;
   (c) adhesion factors 9.0 N/25 mm to steel (open side), 6.5 N/25 mm
       to polyester (closed side);
   (d) thickness LESS than 2.5 mm

FILM, POLYESTER, reflective, having ALL of the following:
   (a) a silver metallized reflective coating, one side protected
       by a removable premask film;
   (b) coated one side with pressure sensitive adhesive;
   (c) in rolls NOT less than 1 200 mm wide;
   (d) reflectivity of NOT less than 92% when tested in accordance
       with ASTM E430

POLYURETHANE COMPRESSIBLE FLEXOGRAPHIC PLATE BACKING MATERIAL, open
 cell, micro-cellular, polyester supported, coated on one or both
 sides with pressure sensitive adhesive, having a thickness less
 than 6 mm

POLYURETHANE ROLLSTOCK, closed cell construction, unplasticised,
 coated on one side with a pressure-sensitive adhesive and
 having a protective removable paper liner

DISCS OR RECTANGULAR SHAPES, ostomy, self-adhesive

TAPE, transfer type adhesive, acrylic, laminating, in rolls
 having BOTH of the following:
   (a) width NOT less than 300 mm;
   (b) length NOT less than 100 m

RETROREFLECTIVE MATERIAL, having CIL values for the relevant
 chromaticity co-ordinates NOT less than those specified in
 AS1906, AS2142 or AS2259

MASKING TAPE OR PLANAR FORMS, polyvinyl chloride or polyvinyl
 chloride/acetate copolymer, unplasticised, lithographic, opaque
 to actinic light, transparent to optical light, thickness
 50 microns or less

POLYTETRAFLUOROETHYLENE PLANAR FORMS, adhesive backed

PLANAR FORMS, composed of polyethylene foam, coated on both sides
 with a pressure sensitive adhesive, thickness 0.8 mm or greater
 but NOT exceeding 1.5 mm

FILM, polyvinyl chloride, fluorescent, self-adhesive

POLYESTER FILM, having ALL of the following:
   (a) adhesive coated;
   (b) backed with a silicon release paper;
   (c) thickness NOT exceeding 0.4 mm,
 being packing supports for printing rollers

POLYESTER FILM (OTHER THAN metallised polyester film), coloured
 or textured, pressure sensitive adhesive backed, having EITHER
 of the following characteristics:
   (a) when applied to glass or plastic surfaces creates the
       appearance of stained glass or leadlight panes;
   (b) when applied to smooth plastic transparencies creates
       transparent colouring

POLYPROPYLENE PLANAR FORMS, in rolls, reinforced with glass
 filaments, pressure sensitive adhesive coated, having ALL of the
 following:
   (a) a breaking strength NOT exceeding 1 200 N/25 mm;
   (b) a width exceeding 500 mm;
   (c) a length NOT less than 45 m

PLANAR FORMS, composed of polyurethane, coated on both sides with
 pressure sensitive adhesive, having a thickness of 0.762 mm to
 6.350 mm (both inclusive)

SHEETING, reflective, incorporating or coated with glass beads,
 supported on a curl free release liner

POLYVINYL CHLORIDE FOAM, closed cell, in rolls having a width of
 1 143 mm or greater, being ANY of the following:
   (a) coated with a pressure sensitive acrylic adhesive on both
       sides;
   (b) coated with a pressure sensitive acrylic adhesive on one
       side and having a density of 250 kg/cu m or greater;
   (c) having a polyester film bonded to one side and a pressure
       sensitive acrylic adhesive coating on the other side

FILM, poly(methyl methacrylate), transparent, self-adhesive

FILM, polyvinyl chloride, adhesive coated, having a width 
greater than 20 cm

TAPES, self adhesive, single sided, PVC backing

SETS, SCREEN PROTECTOR, PHONE AND/OR COMPUTER AND/OR MOBILE 
MUSIC PLAYER AND/OR MOBILE VIDEO PLAYER, consisting of a plastic 
self-adhesive screen protector and NOT less than ANY two of the 
following combinations:
  (a) cleaning cloths;
  (b) smoothing cards;
  (c) back overlay protectors;
  (d) dust removal film

TAPE, PRINTING PLATE MOUNTING, polyethylene foam, in rolls, 
including ALL of the following:
  (a) coated on BOTH sides with a pressure sensitive adhesive;
  (b) having a release liner on one side;
  (c) width NOT less than 50 mm

SCREEN PROTECTORS, PHONE AND/OR COMPUTER AND/OR MOBILE VIDEO 
PLAYER AND/OR MOBILE MUSIC PLAYER, plastic, whether OR not 
including a cleaning cloth AND/OR screen smoothing card

TAPE, SEALING, POLYMERASE CHAIN REACTION, transparent, polyester 
OR polyolefin

FILM, PROTECTIVE COATING, polyethylene, resin AND/OR rubber     
self-adhesive

FILM, PROTECTIVE COATING, polyolefin, acrylic self-adhesive

FILM, BALING, COTTON PICKER, polyethylene, having ALL of the 
following:
  (a) width NOT less than 2 500 mm and NOT greater than 3 000 mm;
  (b) thickness NOT less than 70 microns and NOT greater than
      90 microns;
  (c) radio frequency identification tags;
  (d) adhesive strips;
  (e) individual wrap portions

POLYSTYRENE FOAM BOARD, having BOTH of the following: 
  (a) coated on one side with adhesive AND the other side
      with acid free paper;
  (b) thickness NOT less than 3 mm

FILM, polyolefin, in sheets OR rolls, having BOTH of the 
following:
  (a) adhesive backing;
  (b) release liner

STICKERS, in flat shapes, with or without printed text

FILM, POLYPROPYLENE, adhesive coated, having a width NOT less 
than 225 mm

FILM, POLYVINYLCHLORIDE (PVC), in sheets OR rolls, having BOTH  
of the following:
  (a) adhesive backing;
  (b) release liner

SHEETING, VINYL, in rolls, clear AND/OR coloured, having ALL of 
the following:
  (a) adhesive backing;
  (b) release liner;
  (c) width NOT less than 1 000 mm

TAPE, EXPANDING, self adhesive, polyurethane, in rolls

SHEET, POLYVINYL CHLORIDE, having BOTH of the following:
  (a) release liner;
  (b) glass fabric reinforcing layer

SHEETS, NON CELLULAR, high density polyethylene (HDPE), compressed
 heat laminated, multilayered, having ALL of the following:
   (a) minimum physical properties as follows:
         (i) thickness of 19 mm;
        (ii) density of 0.98 g/cu cm;
       (iii) tensile strength 3 900 psi;
   (b) non permeable;
   (c) UV stabilised

PROTECTIVE SHEETS, polyethylene, embossed, non cellular, having BOTH
 of the following:
   (a) a width NOT exceeding 2.6 m;
   (b) a length NOT exceeding 3.6 m

SHEETS, HDPE, having ALL the following:
   (a) fully pigmented with calcium carbonate;
   (b) having a permeability to water of less than 0.5 g/m DIN 53122
       at 23 degrees C and 85% relative atmospheric humidity

POLYETHYLENE FILM, high density oriented and cross laminated,
 having two or more layers of film in which the molecular
 orientation runs at 90 degrees to one another, whether or not clay
 coated or corona discharge treated

POLYETHYLENE WRAP SHEETING, imported in roll form of a width
 exceeding 4 720 mm

POLYETHYLENE FILM, linear low density, uncoated, unpigmented,
 unprinted, NOT corona discharge treated, conforming to ALL of the
 following specifications:
   (a) width 200 - 750 mm;
   (b) length NOT exceeding 1 000 m or an OD NOT exceeding 265 mm;
   (c) thickness 15 microns OR 20 microns;
   (d) a shrinkage factor of NOT less than 70% at 140 degrees C in
       BOTH machine and transverse directions;
   (e) tensile strength not less than 530 kg/cm2 in both machine
       and transverse directions
   (f) impact strength NOT less than 8.5 kg/cm2 in BOTH machine and
       transverse directions

SHEETS, polyethylene, high density, pervious, moulded, sintered

POLYETHYLENE SHEET, cast low density, embossed and coloured,
 whether or not printed

SEALING BAND RIBBONS, rolls, high-density polyethylene film

POLYETHYLENE FILMS, embossed AND/OR coloured, in rolls, having 
BOTH of the following:
  (a) roll width NOT less than 130 mm and NOT greater than 
      700 mm;
  (b) basis weight NOT less than 15 gsm and NOT greater than 
      22 gsm

STRETCH FILM, co-extruded polyolefin, having BOTH of the 
following:
  (a) repeating laser micro perforations of NOT greater than 
      52 micrometres;
  (b) complying with Regulation (EC) 1935/2004

SHRINK FILM, polyolefin, low-density polyethylene, having ALL of 
the following:
  (a) single wound;
  (b) thickness NOT greater than 12 microns;
  (c) shrinkage NOT less than 70% at 120 degrees Celsius

POLYETHYLENE SHEETS, ultra-high molecular weight, 
having ALL of the following:
  (a) density NOT less than 0.93 grams per cubic cm;
  (b) notched impact strength NOT less than 100 kJ per sq m;
  (c) elongation at break NOT less than 50 per cent;
  (d) tensile strength at yield NOT less than 17 Newtons;
  (e) length NOT less than 1 m;
  (f) width NOT less than 1 m and NOT greater than 4 m;
  (g) thickness NOT less than 3 mm and NOT greater than
      70 mm

FILMS, FOOD PACKAGING, having a thickness NOT less than 0.085 mm 
and NOT greater than 0.15 mm, being EITHER of the following 
compositions:
  (a) polyethylene AND ethylene vinyl alcohol; 
  (b) polyethylene AND polyamide AND polyethylene terephthalate

POLYETHYLENE SHEET, being ANY of the following:
  (a) high molecular weight polyethylene (HMWPE) sheet having
      a ball indentation hardness NOT less than 50 newtons 
      per square millimetre;
  (b) ultra high molecular weight polyethylene (UHMWPE) sheet
      having BOTH of the following:
           (i) notched impact strength NOT less than 140 kJ
               per square metre;
          (ii) elongation at break NOT less than 350 per cent,
  (c) ultra high molecular weight polyethylene (UHMWPE) sheet,   
      having ALL of the following:
           (i) density NOT less than 0.93 grams per cubic
               centimetre;
          (ii) notched impact strength NOT less than 150 kJ
               per square metre;
         (iii) elongation at break NOT less than 250 per cent;
          (iv) tensile strength at yield NOT less than 17
               newtons per square millimetre

POLYETHYLENE, in pressed sheets, ultra-high molecular weight,
having NOT less than 9 million molecular weight

SHEETS, LAMINATED, polyethylene having ALL of the following:
  (a) density NOT less than 900kg/m3;
  (b) one black and NOT less than one coloured layer;
  (c) thickness NOT less than 1.5 mm and NOT greater than 3.5 mm

FILM, LDPE AND EVA, in rolls, UV stabilised, having BOTH of the 
following:
  (a) thickness NOT greater than 200 micron;
  (b)  width NOT less than 5.5 m and NOT greater than 14 m

SHEETING, IN ROLLS, having ALL of the following:
  (a) base of rapier woven high density polyethylene fabric
      having BOTH of the following;
       (i)  yarn NOT less than 1 100 decitex;
       (ii) NOT less than 5 yarns in both warp and weft 
            directions per square centimetre; 
  (b) coated on both sides with low density polyethylene;
  (c) width NOT less than 2 600 mm;
  (d) weight NOT less than 170 grams per square metre

MEMBRANE SHEETS, linear low density polyethylene, in rolls, 
having ALL of the following: 
  (a) membrane density NOT greater than 0.94 grams per cubic 
      centimetre;
  (b) roll width NOT less than 7 metres;
  (c) roll length NOT greater than 280 metres;
  (d) membrane thickness NOT less than 0.75 mm and NOT
      greater than 4 mm;
  (e) smooth AND creaseless surface on both sides

MEMBRANE SHEETS, high density polyethylene, in rolls, having 
ALL of the following: 
  (a) membrane density NOT less than 0.94 grams per cubic 
      centimetre;
  (b) roll width NOT less than 7 metres;
  (c) roll length NOT greater than 280 metres;
  (d) membrane thickness NOT less than 0.75 mm and NOT
      greater than 4 mm;
  (e) smooth AND creaseless surface on both sides

MEMBRANE SHEETS, linear low density polyethylene, in rolls, 
having ALL of the following: 
  (a) membrane density NOT greater than 0.94 grams per cubic 
      centimetre;
  (b) roll width NOT less than 7 metres;
  (c) roll length NOT greater than 280 metres;
  (d) membrane thickness NOT less than 0.75 mm and NOT
      greater than 4 mm;
  (e) elongation at break NOT less than 350 per cent;
  (f) tensile strength at break NOT less than 17 newtons
      per square millimetre;
  (g) patterned AND structured surface on at least one side

MEMBRANE SHEETS, high density polyethylene, in rolls, having 
ALL of the following: 
  (a) membrane density NOT less than 0.94 grams per cubic 
      centimetre;
  (b) roll width NOT less than 7 metres;
  (c) roll length NOT greater than 280 metres;
  (d) membrane thickness NOT less than 0.75 mm and NOT
      greater than 4 mm;
  (e) elongation at break NOT less than 350 per cent;
  (f) tensile strength at break NOT less than 17 newtons
      per square millimetre;
  (g) a patterned AND structured surface on at least one side

FILM, plastic, multi-layered, having ALL of the following:
  (a) polyethylene OR ethylene-vinyl acetate co-polymer
      core layer;
  (b) polyethylene outer layers;
  (c) combined multi-layered film thickness NOT less than 20
      micron and NOT greater than 60 micron;
  (d) circumference capacity NOT less than 1 600 mm and NOT
      greater than 6 800 mm;
  (e) maximum stretching capacity NOT less than 10% and NOT
      greater than 120%

FILM, plastic, 9 layered co-extruded, having a thickness NOT 
less than 90 um and NOT greater than 150 um

GEOMEMBRANES, low density polyethylene, in rolls, having 
ALL of the following:
  (a) width NOT less than 7 m;
  (b) length NOT less than 50 m;
  (c) thickness NOT less than 0.75 mm and NOT greater than 3.0 mm

GEOMEMBRANES, high density polyethylene, in rolls, having 
ALL of the following:
  (a) width NOT less than 7 m;
  (b) length NOT less than 50 m;
  (c) thickness NOT less than 0.75 mm and NOT greater than 3.0 mm

MEMBRANE, low density polyethylene, in rolls, having ALL of the 
following:
  (a) width NOT less than 2 metres;
  (b) length NOT less than 10 metres;
  (c) thickness NOT less than 2 mm

LOW DENSITY POLYETHYLENE (LDPE) FILM, embossed

LOW DENSITY POLYETHYLENE (LDPE) FILM, in rolls, having ALL of 
the following:
  (a) thickness NOT less than 6.5 microns and NOT greater than  
      10.5 microns;
  (b) film width NOT greater than 440 mm;
  (c) length NOT less than 400 m and NOT greater than 3 500 m;
  (d) film weight NOT less than 1.9 kg and NOT greater 
      than 13.8 kg;
  (e) laps on each edge;
  (f) pre-stretched

FILM, linear low density polyethylene, having BOTH of the 
following:
  (a)  thickness NOT less than 250 micron;
  (b)  width NOT less than 3 m

DROP SHEETS, polyethylene

LINING MATERIALS, polyethylene, high density, acid resistant, 
being
 ANY of the following forms:
   (a) wall screed guides;
   (b) screed strips;
   (c) pre-fabricated forms;
   (d) h-zip strips

FILM, low density polyethylene, embossed AND siliconised

FILM, MOLECULAR BINDING, heat induced, ethylene vinyl acetate

FILM, polyethylene, in rolls, 3 layer co-extruded, UV 
stabilised, having BOTH of the following:
  (a) width NOT less than 4 m and NOT greater than 13 m;
  (b) thickness not less than 100 micrometre and not greater than
      250 micrometre

FILM, polyethylene, in rolls, having a width NOT less 
than 10 000 mm

SHEETS, PROTECTIVE STERILE FIELD, polyethylene

FILM, POLYETHYLENE, in rolls in serrated edged packages, having 
ALL of the following:
  (a) thickness NOT less than 9 microns and NOT greater than 20
      microns;
  (b) width NOT greater than 45 cm;
  (c) length NOT greater than 600 m

GEOMEMBRANES, ethylene vinyl acetate, in rolls, having BOTH the 
following:
  (a) width NOT less than than 6.5 metres;
  (b) thickness NOT less than 0.50 mm and NOT greater than 3.0 mm

FILM, POLYETHYLENE, in rolls in serrated edged packages, having 
ALL of the following:
  (a) thickness NOT less than 9 microns and NOT greater than 12
      microns;
  (b) width NOT greater than 38 cm;
  (c) length NOT greater than 150 m

FILM, POLYETHYLENE, in rolls in serrated edged packages, having 
ALL of the following:
  (a) thickness NOT less than 9 microns and NOT greater than 12 
      microns;
  (b) width NOT greater than 33 cm;
  (c) length NOT greater than 30 m

SHEETS, PROTECTIVE, STERILE, polyethylene, having ALL of the 
following:
  (a) width NOT greater than 150 cm;
  (b) length NOT greater than 220 cm;
  (c) thickness NOT greater than 45 micron

POLYETHYLENE FILM, linear low density, breathable, calcium carbonate

SHEETING, high density polyethylene, having BOTH of the following:
   (a) specific gravity NOT less than 0.94 at 20 degrees Celsius;
   (b) thickness NOT less than 7 mm

SYNTHETIC PAPER, biaxially oriented polyethylene, clay coated

SHRINK FILM, POLYOLEFIN, multi-layer, having ALL of the
 following:
   (a) single wound OR centre folded;
   (b) thickness NOT less than 11 microns and NOT greater
       than 35 microns;
   (c) yield (m2/kg) NOT less than 43.5 m2/kg and NOT greater
       than 100 m2/kg;
   (d) shrinkage NOT less than 50% and NOT greater than 75% at
       120 degrees C;
   (e) haze of less than 4%

POLYETHYLENE FILM, 5 layer, co-extruded, thermoformable, low
 density, having BOTH of the following:
   (a) width NOT exceeding 2 100 mm;
   (b) thickness NOT exceeding 100 microns;

SEALING STRIP, ASEPTIC JUICE AND DAIRY PACKAGE, multi layer, heat
 sealing

POLYPROPYLENE PLANAR FORMS, having a thickness NOT less than 9 mm

LINING MATERIALS, polypropylene, acid resistant, being ANY of the
 following:
   (a) sheets;
   (b) wall screed guides;
   (c) screed strips;
   (d) pre-fabricated forms;
   (e) connecting strips

FILM, polypropylene, clear, biaxially oriented, two sides corona-
 treated, one side heat-activated adhesive coated, having BOTH of the
 following:
   (a) thickness of 15 microns or greater;
   (b) width of 200 mm OR greater but NOT exceeding 1 250 mm,
 but NOT including polypropylene film coated on one side with
 pressure sensitive adhesive with or without a protective removable
 liner

FILM, polypropylene, thickness of 7 microns or greater, having a
 full colour ink jet printer coating, but NOT including ANY of the
 following:
   (a) heat sealable by impulse or hot bar method;
   (b) printed;
   (c) having ink and pencil receptive transparent and/or opaque
       coatings (ie. drafting film);
   (d) adhesive coated

POLYPROPYLENE BOARDS, planed surface, thickness 4 - 50 mm

FILM, polypropylene, in rolls, biaxially oriented, not pigmented
 or printed, having BOTH of the following:
   (a) thickness NO greater than 20 microns;
   (b) matte-delustred surface

PAPER, SYNTHETIC, biaxially orientated polypropylene, having ALL 
of the following:
  (a) clay coating on both sides;
  (b) matt finish;
  (c) weight NOT less than 80 g/m2 and NOT greater than 175gsm;
  (d) thickness NOT less than 100um and NOT greater than 250um

FILM, POLYPROPYLENE HOMOPOLYMER, on reels, having ALL of the 
following:
  (a) thickness NOT less than 550 microns and NOT greater than 
      650 microns;
  (b) density NOT less than 0.9 g/cm3;
  (c) width NOT less than 270 mm;
  (d) melt flow index NOT less than 4.5g/10 mins

LABEL PRINT CARRIER FILM, adhesive, having ALL of the following;
  (a) NOT less than one side coated with a acrylic print 
      receptive layer having a thickness NOT less than 0.8 
      micrometres and NOT greater than 3.00 micrometres;
  (b) one side corona treated bi-axially orientated 
      polypropylene;
  (c) density NOT less than 0.67g/cmú

PAPER, polypropylene, in rolls, having ALL of the following:
  (a) thickness NOT less 180 microns and NOT greater than 
      263 microns;
  (b) weight NOT less than 144 gsm and NOT greater than 250 gsm

SHEETS, co-extruded polypropylene, in rolls, having ALL of the 
following:
  (a) total layered sheet composition NOT less than 70%
      polypropylene;
  (b) polyethylene layer, with OR without an ethylene vinyl
      alcohol(EVOH) layer;
  (c) sheet width NOT greater than 1 250 mm

FILMS, THERMAL LAMINATING, polypropylene based

STRAPPING, polypropylene, having BOTH of the following: 
  (a) width NOT less than 4.0 mm;
  (b) thickness NOT less than 0.38 mm

POLYPROPYLENE FILM, CAST, uncoated, humidity resistant, 
transparent, having ALL of the following:
  (a) both sides heat sealable AND corona treated;
  (b) thickness NOT less than 30 microns and NOT greater than 
      65 microns;
  (c) width NOT greater than 1 000 mm

PAPER, SYNTHETIC, biaxially oriented polypropylene, in rolls, 
having ALL of the following:
  (a) thickness greater than 77 microns;
  (b) density NOT less than 0.76 grams per cubic metre;
  (c) opacity greater than 88%

SHEETS, NON VULCANISABLE THERMOPLASTIC POLYOLEFIN, grain finish 
on one side, in rolls, thickness NOT less than 0.5 mm and NOT 
greater than 1.5 mm

POLYPROPYLENE, PLANAR FILM, rigid, having BOTH of the following:
  (a) thickness NOT less than 300 microns and NOT greater than
      1 000 microns;
  (b) fine crystalline and/or amorphous middle layer

PAPER, SYNTHETIC, biaxially orientated polypropylene, having ALL 
of the following:
(a) gauge NOT less than 90 microns;
(b) density NOT less than 0.77g/cm3;
(c) NOT less than one external surface containing calcium 
    carbonate and/or titanium dioxide

POLYPROPYLENE FILM, CAST, having BOTH of the following:
  (a) width NOT less than 180 mm;
  (b) thickness NOT less than 100 microns

FILM, plastic, multilayered, in rolls, having ALL of the 
following:
  (a) adhesive bonded polystyrene AND polyethylene AND ethylene
      vinyl alcohol layers;
  (b) co-extruded removable polypropylene layer on
      polyethylene layer;
  (c) width NOT less than 300 mm

FILM, polystyrene, having BOTH of the following:
  (a) biaxially oriented;
  (b) thickness NOT less than 20 microns and NOT greater than 40
      microns

FILM, BOTTOM WEB THERMOFORM, in rolls, multi-layered, having ALL 
of the following:
  (a) polystyrene top AND bottom layer;
  (b) polyethylene middle layer;
  (c) thickness NOT greater than 800 microns

SHEETS, BINARY-ORIENTED POLYSTYRENE

POLYVINYL CHLORIDE FOIL, plasticised, printed, having thickness 
NOT greater than 0.20 mm +/- 10%

SHEETING, having ALL of the following:
  (a) polyester sheet reinforcement; 
  (b) laminated or coated on both sides with polyvinyl chloride;
  (c) width NOT less than 100 cm and NOT greater than 510 cm;
  (d) weight NOT less than 200 grams per square metre and NOT 
      greater than 1 300 grams per square metre

SHEETS AND/OR FILMS, polyvinyl chloride, plasticized

SHEETS AND/OR FILMS, polyvinyl chloride, plasticised, transparent

SHEETS, POLYVINYL CHLORIDE, extruded, thickness NOT less than 
1.5 mm

POLYVINYL CHLORIDE PLANNAR FORMS, plasticised, transparent,
 uncoloured, having a thickness NOT greater than 0.45 mm

POLYVINYL CHLORIDE FILM, monoaxially oriented in the transverse
 direction, having ALL of the following:
   (a) thickness  NOT exceeding 75 microns;
   (b) transverse shrink capacity exceeding 45%;
   (c) start of shrink 40 to 60 degrees Celsius

PVC, BEVELLED EDGED STRIP, having ALL of the following:
   (a) clear;
   (b) U.V. stablized;
   (c) 50 metre rolls in width range of 95mm to 400mm both inclusive;
   (d) in thickness range of .95mm to 4.5mm BOTH inclusive

POLYVINYL CHLORIDE FILM, monoaxially orientated in transverse
 direction, having ALL of the following:
   (a) thickness - 40, 50 or 75 microns;
   (b) shrink capacity for shrink sleeves:
         (i) longitudinal - max. 6%;
        (ii) transverse - approx 52 +/- 3%
   (c) start of shrink - approx. 60 degrees C

RETROREFLECTIVE MATERIAL, having CIL values for the relevant
 chromaticity co-ordinates NOT less than those specified in
 AS1906, AS2142 or AS2259

POLYVINYL CHLORIDE PLANAR FORMS, plasticised, transparent, clear,
 uncoloured, having a thickness NOT less than 0.45 mm

POLYVINYL CHLORIDE FILM, having BOTH of the following:
   (a) thickness of 2 mm or greater but NOT exceeding 10 mm;
   (b) transparent

POLYVINYL CHLORIDE SHEETING, microprism retro-reflective

FOIL, multilayer, in rolls, having ALL of the following:
  (a) polyvinyl chloride base;
  (b) polyethylene middle layer;
  (c) polyvinylidene chloride top coating;
  (d) thickness NOT less than 200 microns and NOT greater than 
      500 microns

SHEETING, polyvinyl chloride, flocked on one side OR both sides, 
in rolls, having BOTH of the following:
  (a) width NOT less than 650 mm;
  (b) thickness NOT less than 0.17 mm

SHEETS AND/OR FILM, POLYVINYL CHLORIDE, coloured AND/OR printed, 
having a thickness NOT less than 0.25 mm

SHEETS AND/OR FILMS, polyvinyl chloride, plasticised, having a 
thickness NOT less than 0.45 mm

SHEETS, PVC, IN ROLLS, having BOTH of the following:
  (a) thickness NOT less than 300 microns and NOT greater
      than 500 microns;
  (b) width NOT greater than 1 400 mm

POLYVINYL CHLORIDE FILM, unplasticised

POLYVINYL CHLORIDE PLANAR FORMS, unplasticised, polished surface
 on both sides, thickness 0.17 mm or greater but NOT exceeding
 1.00 mm, coated with polyvinylidene chloride

SHEETS, poly (methyl methacrylate), co-extruded, having 
ALL of the following:
  (a) coloured layer substrate NOT less than 10% of total
      thickness;
  (b) coated with gloss ultra violet cured plastic blend
      film layer having ANY of the following: 
          (i) film hardness NOT less than 4H pencil hardness; 
         (ii) film density NOT less than 1.06 g/cm3 at 
              23 degrees C; 
        (iii) colour fastness NOT exceeding Delta E 1.8, 
  (c) length NOT less than 1 800 mm;
  (d) width NOT less than 700 mm; 
  (e) thickness NOT greater than 8.0 mm

SHEETS, cast acrylic, having a thickness NOT greater than 
17 mm

SHEETS, RESIN, thickness NOT less than 12 mm and NOT greater 
than 30 mm, consisting of ALL of the following:
  (a) methyl methacrylate;
  (b) aluminium trihydrate;
  (c) catalysts and pigments stabilisers

SHEETS, hydrated alumina filled solid surface, having ALL of 
the following:
  (a) sheet thickness 6.00 mm OR 12.00 mm OR 19.00 mm;
  (b) acrylic polymer content NOT less than 40% and NOT greater
      than 45%;
  (c) hydrated alumina content NOT less than 55% and NOT greater
      than 60%
For the purpose of this Order, tolerances for (a) sheet 
thickness are +/- 5%

SHEETS, PLASTIC, polymethyl methacrylate, co-extruded, having 
ALL of the following:
  (a) coloured layer substrate greater than 10% of total 
      thickness;
  (b) coated with gloss ultra violet (UV) cured plastic blend
      film layer, having a  hardness complying with the standard
      test method for film hardness using 4H pencil hardness OR
      greater in American Society for Testing and Materials 
      ASTM D 3363-05;
  (c) length NOT less than 1 800 mm;
  (d) width NOT less than 700 mm;
  (e) thickness NOT less than 2 mm and NOT greater than 8 mm

MIRROR, clear acrylic

FOIL, multi-layer, in rolls, whether or NOT embossed, having ALL 
of the following:
  (a) UV stabilised PVC;
  (b) semi rigid base film;
  (c) acrylic top film

SHEETS, polycarbonate, extruded, having ALL of the following:
  (a) thickness NOT less than 3 mm and NOT greater than 15 mm;
  (b) polysiloxane hard coating on both sides; 
  (c) taber abrasion haze NOT greater than 4%

FILM, POLYCARBONATE, hydrophilic coated

POLYETHYLENE TEREPHTHALATE FILM, having BOTH of the following:
   (a) coated on one or both sides with a complex of polyethylene
       resin and finely dispersed silica;
   (b) thickness of base film NOT less than 25 microns but NOT
       exceeding 350 microns

POLYETHYLENE TEREPHTHALATE FILM having ALL of the following:
   (a) thickness of less than 350 microns;
   (b) width greater than 450 mm;
   (c) ink, pencil and printing receptive coatings being opaque or
       transparent

POLYETHYLENE TEREPHTHALATE FILM, having BOTH of the following:
   (a) coated on one or both sides with a complex of
       styrene-acrylic ester copolymer and colloidalsilica;
   (b) thickness of base film NOT less than 25 microns but NOT
       exceeding 350 microns

POLYETHYLENE TEREPHTHALATE FILM, having BOTH of the following:
   (a) coated on one side with translucent hydrophilic lacquer
       and on the reverse side with translucent hydrophobic lacquer;
   (b) thickness of base film NOT less than 50 microns but NOT
       exceeding 350 microns

POLYETHYLENE TEREPHTHALATE FILM, having a thickness of 7 microns
 or greater but NOT exceeding 350 microns, but NOT including ANY
 of the following:
   (a) having ink and pencil receptive transparent AND/OR opaque
       coatings (ie. drafting film);
   (b) heat sealable by impulse OR hot bar method having a
       thickness less than 15 microns;
   (c) adhesive coated, whether pressure sensitive OR heat
       reactivated;
   (d) coated copying film;
   (e) metallised;
   (f) printed

FILM, WINDOW, polyester, transparent

POLYETHYLENE TEREPHTHALATE FILM, biaxially orientated, one side
 heat-activated polyethylene copolymer adhesive coated, two sides
 corona treated, having BOTH of the following:
  (a) thickness of base film NOT less than 9 microns but NOT
      exceeding 200 microns;
  (b) thickness of adhesive layer NOT less than 21 microns but NOT
      exceeding 88 microns

FILM, POLYETHYLENE TEREPHTHALATE, bonded, having all of the
 following:
   (a) one membrane, 10 microns thickness or greater, being either
       unoriented or biaxially oriented polyester;
   (b) bonded with a co-polymer polyethylene resin 15 microns
       thickness or greater

POLYETHYLENE TEREPHTHALATE FILM, having a thickness of 7 microns
 or greater but NOT including ANY of the following:
   (a) heat sealable by impulse or hot bar method having a
       thickness less than 15 microns;
   (b) adhesive coated, whether pressure sensitive or heat
       reactivated;
   (c) coated copying film;
   (d) metallised;
   (e) printed

STRAP, polyester, smooth embossed, of a width ranging from
 8.62 mm to 12.2 mm (both inclusive), thickness ranging from
 0.50 mm to 0.73 mm (both inclusive), breakstrength
 ranging from 1.780 kN to 3.700 kN (both inclusive) and
 elongation ranging from 5% to 20% (both inclusive)

SYNTHETIC PAPER, DIGITAL LASER PRINTING, having ALL of the 
following:
  (a) polyethylene terephthalate core having a barium sulphate 
      content NOT greater than 2.5 per cent;
  (b) matt coating on both sides;
  (c) thickness NOT less than 95 microns

FILM, polyethylene terephthalate, having ALL of the 
following:
  (a) thickness NOT less than 50 microns; 
  (b) in rolls having a diameter NOT less than 470 mm;
  (c) biaxially oriented

FILM, THERMAL TRANSFER PRINTING AND LAMINATION, having BOTH of 
the following:
  (a) NOT less than 65% polyethylene terephthalate (PET);
  (b) coloured OR holographic

FILM, polyethylene terephthalate glycol, high shrinkage

FILM, polyethylene terephthalate (PET), biaxially oriented, 
having ALL of the following:
  (a) one surface acrylic coated;
  (b) one surface corona treated;
  (c) thickness NOT less than 7 microns

SHEETING, recycled polyethylene terephthalate (rPET), in rolls, 
complying with Australian Standard AS 2070-1999, 4.1 OR 4.2, 
having ALL of the following:
  (a) width NOT less than 400 mm and NOT greater than 800 mm;
  (b) sheet thickness NOT less than 400 microns and NOT greater
      than 700 microns;
  (c) sheet laminate thickness NOT less than 20 microns;
  (d) heavy metal content NOT greater than 100 ppm

FILM, THERMAL PRINTING AND LAMINATION, in rolls OR sheets, 
transparent, having a composition of NOT less than 70% 
polyethylene terephthalate (PET)

FILM, POLYESTER, having ALL of the following:
  (a) polypropylene terephthalate glycol (PETG) sealing layer;
  (b) oriented polypropylene (OPP) base layer;
  (c) oxygen barrier layer;
  (d) thickness less than 45 microns;
  (e) anti-fog treatment

FILM, polyethylene terephthalate, metallised, amorphous, having 
BOTH of the following:
  (a) width NOT less than 600 mm;
  (b) thickness NOT greater than 12 microns

FILM, POLYETHYLENE TEREPHTHALATE (PET), pre-siliconised, in 
rolls, having BOTH of the following:
  (a) thickness NOT less than 10 micron and NOT greater than
      40 micron;
  (b) tensile strength NOT less than 1 700 kg/cm2

FILM, plastic, multi-layered, including ALL of the following:
  (a) polyvinyl fluoride film layer;
  (b) polyethylene terephthalate film layer;
  (c) adhesive layers;
  (d) combined multi-layered film thickness NOT less than 
      0.30 mm and NOT greater than 0.36 mm

THERMAL FILM, polyethylene terephthalate, dyed AND/OR surface 
coated, having BOTH of the following:
  (a) width NOT less than 1 000 mm;
  (b) thickness NOT less than 10 micron and NOT greater than 200
      micron

LAMINATING FILM, POLYESTER, in rolls OR pouches, having a
 co-extruded adhesive coating

SHEETS, RESIN, thickness NOT less than 12 mm and NOT greater 
than 30 mm, consisting of ALL of the following:
  (a) maleic anhydride;
  (b) aluminium trihydrate;
  (c) catalysts and pigments stabilisers

POLYESTER FILM, GLASS LAMINATING

PLOTTING FILMS, having ALL of the following characteristics:
   (a) clear or matte surface (single or double sided);
   (b) sheets, rolls or fanfold;
   (c) caliper range 0.0508 mm to 0.1778 mm;
   (d) dielectric, anti static or water based coating

POLYVINYL BUTYRAL

NYLON STRAPPING

NYLON PLANAR FORMS, width exceeding 280 mm

FILM, NYLON, polyvinyl dichloride (PVDC) coated

SHEETS, JOINTING, compressed aramid fibre

FILM, stencil, screen process printing

POLYURETHANE FILM, thickness NOT exceeding 0.9 mm

POLYIMIDE FILM

POLYTETRAFLUOROETHYLENE TAPE, width 750 mm or greater but
 NOT exceeding 1 230 mm

FILM, fluorinated ethylene-propylene

BLADES, SQUEEGEE, SCREEN-PRINTING, urethane, non-chamfered edged

WRAPS, having BOTH of the following:
  (a) polyisobutene;
  (b) polyolefin carrier film AND polyolefin mesh

MEMBRANES, polyether ether ketone, anion exchange

FILM, polyurethane, in rolls, having BOTH of the following:
  (a) heat activated transfer;
  (b) PET liner

SHEETS, MODIFIED POLYTETRAFLUROETHYLENE (PTFE), incorporating 
one OR more of the following:
  (a) silicon carbide;
  (b) inorganic fillers;
  (c) barium sulphate;
  (d) glass microspheres

FILM, multi-layered, having ALL of the following:
  (a) polyamide layer;
  (b) polyethylene terephthalate layer;
  (c) ethylene vinyl alcohol layer;
  (d) polyethylene layer 
with OR without starch powder

BRICKS, INTUMESCENT

SHEETS, plastic, multi-layer, having BOTH of the following:
  (a) imitation leather embossed thermoplastic polyurethane top
      layer;     
  (b) thickness NOT less than 2 mm and NOT greater than 6 mm

FILM, collagen, edible

FILM, multi-layer, consisting of polyester and polyethylene 
vinyl alcohol, having a width NOT greater than 500 cm

FILM, breathable, hydrophilic, having a thickness NOT less than 
3 micrometres and NOT greater than 9 micrometres

POLYURETHANE FILM, thickness NOT exceeding 1.30 mm

TIMBER, SYNTHETIC

FOAM, POLYSTYRENE, having BOTH of the following:
   a) one side coated with torque-activated adhesives;
   b) thickness NOT greater than 0.7 mm

POLYSTYRENE FOAM BOARDS, covered on both sides with a clay coated
 paper

MOUNTING BOARDS, being polystyrene foam board laminated both
 sides with acid free uncoated paper

POLYVINYL CHLORIDE FOAM, closed cell, in rolls conforming to
 ASTM D1056 compression deflection test Grade RE41 or RE42

SHEET, SPONGE, PVC, having ALL of the following:
   (a) sponge centre;
   (b) PVC covering;
   (c) textile backing

SHEET, polyvinyl chloride cellular foam, moulded pattern in relief,
 having ALL of the following:
 (a) thickness in excess of 2 mm;
 (b) width 120 mm to 140 mm;
 (c) heat resistant;
 (d) 100% polyester non woven fibre backing;
 (e) depth of pattern NOT less than 0.6 mm

SHEETS, foam, polyvinyl chloride

FOAM, POLYVINYL CHLORIDE(PVC), OPEN CELL

SHEETS, POLYVINYL CHLORIDE (PVC), foam, extruded

CONVEYOR BELTS, single ply polyester fabric, polyurethane
 impregnated such that the impregnation is visible from both sides
 with the naked eye, having a thickness of less than 3 mm and a
 width exceeding 1.2 m

FOOTWEAR LINING MATERIAL, polyurethane top coated, non woven or
 polyurethane impregnated woven base fabric

POLYURETHANE/POLYESTER HOMOGENEOUS SHEETING, being a polymer blend
 having ALL the following characteristics:
   (a) non porous surface;
   (b) width 1 500 mm;
   (c) thickness range 1-5 mm

FLEXIBLE POLYESTER POLYURETHANE FOAM, being isocyanate based, NOT
 containing aromatic (benzenic) rings, resistant to yellowing under
 direct light

FOAM, foot impression, for the fabrication of arch supports

SLEEPER PADS, RAIL, being single layer cellular polyurethane 
elastomers

SUB-BALLAST MATS, RAILWAY TRACK, closed AND/OR mixed cellular 
polyurethane elastomer, multi-layered, having ANY of the 
following:
  (a) geotextile OR fleece load distribution layer;
  (b) microcellular polyurethane resilient layer

UNDER-SLEEPER PADS, RAILWAY TRACK, including BOTH of the 
following:
  (a) two OR more layers;
  (b) elastoplastic AND/OR cellular polyurethane layer,
with OR without EITHER of the following:
            (i) polyamide mesh AND/OR mounting mesh;
           (ii) geotextile polyurethane layer

SUB-BALLAST MATS, RAILWAY TRACK, closed cellular polyurethane 
elastomer, multi-layered, having BOTH the following:
  (a) geotextile OR fleece load distribution layer;
  (b) microcellular polyurethane resilient layer

FILM, POLYURETHANE, heat sealable

REGENERATED CELLULOSE VEGETAL MATERIAL, cut to a finished size

MOP REFILLS, being regenerated cellulose sponge with plastic 
mounts

SPONGES, regenerated cellulose, cut to size and shape

ETHYLENE VINYL ACETATE SHEETING, being footwear soling material,
 having ALL of the following:
   (a) sheet sizes NOT less than 280 mm x 850 mm;
   (b) a flat surface on one side and a moulded surface on the other
       side being either grooved, patterned, rippled, checked, weave
       or crepe;
   (c) sheet profile either wedge, taper or step;
   (d) profile thickness at toe point NOT less than 3 mm and NOT
       greater than 20 mm, at heel point NOT less than 5 mm and NOT
       greater than 50 mm

POLYETHYLENE SHEET, beaded type crosslinked moldable foam, high
 density and tensile strength, completely water and chemical
 resistant, light weight, buoyant, shapable and able to be laminated

ETHYLENE VINYL ACETATE SHEETING, cellular, being footwear soling
 material having a flat surface on one side and a moulded surface on
 the other, being either grooved, patterned, rippled, checked, weave
 or crepe

SHEETS, FOAM, polyethylene terephthalate (PET), rigid planar form

PANELS, INSULATING, polyisocyanurate (PIR) core, steel faced

FOAM, open cell, melamine resin, in blocks AND/OR sheets

FOAM, PHENOLIC, WATER ABSORBENT

POLYETHYLENE TAPE, low density, having ALL of the following:
  (a) Polyvinylidene Chloride (PVDC) laminated;
  (b) thickness NOT greater than 2 mm

SHEETS, POLYPROPYLENE HONEYCOMBS, incorporating needle punched 
fibreglass scrim on both sides

GLASS FIBRE FABRIC, coated with polytetrafluoroethylene

NYLON PLANAR FORMS, width exceeding 280 mm

POLYESTER FABRIC, covered with polyvinyl fluoride or
 polyvinylidene fluoride

COUNTER OR TOE PUFF STIFFENER MATERIAL, footwear, thermoplastic

INSULATING SHEETING, glass mat reinforced polyester laminate,
 having a thermal rating of 180 degrees C or greater based on
 ASTM D1830 Curved Electrode Test

SHEETING, reflective, incorporating or coated with glass beads,
 heat sensitive adhesive coated, supported on a curl free release
 liner

MEMBRANES, ion exchange

POLYESTER FILAMENT TAPE, hot melt adhesive coated

FABRIC, SAILCLOTH, laminated both sides

FILM, WINDOW, polyester, transparent

POLYETHYLENE SHEET, reinforced with polyester fibre, having rubber
 eyelets or polyester webbing, in widths exceeding 1.8 m, but NOT
 including sheet or tarpaulin as follows:
   (a) which have double rows of eyelets across the width of the roll
       at 3 m, 4 m or 5 m intervals; OR
   (b) which incorporate an emergency service symbol

CONVEYOR BELTING, one OR two ply construction, antistatic, having
 ALL of the following characteristics:
   (a) capable of operation around live or fixed knife edges with
       radius from 3-8mm;
   (b) urethane impregnated on top surface and on the underside;
   (c) base fabric constructed of:
       (i)  polyester mono filament weft;
       (ii) polyester multi filament warp;
   (d) belt thickness of:
       (i)  2 ply belts, maximum thickness 1.2 mm and minimum
            thickness 1 mm (both + or - 10%);
       (ii) 1 ply belts, 0.9 mm (+ or - 10%);
   (e) Food and Drug Administration approved for unwrapped foodstuffs

FILM, polyester, coloured, in rolls having ALL of the
 following characteristics:
   (a) heat activated dry glue base;
   (b) heat shrinkable

CONVEYOR BELTING, one or two ply construction, capable of operation
 around live or fixed knife edges with radius from 3-8 mm, having ALL
 of the following:
   (a) a 0.2 mm top surface of polyurethane;
   (b) urethane impregnated underside;
   (c) base fabric constructed of:
       (i)  polyester mono filament weft; and
       (ii) polyester multi filament warp

CURTAIN SIDE FABRIC, 2 x 2 panama weave polyester base fabric coated
 on both sides with polyvinyl chloride (PVC), having ALL of the
 following characteristics:
   (a) minimum width: 300cm;
   (b) acrylic lacquered on both sides;
   (c) minimum weight: 850 g/sq m;
   (d) flame retarded but not sufficient to satisfy the requirement
       of class C1.10 of the building code of Australia;
   (e) minimum breaking force of 4 000N/50 mm warp and 3 000N/50 mm
       weft, tested to AWTA Rapitest No. 9, method: C (cut strip)
       AS method modified; and
   (f) minimum tear resistance of 1 000N warp and weft tested to
       BS3424.5 1982, method 7B

POLYURETHANE OR POLYESTER HOMOGENEOUS CONVEYOR BELTING, non-
 fibrous, non-woven, solid extruded construction, in rolls,
 having ALL the following characteristics:
   (a) non porous surface;
   (b) width, up to 1 900 mm;
   (c) thickness range 2-5 mm

WRAP AROUND PIPE SLEEVE, having ALL of the following:
   (a) sheet material consisting of a radiation cross linked
       polyolefin backing;
   (b) minimum shrinkage of 28% when heated to above 130 degrees C;
   (c) coated with mastic or adhesive sealant

CONVEYOR BELTING, having ALL of the following:
   (a) a .2 mm top surface of polyurethane;
   (b) a two ply, polyurethane impregnated, base fabric constructed
       of:
         (i) polyurethane monofilament warp;
        (ii) polyester filament weft;
       (iii) an antistatic carbon fibre interwoven with the weft
             fibres of the inner ply base fabric

PAPER LAMINATE DRILL ENTRY BOARD, being of low clay content kraft,
 impregnated with phenolic and bonded under heat pressure to form a
 laminate

CURTAIN SIDE FABRIC, 2 x 2 panama woven, polyester, polyvinyl
 chloride coated both sides, having ALL of the following
 characteristics:-
   (a) minimum width 285 cm;
   (b) acrylic lacquered;
   (c) minimum total weight 850 gsm;
   (d) minimum thickness 0.7 mm;
   (e) flame retarded to DIN 75200 (flame speed 100 mm/min) but not
       sufficient to satisfy the requirements of class Cl.10 of the
       Building Code of Australia;
   (f) weld adhesion of 90 N/5 cm or greater, being strong enough
       for weld buckles or reinforcements;
   (g) minimum tensile strength of 4 000 N/5 cm warp and weft, tested
       to DIn 53354;
   (h) minimum tear resistance of 400 N warp and weft tested to
       DIN 53363

SOLING MATERIAL, footwear, polyurethane sheet - laminated with
 synthetic rubber in any of the following surfaces:
   (a) high gloss plain;
   (b) high gloss printed or patterned;
   (c) lacquered surface plain;
   (d) lacquered surface printed or patterned;
   (e) non-finished plain;
   (f) non-finished printed or patterned

FILM, cast polyvinyl chloride, but NOT including film manufactured
 by the calendered method, having ALL of the following:
   (a) film thickness not exceeding 0.06 MM (exclusing adhesive);
   (b) release liner;
   (c) elongation of less than 150% in accordance with ASTM
       method D1000-88;
   (d) pressure activated adhesive coating

EPOXY GLASS RIGID LAMINATED SHEETS, being a woven fibreglass
 cloth impregnated with epoxy resin, conforming to NEMA
 specification LI 1 Grade G11 (Class H), having the capacity to
 maintain mechanical strength when subjected to continuous
 temperatures in excess of 180 Degrees Centigrade

FIBRE-REINFORCED PLASTIC PANELS, having ALL of the following:
  (a) panel thickness NOT greater than 6.3 mm;
  (b) fire resistance complying with American Society for 
      Testing and  Materials standard E119-16a for 20 minutes 
      (ASTM E119-16a);
  (c) plastic water absorption conforming to ISO 62-2008, tested 
      in accordance with International Standard (ISO) 62-2008

MEMBRANES, WATERPROOFING, thermoplastic, including ALL of the 
following:
  (a) thermoplastic top AND bottom outer layer;
  (b) active polymer inner core;
  (c) reinforced woven polyester scrim;
  (d) thermoplastic membrane with non-welded seams

FILM, polyethylene terephthalate (PET) polyester, in rolls OR 
sheets, having a linear saturated co-polyester coating on one 
side

THERMO ADHESIVE STRIPS, in spools, having BOTH of the following:
  (a) laminated PET;
  (b) extruded LPDE

FILM, cross laminated high density polyethylene, having BOTH of 
the following:
  (a) offset printable AND/OR thermal transfer printable AND/OR  
      flexography printable sides;
  (b) in rolls

FILM, biaxially oriented polypropylene, printed, in rolls, 
having BOTH of the following:
  (a) re-sealable rubber latex coating;
  (b) width NOT less than 230 mm and NOT greater than 250 mm

FILM, paper AND polypropylene (PP), having ALL of the following:
  (a) weight NOT less than 144 g per square metre;
  (b) polypropylene(PP) layer thickness NOT less than 140 microns
      and NOT greater than 150 microns;
  (c) paper layer thickness NOT less than 80 microns and NOT
      greater than 90 microns

FILM, paper AND polypropylene (PP), having ALL of the following:
  (a) weight NOT less than 144 g per square metre;
  (b) polypropylene (PP) layer thickness NOT less than 111 
      microns and NOT greater than 140 microns;
  (c) paper layer thickness NOT less than 90 microns and NOT 
      greater than 110 microns

FILM, PVC, flexible, in rolls, with OR without finished edges, 
having BOTH of the following:
  (a) reinforced polyester scrim;
  (b) thickness NOT less than 0.55 mm

WATERPROOF MEMBRANE, PVC, EXTRUDED, with OR without polyester 
fleece backing, having a glass fibre fabric AND/OR glass fibre 
fleece reinforcement

SHEETS, polyisobutylene, embedded aluminium mesh, having ALL of 
the following:
  (a) synthetic rubber backing;
  (b) adhesive fixing strips;
  (c) high density polyethylene(HDPE) foil layer;
  (d) colouring pigment;
  (e) ultra-violet stabilising additive

POLYESTER COMPOSITE STRAPPING, including BOTH of the following:  
  (a) width NOT less than 13 mm and NOT greater than 50 mm;
  (b) polypropylene coating

BOARDS, FORMWORK, having ALL of the following:
(a) polypropylene outer;
(b) aluminium OR fibreglass reinforced;
(c) polypropylene OR fibreglass core

FABRIC, polyester, in rolls, having BOTH of the following:
  (a) laminated OR coated polyvinyl chloride on BOTH sides;
  (b) width NOT less than 3.30 m

SHEETING, plastic, having ALL of the following:
  (a) NOT less than three layers of linear low density
      polyethylene;
  (b) NOT less than one layer of woven high density polyethylene
      scrim;
  (c) top layer of laminated UV metallocene film

CONTAINMENT SHEETING, laminated, having ALL of the following: 
  (a) outer layers of low density polyethylene; 
  (b) central high density polyethylene leno weave multifilament
      reinforcing mesh; 
  (c) reinforced eyelet bandings; 
  (d) cold knife cut edge finish; 
  (e) weight NOT less than 150 gsm and NOT greater than 300 gsm; 
  (f) width NOT less than 2 m and NOT greater than 4 m;
  (g) UV additive NOT less than 5%

SHEETS, having ALL of the following:
  (a) NOT less than 66% polyvinyl chloride;
  (b) NOT less than 11% wood powder;
  (c) NOT less than 3% calcium carbonate

BARBECUE HOT PLATE LINERS, reinforced fibreglass with embedded 
polytetrafluoroethylene

SHEETS, thermoplastic polyolefin, laminated, embossed

FILM, FOOD WRAPPING, polypropylene, having BOTH of the following:
  (a) thickness NOT greater than 27 microns;
  (c) seal and peel edgings

FILM, POLYESTER OR POLYURETHANE OR POLYVINYLCHLORIDE, including 
metal micro balls, in rolls, having a width NOT less than 50 cm

FABRIC, polyester, embedded in polyvinyl chloride coated with 
polyvinylidene fluoride

SHEETS, THERMOPLASTIC OLEFIN, with polypropylene foam backing

FILM, comprising aluminium foil core, coated on both sides with 
one or more of the following:
  (a) polyester;
  (b) polyethylene;
  (c) polypropylene

ROLLS, POLYESTER FABRIC, plain weave with twisted yarn, coated 
both sides with polyvinyl chloride, having ALL of the following:
  (a) length NOT less than 246 m;
  (b) width NOT less than 205 cm;
  (c) weight NOT less than 582 gsm and NOT greater than 618 gsm

POLYVINYL CHLORIDE SHEETING, laminated with polypropylene foam

FABRICS, WOVEN POLYESTER, having ALL of the following:
  (a) polyvinyl chloride coatings;
  (b) thickness of NOT less than 0.4 mm and NOT greater
      than 1.4 mm;
  (c) width of NOT less than 1 400 mm and NOT greater 
      than 3 200 mm;
  (d) weight of NOT less than 200 grams per square metre and 
      NOT greater than 1 300 grams per square metre;
  (e) length of NOT less than 30 m

FILM, polyvinyl chloride or polyester, in rolls or sheets, 
having EITHER of the following:
(a) width NOT less than 760 mm in sheet form; 
(b) width NOT less than 1 000 mm in roll form

SHEETS, ACRYLIC, consisting of ALL of the following:
  (a) alumina trihydrate;
  (b) butyl acrylate;
  (c) methyl methacrylate

FILM, TACTILE PRESSURE INDICATING SENSOR

POSTFORMED LAMINATES

FABRIC, POLYESTER, laminated on both sides with polyvinyl 
chloride, having ALL of the following:
  (a) width NOT less than 137 cm;
  (b) length NOT less than 50 m;
  (c) weight NOT less than 430 grams per square metre (gsm) and 
      NOT greater than 480 gsm

FILM, polyvinyl chloride, calendared, in rolls or sheets, having 
BOTH of the following:
  (a) release liner;
  (b)  i) width NOT less than 760 mm in sheet form; OR
      ii) width NOT less than 1000 mm in roll form

SHEETS, JOINTING, consisting of compressed aramid fibre with 
woven steel mesh

FABRIC, POLYPROPYLENE, slitfilm, woven, having a tensile  
strength NOT less than 16.2 kN/m

FABRIC, POLYESTER, coated both sides with polyvinyl chloride,    
having ALL of the following:                                     
  (a) width NOT less than 285 cm;                                
  (b) length NOT less than 48 m;                                 
  (c) thickness NOT less than 0.5 mm;                            
  (d) weight NOT less than 600 grams per square metre and NOT    
      greater than 620 grams per square metre

LAMINATES, comprising BOTH of the following:
  (a) fibrous materials;
  (b) thermosetting resins

TAPE, FABRIC, base coated with semi-conductive plastic

PREPREG SHEETS, being reinforcing fabric of glass fibre, aramid, or
 carbon fibre or combinations thereof, pre impregnated and coated
 with partially cured epoxy resin

CAST LINERS, waterproof

WASH BASINS, polyester resin with aluminium tri-hydrate filler 
composite construction, with OR without integrated splash-back 
AND shelf

WASH BASINS, wall mountable, glass reinforced plastic with a 
polyester gel coating, with OR without integrated splash back 
AND soap shelves

SEATS AND COVERS, TOILET, polypropylene, whether OR not soft 
close, having BOTH of the following:
  (a) hinges;
  (b) fixtures

SEATS, TOILET, urea formaldehyde, having BOTH of the following:
  (a) hinges;
  (b) securing attachments

TOILETS, portable, hand carried, water flushing type,
 self-contained, with a fresh water capacity NOT exceeding 20 L
 and a holding tank capacity NOT exceeding 24 L

SHOWERS, solar, complete with shower nozzle

TOILET PANS, having ALL the following:
  (a) polyester resin AND aluminium tri-hydrate filler composite
      construction;
  (b) with OR without toilet seat AND/OR fixings

TOILET PANS, glass reinforced plastic with a polyester gel 
coating, with OR without spacer box AND/OR toilet seat AND/OR 
infills

TOILET CISTERNS, plastic, including ALL of the following:
  (a) inlet AND outlet valves;
  (b) compliance with NOT less than 1 star rating as required 
      by the Australian/New Zealand Standard AS/NZS  
      6400:2005,table 3.2,
  with OR without ANY of the following:
      (i) toilet seats;
     (ii) connection plates;
    (iii) flushing pipes;
     (iv) flexible stainless braided inlet connector hoses;
      (v) steel support frames;
     (vi) copper OR plastic waste pipe connectors

SLEEVES, URINAL, ODOUR LOCKING, plastic, having anti bacterial 
agents

URINALS, water free

PACKAGING CONTAINERS, thermoplastic polypropylene, collapsible, 
including BOTH of the following: 
  (a) pallet-shaped container base;
  (b) plastic container top

BAGGAGE TRAYS, AIRPORT CONVEYING LINE, moulded polypropylene, 
including ALL of the following:  
 (a) tray dimensions being ALL of the following:  
          (i) length NOT greater than 2 600 mm;  
         (ii) width NOT greater than 900 mm;  
        (iii) height NOT greater than 220 mm  
 (b) tray capacity weight NOT greater than 50 kgs

TRAYS, polypropylene, including ALL of the following:
  (a) length NOT greater than 650 mm;
  (b) width NOT greater than 450 mm;
  (c) height NOT greater than 125 mm;
  (d) floating base;
  (e) barcode tags

FILM CASES, plastic, circular, having BOTH of the following:
  (a) diameter NOT less than 184 mm;
  (b) depth NOT less than 24 mm

TRAYS, STORAGE AND RETRIEVAL, polypropylene OR polypropylene-
talc, including ALL of the following:
  (a) length NOT less than 499 mm;
  (b) width NOT less than 349 mm;
  (c) maximum load capacity NOT less than 55 kg;
  (d) reinforced tray rims

TRAYS, FOOD POUCH HANDLING, stackable, acrylonitrile butadiene 
styrene, having ALL of the following:
  (a) width NOT greater than 1 205 mm;
  (b) length NOT greater than 1 335 mm;
  (c) height NOT greater than 49 mm;
  (d) NOT less than 47 internal pockets;
  (e) contours in the base

TRAYS, EGG HANDLING, stackable, having BOTH of the following:
  (a) dimensions 299 mm x 299 mm x 50 mm;
  (b) net weight 0.144 kg
For the purposes of this order tolerances are allowable for the 
following specifications:
  (a) +/- 1 mm;
  (b) +/- 0.003 kg

STORAGE CONTAINERS, polypropylene, stackable, including ALL of 
the following:
  (a) length NOT less than 590 mm;
  (b) width NOT less than 390 mm;
  (c) height NOT less than 310 mm;
  (d) load carrying capacity NOT less than 50 kg;
  (e) volume NOT less than 60 L

PLATES OR DISHES, LABORATORY, single OR multi-well, well capacity
NOT greater than 25 ml

SETTING AND/OR HATCHING TRAYS, stackable, having ALL of the 
following:
  (a) width NOT greater than 581 mm;
  (b) length NOT greater than 674 mm;
  (c) height NOT greater than 121 mm

BASKETS, HATCHER, stackable, having ALL of the following:
  (a) length NOT greater than 674 mm;
  (b) width NOT greater than 581 mm;
  (c) height NOT greater than 167 mm

TRAYS, stackable, having ALL of the following:
  (a) swing bars AND/OR handles;
  (b) label holders AND/OR recesses;
  (c) length NOT greater than 600 mm;
  (d) width NOT greater than 400 mm

TRAYS, including ALL of the following:
  (a) length NOT greater than 630 mm;
  (b) width NOT greater than 530 mm;
  (c) height NOT greater than 140 mm;
  (d) load weight NOT exceeding 25 kg;
  (e) radio-frequency identification tags

BINS, polypropylene, stackable, being ALL of the following:
  (a) bin height NOT less than 220 mm and NOT greater than 
      330 mm;
  (b) maximum stackable weight NOT greater than 825 kg;
  (c) bin load carrying capacity NOT greater than 30 kg

EGG HANDLING TRAYS, stackable having ALL of the following:
  (a) width NOT greater than 300 mm;
  (b) length NOT greater than 300 mm;
  (c) height NOT greater than 51 mm;
  (d) weight NOT greater than 0.147 kg

CRATES, polypropylene, foldable, stackable, having BOTH of the 
following:
  (a) maximum load weight NOT less than 16 kg per crate;
  (b) ventilated sides AND base

CASES OR TRAYS, COMPACT DISK

PLASTIC PACKAGING CONTAINERS, collapsible, re-usable comprising the
 following features:
   (a) fitted plastic pallet and top lid, formed from high molecular
       weight, high density and polyethylene resin;
   (b) self locking mechanism for block stacking

BOX, cosmetic, plastic, with separate compartments for cosmetics,
 with or without vanity mirror

ORGANISERS, embroidery floss, comprising:
   (a) floss and bobbin container; AND
   (b) NOT less than 50 refill bobbins; OR
   (c) floss winder

CRATES, high density polyethylene(HDPE), stackable, having BOTH 
of the following:
  (a) maximum load carrying capacity NOT less than 7.5 kg;
  (b) ventilated sides AND a non-ventilated base

TRAYS, polypropylene, having BOTH of the following:
  (a) floating interior layer insert;
  (b) maximum load carrying capacity NOT greater than 34 kg

COMPACTS, COSMETIC, plastic

COMPACTS, COSMETIC, plastic, with mirror

CASES, PLASTIC, having BOTH of the following:
  (a) waterproof tested to IPX-8 specification;
  (b) internal dimensions of 
        (i) length NOT exceeding 160 mm;
       (ii) width NOT exceeding 90 mm

PACKAGING CONTAINERS, plastic AND steel, collapsible, with OR 
without disposable inner bags, including ALL of the following:
  (a) plastic pallet shaped container base;
  (b) plastic container top;
  (c) container side metal pole supports;
  (d) stackable interlocking base and top plastic shapes

PACKAGING, FOOD, biodegradable, consisting of moulded corn starch

CONTAINERS, polypropylene, having BOTH of the following:
  (a) tamper evident seal;
  (b) capacity NOT less than 210 ml and NOT greater than
      1 530 ml

BOXES, DIGITAL VERSATILE DISC (DVD)

CONTAINERS, electrostatic shielding, which provides Faraday cage
 effect protection for the contents

BAGS, static shielding, heat sealable, transparent, comprising
 EITHER of the following:
   (a) an antistatic polyethylene inner layer laminated to a
       polyester dielectric layer and vapour coated with a nickel
       or aluminium outer layer, providing a Faraday cage;
   (b) an antistatic polyethylene inner layer laminated to an
       antistatic polyester outer layer between which is a vapour
       coating of aluminium or nickel, providing a Faraday cage

BAGS, storage, blood freezing, incorporating ALL of the following:
   (a) pocket for pilot samples;
   (b) inlet ports;
   (c) outlet ports

BAGS, HDPE, having ALL of the following:
   (a) fully pigmented with calcium carbonate;
   (b) having a permeability to water of less than 0.5 g/m DIN 53122
       at 23 degrees C and 85% relative atmospheric humidity

BAGS, polyethylene, having ALL of the following:
   (a) top perforation, having front pre-opened;
   (b) continuous roll;
   (c) bottom heat sealed;
   (d) printed white label patch

BAGS, BREATHER, LLDPE, two component, having ALL of the following:
   (a) breather component constructed of spun bonded olefin with
       thermoplastic adhesive coating being gas permeable to ethylene
       oxide and NOT permeable to air;
   (b) gurley porosity of the breather component in the range 20 to
       130 seconds (both inclusive);
   (c) fibre free peel-off seal between breather component and
       polyethylene component at a peel strength in the range 178.6
       g/cm to 535.8 g/cm (both inclusive);
   (d) thickness of polyethylene component NOT less than 70 microns
       and NOT exceeding 110 microns

BAGS, FREEZER, high density polyethylene, pre-packed with or without
 ties, thickness 5-9 microns (both inclusive)

POUCHES, surgical, single use composed of plastic film coated wholly
 or partly on one side with a hypoallergenic adhesive having a
 minimum width of NOT less than 15 cm

BAGS, sandwich, high molecular high density polyethylene with a
 fold lock top, thickness 6 to 10 microns in the following size:
   (a) 16 cm x 14 cm

BAGS, FREEZER, high density polyethylene, pre-packed with ties,
 thickness 5-8 micron in ANY of the following sizes plus or minus
 5 mm:
   (a) 25 x 36 cm;
   (b) 20 x 25 cm;
   (c) 30 x 45 cm;
   (d) 25 x 35 cm

LINERS, linen carrier, high density polythene, comprising:
   (a) a vertical overlapped slit covered by a polyvinyl
       alcohol film panel with thickness of 35 micron + or - 10%;
   (b) heat sealed bottom seam

BAGS, freezer, high density polyethylene, blocked, perforated,
 thickness 8 micron to 11 micron, size 25cm x 20cm plus or minus 5 mm

BAGS, produce, high density polyethylene, sealed, perforated,
 thickness 8 micron, on roll

BAGS, FREEZER, high density polyethylene, blocked, perforated,
 thickness 8 micron to 11 micron in EITHER of the following sizes
 plus or minus 5mm:
   (a) 35 cm x 25 cm;
   (b) 45 cm x 30 cm

BIOCONTAINERS, with OR without tubing AND/OR fittings, having 
BOTH of the following: 
  (a) multiple layer film;
  (b) capacity NOT less than 50 millilitres and NOT greater than
      1,000 litres

BAGS, BIOPROCESSING, single use, having ALL of the following:
  (a) single-layer fluoropolymer film;
  (b) gamma-stable;
  (c) capacity NOT less than 20 millilitres and NOT greater than 
       50 litres
with OR without ANY of the following:
        (i) plastic tubes;
       (ii) Plastic tube fittings

ASEPTIC BAGS, bottle-shaped, HDPE  film, including 
ANY of the following:
  (a) rigid collar;
  (b) protective cover;
  (c) flexible sleeve

HEADER BAGS, STERILISATION

KITS, BIOPROCESSING, having ALL of the following:
  (a) multiple layer film bags, having ports;
  (b) plastic tubing;
  (c) plastic tube fittings;
  (d) plastic pinch clamps,
with OR without ANY of the following:
           (i)  plastic rigid rods;
          (ii)  adhesive strips;
         (iii)  filters;
          (iv)  pouches;
           (v)  cable ties;
          (vi)  labels;
         (vii)  irradiation indicators;
        (viii)  rectangular foam packaging inserts;
          (ix)  adhesive strips

LINERS, plastic, cube shaped, having ALL of the following:
  (a) NOT less than 2 layers of film;
  (b) length NOT less than 1 095 mm;
  (c) width NOT less than 1 095 mm;
  (d) height NOT less than 900 mm;
  (e) fill port diameter NOT less than 25 mm;
  (f) outlet port diameter NOT less than 50 mm

HIGH VISCOSITY LINERS, inflatable, linear low-density 
polyethylene (LLDPE), having three layers

PROCESS BAGS, PHARMACEUTICAL, including ALL of the following:
  (a) LDPE OR ULDPE composition;
  (b) gamma irradiated;
  (c) temperature stability NOT exceeding 50 Deg C;
  (d) inlet AND outlet connectors AND tubing;
with OR without ANY of the following:
    (i) clamps;
   (ii) adapters;
  (iii) T AND Y joiners;
   (iv) connectors;
    (v) line tubes;
   (vi) gaskets

BAGS, having a circular collar of hard plastic with a snap-lock 
closure

BAGS, plastic, having ALL of the following:
  (a) polyethylene outer flat layer;
  (b) heat sealed seams;
  (c) polyethylene bubble wrap inner layer;
  (d) bag closing adhesive seal

LINERS, WET FOODSTUFF, high density polyethylene (HDPE), 
having ALL of the following:
  (a) length NOT less than 900 mm;
  (b) width NOT less than 790 mm;
  (c) thickness NOT less than 21 micron;
  (d) minimum 130 g impact when tested using a hemispherical
      dart from a drop height of 660 mm as specified in American 
      Society for Testing and Materials D 1709-03
      (ASTM D 1709-03)

BLADDERS, TANK, low density polyethylene AND ethylene vinyl 
alcohol AND polyamide, multi layered, having a capacity NOT less 
than 250 litres and NOT greater than 1 000 litres

BAGS, square OR rectangular profile, having ALL of the following:
  (a) reinforced self-supporting polypropylene outer container;
  (b) plastic coated inner wall;
  (c) internal liner;
  (d) capacity exceeding 1 000 L

SILAGE BAGS, polyethylene, having All of the following:
  (a) thickness NOT less than 100 micron;
  (b) length NOT less than 45 m;
  (c) width NOT less than 2.5 m

BAGS, PLANTER, woven polyethylene, incorporating handles

BLADDER BAGS, having BOTH of the following:
  (a) body of linear low density polyethylene(LDPE);
  (b) in ANY of the following sizes:
        (i) 20 litres;
       (ii) 15 litres;
      (iii) 10 litres;
       (iv) 5 litres

TUBES, SILAGE, polyethylene, having BOTH of the following:
  (a) length NOT greater than 90 m;
  (b) diameter NOT less than 2.7 m and NOT greater than  2.8 m

ROLL BAGS, plastic, vacuum sealable, food storage, width NOT 
greater than 28 cm

LINERS, BIN, polyethylene, with co-extruded adjacent bands, 
having ALL of the following:
  (a) width NOT greater than 1 200 mm;
  (b) length NOT greater than 1 500 mm;
  (c) thickness NOT less than 6 micron and NOT greater than
      30 micron

BAGS, VACUUM SEALABLE, FOOD STORAGE

BAGS, DRAWTAPE OR DRAWTIGHT, polyethylene, having ALL of the 
following:
  (a) width NOT greater than 64 cm;
  (b) length NOT greater than 85 cm;
  (c) polyethylene film having a thickness NOT less than 6 
      microns and NOT greater than 22 microns

BAGS, DRAWTAPE OR DRAWTIGHT, polyethylene, having All of the 
following:
  (a) width NOT greater than 1 200 mm;
  (b) length NOT greater than 1 500 mm;
  (c) polyethylene film having a thickness NOT less than 10 
      microns and NOT greater than 80 microns

BAGS, FREEZER, high density polyethylene(HDPE), having ALL of 
the following:
  (a) thickness NOT less than 8 microns and NOT greater than
      11 microns;
  (b) width NOT less than 21 cm;
  (c) length NOT greater than 45 cm

BAGS, SILLAGE, low density polyethylene, having BOTH of the
following:                                                 
  (a) length NOT greater than 75 m;                        
  (b) diameter NOT greater than 2.75 m

STORAGE BAGS, VACUUM SEAL, having BOTH of the following:
   (a) one way vacuum seal valve;
   (b) zip lock seal closure

BAGS, polyvinyl chloride, liquid lime putty

BAGS, polypropylene, recloseable, having a push together and pull
 apart seal

POLYVINYl BAG, zip top with internal pocket

BAGS, capable of block forming and vacuum packing of ground coffee,
 having ALL of the following characteristics:
   (a) multi layer composition - 3 ply lamination;
   (b) printed;
   (c) a holding capacity of 250 grams & 500 grams only

PORTABLE STORAGE BAGS, having ALL of the following:
  (a) capacity NOT less than 100 cubic meters;
  (b) inlet AND/OR outlet valves;
  (c) rolling flap having straps

BAGS, OVEN, polyester, heat resistant, having ALL of the 
following:
  (a) length NOT greater than 65 cm;
  (b) width NOT greater than 50 cm;
  (c) thickness NOT less than 11 microns and NOT greater
      than 16 microns

BAGS, polypropylene, having ALL of the following:
  (a) length NOT greater than 23.5 cm;
  (b) width NOT greater than 17 cm;
  (c) handle slot

BAGS, aliphatic polyester

BLADDERS, HYDRATION, comprising ALL of the following:
  (a) mouth pieces;
  (b) bite valves;
  (c) flow tubes

FLASKS, tissue culture, polystyrene, disposable

BOTTLES, roller, tissue culture

BOTTLES, FUEL, plastic, portable, incorporating a screw cap with
 integral pourer, capacity NOT exceeding 1 L

PREFORMED UNEXPANDED BOTTLES, tubular shaped, polyethylene
terephthalate, having ALL of the following:
  (a) inner neck diameter NOT less than 25.10 mm + / - 0.15 mm  
      and NOT greater than 46.15 mm + / - 0.15 mm;
  (b) neck outer diameter NOT less than 27.70 mm + / - 0.15 mm
      and NOT greater than 55.40 mm + / - 0.15 mm;
  (c) neck thread diameter NOT less than 29.40 mm + / - 0.20 mm 
      and NOT greater than 55.45 mm + / - 0.20 mm

GREASE COLLECTION BOTTLES, including BOTH of the following:
  (a) threaded cap;
  (b) hollow bolt with nut AND washers

PLASTIC CONTAINERS, including BOTH of the following:
  (a) threaded closure;
  (b) sieve sleeve AND/OR desiccant liner,
with OR without EITHER of the following:
           (i) lid;
          (ii) seal

PREFORMED UNEXPANDED BOTTLES, tubular shaped, polyethylene 
terephthalate copolymer, having ALL of the following:
  (a) inner neck diameter NOT less than 45.85 mm and NOT greater 
      than 46.15 mm;
  (b) neck outer diameter NOT less than 55.00 mm and NOT greater 
      than 55.40 mm;
  (c) neck thread diameter NOT less than 55.05 mm and NOT 
      greater than 55.45 mm

SQUEEZE BOTTLES, having a threaded neck

SQUEEZE BOTTLES, including nozzle and cap

POUCHES, FOOD AND BEVERAGE, having an inbuilt straw AND/OR neck

VIALS, INJECTION THERAPY, polypropylene, certified to 
International Organization for Standardization ISO 9001 and ISO 
13485, having ANY of the following capacities:
  (a) 2 ml;
  (b) 5 ml;
  (c) 10 ml;
  (d) 20 ml;
  (e) 25 ml;
  (f) 50 ml

POUCHES, FOOD AND BEVERAGE, flexible, reclosable, having BOTH of 
the following:
  (a) inbuilt straw and/or neck;
  (b) tamper evident cap

SPOOLS, computer printer ribbon

REELS, 35 mm OR 70 mm cinematograph projector, but NOT including
 35 mm reels having a maximum capacity of 610 m or less

SPOOLS, magnet winding wire

CAPS, pipette dispensing, gomme button, plunger - actuated
 diaphragm type, of anodised polymers

CLOSURES, pilfer detectable, for drums 20 L and over,
 incorporating a renestable pull up pourer

CAPS AND PLUGS, COUPLING, polypropylene, cam locking

STOPPERS, BOTTLE, swing wire

CAPS, bottle, reusable, incorporating a vent valve and pouring lip

LIDS, agricultural spray chemical tank, polypropylene, incorporating
 ALL of the following features:
   (a) anti-spill safety design;
   (b) air breather valve OR labyrinth;
   (c) direct attachment to tank OR fit with lid nut ring adaptor

CLOSURES, LABORATORY TUBE AND/OR VIAL, being EITHER of the 
following:
  (a) sealing caps;
  (b) sealing sheets having three OR more embedded caps

CEMENTING PLUGS, OIL AND GAS WELL

CLOSURES, TEST TUBE, having BOTH of the following:
  (a) revolver having a diameter of 90 mm AND height of 262 mm;
  (b) closure width NOT less than 10 mm and NOT greater than 
      16 mm

PLUGS, CONTAINER, nylon AND/OR polypropylene, having a threaded 
diameter NOT less than 20 mm, with OR without ANY of the 
following:
  (a) central recesses;
  (b) washers;
  (c) vents

PLUG CAPS, polyethylene, circular, tamper evident having a 
tear-off tab

PLUGS, polyethylene, threaded, diameter NOT less than 20 mm, 
with OR without ANY of the following:
  (a) central recesses;
  (b) washers;
  (c) vents

CAPS, threaded, having BOTH of the following:
  (a) tamper evident seal;
  (b) cutter teeth

LIDS AND/OR COVERS, CONTAINER, OVEN AND MICROWAVE COOKWARE, 
liquid crystal polymer (LCP)

CAPS, PLASTIC BOTTLE, threaded

CAPS AND/OR LIDS, LIP BALM HOLDER, plastic

CLOSURES, PUSH-PULL SLIDER, aseptic cold fill, having ALL of the 
following:
  (a) polyethylene pourer with moulded tamper-evident band and
      bore seal;
  (b) polypropylene tamper-evident dust overcap;
  (c) internal pressure rating NOT less than 200 kPa

LIDS, HINGED, FOUR WHEELED GARBAGE BIN, high density 
polyethylene (HDPE), complying with Australian Standard AS 
4123.2-2008, having a length NOT greater than 1090 mm or NOT 
less than 1190 mm and having ANY of the following:
  (a) width NOT greater than 650 mm;
  (b) width NOT less than 710 mm and NOT greater than 950 mm;
  (c) width NOT less than 1010 mm

PRESSURE SEALS, PLASTIC BAG, zip fasten, co-extruded 
polypropylene, resealable

LIDS, polypropylene, microwavable, having BOTH of the following:
 (a) pressure release outlet;
 (b) silicone seal

LIDS, DRINKING CUP, disposable, biodegradable, corn starch 
polymer

COVERS, CAN, plastic

GRIPS, PLASTIC BAG CLOSURE, single moulded, comprising ALL of 
the following:
  (a) two plastic clamping members;
  (b) plastic hinges;
  (c) plastic springs

CLOSURES, BOTTLE, wine, synthetic cork

CLOSURES, LAMINATED PAPERBOARD PACKAGING, comprising BOTH of the
 following:
   (a) low density polyethylene re-sealable pourer, comprising BOTH
       of the following:
         (i) induction heated polyethylene fusion flange;
        (ii) impermeable ring-pull inner barrier;
   (b) linear low density polyethylene cap with safety seal

CLOSURES, resealable zip-fastener, co-extruded polyethylene, in
 rolls having a width NOT less than 4 mm and NOT greater than 24 mm

CAPS, BOTTLE, flip top

CAPS, LIQUID FOOD AND JUICE PACKAGE, hot melt application, having
 a rim and recloseable lid

BOATS, reagent, automatic biochemistry analysis machine

TRAYS, cuvette, blood serum analyser, incorporating 100 cuvettes

CUVETTES, blood serum analyser

TUBES, cryogenic, polypropylene, screw closure

CARD SLEEVES, polypropylene, having ALL of the
following:
  (a) NOT less than 50 sleeves;
  (b) gloss OR matte finish;
  (c) clear OR block colour OR printed art finish;
  (d) dimensions NOT less than 41 x 53 mm and NOT greater than
      82 x 122 mm

PHARMACEUTICAL BIOPROCESSING CONTAINERS, having top AND bottom 
steel plates, with OR without EITHER of the following:
  (a) cryo-foam inlays;
  (b) partial fill foam

PALLETS, EGG HANDLING, reinforced, with OR without dividers, 
having BOTH of the following:
  (a) pallet dimension 1 200 mm x 90 mm x 16 mm;
  (b) reinforced net weight 20 400 kg,
For the purposes of this order the following tolerances apply:
         (i) (a) +/- 1 cm;
        (ii) (b) +/- 300 gm

SOLID LAYER PADS, injection moulded co-polymer propylene, having 
ALL of the following:
  (a) ultra violet stabiliser;
  (b) length NOT less than 1 400 mm;
  (c) width NOT less than 1 000 mm;
  (d) thickness over edge profile NOT less than 2.5 mm and 
      NOT greater than 13 mm;
  (e) conforming to BOTH of the following:
         (i) Commission Regulation (EU) 10/2011 on plastic 
             material and articles intended to come into  
             contact with food;
        (ii) one OR more of the following:
                (A) Regulation (EU) 1935/2004 of the European 
                    Parliament and of the Council;
                (B) Commission Directive 93/9/EEC (1993);
                (C) Commission Directive 95/3/EC (1995)

CONTAINERS, FOOD, thermo-formed polypropylene, having ALL of the 
following:
  (a) hinged lid with vents;
  (b) offset tabs;
  (c) single OR multiple compartments

TUBES, polypropylene, threaded, with OR without ANY of the 
following:
  (a) barcodes;
  (b) caps;
  (c) jackets whether OR not co-moulded;
  (d) lid locks;
  (e) racks;
  (f) tube locks;
  (g) twist locks

EGG HANDLING PALLETS, stackable, with OR without dividers, 
having ALL of the following:
  (a) width NOT greater than 910 mm;
  (b) length NOT greater than 1 210 mm;
  (c) height NOT greater than 170 mm;   
  (d) weight NOT greater than 17.5 kg

TRAYS AND/OR PALLETS, EGG HANDLING, stackable, with OR without 
dividers, having EITHER of the following: 
  (a) tray AND/OR pallet 30 cm x 30 cm weight of 144 g; 
  (b) tray AND/OR pallet 120 cm x 90 cm having ANY of the
      following weights;
         (i) 11 300 g;
        (ii) 14 000 g;
       (iii) 17 500 g
For the purposes of this order, tolerances allowable for 
specification 
(a) +/- 2 g
(b) -200 g

HOLDERS, LIP BALM, plastic, with OR without caps

SHELLS, COFFEE CAPSULE, plastic

PACKAGING RINGS, CAN, polyethylene

HOLDERS, LIPSTICK, plastic

TRAYS, BOTTLE, plastic, stackable, having segregated bottle base 
compartments for bottles with diameter NOT less than 90 mm and 
NOT greater than 113 mm

SLEEVES, PACKAGING, polyethylene terephthalate, printed, in 
rolls, perforated, having ALL of the following:
  (a) film thickness NOT less than 46 micrometers;
  (b) transversal shrinkage to 90 degrees Celsius NOT less 
      than 76%;
  (c) sleeve width NOT greater than 61 mm

HANGERS, FOOTWEAR, plastic

JARS AND JAR LIDS, plastic, including BOTH of the following:
  (a) acrylic outer layer;
  (b) polypropylene with ultra violet metallised finish inner
      layer

CONTAINERS, CRYOGENIC TUBE, polypropylene, sterile

TUBES, BLOOD COLLECTION, polypropylene

MICRO TUBES, polypropylene, with OR without caps

TUBES, low-density polyethylene, having a scored tip

TUBES, CENTRIFUGE, having screw caps

CONTAINERS, egg shaped, polypropylene, opening AND closing

CONTAINERS, FOOD, poly lactic acid, incorporating a dome shaped 
lid

CONTAINERS, moulded pvc, with watertight screw top lid

MODULAR DISHWASHER RACKS, CONVEYOR DISHWASHER

TABLEWARE, melamine, trays with decorative printed designs

PRESS, plastic, garlic

PARTS FOR CHILD SAFETY AND HYGIENE PRODUCTS, being ANY of the
 following interchangeable parts for a training cup system:
   (a) drinking cup with handles;
   (b) screw on babies nursing nipple and cover;
   (c) screw on spout;
   (d) screw on straw;
   (e) screw on drink training lid and storage lid

CHILD SAFETY AND HYGIENE PRODUCTS, being a cutlery set comprising
 knife, fork or spoon imported EITHER individually or in sets, with
 or without container

DRYING RACKS, BABY BOTTLE, vented, including removable AND 
adjustable pegs

TRAYS, HEATED AND REFRIGERATED MEAL DELIVERY TROLLEY, polyester 
resin, fibreglass AND aluminium hydroxide, being ANY of the 
following sizes:
  (a) 525 mm x 325 mm;
  (b) 575 mm x 325 mm; 
  (c) 530 mm x 325 mm;
  (d) 265 mm x 325 mm
For the purposes of this order, tolerance allowable for 
specifications (a) to (d) are +/- 1 mm.

CONTAINERS, KITCHENWARE, polyethylene, food storage, having ALL 
of the following:
  (a) transparent base;
  (b) coloured lid;
  (c) capacity NOT greater than 3 litres

DISPENSER, polypropylene, including BOTH of the following:
  (a) serrated cutting edge;
  (b) polyethylene film in a roll, having ALL of the following:
        (i) thickness NOT less than 9 microns and NOT greater
            than 12 microns;
       (ii) width NOT greater than 33 cm;
      (iii) length NOT greater than 90 m

COLD BREW COFFEE MAKERS, immersion, having ALL of the following:
  (a) extraction chamber;
  (b) brewing chamber;
  (c) micro-mesh stainless steel filter;
  (d) twist cap

CONTAINERS, plastic, having BOTH of the following:
  (a) ventilated lid;
  (b) volume capacity NOT less than 2.5 L and NOT greater 
      than 9 L

CONTAINERS, KITCHENWARE, FOOD STORAGE AND/OR MARINATING, vacuum 
seal, with OR without hoses

PRESSURE COOKERS, MICROWAVE, having ALL of the following:
  (a) base;
  (b) cover;
  (c) safety lock handle;
  (d) safety lock plug;
  (e) pressure regulator valves;
  (f) pressure indicators;
  (g) silicone cover gasket

CONTAINERS, OVEN AND MICROWAVE COOKWARE, liquid crystal 
polymer (LCP), with OR without ANY of the following:
  (a) lids;
  (b) steam vents;
  (c) handles

CAKE TURNTABLES

SETS, COOKWARE, MICROWAVE, with OR without cover lids, being 
EITHER of the following:
  (a) stack cookers, having ALL of the following:
       (i)   casserole dishes;
       (ii)  baking cones;
       (iii) colanders;
       (iv)  storage seals,
  (b) steamers, having ALL of the following:
       (i)   colander trays;
       (ii)  steamer bases;
       (iii) water trays

MEASURING JUGS, plastic, including BOTH of the following:
  (a) lid;
  (b) handle

CONTAINERS, SQUEEZABLE, FROZEN AND/OR CHILLED BEVERAGE AND/OR 
DESSERT MAKING, having a lining filled with a salt solution, 
with OR without ANY of the following:
  (a) lids;
  (b) straws;
  (c) spoons

EGG COOKERS, MICROWAVE

KITCHENWARE, being novelty shaped sandwich cutters

SETS, KITCHENWARE, consisting of ALL of the following:
  (a) icing AND/OR cookie shaping gun;
  (b) icing nozzles;
  (c) cookie discs

KITCHENWARE, plastic, being EITHER of the following:
  (a) food pan lids;
  (b) food drain plates

CONTAINERS, FRESH HERB STORAGE, plastic

CONTAINERS, KITCHENWARE, plastic, in the shape of fruit AND/OR 
vegetables

PANS, FOOD STORAGE, polycarbonate AND/OR polypropylene

KITCHENWARE, being piping syringes having BOTH of the following:
  (a) decorating tips;
  (b) storage clips

KITCHENWARE, being drying racks OR holders depicting ANY of the 
following:
  (a) grass;
  (b) twigs;
  (c) stems

CUTLERY, plastic, being ANY of the following:
  (a) knives;
  (b) forks;
  (c) spoons

ICING BAGS, CAKE DECORATING, plastic

SETS, CAKE DECORATING, silicone, being icing bags

BAGS, ICING, plastic coated cotton cloth

TABLEWARE AND/OR KITCHENWARE, being ANY of the following:
  (a) fondant decorating rolling pins;
  (b) cake fondant smoothers;
  (c) cake fondant imprint mats;
  (d) letter and number impressions;
  (e) fondant ribbon cutters;
  (f) cake decorating turntables;
  (g) fondant modelling tools;
  (h) silicone mats;
  (i) rolling pin guides

PEELERS, GARLIC, silicone

PRESSES, HAMBURGER PATTY, plastic

CUPS, EGG

OPENERS, BOTTLE AND/OR JAR, HAND GRIP, silicone

KITCHENWARE, being cake OR pudding moulds

KITCHENWARE, HEAT SHIELDING, silicone, being EITHER of the 
following:
  (a) hand fitting grippers;
  (b) cylindrical shaped handle sleeves

KITCHENWARE, being juicers, having BOTH of the following:
  (a) strainer;
  (b) juice holder

TABLEWARE AND/OR KITCHENWARE, being cake decorating pens

SLICER AND WEDGE CUTTERS, BOILED EGG, plastic, incorporating 
metal cutting wires

SETS, COOKIE CUTTERS

DISPLAY STANDS, CUPCAKE AND/OR SWEETS AND/OR PARTY FOOD, plastic

TABLEWARE AND/OR KITCHENWARE, being concertinaed piping 
containers with nozzle

TABLEWARE AND/OR KITCHENWARE, being ANY of the following:
  (a) pot lid stand AND spoon rest;
  (b) herb infuser;
  (c) cake divider

KITCHENWARE, being ANY of the following:
  (a) wrapping AND/OR foil holders;
  (b) jelly OR pastry OR cake pudding moulds;
  (c) paper towel holders;
  (d) salad washers;
  (e) shakers;
  (f) trivets;
  (g) turkey basters;
  (h) food ties

TABLEWARE, plastic, being ANY of the following:
  (a) trivets;
  (b) cruets;
  (c) gravy OR sauce boats;
  (d) chopsticks;
  (e) chopstick rests

KITCHENWARE, silicone, being moulds

SETS, KITCHENWARE, plastic, consisting of BOTH of the 
following:  
   (a) cake decorators, manually operated, having ALL of 
       the following:
          (i) handles;
         (ii) plungers;
        (iii) internal reservoirs, 
   (b) interchangeable nozzles

TABLEWARE AND/OR KITCHENWARE, being ANY of the following:
  (a) tongs;
  (b) lettuce knives;
  (c) cake slicers

KITCHENWARE, being shakers with measuring increments, capacity 
NOT greater than 500 ml

TABLEWARE AND/OR KITCHENWARE, being ANY of the following:
  (a) scoops AND slicers;
  (b) adjustable measuring spoons;
  (c) serving spoons;
  (d) turners;
  (e) tea strainers;
  (f) mashers;
  (g) food covers;
  (h) ladles

TABLEWARE AND KITCHENWARE, being cherry AND/OR olive pitters

TABLEWARE AND KITCHENWARE, being spatulas

FOOD COLLECTOR SETS, consisting of BOTH of the following:
  (a) silicone mat with metal bar;
  (b) plastic container AND/OR colander

TABLEWARE AND/OR KITCHENWARE, being plastic juicers having ALL 
of the following:
  (a) cover;
  (b) juicer;
  (c) cup

TABLE AND/OR KITCHENWARE, being plastic salad servers

TABLEWARE AND/OR KITCHENWARE, being plastic food storage 
containers including BOTH of the following:
  (a) fitted fork;
  (b) inbuilt condiment holder

TABLEWARE AND/OR KITCHENWARE, being plastic cake servers

KITCHENWARE, plastic, being measuring beakers, whether OR not in 
sets

TABLEWARE AND/OR KITCHENWARE, being combination skimmer 
AND colander

TABLEWARE AND/OR KITCHENWARE, plastic, being ANY of the 
following:
  (a) combination turner AND scoop;
  (b) combination masher AND scraper;
  (c) beakers, having BOTH of the following:
          (i) spouts;
         (ii) graduations,
  (d) bowls, having BOTH of the following:
          (i) spouts;
         (ii) rubber gripping feet,
  (e) racks, having BOTH of the following:
          (i) drain spout;
         (ii) removable utensil holder

KITCHENWARE, being plastic ice block moulds

SETS, KITCHENWARE, consisting of NOT less than 4 measuring cups

CUTLERY, plastarch material (PSM), disposable

TABLEWARE AND/OR KITCHENWARE, being ANY of the following:
  (a) measuring spoons;
  (b) slotted spoons;
  (c) slotted turners;
  (d) spatulas and/or scrapers;
  (e) serving spoons

PADS, TABLEWARE AND/OR KITCHENWARE, silicone, incorporating a 
magnet

SCOOPS, plastic

DISPOSABLE CUPS, TABLEWARE AND/OR KITCHENWARE, polylactide

PLACEMATS AND/OR COASTERS

TABLEWARE AND/OR KITCHENWARE, melamine, being ANY of the 
following:
  (a) basting spoons;
  (b) slotted spoons;
  (c) turners and/or spatulas;
  (d) slotted turners;
  (e) ladles;
  (f) spaghetti servers;
  (g) mixing bowls

BAGS, PIPING, having interchangeable nozzles

PLATES AND CUTLERY, disposable, consisting of corn starch polymer

TABLEWARE AND/OR KITCHENWARE, plastic, being ANY of the 
following:
  (a) microwave plate covers;
  (b) pastry mats;
  (c) splatter screens or guards;
  (d) table cloth clamps

TRAYS, MEAL, polyester resin and fibreglass

BAGS, PIPING, disposable, with nozzles

TRAYS, ICE CUBE, flexible

SETS, KITCHEN TOOLS, plastic, comprising NOT less than ANY three 
of the following:
  (a) skimmer;
  (b) tongs;
  (c) ladle;
  (d) whisk;
  (e) potato masher;
  (f) spatula;
  (g) spaghetti server;
  (h) spoon;
  (i) fork;
  (j) egg flip or egg turner

KITCHENWARE, plastic, being ANY of the following:
(a)whisks;
(b)spatulas;
(c)scrapers;
(d)spaghetti servers;
(e)hand held juicers

SCOOPS, FOOD

TABLEWARE AND/OR KITCHENWARE, KNIVES AND/OR FORKS AND/OR SPOONS, 
disposable, poly lactic acid

COLANDERS, polypropylene, folding

PLACEMATS, polypropylene, plaited

CUP AND CAP, BABY DRINKING, spill proof

MEASURES, INGREDIENTS, HAND HELD, adjustable

RESTRAINER SEATS, BABIES BATH, with suction cups on underside

WATER BOTTLES, plastic, portable, incorporating a screw on lid,
 having BOTH of the following:
   (a) push-pull, non-leak cap;
   (b) porous, carbon membrane, micro filter

PLACEMATS, vinyl, depicting cartoon characters

BOTTLES, baby, calibrated to a capacity LESS than 125ml

BABY BOTTLES, measured to 60 mls or 250 mls

SHOE HORN, plastic

BOTTLES, baby, measured to 240 ml

BOTTLES, BABY FEEDING, polypropylene, printed, calibrated

CHILD SAFETY AND HYGIENE PRODUCTS, comprising drinking beakers with
 leak proof lids and plastic straws

CHILD SAFETY AND HYGIENE PRODUCTS, being feeding bottles
 calibrated to 60 ml, 125 ml, 250 ml, and/or 280 ml, imported singly
 or in sets, having at least THREE of the following:
   (a) locking ring/collar;
   (b) sealing disc;
   (c) teat;
   (d) protective travel hood;
   (e) training spout;
   (f) bottle handles

CHILD SAFETY AND HYGIENE PRODUCT, being a toilet training seat
 having BOTH of the following features:
  (a) portable;
  (b) padded

CHILD SAFETY AND HYGIENE PRODUCTS, toilet, portable, multi-stage

CHANGE MATS, polyurethane foam with timber insert

STEAM STERILISERS, BABY BOTTLE, including removable AND 
adjustable pegs, with OR without pacifier

BABY BOTTLE FEEDING SETS, including ALL of the following:
  (a) bottles;
  (b) breast pump adapters;
  (c) pacifier;
  (d) bottle brushes,
with OR without ANY of the following:
          (i) teats;
         (ii) storage caps;
        (iii) travel covers;
         (iv) warming bowl;
          (v) steam sterilizer;
         (vi) drying rack

TABLECOVERS, textured vinyl top surface with 100% polyester
 non-woven backing, NOT exceeding 3 metres in length

STORAGE BOXES, SHOE, plastic, ventilated

BOTTLES, CARBONATING, BEVERAGE, co-polyester, with OR without 
caps

APPLIQUES, BATH TUB, non slip vinyl composition, EITHER in shapes
 OR strips

BOTTLES, CARBONATING BEVERAGE, polyethylene terephalate  (PET), 
with OR without caps

SETS, RUBBISH BIN, cupboard OR closet mounted, including ALL of 
the following:
  (a) covers;
  (b) mountings;
  (c) drawer sliders;
  (d) brackets;
  (e) plastic buckets

CONTAINERS, FRESH FRUIT AND VEGETABLES, plastic, whether OR not 
in sets, having ALL of the following:
  (a) transparent base;
  (b) coloured lid having an air vent with slider;
  (c) in-mould pictograms;
  (d) capacity NOT exceeding 9.9 litres

SHOWER HEADS, ABS (Acrylonitrile Butadiene Styrene), chrome 
plated, ball joint swivel connector

BAGS, MILK STORAGE, having ALL off the following:
  (a) polyester outer lining;
  (b) polyethylene inner lining;
  (c) capacity graduations;
  (d) zip top closure

STEAM CLEANING BAGS, MICROWAVE, having BOTH of the following:
  (a) zip lock closure;
  (b) steam vent incorporating a pouring outlet

HANDHELD SHOWER ASSEMBLIES, with OR without soap dish, having 
two OR more of the following:
  (a) plastic AND/OR metal shower head;
  (b) metal shower rail;
  (c) metal AND/OR plastic hose;
  (d) wall connector

BOTTLES, DRINKING, having a copolyester body

HOUSEHOLD ARTICLES, being razor blade cleaners AND preservers 
including razor holder

BOTTLES, DRINKING, plastic, including ALL of the 
following:
  (a) flip-top screw cap;
  (b) pop-up drinking straw;
  (c) titled embossed wrap

TUBS, polypropylene, flexible, having moulded handles

BINS, DISPOSABLE NAPPY WRAPPING, with removable cassette, with 
OR without replacement cassettes

BUCKETS, WRINGER MOP, plastic, incorporating a wringer mechanism

BOTTLES, DRINKING, polyethylene terephthalate glycol (PETG), 
including ALL of the following:
  (a) bite valve;
  (b) folding spout;
  (c) removable straw

SUPPORTS, BABY BATH, plastic, incorporating suction cups on  
underside

BOTTLES, HOT WATER, polyvinylchloride, with stopper

ASSEMBLIES, HANDHELD SHOWER, including ALL of the following:
  (a) plastic shower head;
  (b) metal shower rail;
  (c) metal AND/OR plastic flexible hose

MUGS, TRAVEL, having ALL of the following:
   (a) foam OR double wall insulated;
   (b) tapered body;
   (c) lid

CHILDREN'S STEP STOOLS, plastic, having a height NOT greater 
than 200 mm

STRAINERS, DRAIN, SINK AND/OR BATH, plastic

BAGS, MILK STORAGE, polyethylene, having a capacity NOT less 
than 200 ml

SPOUTS, TODDLER FEEDING BOTTLE, plastic, incorporating a valve

DISPENSERS, BABY FORMULA, plastic, having BOTH of the following:
  (a) NOT less than three baby formula holding compartments;
  (b) dispensing spout and spout lid

MATS, PET, polypropylene

BOTTLES, sports, insulated, polyvinyl chloride (PVC) covered, having
 a push/pull non-leak cap

TOILETS, CHILDRENS, portable, leak proof

HOLDERS, TABLECLOTH, comprising plastic clips and metal weights

BATHROOM AND/OR TOILET ARTICLES, polypropylene, being ANY of the 
following:
  (a) combined toothbrush and toothpaste container;
  (b) toothbrush container and soap container;
  (c) toothbrush container;
  (d) soap container

MATS, polyvinyl chloride, non-slip, length NOT greater than
820 mm

HOOKS, HANGING, plastic, S shaped

SCOOPS, PET LITTER

PLUGS, SINK AND/OR BATH, plastic

TROLLEY BINS, polypropylene, having ALL of the following;
  (a) NOT less than three handles;
  (b) NOT less than four wheels;
  (c) hinged lid;
  (d) height not exceeding 100 cm

CONTAINERS, DISPOSAL, CIGARETTE ASH AND BUTT

STORGE BOXES, SHOE, plastic, ventilated

LITTER TRAYS, CAT, plastic enclosed, portable, with active 
carbon filter and scoop

TABLECOVERS AND/OR TABLESKIRTS, polyethylene

STORAGE BOXES, SHOE, polypropylene, ventilated

SPONGES, plastic

HOUSEHOLD ARTICLES, plastic, being ANY of the following:
  (a) organisers;
  (b) cosmetic holders;
  (c) jewellery holders;
  (d) cleaning aid holders;
  (e) stationery holders;
  (f) paper towel holders;
  (g) toilet roll holders;
  (h) toilet brush holders;
  (i) toothbrush holders;
  (j) jewellery stands;
  (k) soap dishes or soap savers

TEATS, baby

BATHROOM AND/OR TOILET ARTICLES, being ANY of the following:
  (a) bath and/or shower caddies;
  (b) organisers;
  (c) baskets;
  (d) cups

DISPENSERS, PLASTIC BAG RECYCLING

DRYER BALLS, plastic

BANKS, PIGGY, personalised

ARTICLES, HOUSEHOLD, suction mounted, being ANY of the 
following:
  (a) shower caddies;
  (b) bath caddies;
  (c) organisers;
  (d) holders;
  (e) hooks; 
  (f) baskets;
  (g) soap dishes;
  (h) soap cradles;
  (i) shelves;
  (j) toothbrush/razor holders with cup;
  (k) plastic mirrors

SHOWER HEADS, HAND HELD

RECEPTACLES, DISPOSABLE NAPPY, having ALL of the following:
  (a) removable top with flip top lid;
  (b) spring loaded jaws;
  (c) replaceable cassette;
  (d) fixed childproof plastic film cutter

TOILET TRAINERS, CAT, comprising a three piece seat assembly

CASSETTES, DISPOSABLE NAPPY AND/OR DIAPER RECEPTACLE

BOTTLES, baby, polycarbonate, printed, calibrated to a capacity of
 either 150 ml or 300 ml

LOCKS, CHILD SAFETY, moulded plastic, being EITHER of the following:
   (a) magnetically activated;
   (b) adjustable external handle

CHILD SAFETY PRODUCTS, moulded plastic, being ANY of the following:
   (a) cabinet, drawer and cupboard spring latches;
   (b) door stoppers;
   (c) toilet lid lock;
   (d) electricity outlet cover plugs;
   (e) appliance latches;
   (f) oven locks;
   (g) video cassette recorder locks;
   (h) table and shelf corner cushions;
   (i) door knob covers;
   (j) cord winders;
   (k) electric cord plug clamps;
   (l) stove knob covers;
   (m) tap and spout covers

APPLIQUES, BATH TUB, non slip vinyl composition, EITHER in shapes
 OR strips

JEWELLERY BOXES, MUSICAL

BAG LINER CARTRIDGES, DIAPER DISPOSAL

TABLECOVERS, textured vinyl top surface with 100% polyester
 non-woven backing, NOT exceeding 3 metres in length

VESSELS, off-ground, glass reinforced plastic

VESSELS, HYDROCHLORIC ACID FUME EXTRACTION SCRUBBER OR 
SEPARATOR, polypropylene

TANKS, GLASSHOUSE LIQUID FERTILISER AND/OR WATER TREATMENT, 
polyethylene, including ALL of the following:
  (a) lid AND/OR manhole;
  (b) fluid level signal AND/OR empty alarm;
  (c) venturi flow control compartment

GAS STORAGE TANKS, double membrane, including ALL of the 
following:
  (a) outer membrane;
  (b) inner membrane;
  (c) air flow unit;
  (d) air maintenance valve;
  (e) support air blower;
  (f) anchor ring;
  (g) safety valve;
  (h) inspection window;
  (i) level meter

TANKS OR SILOS, hot press moulded glass reinforced fibre, round, 
capacity NOT less than 300 L

JAMBLINERS, PVC, with snap on flanges

DOORS, AIRCRAFT HANGAR, vertical folding, comprising ALL of the 
following:
  (a) centre door;
  (b) two inner doors;
  (c) two outer doors;
  (d) swing up mullions

VERTICAL LIFTING DOORS, having ALL of the following:
  (a) fabric AND aluminium door leaf;
  (b) drive unit;
  (c) lifting belt AND/OR cable;
  (d) control unit;
  (e) steel bottom section;
  (f) guide rail

SUBMARINE VIEWPORTS, acrylic

DOORS, AIRCRAFT HANGAR, vertical folding, comprising ALL of the 
following:
  (a) centre door;
  (b) two inner doors;
  (c) two outer doors;
  (d) swing up mullions

DOORS, PET, door OR window OR wall mounted

PARTS, AWNING, being ANY of the following:
  (a) adaptors;
  (b) caps;
  (c) crowns;
  (d) crank rod clips;
  (e) idler plate

PARTS, BLINDS, being ANY of the following:
  (a) caps;  
  (b) cleats;
  (c) clips;
  (d) clutches;
  (e) connectors;
  (f) controllers;
  (g) cord equaliser;
  (h) cord stops;
  (i) cord toggles;
  (j) covers;  
  (k) idlers;  
  (l) mechanisms; 
  (m) separator;
  (n) slat hangers;
  (o) splines;
  (p) stoppers;
  (q) strip;
  (r) adaptors;
  (s) brackets;
  (t) carriers;
  (u) chain;
  (v) loops;
  (w) weights

PARTS, VERTICAL BLIND, being slat travellers

PARTS, BLIND, ROLLER, being ANY of the following:
  (a) adaptors;
  (b) brackets;
  (c) caps;
  (d) clutches;
  (e) controllers;
  (f) cord stops;
  (g) housings;
  (h) pull balls;
  (i) winders

CHILD SAFETY PRODUCTS, being a security gate, having ALL of the
 following features:
   (a) adjustable length of 66 cm to 107 cm, both inclusive
       +/- 2 cm;
   (b) affixable by pressure or bracket to railings, doorways and
       walls;
   (c) portable

HOOKS, plastic, having removable adhesive backing

PIPE AND/OR VALVE ACCESSORIES, plastic, being EITHER of the 
following:
  (a) pipe clips;
  (b) mounting clips

WALLBOXES, rectangular, PVC, having ALL of the following:
  (a) length NOT greater than 100 mm;
  (b) depth NOT greater than 45 mm;
  (c) sliding nuts;
  (d) NOT greater than 5 inlets;
  (e) one gang

COVER PLATES, POWER POINT

BUILDERS WARES, being sliding door corner stakes

MOUNTS, DECORATIVE WALL PANEL, plastic, being EITHER of the 
following:
   (a) panel securing buttons AND/OR mounts;
   (b) panel marking indenters

HOLDERS, WRAPPING AND/OR FOIL AND/0R PAPER TOWEL, wall mounted

BATHROOM AND/OR TOILET ARTICLES, being ANY of the following:
  (a) holders;
  (b) robe hooks;
  (c) soap dishes and/or cradles;
  (d) toothbrush and/or razor holders with or without cups;
  (e) towel rails and/or rings;
  (f) toilet roll and/or brush holders

GRATINGS, FIBREGLASS REINFORCED PHENOLIC RESIN, being EITHER of 
the following; 
 (a)floor panels;          
 (b)stair treads

HOLDERS, TOWEL, adhesive backed

HOOKS, plastic, self-adhesive

TEA TOWEL HOLDERS