Tariff Concession Orders

ADHESIVES, cyanoacrylate monomer based

LOCKING COMPOUND, ANAEROBIC, METHACRYLATE

RETAINING COMPOUND, ANAEROBIC, METHACRYLATE

SEALANT, ANAEROBIC, METHACRYLATE

ADHESIVES, ANAEROBIC, METHACRYLATE

ADHESIVE, knife grade, flexible bonding, having ALL of the
 following:
   (a) one-part formulation;
   (b) moisture curing;
   (c) 40 minutes tack-free time @ 20 degrees C and 65% relative
       humidity;
   (d) 300% or greater, elongation at break (DIN 53 504);
   (e) 4 N/mm2 tensile strength (DIN 53 504);
   (f) 9 N/mm tear propagation strength (DIN 53 515);
   (g) 55 + or - 3 degrees shore A hardness (DIN 53 505)
 For the purposes of this Order, tolerances of + or - 10% are
 allowable

ADHESIVE, POLYURETHANE BASED, one part formulation, having ALL
 of the following:
   (a) tack free time between 60 minutes and 130 minutes,
       at temperatures NOT lower than 20 degrees C
       and relative humidity between 50% and 60%;
   (b) 200% OR greater, elongation at break (DIN 53504);
   (c) tensile strength NOT less than 1.0 N/mm sq and NOT exceeding
       2.5 N/mm sq (DIN 53504);
   (d) shore A hardness 30 degrees and NOT exceeding 60 degrees
       (DIN 53505)

ADHESIVE, WINDSCREEN, moisture curing, polyurethane based

ADHESIVE, high green and cured strength, having ALL the following
 properties:
   (a) single component elastomeric moisture curing polyurethane;
   (b) tack free time @ 23 degrees C and 50% relative humidity
       approx 40 min;
   (c) shore A hardness 55 +/- 3 degrees          DIN 53 505;
   (d) elongation at break > 300%                 DIN 53 504;
   (e) tensile strength 6 +/- 0.2 mPa             DIN 53 504;
   (f) tear propagation strength 8 +/- 1 N/mm     DIN 53 515;
   (g) electrical resistance 1,000,000 ohms cm approx;
   (h) produces no corrosive fumes when spot welded through in the
       uncured state;
   (i) able to form a gas and liquid tight seal while bonding

ADHESIVE, hot melt, in the form of solid cylinders NOT less than
 10 cm and NOT exceeding 12 cm in length, having a diameter NOT
 exceeding 8 mm

ADHESIVES, epoxy, being ALL of the following:
   (a) one component adhesive;
   (b) heat activated curing;
   (c) fluorescent under black light

ADHESIVE, CONVEYOR BELT, being repair kits, having ALL of the 
following:
  (a) liquid resin having a basis of polymer;
  (b) catalyst having a basis of diethylmethylbenzenediamine;
  (c) cleaning solvent;
  (d) primer having a basis of ethyl acetate;
  (e) mixing spatula;
  (f) application brush;
  (g) latex gloves

SEALANTS AND/OR ADHESIVES, hybrid polymer, having BOTH of the 
following:
  (a) shore A hardness 50 +/- 5%; 
  (b) volume change less than 2%

SEALANTS AND/OR ADHESIVES, having a silane modified polymer base

SEALANTS AND/OR ADHESIVES, having BOTH of the following:
  (a) polyurethane base;
  (b) skin formation NOT greater than 61 minutes

GLUE, polymer

ADHESIVES OR GLUE, FINGERNAIL

ADHESIVE, cyanoacrylate, including a primer

SEALANTS AND/OR ADHESIVES, having ALL of the following:
  (a) silane modified polymer base;
  (b) tooling time NOT greater than 61 minutes at 23 degrees 
      Celsius AND 50% relative humidity;
  (c) density NOT less than 1.3 grams per cubic centimetre

ADHESIVES, peelable, including a polyethylene film top layer and 
EITHER of the following:
  (a) adhesive coated siliconised sheets AND/OR strips;
  (b) adhesive coated polyethylene sheets AND/OR strips

GLUE STICKS, retractable

ADHESIVES, EYELASH

ADHESIVES, CONCRETE AND/OR MASONRY, vinyl ester, two part glass 
capsule

ADHESIVES, CONCRETE AND/OR MASONRY, vinyl ester, styrene free, 
two component cartridge

ADHESIVES, CONCRETE AND/OR MASONRY, two part epoxy

ADHESIVES, CONCRETE AND/OR MASONRY, polyester resin

ADHESIVES, silane modified polymer

ADHESIVE, PIPE LINING, polyurethane, conforming to Australian 
and New Zealand standard AS/NZS 4020:2018

TAPE, double side adhesive, having ALL of the following:
  (a) tissue paper backing;
  (b) polyethylene liner paper;
  (c) acrylic OR rubber base glue

ADHESIVE, waterborne, having a basis of  polychloroprene

ADHESIVES, water based polymer

ADHESIVE TRANSFER FILM, having ALL of the following:
  (a) poly acrylic adhesive;
  (b) glassine paper double sided siliconised liner;
  (c) polyethylene plastic

SEALANT, ANAEROBIC, METHACRYLATE

ADHESIVES, ANAEROBIC, METHACRYLATE

ADHESIVES, LAMINATING, two component polyurethane, solvent free

TRANSPARENT TRANSFER ADHESIVE, polyacrylate based, elastic, PH
 neutral, interleaved with disposable release medium

DISPERSION GLUE, being EITHER of the following:
   (a) polyvinyl alcohol; OR
   (b) polyvinyl acetate base

ADHESIVES, formulated for bonding elastomers to metal during
 vulcanisation

ADHESIVES, having a basis of synthetic rubber dispersed in water

ADHESIVES, pressure sensitive, hot melt

ADHESIVES, polyethylene resin, in pellets, having BOTH of the 
following:
  (a) melt index at 190 degrees Centigrade NOT less than 1.4
      and NOT greater than 1.8 degrees per minute;
  (b) tensile strength at break NOT less than 150 kg/sq cm

ADHESIVE, hot melt, ethylene-vinyl acetate based

ADHESIVE WEB, polyamide, in rolls, whether OR not paper-backed

TAPE, double sided, acrylic adhesive, polyethylene laminated 
kraft paper liner

ADHESIVES, cyanoacrylate monomer based

SEALANTS, silicon based